Search NASA⌕ Search

SEARCH · Search NASA

Results for “insertion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

Development of PET/MRI with insertable PET for simultaneous PET and MR imaging of human brain

Purpose: The purpose of this study was to develop a dual-modality positron emission tomography (PET)/magnetic resonance imaging (MRI) with insertable PET for simultaneous PET and MR imaging of the human brain. Methods: The PET detector block was composed of a 4 × 4 matrix of detector modules, each consisting of a 4 × 4 array LYSO coupled to a 4 × 4 Geiger-mode avalanche photodiode (GAPD) array. The PET insert consisted of 18 detector blocks, circularly mounted on a custom-made plastic base to form a ring with an inner diameter of 390 mm and axial length of 60 mm. The PET gantry was shielded with gold-plated conductive fabric tapes with a thickness of 0.1 mm. The charge signals of PET detector transferred via 4 m long flat cables were fed into the position decoder circuit. The flat cables were shielded with a mesh-type aluminum sheet with a thickness of 0.24 mm. The position decoder circuit and field programmable gate array-embedded DAQ modules were enclosed in an aluminum box with a thickness of 10 mm and located at the rear of the MR bore inside the MRI room. A 3-T human MRI system with a Larmor frequency of 123.7 MHz and inner bore diameter of 60 cm was used as the PET/MRI hybrid system. A custom-made radio frequency (RF) coil with an inner diameter of 25 cm was fabricated. The PET was positioned between gradient and the RF coils. PET performance was measured outside and inside the MRI scanner using echo planar imaging, spin echo, turbo spin echo, and gradient echo sequences. MRI performance was also evaluated with and without the PET insert. The stability of the newly developed PET insert was evaluated and simultaneous PET and MR images of a brain phantom were acquired. Results: No significant degradation of the PET performance caused by MR was observed when the PET was operated using various MR imaging sequences. The signal-to-noise ratio of MR images was slightly degraded due to the PET insert installed inside the MR bore while the homogeneity was maintained. The change of gain of the 256 GAPD/scintillator elements of a detector block was <3% for 60 min, and simultaneous PET and MR images of a brain phantom were successfully acquired. Conclusions: Experimental results indicate that a compact and lightweight PET insert for hybrid PET/MRI can be developed using GAPD arrays and charge signal transmission method proposed in this study without significant interference.

60 APPLIED LIFE SCIENCES↗

An Insertion Mutation That Distorts Antibody Binding Site Architecture Enhances Function of a Human Antibody

The structural and functional significance of somatic insertions and deletions in antibody chains is unclear. Here, we demonstrate that a naturally occurring three-amino-acid insertion within the influenza virus-specific human monoclonal antibody 2D1 heavy-chain variable region reconfigures the antibody-combining site and contributes to its high potency against the 1918 and 2009 pandemic H1N1 influenza viruses. The insertion arose through a series of events, including a somatic point mutation in a predicted hot-spot motif, introduction of a new hot-spot motif, a molecular duplication due to polymerase slippage, a deletion due to misalignment, and additional somatic point mutations. Atomic resolution structures of the wild-type antibody and a variant in which the insertion was removed revealed that the three-amino-acid insertion near the base of heavy-chain complementarity-determining region (CDR) H2 resulted in a bulge in that loop. This enlarged CDR H2 loop impinges on adjacent regions, causing distortion of the CDR H1 architecture and its displacement away from the antigen-combining site. Removal of the insertion restores the canonical structure of CDR H1 and CDR H2, but binding, neutralization activity, and in vivo activity were reduced markedly because of steric conflict of CDR H1 with the hemagglutinin antigen.

59 BASIC BIOLOGICAL SCIENCES↗

Sequential cooling insert for turbine stator vane

A sequential flow cooling insert for a turbine stator vane of a small gas turbine engine, where the impingement cooling insert is formed as a single piece from a metal additive manufacturing process such as 3D metal printing, and where the insert includes a plurality of rows of radial extending impingement cooling air holes alternating with rows of radial extending return air holes on a pressure side wall, and where the insert includes a plurality of rows of chordwise extending second impingement cooling air holes on a suction side wall. The insert includes alternating rows of radial extending cooling air supply channels and return air channels that form a series of impingement cooling on the pressure side followed by the suction side of the insert.

33 ADVANCED PROPULSION SYSTEMS↗

Flex plate with removable inserts and cover

Technologies are described for methods and systems effective for flex plates. The flex plates may comprise a base plate. The base plate may include walls that define an insert location opening in the base plate. The insert location opening in the base plate may be in communication with a securement area. The flex plates may comprise an insert. The insert may include a reservoir region and a crystallization region separated by a wall including channels. The reservoir region and the crystallization region may include a backing. The insert may further include securement tabs. The securement tabs may be configured to secure the insert to the base plate at the securement area.

42 ENGINEERING↗

Flex plate with removable inserts and cover

Technologies are described for methods and systems effective for flex plates. The flex plates may comprise a base plate. The base plate may include walls that define an insert location opening in the base plate. The insert location opening in the base plate may be in communication with a securement area. The flex plates may comprise an insert. The insert may include a reservoir region and a crystallization region separated by a wall including channels. The reservoir region and the crystallization region may include a backing. The insert may further include securement tabs. The securement tabs may be configured to secure the insert to the base plate at the securement area.

Soares, Alexei S.↗

Criticality Scoping Calculations for a Multi-Function Dissolver Insert

As one of its missions, the Savannah River Site seeks to be a leader in the safe and productive disposition of special nuclear materials. One of the premier programs is the disposition of used nuclear fuel, primarily from research reactors, through dissolution, purification, and down blend into low enriched uranium for commercial power reactors. Prior to use, this fuel contained highly enriched uranium (HEU). In an effort to advance this expertise, this study has been performed to demonstrate the feasibility to disposition a number of special geometry HEU fuels. These fuels come from a number of different domestic and foreign research reactors which had geometries considerably different from round or square bundles of plates or rods. As such, they cannot be dispositioned in current H-Canyon dissolver inserts so a new, multi-function dissolver insert may be considered. While this is not a current mission, it is believed that this study's scoping calculations demonstrate the feasibility of the site taking such a mission. At the H-Canyon facility, a dissolver is a large stainless steel pot, loaded with a nitric acid solution into which uranium-alloy fuel is dissolved. The dissolver uses a device called an insert to feed the fuels to the acid solution in a controlled manner. Most fuel forms fit into one of the existing inserts which include one with ten {approx}5-inch diameter circular wells, one with four {approx}4.5 inch by {approx}15 inch slab wells, and one specifically designed for the Oak Ridge National Laboratory High Flux Isotope Reactor (HFIR). This study considered five bounding fuel candidates for scoping the potential new insert. The fuels include a generic annular plate fuel (APF), the Tower Shield Reactor (TSR) fuel elements, the Reactor A Haute Flux (RHF) core, Knolls Atomic Power Laboratory (KAPL) reactor fuel, and SLOWPOKE cores. These are expected to bound a range of proposed fuel candidates. Scoping studies were made to establish geometric restrictions for the new dissolver insert and to determine if these fuels could safely be dissolved. Homogenous models were used for the scoping study due to time constraints. Computational modeling was performed using KENOVI in the SCALE 6.1 code package.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Wire-coil insert optimization for high-heat-load/flux synchrotron components

Many synchrotron components require high levels of internal-flow, forced-convection heat transfer to minimize surface temperatures, thermal gradients, and thermally induced stress on high-power beam-interacting surfaces. Wire-coil inserts, physically similar to a common spring, are mechanically fitted inside of component cooling passages to optimize heat transfer performance. They are routinely used in Advanced Photon Source (APS) front end and beamline high-heat-load/flux components to significantly enhance convection heat transfer-up to 400% compared to plain open passages. This has the additional benefit of greatly reducing coolant flow requirements for these components. Using several cooling passage sizes, five different wire sizes, and a range of pitch values, an experimental investigation conducted at the APS has determined the average heat transfer coefficient and resulting pressure loss as a function of water flow rate for 65 different wire-coil inserts. Data from this study have been non-dimensionalized and generalized to yield relationships that can be used to determine the heat transfer performance and resulting pressure loss for any given wire-coil insert that may be used at the APS. Through data reduction, the wire-coil insert characteristic dimensions have also been optimized to yield the highest heat transfer enhancement while minimizing the coolant flow requirements. These generalized expressions for wirecoil inserts will be presented, and they can be used by scientists and engineers during the component design process to evaluate achievable heat transfer performance and associated pressure loss, aiding in the establishment of optimized operating parameters and cooling passage flow distribution schemes.

43 PARTICLE ACCELERATORS↗

Selectivity of Electrochemical Ion Insertion into Manganese Dioxide Polymorphs

The ion insertion redox chemistry of manganese dioxide has diverse applications in energy storage, catalysis, and chemical separations. Unique properties derive from the assembly of Mn–O octahedra into polymorphic structures that can host protons and nonprotonic cations in interstitial sites. Despite many reports on individual ion-polymorph couples, much less is known about the selectivity of electrochemical ion insertion in MnO 2 . In this work, we use density functional theory to holistically compare the electrochemistry of A x MnO 2 (where A = H + , Li + , Na + , K + , Mg 2+ , Ca 2+ , Zn 2+ , Al 3+ ) in aqueous and nonaqueous electrolytes. We develop an efficient computational scheme demonstrating that Hubbard-U correction has a greater impact on calculating accurate redox energetics than choice of exchange-correlation functional. Using PBE+U, we find that for nonprotonic cations, ion selectivity depends on the oxygen coordination environments inside a polymorph. When H + is present, however, the driving force to form hydroxyl bonds is usually stronger. In aqueous electrolytes, only three ion-polymorph pairs are thermodynamically stable within water’s voltage stability window (Na + and K + in α-MnO 2 , and Li + in λ-MnO 2 ), with all other ion insertion being metastable. We find Al 3+ may insert into the δ, R, and λ polymorphs across the full 2-electron redox of MnO 2 at high voltage; however, electrolytes for multivalent ions must be designed to impede the formation of insoluble precipitates and facilitate cation desolvation. We also show that small ions coinsert with water in α-MnO 2 to achieve greater coordination by oxygen, while solvation energies and kinetic effects dictate water coinsertion in δ-MnO 2 . Finally, taken together, these findings explain reports of mixed ion insertion mechanisms in aqueous electrolytes and highlight promising design strategies for safe, high energy density electrochemical energy storage, desalination batteries, and electrocatalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Membrane insertion for the detection of lipopolysaccharides: Exploring the dynamics of amphiphile-in-lipid assays

Shiga toxin-producing Escherichia coli is an important cause of foodborne illness, with cases attributable to beef, fresh produce and other sources. Many serotypes of the pathogen cause disease, and differentiating one serotype from another requires specific identification of the O antigen located on the lipopolysaccharide (LPS) molecule. The amphiphilic structure of LPS poses a challenge when using classical detection methods, which do not take into account its lipoglycan biochemistry. Typically, detection of LPS requires heat or chemical treatment of samples and relies on bioactivity assays for the conserved lipid A portion of the molecule. Our goal was to develop assays to facilitate the direct and discriminative detection of the entire LPS molecule and its O antigen in complex matrices using minimal sample processing. To perform serogroup identification of LPS, we used a method called membrane insertion on a waveguide biosensor, and tested three serogroups of LPS. The membrane insertion technique allows for the hydrophobic association of LPS with a lipid bilayer, where the exposed O antigen can be targeted for specific detection. Samples of beef lysate were spiked with LPS to perform O antigen specific detection of LPS from E. coli O157. To validate assay performance, we evaluated the biophysical interactions of LPS with lipid bilayers both in- and outside of a flow cell using fluorescence microscopy and fluorescently doped lipids. Our results indicate that membrane insertion allows for the qualitative and reliable identification of amphiphilic LPS in complex samples like beef homogenates. In addition, we also demonstrated that LPS-induced hole formation does not occur under the conditions of the membrane insertion assays. Together, these findings describe for the first time the serogroup-specific detection of amphiphilic LPS in complex samples using a membrane insertion assay, and highlight the importance of LPS molecular conformations in detection architectures.

59 BASIC BIOLOGICAL SCIENCES↗

Complications Associated with the Percutaneous Insertion of Fiducial Markers in the Thorax

PurposeRadiosurgery requires precise lesion localization. Fiducial markers enable lesion tracking, but complications from insertion may occur. The purpose of this study was to describe complications of fiducial marker insertion into pulmonary lesions.Materials and MethodsClinical and imaging records of 28 consecutive patients with 32 lung nodules or masses who underwent insertion of a total of 59 fiducial markers before radiosurgery were retrospectively reviewed.ResultsEighteen patients (67%) developed a pneumothorax, and six patients (22%) required a chest tube. The rates of pneumothorax were 82% and 40%, respectively, when 18-gauge and 19-gauge needles were used for marker insertion (P = 0.01). Increased rate of pneumothorax was also associated with targeting smaller lesions (P = 0.03) and tumors not in contact with the pleural surface (P = 0.04). A total of 11 fiducials (19%) migrated after insertion into the pleural space (10 markers) or into the airway (1 marker). Migration was associated with shorter distances from pleura to the marker deposition site (P = 0.04) and with fiducial placement outside of the target lesion (P = 0.03).ConclusionFiducial marker placement into lung lesions is associated with a high risk of pneumothorax and a risk of fiducial migration.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Phosphatidylserine Asymmetry Promotes the Membrane Insertion of a Transmembrane Helix

The plasma membrane (PM) contains an asymmetric distribution of lipids between the inner and outer bilayer leaflets. A lipid of special interest in eukaryotic membranes is the negatively charged phosphatidylserine (PS). In healthy cells, PS is actively sequestered to the inner leaflet of the PM, but PS redistributes to the outer leaflet when the cell is damaged or at the onset of apoptosis. Yet, the influence of PS asymmetry on membrane protein structure and folding are poorly understood. The pH low insertion peptide (pHLIP) adsorbs to the membrane surface at a neutral pH, but it inserts into the membrane at an acidic pH. We have previously observed that in symmetric vesicles, PS affects the membrane insertion of pHLIP by lowering the pH midpoint of insertion. In this work, we researched the effect of PS asymmetry on the membrane interaction of pHLIP. We developed a modified protocol to create asymmetric vesicles containing PS and employed Annexin V labeled with an Alexa Fluor 568 fluorophore as a new probe to quantify PS asymmetry. We observed that the membrane insertion of pHLIP was promoted by the asymmetric distribution of negatively charged PS, which causes a surface charge difference between bilayer leaflets. Our results indicate that lipid asymmetry can modulate the formation of an α-helix on the membrane. A corollary is that model studies using symmetric bilayers to mimic the PM may fail to capture important aspects of protein-membrane interactions.

59 BASIC BIOLOGICAL SCIENCES↗

Design optimization of integrated cooling inserts in modular Fischer-Tropsch reactors

Sustainable production of liquid fuels and feedstocks from atmospheric CO 2 through carbon recycling technologies is necessary to broaden decarbonization efforts and further reduce global emissions. Fischer–Tropsch (FT) reactors can address this challenge by providing storable, high-value liquid hydrocarbon fuels and feedstocks from syngas generated through reductive CO 2 utilization. FT technology, however, is most cost effective at large-scale, fixed-site plants and does not effectively address the smaller, globally distributed CO 2 point sources. Alternatively, smaller, modular reactors can be composed together to the specific scale of the emission source, yielding a flexible solution that enables more widespread deployment. In these modular reactors, thermal management using a finned cooling insert embedded within the catalyst matrix is critical to maintaining the performance and viability. Thus, in this work, topology optimization is used to determine the cooling insert geometry that maximizes reactor productivity while preventing auto-thermal runaway. Optimal designs are generated for varying number of constituent fins and over a range of maximum operating temperatures. Constraints including minimum feature length-scales and prescribed cooling insert material are imposed on the designs to enhance manufacturability. The impact of design features such as insert tapering and increased length scale hierarchy is automatically revealed by the systematic design framework employed. Here, this approach thus generates novel optimal geometries while automating, accelerating, and enhancing the design process compared to traditional heuristic approaches for cooling insert design in modular FT reactors.

30 DIRECT ENERGY CONVERSION↗

Insertion of Ag atoms into layered MoO{sub 3} via a template route

Graphical abstract: PVP–Ag{sup +} complex self-assembled with inorganic (Mo{sub x}O{sub y}){sub ∞}{sup n−} chains into a layered hybrid, in which the PVP–Ag complex was intercalated between the (Mo{sub x}O{sub y}){sub ∞}{sup n−} layers. Calcinations of this hybrid at 500 °C lead to formation of Ag/MoO{sub 3} nanohybrid. By this method we have successfully inserted Ag atoms into the semiconductor MoO{sub 3} lattice. Display Omitted Highlights: ► We fabricated a PVP–Ag/polyoxomolybdate layered hybrid via in situ self-assembly. ► The PVP–Ag complex has been inserted between the molybdenum oxide layers. ► This layered hybrid transformed into Ag/MoO{sub 3} nanocomposite after calcinations. ► HR-TEM images show that Ag atoms of about 1 nm have been inserted in the MoO{sub 3} layers. -- Abstract: We report insertion of Ag atoms into layered MoO{sub 3} via an in situ template route. PVP–Ag{sup +} complex self-assembled with inorganic (Mo{sub x}O{sub y}){sub ∞}{sup n−} chains into a layered hybrid, in which the PVP–Ag complex was intercalated between the (Mo{sub x}O{sub y}){sub ∞}{sup n−} layers. Calcinations of this hybrid at 500 °C lead to formation of Ag/MoO{sub 3} hybrid, in which Ag nanoparticles of about 1 nm have been inserted between the MoO{sub 3} layers. By this method pillared MoO{sub 3} has been obtained very easily. We believe that this research opens new routes to fabricate novel intercalation compounds and metal/semiconductor nanohybrids via an efficient and green route.

36 MATERIALS SCIENCE↗

Acquisition of a novel eleven amino acid insertion directly N-terminal to a tetrabasic cleavage site confers intracellular cleavage of an H7N7 influenza virus hemagglutinin

A critical feature of highly pathogenic avian influenza viruses (H5N1 and H7N7) is the efficient intracellular cleavage of the hemagglutinin (HA) protein. H7N7 viruses also exist in equine species, and a unique feature of the equine H7N7 HA is the presence of an eleven amino acid insertion directly N-terminal to a tetrabasic cleavage site. Here, we show that three histidine residues within the unique insertion of the equine H7N7 HA are essential for intracellular cleavage. An asparagine residue within the insertion-derived glycosylation site was also found to be essential for intracellular cleavage. The presence of the histidine residues also appear to be involved in triggering fusion, since mutation of the histidine residues resulted in a destabilizing effect. Importantly, the addition of a tetrabasic site and the eleven amino acid insertion conferred efficient intracellular cleavage to the HA of an H7N3 low pathogenicity avian influenza virus. Our studies show that acquisition of the eleven amino acid insertion offers an alternative mechanism for intracellular cleavage of influenza HA.

60 APPLIED LIFE SCIENCES↗

Energetics of Lithium Insertion into Magnetite, Defective Magnetite, and Maghemite

At low concentrations of lithium insertion into inverse spinel magnetite Fe 3 O 4 , a phase change to rock-salt-like Li x Fe 3 O 4 has been observed. Here, we used density-functional-theory-based (DFT-based) calculations to study the structural origins of this phase change, the concentration at which it occurs, the role of iron vacancies, and the stability of the various motifs that form during the electrochemical reduction process in the Li–Fe–O ternary space up to x = 1.33. We compared our results to new experimental measurements of the open circuit voltage for 8–9 nm magnetite particles over a comparable range of lithium insertion. Of the vacant sites in magnetite (16c, 8b, and 48f) lithium insertion was found to be most stable on 16c. Coulomb interactions between the added lithium and iron at the 8a site in magnetite led to substantial displacement of the iron. As further lithium was added, the most energetically favored motif involved lithium clustering in 16c sites around the shifted 8a iron up to a total of three lithiums. In competition with the lithium clustering motif, lithium insertion could be accompanied by the full displacement of all 8a iron to 16c sites, to form the rock-salt-like Li x Fe 3 O 4 , saturating at x = 1. The defective rock-salt structure was found to be more stable than the lithium clustering motif for x ≥ 0.5. The rock-salt-like LiFe 3 O 4 was found to be stable in the Li–Fe–O ternary space for a continuous range of Li–Fe organization on the 16c sites, stabilized by Coulomb interactions. For x < 1, neither the lithium clustering motif, nor the defective rock-salt-like structure for LixFe 3 O 4 were stable against phase segregation to LiFe 3 O 4 and Fe 3 O 4 . This phase segregation (0 < x < 1) occurred at a predicted voltage of ~2.0 V. However, when iron vacancies on the 16d site were introduced, lithium insertion to those vacant 16d sites in Fe 2.875 O 4 , and γ-Fe 2.67 O 4 (maghemite), resulted in stable intercalated materials at a predicted voltage of ~3.0 V. Beyond the concentration of such iron vacancy sites, phase segregation was predicted to the rock-salt-like Li 1.125 Fe 2.875 O 4 and Li 1.33 Fe 2.67 O 4 , again at ~2.0 V. These results were consistent with measured open circuit voltages. Finally, the relative stability for several lithium compositions along the FeO to LiFeO 2 tie line in the defective rock-salt structure suggested stable compound formation for a range of lithium–iron compositions, but without long-range order in the cation sublattice, consistent with what has been commonly observed in the literature.

36 MATERIALS SCIENCE↗

Carbon Dioxide Insertion into Rhenium Hydrides as a Probe for the Impact of Solvent on Linear Free Energy Relationships between Thermodynamic and Kinetic Hydricity

The kinetics of CO 2 insertion into electronically different Re( R bpy)(CO) 3 H ( R bpy = 4,4'-R-2,2'- bipyridine; R = OMe, t Bu, Me, H, Br, COOMe, CF 3 ) complexes to form Re( R bpy)(CO) 3 {OC(H)O} compounds were determined in acetone, dimethylacetamide (DMAc), dimethylformamide (DMF), dimethylsulfoxide (DMSO), and 3-methoxypropionitrile (3-MPN) and compared with previous data in acetonitrile (MeCN). The rates of CO 2 insertion for any one complex of the type Re(Rbpy)(CO) 3 H in different solvents correlates with the Dimroth-Reichardt (E T (30)) solvent parameter. Hammett plots in each solvent indicate that insertion reactions are faster for bpy ligands with electron-donating groups. There is, however, no correlation between the slope of the Hammett plot in different solvents and any common solvent parameter. Similarly, the enthalpies and entropies of activation and kinetic isotope effects associated with CO 2 insertion into Re(bpy)(CO) 3 H in different solvents do not correlate with any common solvent parameters. Theoretical calculations were used to determine the relative thermodynamic hydricities of Re( R bpy)(CO) 3 H type complexes in MeCN, acetone, DMF, and DMSO and in each solvent complexes with more electron-donating substituents on the bpy ligand are stronger hydride donors. Linear Free Energy Relationships (LFERs) between calculated thermodynamic and experimental kinetic hydricity, as measured through CO 2 insertion reactions, were observed in MeCN, acetone, DMF, and DMSO. Furthermore, the slopes of the LFERs correlate with the dielectric constant of the solvent. Overall, this work provides fundamental information about the thermodynamics and kinetics of hydride transfer reactions in different solvents, which is valuable for catalyst design.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Electrochemical ion insertion from the atomic to the device scale

Electrochemical ion insertion involves coupled ion–electron transfer reactions, transport of guest species and redox of the host. The hosts are typically anisotropic solids with 2D conduction planes but can also be materials with 1D or isotropic transport pathways. These insertion compounds have traditionally been studied in the context of energy storage but also find extensive applications in electrocatalysis, optoelectronics and computing. Recent developments in operando, ultrafast and high-resolution characterization methods, as well as accurate theoretical simulation methods, have led to a renaissance in the understanding of ion-insertion compounds. In this Review, we present a unified framework for understanding insertion compounds across timescales and length scales ranging from atomic to device levels. Using graphite, transition metal dichalcogenides, layered oxides, oxyhydroxides and olivines as examples, we explore commonalities in these materials in terms of point defects, interfacial reactions and phase transformations. We illustrate similarities in the operating principles of various ion-insertion devices, ranging from batteries and electrocatalysts to electrochromics and thermal transistors, with the goal of unifying research across disciplinary boundaries.

36 MATERIALS SCIENCE↗

Targeted DNA insertion in plants

Conventional methods of DNA sequence insertion into plants, using Agrobacterium -mediated transformation or microprojectile bombardment, result in the integration of the DNA at random sites in the genome. These plants may exhibit altered agronomic traits as a consequence of disruption or silencing of genes that serve a critical function. Also, genes of interest inserted at random sites are often not expressed at the desired level. For these reasons, targeted DNA insertion at suitable genomic sites in plants is a desirable alternative. In this paper we review approaches of targeted DNA insertion in plant genomes, discuss current technical challenges, and describe promising applications of targeted DNA insertion for crop genetic improvement.

Dong, Oliver Xiaoou↗