Search NASA⌕ Search

SEARCH · Search NASA

Results for “interior point method”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

Laser-induced magnetic fields in ICF capsules, Final Report, DE-FG02-08ER85128, Phase 1

Laser-induced magnetic fields in ICF capsules Final Report, DE-FG02-08ER85128, Phase 1 E. L. LINDMAN, Otowi Technical Services, Los Alamos, NM. The performance of an inertial-confinement-fusion (ICF) capsule can be improved by inserting a magnetic field into it before compressing it [Kirkpatrick, et al., Fusion Technol. 27, 205 (1995)]. To obtain standoff in an ICF power generator, a method of inserting the field without the use of low-inductance leads attached to the capsule is desired. A mechanism for generating such a field using a laser was discovered in Japan [Sakagami, et al., Phys. Rev. Lett. 42, 839 (1979), Kolodner and Yablonovitch, Phys. Rev. Lett. 43, 1402 (1979)] and studied at Los Alamos in the 1980s [M. A. Yates, et al., Phys. Rev. Lett. 49, 1702 (1982); Forslund and Brackbill, Phys. Rev. Lett. 48, 1614 (1982)]. In this mechanism, a p-polarized laser beam strikes a solid target producing hot electrons that are accelerated away from the target surface by resonant absorption. An electric field is created that returns the hot electrons to the target. But, they do not return to the target along the same trajectory on which they left. The resulting current produces a toroidal magnetic field that was observed to spread over a region outside the hot spot with a radius of a millimeter. No experimental measurements of the magnetic field strength were performed. Estimates from computer simulation suggest that field strengths in the range of 1 to 10 Mega gauss (100 to 1000 Tesla) were obtained outside of the laser spot. To use this mechanism to insert a magnetic field into an ICF capsule, the capsule must be redesigned. In one approach, a central conductor is added, a toroidal gap is cut in the outer wall and the DT fuel is frozen on the inner surface of the capsule. The capsule is dropped into the reaction chamber and struck first with the laser that generates the magnetic field. The laser hot spot is positioned at the center of the toroidal gap. As the magnetic field spreads from the hot spot over the surface that contains the toroidal gap, it will propagate through the gap and set up a steady state in the capsule. The main compression is then initiated. First, it closes the gap and crow-bars the field, then it compresses the fuel to ignition. In addition to this application, we discuss the use of this mechanism to induce Mega-gauss fields in laboratory apparatus for measurements of the effects of large magnetic fields on material samples. A preliminary target design for this purpose is presented. It is made of high-density material with no hydrogen surface contamination to minimize fast ion losses and to minimize x-ray preheat of the sample (the material, whose magnetic properties are to be measured). In it, the gap is designed to allow the magnetic field to move into the interior of the target while minimizing the flow of hot electrons into the interior. By adjusting the size of the gap as well as its configuration, the hot electron effects can be minimized. Since the strength of the magnetic field depends on the radial distance to the sample from the center of the conductor carrying the return current, the sample is located at a point of minimum conductor radius. This location also minimizes the effects on the measurement of any hot electrons that flow into the interior. Useful experiments can be accomplished with the “seed” field alone in this geometry. Compressing the capsule after the insertion of the seed field may allow experiments with even larger magnetic fields. We have used computer-simulation techniques to address a number of issues. Our conclusions include: • This magnetic-field generating mechanism is a viable method for generating magnetic fields in ICF targets and for laboratory experiments. • Useful experiments on material samples can be done with the seed field of 1 to10 Mega gauss (100 to 1000 Tesla) and higher magnetic fields can be obtained by subsequently compressing the capsule. • The results reported here can be studied experimentally with a modest CO2 laser that emits 4.5 J of energy in a 1-ns pulse focused into a 60-μm-diameter spot. • We have reproduced the published calculation of Forslund and Brackbill and extended the results to relativistic hot electrons. The difference in our peak magnetic field (1.25 Mg) versus that in the published calculation (1.3 Mg) is negligible. • We have shown that hot electrons can jump a gap while the magnetic field penetrates through the gap into an internal region. • We find that background plasma or a plasma gradient near the accelerating region is essential to the formation of the magnetic-field structures. • And, we have identified resistive losses in the surface return current as a serious issue that must be addressed in future work.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

THE DEVELOPMENT OF A PARAMETERIZED SCATTER REMOVAL ALGORITHM FOR NUCLEAR MATERIALS IDENTIFICATION SYSTEM IMAGING

This report presents a novel method for removing scattering effects from Nuclear Materials Identification System (NMIS) imaging. The NMIS uses fast neutron radiography to generate images of the internal structure of objects nonintrusively. If the correct attenuation through the object is measured, the positions and macroscopic cross sections of features inside the object can be determined. The cross sections can then be used to identify the materials, and a 3D map of the interior of the object can be reconstructed. Unfortunately, the measured attenuation values are always too low because scattered neutrons contribute to the unattenuated neutron signal. Previous efforts to remove the scatter from NMIS imaging have focused on minimizing the fraction of scattered neutrons that are misidentified as directly transmitted by electronically collimating and time tagging the source neutrons. The parameterized scatter removal algorithm (PSRA) approaches the problem from an entirely new direction by using Monte Carlo simulations to estimate the point scatter functions (PScFs) produced by neutrons scattering in the object. PScFs have been used to remove scattering successfully in other applications, but only with simple 2D detector models. This work represents the first time PScFs have ever been applied to an imaging detector geometry as complicated as the NMIS. By fitting the PScFs using a Gaussian function, they can be parameterized, and the proper scatter for a given problem can be removed without the need for rerunning the simulations each time. In order to model the PScFs, an entirely new method for simulating NMIS measurements was developed for this work. The development of the new models and the codes required to simulate them are presented in detail. The PSRA was used on several simulated and experimental measurements, and chi-squared goodness of fit tests were used to compare the corrected values to the ideal values that would be expected with no scattering. Using the PSRA resulted in an improvement of the chi-squared test by a factor of 60 or more when applied to simple homogeneous objects.

Grogan, Brandon R↗

The Development of a Parameterized Scatter Removal Algorithm for Nuclear Materials Identification System Imaging

This dissertation presents a novel method for removing scattering effects from Nuclear Materials Identification System (NMIS) imaging. The NMIS uses fast neutron radiography to generate images of the internal structure of objects non-intrusively. If the correct attenuation through the object is measured, the positions and macroscopic cross-sections of features inside the object can be determined. The cross sections can then be used to identify the materials and a 3D map of the interior of the object can be reconstructed. Unfortunately, the measured attenuation values are always too low because scattered neutrons contribute to the unattenuated neutron signal. Previous efforts to remove the scatter from NMIS imaging have focused on minimizing the fraction of scattered neutrons which are misidentified as directly transmitted by electronically collimating and time tagging the source neutrons. The parameterized scatter removal algorithm (PSRA) approaches the problem from an entirely new direction by using Monte Carlo simulations to estimate the point scatter functions (PScFs) produced by neutrons scattering in the object. PScFs have been used to remove scattering successfully in other applications, but only with simple 2D detector models. This work represents the first time PScFs have ever been applied to an imaging detector geometry as complicated as the NMIS. By fitting the PScFs using a Gaussian function, they can be parameterized and the proper scatter for a given problem can be removed without the need for rerunning the simulations each time. In order to model the PScFs, an entirely new method for simulating NMIS measurements was developed for this work. The development of the new models and the codes required to simulate them are presented in detail. The PSRA was used on several simulated and experimental measurements and chi-squared goodness of fit tests were used to compare the corrected values to the ideal values that would be expected with no scattering. Using the PSRA resulted in an improvement of the chi-squared test by a factor of 60 or more when applied to simple homogeneous objects.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Nanoindentation of Micrograins in Polycrystals under Multiaxial Stress: Control of Abrupt & Stochastic Plastic Events

Deforming objects in the world of the small has proven a much more complex task than just bending a common-sized object like a spoon. Over the last decade, it has become clear that the application of stress on micron-sized objects, such as micropillars, leads to abrupt and stochastic plastic strain jumps that do not satisfy Weibull statistics (as expected for uncorrelated defect yielding) but instead seem to follow highly wide, power-law distributions, pointing towards cooperative dislocation plasticity. Are power-law distributed plastic events the rule or the exception in crystals? If the rule, can we design protocols to control and suppress them in order to achieve deterministic and smooth microforming processes? We propose to combine experiments and theory to unravel the mysteries of abrupt microplastic deformation in a natural dislocation environment: micron-sized grains (\micrograins") of polycrystals. We propose a novel experimental design that utilizes nanoindentation and 4-point bending techniques on the substrate of polycrystalline thin films of two typical FCC metals (Al and Cu), and make concrete theoretical conjectures, based on intuition built from previous theoretical and experimental efforts in micropillar compression and nanoindentation. Based on a wide set of observations over the last decade, we put forward two distinct hypotheses that we propose to investigate in both theory and experiments: Our first conjecture is that crystal plasticity in the central region of micron-sized grains has micropillar-like stochastic features: power-law plastic strain jumps at stresses above the macroscale yield strength, displaying strong size and rate effects. We will demonstrate this similarity in spherical nanoindentation experiments in the central-region of multi-orientation grains of Al and Cu thin films. Al and Cu are selected for their disparity in stacking fault energy and consequently, their different propensity for cross-slip relaxation; however, our protocol may be applied to any crystalline material of technological interest. We will test our hypothesis by performing two-dimensional extended discrete dislocation plasticity (2.5D-DDP) simulations, inspired by comparable successful studies of micropillar plasticity, and extended to model nanoindentation with two slip systems and on a surface of a bicrystal with microhard grain-boundaries (GB), ie. not allowing dislocation absorption (116). Our model will include effective three dimensional dislocation mechanisms such as dislocation multiplication and double-cross-slip assisted glide. Second, we hypothesize that the application of uniform in-plane stress on our thin films below the yield point can smoothen the micrograin plastic response during nanoindentation. On a technological level, we propose that indentation-induced localization (sink-in) may be diminished by the application of concurrent in-plane stress that activates slow, viscoplastic relaxations near GBs. We aim to demonstrate our hypothesis through a 4-point bending apparatus that introduces a homogeneous in-plane stress state before indentation. We will perform simulations of a coarse-grained mesoscale theory of plasticity in a system with microhard GBs, benchmarked through 2.5D-DDP simulations, which will capture the effects of slow viscoplastic relaxations. Our nanoindentation abrupt event statistics studies, either in the micrograin interior or near GBs, will be correlated to direct observations of induced surface dislocation microstructures. For we will use TEM-based methods (PACOM/TKD) in combination with EBSD. Indents placed in the center of grains will be analyzed based on the orientation of the grain, while those near to GBs will be analyzed based on the orientation of each grain, the distance from the GB and the 5 degrees of freedom of the GB.

36 MATERIALS SCIENCE↗

Three-dimensional evaluation of the compression and recovery behavior in a flexible graphite sheet by synchrotron radiation microtomography

The compression and unloading behavior of flexible graphite sheets was investigated using synchrotron radiation microtomography with 1 {mu}m voxel size. The recovery ratio of the flexible graphite sheet was measured accurately by in-situ observation. The three-dimensional strain distribution in the interior of the specimen was obtained using the microstructural tracking method. The inner strain distribution with micrometer scale indicated inhomogeneous deformation. The microstructural tracking analysis revealed that deformation units exist in the flexible graphite sheet. The units seem to deform, affecting the neighboring units with each other. The units had a similar size and shape with compacted exfoliated graphite worms that constitute the flexible graphite sheet. Microscopic deformations during compression and unloading are surely affected by the microstructure of the sheet. Highlights: Black-Right-Pointing-Pointer The compression and recovery behavior was investigated using microtomography. Black-Right-Pointing-Pointer The tracking analysis revealed that deformation units exist in the specimen. Black-Right-Pointing-Pointer Each unit deforms in relation to the neighboring unit.

36 MATERIALS SCIENCE↗

SUBWAVELENGTH RESOLUTION IMAGING OF THE SOLAR DEEP INTERIOR

We derive expectations for signatures in the measured travel times of waves that interact with thermal anomalies and jets. A series of numerical experiments that involve the dynamic linear evolution of an acoustic wave field in a solarlike stratified spherical shell in the presence of fully three-dimensional time-stationary perturbations are performed. The imprints of these interactions are observed as shifts in wave travel times, which are extracted from these data through methods of time-distance helioseismology (Duvall et al.). In situations where at least one of the spatial dimensions of the scatterer was smaller than a wavelength, oscillatory time shift signals were recovered from the analyses, pointing directly to a means of resolving subwavelength features. As evidence for this claim, we present analyses of simulations with spatially localized jets and sound-speed perturbations. We analyze one year's worth solar observations to estimate the noise level associated with the time differences. Based on theoretical estimates, Fresnel zone time shifts associated with the (possible) sharp rotation gradient at the base of the convection zone are on the order of 0.01-0.1 s, well below the noise level that could be reached with the currently available amount of data ({approx}0.15 - 0.2 s with 10 yr of data)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Effect of the V{sub As}V{sub Ga} complex defect doping on properties of the semi-insulating GaAs

The different position V{sub As}V{sub Ga} cluster defect doping in semi-insulating (SI) GaAs has been studied by first-principles calculation based on hybrid density functional theory. Our calculated results show that EL6 level is formed due to the V{sub As}V{sub Ga} complex defect, which is very close to the experimental result. It provides the explanation of the absorption of laser with the wavelength beyond in semi-insulating GaAs. The formation energy of V{sub As}V{sub Ga} complex defect is found to decrease from surface to interior gradually. The conduction band minima and valence band maxima of GaAs (001) surface with the V{sub As}V{sub Ga} complex defect are all located at Γ point, and some defect levels are produced in the forbidden band. In contrast, the conduction band minima and valence band maxima of GaAs with the interior V{sub As}V{sub Ga} complex defect are not located at the same k-point, so it might involve the change of momentum in the electron transition process. The research will help strengthen the understanding of photoelectronic properties and effectively guide the preparation of the SI-GaAs materials.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Time scale for point-defect equilibration in nanostructures

Molecular dynamics simulations of high-temperature annealing are performed on nanostructured materials enabling direct observation of vacancy emission from planar defects (i.e., grain boundaries and free surfaces) to populate the initially vacancy-free grain interiors on a subnanosecond time scale. We demonstrate a universal time-length scale correlation that governs these re-equilibration processes, suggesting that nanostructures are particularly stable against perturbations in their point-defect concentrations, caused for example by particle irradiation or temperature fluctuations.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Harmonic analysis for the characterization and correction of geometric distortion in MRI

Purpose: Magnetic resonance imaging (MRI) is gaining widespread use in radiation therapy planning, patient setup verification, and real-time guidance of radiation delivery. Successful implementation of these technologies relies on the development of simple and efficient methods to characterize and monitor the geometric distortions arising due to system imperfections and gradient nonlinearities. To this end, the authors present the theory and validation of a novel harmonic approach to the quantification of system-related distortions in MRI. Methods: The theory of spatial encoding in MRI is applied to demonstrate that the 3D distortion vector field (DVF) is given by the solution of a second-order boundary value problem (BVP). This BVP is comprised of Laplace’s equation and a limited measurement of the distortion on the boundary of a specified region of interest (ROI). An analytical series expansion solving this BVP within a spherical ROI is obtained, and a statistical uncertainty analysis is performed to determine how random errors in the boundary measurements propagate to the ROI interior. This series expansion is then evaluated to obtain volumetric DVF mappings that are compared to reference data obtained on a 3 T full-body scanner. This validation is performed within two spheres of 20 cm diameter (one centered at the scanner origin and the other offset +3 cm along each of the transverse directions). Initially, a high-order mapping requiring measurements at 5810 boundary points is used. Then, after exploring the impact of the boundary sampling density and the effect of series truncation, a reduced-order mapping requiring measurements at 302 boundary points is evaluated. Results: The volumetric DVF mappings obtained from the harmonic analysis are in good agreement with the reference data. Following distortion correction using the high-order mapping, the authors estimate a reduction in the mean distortion magnitude from 0.86 to 0.42 mm and from 0.93 to 0.39 mm within the central and offset ROIs, respectively. In addition, the fraction of points with a distortion magnitude greater than 1 mm is reduced from 35.6% to 2.8% and from 40.4% to 1.5%, respectively. Similarly, following correction using the reduced-order mapping, the mean distortion magnitude reduces to 0.45–0.42 mm within the central and offset ROIs, and the fraction of points with a distortion magnitude greater than 1 mm is reduced to 2.8% and 1.5%, respectively. Conclusions: A novel harmonic approach to the characterization of system-related distortions in MRI is presented. This method permits a complete and accurate mapping of the DVF within a specified ROI using a limited measurement of the distortion on the ROI boundary. This technique eliminates the requirement to exhaustively sample the DVF at a dense 3D array of points, thereby permitting the design of simple, inexpensive phantoms that may incorporate additional modules for auxiliary quality assurance objectives.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Network Algorithms for Detection of Radiation Sources

In support of national defense, Domestic Nuclear Detection Office’s (DNDO) Intelligent Radiation Sensor Systems (IRSS) program supported the development of networks of radiation counters for detecting, localizing and identifying low-level, hazardous radiation sources. Industry teams developed the first generation of such networks with tens of counters, and demonstrated several of their capabilities in indoor and outdoor characterization tests. Subsequently, these test measurements have been used in algorithm replays using various sub-networks of counters. Test measurements combined with algorithm outputs are used to extract Key Measurements and Benchmark (KMB) datasets. We present two selective analyses of these datasets: (a) a notional border monitoring scenario that highlights the benefits of a network of counters compared to individual detectors, and (b) new insights into the Sequential Probability Ratio Test (SPRT) detection method, which lead to its adaptations for improved detection. Using KMB datasets from an outdoor test, we construct a notional border monitoring scenario, wherein twelve 2”*2” NaI detectors are deployed on the periphery of 21*21meter square region. A Cs-137 (175 uCi) source is moved across this region, starting several meters from outside and finally moving away. The measurements from individual counters and the network were processed using replays of a particle filter algorithm developed under IRSS program. The algorithm outputs from KMB datasets clearly illustrate the benefits of combining measurements from all networked counters: the source was detected before it entered the region, during its trajectory inside, and until it moved several meters away. When individual counters are used for detection, the source was detected for much shorter durations, and sometimes was missed in the interior region. The application of SPRT for detecting radiation sources requires choosing the detection threshold, which in turn requires a source strength estimate, typically specified as a multiplier of the background radiation level. A judicious selection of this source multiplier is essential to achieve optimal detection probability at a specified false alarm rate. Typically, this threshold is chosen from the Receiver Operating Characteristic (ROC) by varying the source multiplier estimate. ROC is expected to have a monotonically increasing profile between the detection probability and false alarm rate. We derived ROCs for multiple indoor tests using KMB datasets, which revealed an unexpected loop shape: as the multiplier increases, detection probability and false alarm rate both increase until a limit, and then both contract. Consequently, two detection probabilities correspond to the same false alarm rate, and the higher is achieved at a lower multiplier, which is the desired operating point. Using the Chebyshev’s inequality we analytically confirm this shape. Then, we present two improved network-SPRT methods by (a) using the threshold off-set as a weighting factor for the binary decisions from individual detectors in a weighted majority voting fusion rule, and (b) applying a composite SPRT derived using measurements from all counters.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

In-situ synchrotron X-ray micro-diffraction investigation of ultra-low-strain deformation microstructure in laminated Ti-Al composites

An ultra-low-strain deformation microstructure was revealed for the first time non-destructively in the bulk interior of an annealed laminated Ti-Al composite-in the "fully recrystallized" Al layer-by a synchrotron-based micro-diffraction technique, namely differential aperture X-ray microscopy (DAXM), through real space mapping with a very high angular resolution (0.01 degrees). This ultra-low-strain deformation microstructure was found to result from the thermal stress, induced during cooling after annealing, due to the different coefficients of thermal expansion for the Ti and Al layers. The annealed sample was further tensile deformed to a strain of 1.66% and followed by in situ DAXM and analyzed by various misorientation mapping methods. The results pointed to the important effects of the initial microstructure and the interface constraint, as well as the grain size and crystal orientation, on the plastic deformation. A gradient in dislocation density from the layer interface to the center was found in the Al layer of the annealed sample, and this gradient increased slightly during tensile deformation. The variation of the dislocation density was further discussed based on the activation and interaction of dislocations in grains of different sizes and orientations during plastic deformation. The findings of this study provided valuable insights in understanding the constraint effect of the laminated metal composite and the design of novel composite materials. (c) 2020 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Crystallographic orientation↗

Thermal Analysis Of Saltstone Disposal Units

SRR requested that SRNL develop a two-dimensional computer simulation model to be capable of predicting grout temperatures attained in Saltstone Disposal Units (SDUs) during the transient addition of saltstone grout and its subsequent storage period. A simulation model was developed to calculate the transient grout temperatures of the SDU facility by taking an axisymmetric and two-dimensional Computational Fluid Dynamics (CFD) approach. The final performance calculations were based on the conduction and radiation model without a convection cooling mechanism for conservative estimate of the grout temperatures and computational efficiency. While convection within the SDU is disabled in the current calculations, the simulation model has the capability of turning convection back on if desired by the user. Hence, the thermal model in its current configuration is best characterized as a finite-volume heat transfer model. However, given that the model can account for convection if desired by the user, it will be referred to as a CFD model. The grout material contains a transient heat source due to the exothermic hydration reactions of the cementitious material mixed with salt solution. The model can predict the transient temperatures at point locations within the poured grout and the overlying vapor space, and at the interior and exterior surfaces of the structure. The thermal model has been developed for two SDUs at the Savannah River Site (SRS); namely, SDU 2A and SDU 6. SDU 2A is a cylindrical unit measuring 150 feet (ft) in diameter, 22 ft tall, and holds approximately three million gallons of grout. SDU 6 is 375 ft in diameter and 43 ft high with a capacity of over thirty million gallons. Prior to performing the thermal calculations for the SDU 6 facility, the benchmarking test for the smaller SDU 2A unit was performed to establish the solution method and to verify the computational results using existing thermocouple data. Based on the Lagrangian discrete method and boundary conditions established by the SDU 2A benchmarking test, the CFD calculations were performed to predict the transient temperatures at local positions of the poured grout and air spaces within the SDU 6 structure.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

SU-F-T-336: A Quick Auto-Planning (QAP) Method for Patient Intensity Modulated Radiotherapy (IMRT)

Purpose: The aim of this study is to develop a quick auto-planning system that permits fast patient IMRT planning with conformal dose to the target without manual field alignment and time-consuming dose distribution optimization. Methods: The planning target volume (PTV) of the source and the target patient were projected to the iso-center plane in certain beameye- view directions to derive the 2D projected shapes. Assuming the target interior was isotropic for each beam direction boundary analysis under polar coordinate was performed to map the source shape boundary to the target shape boundary to derive the source-to-target shape mapping function. The derived shape mapping function was used to morph the source beam aperture to the target beam aperture over all segments in each beam direction. The target beam weights were re-calculated to deliver the same dose to the reference point (iso-center) as the source beam did in the source plan. The approach was tested on two rectum patients (one source patient and one target patient). Results: The IMRT planning time by QAP was 5 seconds on a laptop computer. The dose volume histograms and the dose distribution showed the target patient had the similar PTV dose coverage and OAR dose sparing with the source patient. Conclusion: The QAP system can instantly and automatically finish the IMRT planning without dose optimization.

60 APPLIED LIFE SCIENCES↗

RADIATIVE HYDRODYNAMIC SIMULATIONS OF HD209458b: TEMPORAL VARIABILITY

We present a new approach for simulating the atmospheric dynamics of the close-in giant planet HD209458b that allows for the decoupling of radiative and thermal energies, direct stellar heating of the interior, and the solution of the full three-dimensional Navier-Stokes equations. Simulations reveal two distinct temperature inversions (increasing temperature with decreasing pressure) at the sub-stellar point due to the combined effects of opacity and dynamical flow structure and exhibit instabilities leading to changing velocities and temperatures on the nightside for a range of viscosities. Imposed on the quasi-static background, temperature variations of up to 15% are seen near the terminators and the location of the coldest spot is seen to vary by more than 20{sup 0}, occasionally appearing west of the anti-solar point. Our new approach introduces four major improvements to our previous methods including simultaneously solving both the thermal energy and radiative equations in both the optical and infrared, incorporating updated opacities, including a more accurate treatment of stellar energy deposition that incorporates the opacity relevant for higher energy stellar photons, and the addition of explicit turbulent viscosity.

79 ASTRONOMY AND ASTROPHYSICS↗

Effect of solvents on morphologies of PbTe nanostructures: Controllable synthesis of hollow and solid PbTe nanocubes by a solvothermal method

We demonstrate a facile solvothermal route to grow hollow and solid PbTe nanocubes. The hollow PbTe nanocubes were successfully achieved when EtOH was used as solvent in the presence of nonionic polymer PEG, while the solid PbTe nanocubes were obtained when EG was used as solvent in the presence of PEG, whilst keeping the other experimental conditions constant. The results indicate that the solvents used in reaction system play a key role to determine the interior structure of PbTe nanocubes. On the basis of the experimental results and analysis, a possible growth mechanism has been discussed in detail for the hollow and solid PbTe nanocubes. - Graphical abstract: A facile solution-phase route has been developed to synthesize hollow and solid PbTe nanocubes. The possible growth mechanism of hollow and solid PbTe nanocubes was discussed in detail. Highlights: Black-Right-Pointing-Pointer A facile controllable route was described for hollow and solid PbTe nanocubes. Black-Right-Pointing-Pointer The hollow PbTe nanocubes were achieved using EtOH as solvent. Black-Right-Pointing-Pointer The solid PbTe nanocubes were obtained using EG as solvent. Black-Right-Pointing-Pointer The solvent played a key role for the formation of hollow and solid PbTe nanocubes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

An accurate, stable and efficient domain-type meshless method for the solution of MHD flow problems

The aim of the present paper is the development of an efficient numerical algorithm for the solution of magnetohydrodynamics flow problems for regular and irregular geometries subject to Dirichlet, Neumann and Robin boundary conditions. Toward this, the meshless point collocation method (MPCM) is used for MHD flow problems in channels with fully insulating or partially insulating and partially conducting walls, having rectangular, circular, elliptical or even arbitrary cross sections. MPC is a truly meshless and computationally efficient method. The maximum principle for the discrete harmonic operator in the meshfree point collocation method has been proven very recently, and the convergence proof for the numerical solution of the Poisson problem with Dirichlet boundary conditions have been attained also. Additionally, in the present work convergence is attained for Neumann and Robin boundary conditions, accordingly. The shape functions are constructed using the Moving Least Squares (MLS) approximation. The refinement procedure with meshless methods is obtained with an easily handled and fully automated manner. We present results for Hartmann number up to 10{sup 5}. The numerical evidences of the proposed meshless method demonstrate the accuracy of the solutions after comparing with the exact solution and the conventional FEM and BEM, for the Dirichlet, Neumann and Robin boundary conditions of interior problems with simple or complex boundaries.

97 MATHEMATICS AND COMPUTING↗

Radiological data consolidation and 3D modeling of a building - 15473

A portion of a building at an industrial facility that conducted monazite sands-processing operations in the 1950's under contract to the Atomic Energy Commission (AEC) became contaminated. Subsequently the U.S. Department of Energy designated the facility for remedial action under the Formerly Used Sites Remedial Action Program (FUSRAP). Remedial investigation, remedial actions and post-remediation surveys have been conducted in portions of the building. Radiological data for the interior of the building were compiled, evaluated and presented in a three dimensional (3-D) model (the model) created by AMEC Foster Wheeler in order to identify areas that meet the Record of Decision (ROD) cleanup criteria, and identity areas that may require remedial action or may require additional investigation due to data gaps. The data from different phases of investigation and remediation cover different portions of the building and in some cases overlap. In addition, the data were collected over a period of more than ten years, for different objectives, and thus the instruments and methods for establishing efficiency were not necessarily consistent. The data consolidation process included determining the relative quality of data points to include in the model and the development of rationale associated with assigning a quality level (i.e. ranking) to each data point. The rationale for ranking data quality included, as the primary determining factors, chronological order of the data (most recent was ranked as more reliable), certainty of the sample locations within the building, and analytical data quality. A 3-D model of the building was created using a laser point cloud scan which was then converted into a 3-D design model. Sample locations were then entered into the model and linked with the analytical database to allow display of the radiological results in the model. The visual model allows both strategic and tactical decisions to be made, depending on the level of detail examined. The evaluation process allowed maximum use of the historical data set, rather than requiring older data to be disregarded, and provided at a minimum a qualitative sense of data quality/confidence in the data. The (authors)process also highlights the importance of collecting high quality data from the very beginning with a consistent locational coordinate system, and the need for a good visualization model in order to assess contaminant locations during remedial action or post-remediation surveys.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

The Physics and Chemistry of Cluster-based Catalyst Systems

In this project we used first principles calculations to investigate the physical and chemical properties of atomic clusters, small clumps of matter containing up to a few hundred atoms. The calculations are based on density functional theory, the most efficient and accurate method available for computing and thereby predicting the properties of molecules, clusters, and solids. An initial focus of our work involved studying the reactivity of small Pd clusters. We demonstrated that H2 molecules readily dissociate on Pd clusters and that multiple dissociations can occur on clusters larger than a few Pd atoms. For example, up to eight H2 molecules will dissociate on Pd13 at room temperature. A second focus of the project was to study the evolution of the electrical behavior of clusters, in particular, the evolution of metallic behavior in clusters of metal atoms. We developed a technique for using the electric dipole polarizability of the clusters – the response of the cluster to an applied electric field -- as a probe of this behavior. By decomposing the polarizability into so-called charge transfer (or metallic) and local (or insulating) contributions, we obtained the remarkable result that the per atom charge transfer contributions in sodium clusters attain the same value as occurs in bulk sodium metal for clusters containing as few as 10 atoms. Our calculated total polarizabilities matched experimentally measured trends essentially perfectly, validating the reliability of the calculations and supporting our conclusion that tiny clusters already display bulk-like metallic character. Similar results were obtained for other metal atom clusters, including potassium, aluminum, and zinc. We discovered that the evolution toward bulk metallic behavior for each of these cluster species is essentially identical, when judged using these polarizability-based descriptors. This suggests a universality in the approach of metal clusters to bulk-like metallicity. This discovery is a major outcome of our project. We also used our polarizability-based metrics to investigate the evolution of the properties of Si and NaCl clusters. These systems are non-metallic in the bulk limit. For Si, we find the behavior of small clusters to be metal-like and we attribute this to bonding arrangements in the clusters that are very different from the open structure of crystalline silicon. As the clusters get larger, the bonding in the cluster interior becomes more and more like that of the bulk material. We expect a transition from metal-like to insulator-like behavior to accompany this change is structure. Our results point to a transition at sizes beyond 146 atoms, the largest size treated in our study. We hope to study this transition further in the future. A third thrust of our project involved work on a new approach to eliminating unphysical electron self-interaction from density functional theory calculations. Two electrons exert repulsive forces on each other, but a single electron should not interact with itself. Because of approximations made in density functional theory, individual electrons effectively interact with themselves. The effect of this self-interaction is often small, especially when atoms are near their equilibrium positions in molecules. But the effects can be pronounced when bonds are stretched and also in some situations involving transition metals even when the atoms are near equilibrium. Our research involved the further development of a method for removing self-interaction called the Fermi-Löwdin orbital self-interaction correction or FLO-SIC. We conducted the first systematic FLO-SIC calculations for the individual atoms ranging from Li – Kr. We also carried out a critical comparison of the results of FLO-SIC with an older method known as the Perdew-Zunger self-interaction correction (PZ-SIC). FLO-SIC can be thought of as a modified approach to PZ-SIC that is expected to be computationally more efficient. We demonstrated that the two methods are distinct, but give essentially the same results for quantities such as molecular binding energies or electron removal energies. We are continuing to develop the FLO-SIC methodology with a goal of creating a computationally efficient method that is free of self-interaction effects.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗