Search NASA⌕ Search

SEARCH · Search NASA

Results for “kinetic impact”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Toward control co-design of utility-scale wind turbines: Collective vs. individual blade pitch control

A large-eddy simulation framework has been coupled with controller modules to systematically investigate the impacts of collective (CPC) and individual (IPC) pitch control strategies on utility-scale wind turbine energy production and fatigue loads. Wind turbine components were parameterized using an actuator surface model to simulate the rotor blades and the turbine nacelle. The baseline CPC and IPC algorithms, consisting of single-input single-output proportional–integral controllers and two integral controllers, respectively, were incorporated into the numerical framework. A series of simulations were carried out to investigate the relative performance of the two controllers under various turbulent inflow conditions, spanning hub-height velocities of 7 to 14 m/s. The numerical simulation results of this study showed that, in comparison to the CPC, the IPC controller could successfully reduce the damage equivalent loads of utility-scale turbines at regions 2 and 3 of turbine operation by about 3% and 40%, respectively, without any penalty on the power production of the turbine. It was also shown that, despite its minor impact on the turbulence kinetic energy of the wake, the IPC controller did not influence the recovery of the turbine wake.

17 WIND ENERGY↗
DOE OSTI2020

Sooting tendencies of 20 bio-derived fuels for advanced spark-ignition engines

The sooting tendencies of 20 bio-derived fuels indicated as potential blendstocks for spark-ignition engines by the Co-Optimization of Fuels & Engines (Co-Optima) Initiative are studied. The Yield Sooting Index (YSI) is used to quantify the sooting tendencies. The Co-Optima Chemical Model is used to predict the numerical YSIs for all test fuels, and these results are compared with measurements. Experimental YSIs are newly measured for 2 furans and are taken from our previous work for the other compounds. Overall, the predicted YSIs agree well with measurements, within the experimental uncertainties, except for 2,5-dimethylfuran (2,5-DMF). It is found that Polycyclic Aromatic Hydrocarbons (PAH) growth reactions have little influence on the relative soot production from each fuel and therefore on YSI predictions. A modified sensitivity coefficient formulation is proposed to evaluate reaction sensitivities specifically for YSI. This formulation is applied to the 2,5-DMF-doped flame, and six 2,5-DMF initial decomposition reactions, which lead to different major soot precursors, are identified as the most sensitive reactions. The impact of the chemical kinetic uncertainties embedded in these reactions is quantified by randomly perturbing their reaction rates within a factor of two. The resulting prediction uncertainty in the 2,5-DMF-doped flame is found to be ± 8 YSI units (±11%), which demonstrates that the test-fuel-specific decomposition reactions indeed have considerable influence on its YSI prediction. Our research suggests that more accurate kinetic parameters for fuel initial decomposition reactions can potentially improve YSI predictions effectively, without altering the YSI predictions of other fuels with significantly different molecular structures.

09 BIOMASS FUELS↗
DOE OSTI2025

Impacts of Focused Ion Beam Processing on the Fabrication of Nanoscale Functionalized Probes

Herein, we examine the impact of Ga + ion kinetic energy and the target material type on the extent of ion implantation and structural damage in atomic force microscopy probes made of Al 2 O 3 and ZnO manufactured by focused ion beam (FIB) using scanning transmission electron microscopy and energy-dispersive X-ray mapping. Penetration of Ga into the Al 2 O 3 lattice induced structural distortions and amorphization. For ZnO probes, Ga is uniformly dispersed across the surface, resulting in the formation of distinct clusters. Atom probe tomography further validates the Ga distributions in Al 2 O 3 and ZnO nanoprobes. Complementary Monte Carlo simulations with the transport of ions in the matter program indicated that the introduction of Ga + prompts the generation of cation and anion vacancies, an occurrence more pronounced in Al 2 O 3 compared to ZnO. In conclusion, this study not only enriches the knowledge of ion-matter interactions, but also serves as a practical guide for the fabrication of nanoscale functionalized AFM probes.

Al2O3↗
DOE OSTI2021

Modeling Volatility-Based Aerosol Phase State Predictions in the Amazon Rainforest

Organic aerosol (OA) is a complex matrix of various constituents—fresh (primary organic aerosols—POA) and aged via oxidation (secondary organic aerosols—SOA), generated from biogenic, anthropogenic, and biomass burning sources. The viscosity of OA can be critical in influencing new particle formation, reactive uptake processes that impact evaporation-growth kinetics, and the lifetime of particles in the atmosphere. We report this work utilizes a well-defined relationship between volatility and viscosity for pure compounds, which we incorporated within the Weather Research and Forecasting Model coupled to chemistry (WRF-Chem) to simulate the phase state and viscosity of bulk OA during the dry-to-wet transition season (September–October) in the Amazon rainforest during 2014. Our simulations indicate spatial and temporal heterogeneity in aerosol phase state often not captured by global-scale models. We show the strong role of water associated with organic aerosol ($w_s$) as the dominant factor that can be used to quantitatively estimate OA viscosity. Analysis of WRF-Chem simulations across the entire atmospheric column indicates a strong inverse log-linear relationship between $w_s$ and OA viscosity with a correlation coefficient approaching 1, in the background and biomass burning-influenced conditions. At high altitudes where relative humidity (RH) and temperatures are low, our simulations indicate that OA exists in a semisolid-/solid-like phase state, consistent with previous studies. OA hygroscopicity is strongly correlated (ca. –0.8) with OA viscosity at RH ca. 30–50%, but this RH range is found mostly at low OA concentrations and the middle troposphere (ca. 6–10 km altitudes) in our simulated domain. OA hygroscopicity is uncorrelated with viscosity at higher-RH (near surface) and lower-RH (upper troposphere) regimes. At the urban site near surface, where day–night differences in RH are significant, RH is found to drive the phase state. At the background forested site near surface, where day–night RH differences are small, biomass burning-influenced OA is semisolid and a significant OA associated with background conditions is liquid-like. Simulations indicate a long tail of OA viscosity frequency distributions extending in the semisolid/solid regimes over background biogenic-influenced conditions due to the role of low-volatility OA components such as monoterpene oxidation products.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Insights into interfacial effect and local lithium-ion transport in polycrystalline cathodes of solid-state batteries

Interfacial issues commonly exist in solid-state batteries, and the microstructural complexity combines with the chemical heterogeneity to govern the local interfacial chemistry. The conventional wisdom suggests that “point-to-point” ion diffusion at the interface determines the ion transport kinetics. Here, we show that solid-solid ion transport kinetics are not only impacted by the physical interfacial contact but are also closely associated with the interior local environments within polycrystalline particles. In spite of the initial discrete interfacial contact, solid-state batteries may still display homogeneous lithium-ion transportation owing to the chemical potential force to achieve an ionic-electronic equilibrium. Nevertheless, once the interior local environment within secondary particle is disrupted upon cycling, it triggers charge distribution from homogeneity to heterogeneity and leads to fast capacity fading. Our work highlights the importance of interior local environment within polycrystalline particles for electrochemical reactions in solid-state batteries and provides crucial insights into underlying mechanism in interfacial transport.

25 ENERGY STORAGE↗
DOE OSTI2022

Impact of hydronium ions on the Pd-catalyzed furfural hydrogenation

Abstract In aqueous mediums, the chemical environment for catalytic reactions is not only comprised of water molecules but also of corresponding ionized species, i.e., hydronium ions, which can impact the mechanism and kinetics of a reaction. Here we show that in aqueous-phase hydrogenation of furfural on Pd/C, increasing the hydronium ion activities by five orders of magnitude (from pH 7 to pH 1.6) leads to an increase of less than one order of magnitude in the reaction rate. Instead of a proton-coupled electron transfer pathway, our results show that a Langmuir-Hinshelwood mechanism describes the rate-limiting hydrogen addition step, where hydrogen atom adsorbed on Pd is transferred to the carbonyl C atom of the reactant. As such, the strength of hydrogen binding on Pd, which decreases with increasing hydronium ion concentration (i.e., 2 kJ mol H2 −1 per unit pH), is a decisive factor in hydrogenation kinetics (rate constant +270%). In comparison, furfural adsorption on Pd is pH-independent, maintaining a tilted geometry that favors hydrogen attack at the carbonyl group over the furan ring.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Dissolution kinetics of a sodium borosilicate glass in Tris buffer solutions: impact of Tris concentration and acid (HCl/HNO 3 ) identity

Here, understanding the corrosion behavior of glasses in near-neutral environments is crucial for many technologies including glasses for regenerative medicine and nuclear waste immobilization. To maintain consistent pH values throughout experiments in the pH = 7 to 9 regime, buffer solutions containing tris(hydroxymethyl)aminomethane (“Tris”, or sometimes called THAM) are recommended in ISO standards 10993-14 and 23317 for evaluating biomaterial degradation and utilized throughout glass dissolution behavior literature—a key advantage being the absence of dissolved alkali/alkaline earth cations (i.e. Na + or Ca 2+ ) that can convolute experimental results due to solution feedback effects. Although Tris is effective at maintaining the solution pH, it has presented concerns due to the adverse artificial effects it produces while studying glass corrosion, especially in borosilicate glasses. Therefore, many open questions still remain on the topic of borosilicate glass interaction with Tris-based solutions. We have approached this topic by studying the dissolution behavior of a sodium borosilicate glass in a wide range of Tris-based solutions at 65 °C with varied acid identity (Tris–HCl vs. Tris–HNO 3 ), buffer concentration (0.01 M to 0.5 M), and pH (7–9). The results have been discussed in reference to previous studies on this topic and the following conclusions have been made: (i) acid identity in Tris-based solutions does not exhibit a significant impact on the dissolution behavior of borosilicate glasses, (ii) ~0.1 M Tris-based solutions are ideal for maintaining solution pH in the absence of obvious undesirable solution chemistry effects, and (iii) Tris–boron complexes can form in solution as a result of glass dissolution processes. The complex formation, however, exhibits a distinct temperature-dependence, and requires further study to uncover the precise mechanisms by which Tris-based solutions impact borosilicate glass dissolution behavior.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Kinetic processes of phase separation and aggregation behaviors in slot-die processed high efficiency Y6-based organic solar cells

Morphological optimization has proved to be one crucial factor contributing to the 19% efficiency of Y6-based organic solar cells (OSCs). Although the relationship between component miscibility and film morphology has been established, it has not been clarified how the film formation processes proceed, especially for methods compatible with large-area fabrication, i.e. slot-die coating, which restricts the further optimization of the morphology. Herein, we comprehensively investigate the effect of miscibility and the film-formation kinetic process on film morphology during processing with different solvents. A highest power conversion efficiency (PCE) of 17.38% can be obtained in a D18:Y6 device processed with slot-die coating in an open-air environment. However, due to their relatively poor miscibility, incorporating a trace amount of chlorobenzene (CB) into CF can sufficiently promote Y6 aggregation, leading to increased phase separation and thus the average PCE drops to 15.16%. In contrast, a PM6:Y6 blend shows insensitive changes in the kinetic process as well as the final morphology, and thus in the comparable PCEs when cast with different solvents, which is ascribed to their relatively good miscibility. As a result, this work provides scientific guidelines for device optimization by combining the intermediate gap from miscibility to kinetic process and their impact on final morphology.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Phases of dark matter from inverse decays

Inverse decays are an interesting avenue for producing dark matter in the early Universe. We study in detail various phases of dark matter parameter space where inverse decays control its abundance, expanding on our work of inverse decay (INDY) dark matter and going beyond. The role of initial conditions and the impact of departure from kinetic equilibrium are investigated as well. We show how these inverse decay phases can arise in theories of a kinetically mixed dark photon and dark Higgs, with promising prospects for detection at upcoming experiments.

Cosmology↗
DOE OSTI2024

Energy Principles of Scientific Breakeven in an Inertial Fusion Experiment

Fusion “scientific breakeven” (i.e., unity target gain G target , total fusion energy out > laser energy input) has been achieved for the first time (here, G target ∼ 1.5 ). This Letter reports on the physics principles of the design changes that led to the first controlled fusion experiment, using laser indirect drive, on the National Ignition Facility to produce target gain greater than unity and exceeded the previously obtained conditions needed for ignition by the Lawson criterion. Key elements of the success came from reducing “coast time” (the time duration between the end of the laser pulse and implosion peak compression) and maximizing the internal energy delivered to the “hot spot” (the yield producing part of the fusion fuel). The link between coast time and maximally efficient conversion of kinetic energy into internal energy is explained. The energetics consequences of asymmetry and hydrodynamic-induced mixing were part of high-yield big radius implosion design experimental and design strategy. Herein, it is shown how asymmetry and mixing consolidate into one key relationship. It is shown that mixing distills into a kinetic energy cost similar to the impact of implosion asymmetry, shifting the threshold for ignition to higher implosion kinetic energy—a factor not normally included in most statements of the generalized Lawson criterion, but the key needed modifications clearly emerge. Published by the American Physical Society 2024

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Initial Assessment of TeF 6 Adsorption

Research and development that supports the management of off-gases from nuclear fuel reprocessing has historically been focused on the off-gas streams that arise from aqueous reprocessing technology. However, as Gen-IV reactor development pathways move toward deployment, alternative spent nuclear fuel (SNF) processing and disposition pathways have been considered more actively. This work is focused upon aspects of fluoride volatility (FV) processing. The versatility of this method for deployment against multiple types of spent fuel encourages the continued advancement of both the primary separations processes and the secondary processes, including waste treatment, material control and accountability, and engineering designs. Recent work noted that TeF 6 , the most highly volatile fluorinated compound produced during FV processing, did not have a clear abatement technology recommended in the literature. Thus, this work performed scoping tests on activated alumina and copper shot to assess whether they could be used to remove TeF 6 from gas streams that bear F 2 . Previous work on this topic was not well described in the literature and was not performed with excess F 2 in the stream as would be typical of spent fuel processing via FV. To support an understanding of the concentration of TeF 6 contacting the adsorbent beds, a series of preliminary testing identified the TeF 6 production rate and the equilibrium concentration of TeF 6 in the gas stream contacting the adsorbent. Excess F 2 was determined to not affect the ability of activated alumina to remove TeF 6 from the gas stream quickly and completely. A determination of whether excess F 2 affected the distribution depth of Te in the sorbent bed is still pending analysis of the used sorbent. Literature suggests that when activated alumina is near saturation, TeF 6 could migrate from the sorbent bed. Future testing should investigate this possibility. Copper metal did not adsorb TeF 6 in the presence of F 2 across the sorbent temperature range of 50 to 335°C. F 2 was fully removed by the copper bed. Although preliminary thermodynamics would indicate adsorption to be energetically favorable, other factors that impact adsorption (e.g., slow kinetics, excess fluorine on the copper surface, an unfavorable transition state) are likely preventing the adsorption of TeF 6 at an easily measurable rate. The work also investigated TeF 6 production from multiple forms of Te in the temperature range of 100 to 250°C. No previous study had assessed the initial reaction rates for this process. A carefully designed study allowed determination of the activation energy for the production of TeF 6 from Te metal. The substantial amount of data collected during this study merits analysis beyond what is described here. A more in-depth kinetic analysis will be pursued. Additional analytical results will provide the ability to benchmark adsorption coefficients for TeF 6 , understand the distribution of TeF 6 within the alumina bed, and better understand the effect of F 2 partial pressure on Te fluorination. The data from this report, as supplemented by these additional analyses, will be submitted to a peer-reviewed journal.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Developing machine-learning potentials to study properties of the tritium formation and diffusivity in pure and defective Zircaloy-4 getters

Objective of this work was to study the formation of Sn impurity and hydride phases in Zr and study their impacts on the diffusion kinetics of 3 H by using DFT based ML approach. By implementing deep neural potential (DNP) technique, we developed potential for Zr-H and Sn impurity systems and validated the DNP by using DFT results. We found that by implementing machine learning approach, it is possible to achieve accuracy comparable to DFT level for the more realistic models by using less computational time and resources.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Understanding the effect of crystal anisotropy on grain growth, texturing and transport via the orthorhombic ?-U system [Slides]

The alpha phase of uranium exhibits the orthorhombic crystal structure, resulting in significant physical property anisotropy. These complex properties make the material challenging to work with in engineering settings but provide a rich arena to investigate the fundamental, multi-scale effects of anisotropy on physical behaviors such as grain growth and microstructure evolution under irradiation. We apply molecular dynamics and phase field modeling to study mass transport and grain growth in alpha-uranium. We characterize the mobilities of crystalline defects and the interfacial energy, and We find that the grain boundary energy is highly variable depending on the interface structure and that the relative rates of defect transport change with temperature. We also find that anisotropic thermal expansion has a significant impact on grain growth kinetics and texture development. Our results are used to explain experimental observations and to provide a basis for further hypotheses into the complex physical behavior of alpha-uranium.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

An Electrochemical Electrode to Detect Theophylline Based on Copper Oxide Nanoparticles Composited with Graphene Oxide

The electrochemical analysis of theophylline (THP) was investigated by fabricating a carbon paste electrode (CPE) modified with graphene oxide (GO) along with copper oxide (CuO) nanoparticles (CuO-GO/CPE). The impact of electro-kinetic parameters such as the heterogeneous rate constant, the scan rate, the accumulation time, the pH, the transfer coefficient, and the number of electrons and protons transferred into the electro-oxidation mechanism of THP has been studied utilizing electrochemical methods such as cyclic voltammetry (CV) and differential pulse voltammetry (DPV). The differential pulse voltammetry technique was employed to investigate THP in pharmaceutical and biological samples, confirming the limit of detection (LOD) and quantification (LOQ) of the THP. X-ray diffraction (XRD) and scanning electron microscopy (SEM) analysis were performed to characterize the CuO nanoparticles. The CuO-GO/CPE was more sensitive in THP detection because its electrocatalytic characteristics displayed an enhanced peak current in the 0.2 M supporting electrolyte of pH 6.0, proving the excellent sensing functioning of the modified electrode.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Oxidation kinetic modelling of Fe-based oxygen carriers for chemical looping applications: Impact of the topochemical effect

Chemical looping is a promising technology for fossil fuel utilization due to its high fuel conversion efficiency with in-situ CO 2 capture capability. Metal oxide are used as oxygen carriers (OCs) and circulate between a fuel reactor and an air reactor to perform reduction and oxidation reactions, respectively. In general, OC exiting the fuel reactor is not reduced fully to its metallic state due to many factors including carbon deposition and OC deactivation. Therefore, the effect of the initial reduction state on the OC oxidation in the air reactor is a significant parameter for consideration in developing the oxidation kinetic model. The objective of this work is to develop a physically significant kinetic model that applies to the oxidation of both initially fully and partially reduced OC with air. For this study, 1.5 mm Fe-based OC particle supported with TiO 2 was used as the model OC particle due to its complex multistep reaction nature. The oxidation kinetics were experimentally investigated in a thermogravimetric analyzer (TGA). Results indicate a significant difference in the oxidation rate profile for the OCs when oxidized from an initially fully reduced compared to an initially partially reduced state. Elemental mapping via energy-dispersive X-ray spectroscopy (EDS) reveals a shrinking-core type topochemical pattern across the OC particle, which was identified to be the cause of the dependency of kinetics on the initial reduction state. A generalized kinetic model was developed based on the observed shrinking-core behavior without presuming any rate-determining steps and experimentally validated over a broad range of temperatures (800–1000 °C) and oxygen concentrations (5, 7, 10, and 15 mol%). Impacts of particle porosity, size, and core-shell structure on the OC oxidation kinetics were analyzed in the developed oxidation kinetic model to suggest methods of improving the oxidation rate of the OC without modifying the chemical composition.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Modeling the Impact of the Organic Aerosol Phase State on Multiphase OH Reactive Uptake Kinetics and the Resultant Heterogeneous Oxidation Timescale of Organic Aerosol in the Amazon Rainforest

Accurate predictions of chemical lifetime, i.e., oxidation timescale and change in the mass of organic aerosols (OAs) in atmospheric models, are critical to quantify the impacts of OA on aerosol–cloud interactions, radiative forcing, and air quality. The heterogeneous oxidation of OA by hydroxyl (OH) radicals is a key process governing OA mass changes during their oxidation. Recently, laboratory observations of the OH uptake coefficient (γ OH ) and heterogeneous reaction rate (k het,OH ) for different OA systems with varying phase states have been combined to develop a new parameterization of γ OH and k het,OH as a function of the OA phase state, i.e., viscosity (η OA ). Here, in this work, we use a recently published viscosity prediction framework to analyze the new γ OH and k het,OH parameterization with a box model. Subsequently, we implement this box model to predict γ OH and k het,OH over the Amazon rainforest in the dry-to-wet transition season with both significant biomass burning and biogenic influences. Relevant parameters within our box model are specified based on detailed regional model simulations over the Amazon using the Weather Research and Forecasting model coupled with Chemistry (WRF-Chem). η OA is predicted as a function of species volatility, OA composition (including water uptake) along with ambient relative humidity (RH), and temperature. Based on ambient conditions simulated by WRF-Chem over the entire atmospheric column, we use the box model to predict the upper bounds of the heterogeneous oxidation timescale of OA. Based on previous laboratory measurements, we assume that this heterogeneous OH oxidation causes fragmentation (carbon loss) of OA, followed by the evaporation of the fragmented molecules that results in the exponential decay of OA. We predict that the oxidation timescale of OA is ~1 month near the Earth’s surface in the pristine Amazonian background because of low OH concentrations. But OA is oxidized more rapidly within urban and wildfire plumes near the Earth’s surface with an order of magnitude higher OH concentrations compared to the pristine background, causing the simulated oxidation timescale of OA to be much shorter, ~3–4 days. At 3–5 km altitudes where biomass burning OA is predicted to be semisolid, the heterogeneous oxidation timescale is estimated as ~6 days to 3 weeks and decreases with increasing OH concentrations within plumes. We show that the simulated mass loss of OA is strongly size-dependent, where smaller particles oxidize more rapidly compared to larger particles due to their greater per-particle surface area-to-volume ratio. Increasing urbanization and deforestation in the Amazon in the future might increase OH concentrations in the background Amazon, causing faster oxidation of OA. At higher altitudes above liquid clouds, especially in the upper troposphere where temperatures approach ~250 K, future measurements are needed to reduce the uncertainties related to the mass loss of OA at colder temperatures and low relative humidity conditions due to its heterogeneous OH oxidation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Progress in modeling hydrogen assisted ammonia oxidation with new experiments and a further reconciliation of the NH 3 + OH rate constant

Hydrogen-assisted oxidation of ammonia in a premixed, laminar flow tubular reactor under reducing conditions was investigated experimentally and through chemical kinetic modeling. Due to its impact on the competition for OH among ammonia and hydrogen, the rate constant for NH 3 + OH (R1) was determined through state-of-the-art theoretical kinetics calculations, employing composite energies that include the effects of higher order electronic excitations on the electronic energies along the variational reaction path and treating the limitations in the kinetics posed by the passage through a hydrogen-bonded complex. The resulting rate constant was in close agreement with the recent experimental value from Zaczek et al. (2025), settling a long-term dispute about the high-temperature value of k 1 and confirming within 20% the value previously used in modeling. The chemical kinetic model, with no other changes, captured well measured concentrations of NH 3 , H 2 , NO, and N 2 O from flow reactor oxidation of NH 3 /H 2 at slightly reducing conditions over a range of temperature (900-1350 K) and NH 3 /H 2 ratios (0.5-2.0). Comparison of the present results with reported data from a non-premixed setup indicates that for laminar flow tubular reactors, the reactor configuration may have implications for the observed H 2 consumption due to the possibility of preferential oxidation during mixing.

Ab initio theory↗