Search NASA⌕ Search

SEARCH · Search NASA

Results for “ionic liquid crystal”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

Computational Studies of Structures and Dynamics of 1, 3-Dimethylimidazolim Salt Liquid and their Interfaces Using Polarizable Potential Models

The structures, thermodynamics, dynamical properties of bulk and air/liquid interfaces of three ionic liquids, 1,3-dimethylimidazolium [dmim]+, Cl-, Br-, and I- are studied using molecular dynamics techniques. In bulk melts, the radial distribution functions reveal a significant long-range structural correlation in these ionic liquids. From the angular distribution analysis, the imidazolium rings are found to lie parallel to each other at short distances, consistent with the structures observed in the crystal state. The single-ion dynamics are studied via mean-square-displacements, velocity and orientational correlation functions. The diffusion coefficients and reorientational times are found to be much smaller than H2O. We also observe that anion size plays an important role in the dynamics of ionic liquids. The computed density profiles of the ionic liquid/vapor interface exhibit oscillatory behavior, indicative of surface layering at the interface. Further analysis reveals that the [dmim]+ ions show preferred orientation at the interface with the ring parallel to the surface and methyl group attached to the ring pointing into the vapor phase. The computed surface tensions indicated small differences between these ionic liquids and are inline with recent experimental measurements. The calculated potential drops of these ionic liquids are found to be small and negative. These results could imply that the cation dipoles are likely to orient in the plane that parallel to the surface normal axis. This work was supported by the U.S. Department of Energy's (DOE) Office of Basic Energy Sciences, Chemical Sciences program. The Pacific Northwest National Laboratory is operated by Battelle for DOE.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Factors Defining the Intercalation Electrochemistry of CaFe 2 O 4 -Type Manganese Oxides

Oxides with the CaFe 2 O 4 -type structure have been predicted as being suitable hosts for reactions of intercalation of light cations such as Li and Mg because of their favorable cationic diffusion. Although Li has been shown to intercalate into the Mn 2 O 4 variant, the key structure property correlations determining function are not fully ascertained. This basic information is needed before attempting the intercalation of divalent cations, which face comparably higher migration barriers. For this purpose, here the electrode function of CaFe 2 O 4 -type Li 0.8 Mn 2 O 4 was compared for materials made by a direct high-pressure route or through cation exchange from NaMn 2 O 4 . X-ray diffraction and absorption spectroscopy revealed that, despite having largely the same bulk structure, the presence of surface defects blocked Li + transfer in Li 0.8 Mn 2 O 4 made at high pressure. These defects were not present in the cation-exchanged material, which resulted in highly reversible Li intercalation with very fast kinetics in micrometric crystals. Delithiated electrodes from the cation-exchange synthesis were subsequently reduced in an ionic liquid electrolyte containing Mg 2+ . The process induced topotactic changes in the bulk, strongly suggesting the existence of intercalation, but it is accompanied by severe reactivity with the electrolyte that impedes reversibility. This study uncovers that defects affect the fundamentals of cation intercalation in this novel class of materials. The ability of the cation-exchanged material to conduct fast reactions with Li is consistent with calculated activation energy barriers and creates promise for their use as Mg hosts, provided that novel electrolytes enhanced stability at high potential can be realized.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Ionothermal Synthesis of Tetranuclear Borate Clusters Containing f - and p -Block Metals

The reactions of simple oxides or halides of trivalent lanthanides and actinides or bismuth with boric acid in the ionic liquid 1-butyl-3-methylimidazolium chloride at 150 °C result in the formation and crystallization of a series of isomorphous tetranuclear borate clusters with the general formula M 4 B 22 O 36 (OH) 6 (H 2 O) 13 (M = La, Ce, Pr, Nd, Sm, Eu, Gd, Pu, and Bi). These clusters do not assemble with trivalent cations smaller than Gd 3+ , suggesting that the formation of the clusters is dictated by the size of the metal ion. The cations are found in cavities along the periphery of a cage assembled from the corner- and edge-sharing interactions of BO 3 triangles and BO 4 tetrahedra, yielding a complex chiral cluster. Both enantiomers cocrystallize. The metal ions are nonacoordinate, and their geometries are best described as distorted tridiminished icosahedra. This coordination environment is new for both Pu 3+ and Bi 3+ . Finally, in addition to detailed structural information, UV/vis–NIR absorption and photoluminescence spectra are also provided.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Structure Control of a π-Conjugated Oligothiophene-Based Liquid Crystal for Enhanced Mixed Ion/Electron Transport Characteristics

Developing soft materials with both ion and electron transport functionalities is of broad interest for energy-storage and bioelectronics applications. Rational design of these materials requires a fundamental understanding of interactions between ion and electron conducting blocks along with the correlation between the microstructure and the conduction characteristics. Here, we investigate the structure and mixed ionic/electronic conduction in thin films of a liquid crystal (LC) 4T/PEO4, which consists of an electronically conducting quarterthiophene (4T) block terminated at both ends by ionically conducting oligoethylenoxide (PEO4) blocks. Using a combined experimental and simulation approach, 4T/PEO4 is shown to self-assemble into smectic, ordered, or disordered phases upon blending the materials with the ionic dopant bis(trifluoromethane)sulfonimide lithium (LiTFSI) under different LiTFSI concentrations. Interestingly, at intermediate LiTFSI concentration, ordered 4T/PEO4 exhibits an electronic conductivity as high as 3.1 × 10 –3 S/cm upon being infiltrated with vapor of the 2,3,5,6-tetrafluoro-7,7,8,8-tetracyanoquinodimethane (F4TCNQ) molecular dopant while still maintaining its ionic conducting functionality. This electronic conductivity is superior by an order of magnitude to the previously reported electronic conductivity of vapor co-deposited 4T/F4TCNQ blends. Furthermore, our findings demonstrate that structure and electronic transport in mixed conduction materials could be modulated by the presence of the ion transporting component and will have important implications for other more complex mixed ionic/electronic conductors.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Controlled Design of Phase- and Size-Tunable Monodisperse Ni 2 P Nanoparticles in a Phosphonium-Based Ionic Liquid through Response Surface Methodology

Nanoparticles of nickel phosphide are finding wide ranging utility as catalysts for hydrodesulfurization, hydrogen evolution reaction, and hydrodeoxygenation of bio-oils. Herein, we present a methodology to tailor monodisperse nickel phosphide nanoparticles in terms of size and phase through the use of a statistical response surface methodology. Colloidal nickel phosphide nanoparticles were synthesized by replacing octadecene (ODE), a commonly used organic solvent, by a more sustainable phosphonium-based ionic liquid (IL). The replacement of ODE with the phosphonium-based IL resulted in faster crystallization at lower temperatures to yield phase-pure, monodisperse Ni2P nanoparticles. Using a first-order design, the PPh3/Ni precursor ratio was identified as the most critical factor influencing the resulting size and phase of the nanoparticles. Optimization using a Doehlert matrix for second-order design yielded a second-degree polynomial equation used to predict the mean diameter of the nanoparticles (over a range of 4-12 nm) as a function of the PPh3/Ni precursor ratio and the temperature used during synthesis. The resulting model was validated by performing reactions using randomly chosen sets of conditions; the experimentally determined nanoparticle sizes were in excellent agreement with the theoretical sizes predicted by our model. This demonstrates the utility of a multivariate experimental design as a powerful tool in the development of synthetic strategies toward the preparation of colloidal nanoparticles with highly controlled size, size distribution, and phase.

36 MATERIALS SCIENCE↗

Ion Dissociation Dynamics in an Aqueous Premelting Layer

Using molecular dynamics simulations and methods of importance sampling, we study the thermodynamics and dynamics of sodium chloride in the aqueous premelting layer formed spontaneously at the interface between ice and its vapor. We uncover a hierarchy of time scales that characterize the relaxation dynamics of this system, spanning the picoseconds of ionic motion to the tens or hundreds of nanoseconds associated with fluctuations of the liquid-crystal interface in their presence. We find that ions distort both local interfaces, incurring restoring forces that result in the ions preferentially residing in the middle of the layer. While ion pair dissociation is thermodynamically favorable, these structural and dynamic effects cause its rate to vary by over an order of magnitude through the layer, with a maximum rate significantly depressed from the corresponding bulk value. The solvation environment of ions in the premelting layer is distinct from that in a bulk liquid, being dominated by slow reorganization of water molecules and a water structure intermediate between ice and its melt.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Electrolyte Solvation and Ionic Association: Part IX. Structures and Raman Spectroscopic Characterization of LiFSI Solvates

The bis(fluorosulfonyl)imide anion N(SO 2 F) 2 ⁻ (i.e., FSI⁻) (also referred to as bis(fluorosulfonyl)amide (i.e., FSA-) and imidodi(sulphuryl fluoride)) has attracted tremendous interest in recent years for its utility in both lithium salts and ionic liquids for battery electrolyte applications. To facilitate the understanding of the characteristics of this anion, crystal structures are reported here for the uncoordinated anion in LiFSI-based solvates with cryptand CRYPT-222 and tetraglyme (G4). These crystalline solvates were analyzed by Raman spectroscopy to aid in assigning the Raman bands to the modes of ion coordination found in liquid electrolytes. These structures, as well as a thorough review of other relevant crystallographic data, provide insights into the rather remarkable properties of the FSI- anion with regard to solvate formation and electrolyte properties.

25 ENERGY STORAGE↗

High Cyclability of Ionic Liquid-Produced TiO2 Nanotube Arrays As an Anode Material for Lithium-Ion Batteries

TiO{sub 2} nanotubes (NTs) are considered as a potential SEI-free anode material for Li-ion batteries to offer enhanced safety. Organic solutions, dominatingly ethylene glycol (EG)-based, have widely been used for synthesizing TiO{sub 2} NTs via anodization because of their ability to generate long tubes and well-aligned structures. However, it has been revealed that the EG-produced NTs are composited with carbonaceous decomposition products of EG, release of which during the tube crystallization process inevitably causes nano-scale porosity and cracks. These microstructural defects significantly deteriorate the NTs charge transport efficiency and mechanical strength/toughness. Here we report using ionic liquids (ILs) to anodize titanium to grow low-defect TiO{sub 2} NTs by reducing the electrolyte decomposition rate (less IR drop due to higher electrical conductivity) as well as the chance of the decomposition products mixing into the TiO{sub 2} matrix (organic cations repelled away). Promising electrochemical results have been achieved when using the IL-produced TiO{sub 2} NTs as an anode for Li-ion batteries. The ILNTs demonstrated excellent capacity retention without microstructural damage for nearly 1200 cycles of charge-discharge, while the NTs grown in a conventional EG solution totally pulverized in cycling, resulting in significant capacity fade.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Tunneling and Transport in Nanowires

The goal of this program was to study new physical phenomena that might be relevant to the performance of conductive devices and circuits of the smallest realizable feature sizes possible using physical rather than biological techniques. Although the initial scientific work supported involved the use of scanning tunneling microscopy and spectroscopy to ascertain the statistics of the energy level distribution of randomly sized and randomly shaped quantum dots, or nano-crystals, the main focus was on the investigation of selected properties, including superconductivity, of conducting and superconducting nanowires prepared using electron-beam-lithography. We discovered a magnetic-field-restoration of superconductivity in out-of-equilibrium nanowires driven resistive by current. This phenomenon was explained by the existence of a state in which dissipation coexisted with nonvanishing superconducting order. We also produced ultra-small superconducting loops to study a predicted anomalous fluxoid quantization, but instead, found a magnetic-field-dependent, high-resistance state, rather than superconductivity. Finally, we developed a simple and controllable nanowire in an induced charged layer near the surface of a masked single-crystal insulator, SrTiO 3 . The layer was induced using an electric double layer transistor employing an ionic liquid (IL). The transport properties of the induced nanowire resembled those of collective electronic transport through an array of quantum dots.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Small nickel nanoparticle arrays from long chain imidazolium ionic liquids

A series of six long chain alkyl mono- and bi-cationic imidazolium based salts with bis(trifluoromethylsulfonyl)imide (NTf 2– ) as the anion were synthesized and characterized. Single crystal structure of 1-methyl-3-octadecylimidazolium bis(trifluoromethylsulfonyl)imide could be obtained by X-ray analysis. All these long chain alkyl imidazolium based ILs were applied in the synthesis of nickel nanoparticles via chemical decomposition of an organometallic precursor of nickel. In these media, spontaneous decomposition of Ni(COD) 2 (COD = 1,5-cyclooctadiene) in the absence of H 2 occurred giving small NPs (≤4 nm) with narrow size distributions. Interestingly, formation of regularly interspaced NP arrays was also observed in long chain ILs. Lastly, such array formation could be interesting for potential applications such as carbon nanotube growth.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Deep neural network for the dielectric response of insulators

In this work, we introduce a deep neural network to model in a symmetry preserving way the environmental dependence of the centers of the electronic charge. The model learns from ab initio density functional theory, wherein the electronic centers are uniquely assigned by the maximally localized Wannier functions. When combined with the deep potential model of the atomic potential energy surface, the scheme predicts the dielectric response of insulators for trajectories inaccessible to direct ab initio simulation. The scheme is nonperturbative and can capture the response of a mutating chemical environment. We demonstrate the approach by calculating the infrared spectra of liquid water at standard conditions, and of ice under extreme pressure, when it transforms from a molecular to an ionic crystal.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Cold sintering process of Li 1.5 Al 0.5 Ge 1.5 (PO 4 ) 3 solid electrolyte

Abstract The recently developed technique of cold sintering process (CSP) enables densification of ceramics at low temperatures, i.e., <300°C. CSP employs a transient aqueous solvent to enable liquid phase‐assisted densification through mediating the dissolution‐precipitation process under a uniaxial applied pressure. Using CSP in this study, 80% dense Li 1.5 Al 0.5 Ge 1.5 (PO 4 ) 3 (LAGP) electrolytes were obtained at 120°C in 20 minutes. After a 5 minute belt furnace treatment at 650°C, 50°C above the crystallization onset, Li‐ion conductivity was 5.4 × 10 −5 S/cm at 25°C. Another route to high ionic conductivities ~10 −4 S/cm at 25°C is through a composite LAGP ‐ (PVDF‐HFP) co‐sintered system that was soaked in a liquid electrolyte. After soaking 95, 90, 80, 70, and 60 vol% LAGP in 1 M LiPF 6 EC‐DMC (50:50 vol%) at 25°C, Li‐ion conductivities were 1.0 × 10 −4 S/cm at 25°C with 5 to 10 wt% liquid electrolyte. This paper focuses on the microstructural development and impedance contributions within solid electrolytes processed by (i) Crystallization of bulk glasses, (ii) CSP of ceramics, and (iii) CSP of ceramic‐polymer composites. CSP may offer a new route to enable multilayer battery technology by avoiding the detrimental effects of high temperature heat treatments.

Berbano, Seth S.↗

Understanding the impact of ionic liquid pretreatment on eucalyptus

The development of cost-competitive biofuels necessitates the realization of advanced biomass pretreatment technologies. Ionic liquids provide a basis for one of the most promising pretreatment technologies and are known to allow effective processing of cellulose and some biomass species. Here, we demonstrate that the ionic liquid 1-ethyl-3-methyl imidazolium acetate, [C2mim][OAc], induces structural changes at the molecular level in the cell wall of Eucalyptus globulus. Deacetylation of xylan, acetylation of the lignin units, selective removal of guaiacyl units (increasing the syringyl:guaiacyl ratio) and decreased {beta}-ether content were the most prominent changes observed. Scanning electron microscopy images of the plant cell wall sections reveal extensive swelling during [C2mim][OAc] pretreatment. X-ray diffraction measurements indicate a change in cellulose crystal structure from cellulose I to cellulose II after [C2mim][OAc] pretreatment. Enzymatic saccharification of the pretreated material produced increased sugar yields and improved hydrolysis kinetics after [C2mim][OAc] pretreatment. These results provide new insight into the mechanism of ionic liquid pretreatment and reaffirm that this approach may be promising for the production of cellulosic biofuels from woody biomass.

09 BIOMASS FUELS↗

A small signal amplifier based on ionic liquid gated black phosphorous field effect transistor

In this article we report an analog small signal amplifier based on semiconducting black phosphorus (BP), the most recent addition to the family of two dimensional crystals. The amplifier, consisting of a BP load resistor and a BP field effect transistor (FET) was integrated on a single flake. The gain of the amplifier was found to be ~9 and it remained undistorted for input signal frequencies up to 15 kHz. In addition, we also report record high ON current of 200 µA/µm at V DD = -0.5V in BP FETs. Our results demonstrates the possibility for the implementation of BP in the future generations of analog devices.

36 MATERIALS SCIENCE↗

Sampling Polymorphs of Ionic Solids using Random Superlattices

Polymorphism offers rich and virtually unexplored space for discovering novel functional materials. To harness this potential approaches capable of both exploring the space of polymorphs and assessing their realizability are needed. Here, one such approach devised for partially ionic solids is presented. The structure prediction part is carried out by performing local density functional theory relaxations on a large set of random supperlattices (RSLs) with atoms distributed randomly over different planes in a way that favors cation-anion coordination. Applying the RSL sampling on MgO, ZnO, and SnO 2 reveals that the resulting probability of occurrence of a given structure offers a measure of its realizability explaining fully the experimentally observed, metastable polymorphs in these three systems.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Recovery of Zr from ZrCl 4 by Electrolysis in Fused Salts and Ionic Liquids: Literature Review and Test Plan

This report reviewed the current status on the research and development of Zr electrodeposition in high temperature molten salts and room temperature ionic liquids from ZrCl 4 , which is the product of the chlorination process developed for recycling the Zr claddings of the spent nuclear fuels. Due to the pyrophoricity issue, the Zr metal product from the electrodeposition process is desired to be of coarse, dense crystalline or plates (instead of powder or loose, fine crystals) that are not to be easily oxidized. The findings based on the literature review are included in the report.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Methyl quantum tunneling in ionic liquid [DMIm][TFSI] facilitated by Bis(trifluoromethane)sulfonimide lithium salt

Here, we probe, for the first time, quantum tunneling in the methyl groups of the ionic liquid [DMIm][TFSI] facilitated by the presence of Bis(trifluoromethane)sulfonimide lithium salt. The observation of tunneling is made possible by crystallization, rather than vitrification, of [DMIm][TFSI] at low temperature. Neutron scattering measurements detect quantum tunneling excitations at ~27 μeV at temperatures below 30 K in the presence of LiTFSI at a concentration of 1 mol/kg, but not in salt-free [DMIm][TFSI]. This indicates that the methyl rotational potential barrier is reduced by the presence of LiTFSI, thus bringing the tunneling excitations into the measurable range. The salt-induced reduction of the rotational barrier is corroborated by quasi-elastic scattering data associated with stochastic re-orientation of methyl groups measured between 40 and 60 K.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗