Search NASA⌕ Search

SEARCH · Search NASA

Results for “lateral force”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Hypersonic aerothermal characteristics of a manned low finenes ratio shuttle booster

An investigation of a winged booster model having canards and an ascent configuration comprised of the booster mounted in tandem with an orbiter model has been conducted at Mach 10.2 in the continuous flow hypersonic tunnel. Longitudinal and lateral directional force characteristics were obtained over angle of attack ranges of -12 deg to 60 deg for the booster and -11 deg to 11 deg for the ascent configuration. Interference heating effects on the booster using the phase-change coating technique were determined at 0 deg angle of attack. Some oil flow photographs of the isolated booster and orbiter and ascent configuration are also presented.

Bernot, P. T.↗
NASA NTRS1973

Nondestructive shell-stability estimation by a combined-loading technique.

The variation of specimen lateral stiffness with compressive axial loading is studied experimentally, and it is demonstrated that buckling loads can be predicted for monocoque shells from such data. A study of the initial specimen geometry is presented, and an evaluation is made of its effect on the distribution of stiffness at zero axial load. When the lateral test force used to determine the stiffness is considered as a destabilizing load in combination with the axial compression, it is shown that critical values of the force can be estimated by the 'Southwell plot' procedure. These critical forces can be correlated with axial load and extrapolated to yield an accurate estimate of the buckling load.

Craig, J. I.↗
NASA NTRS1975

Wind tunnel tests of an 0.019-scale space shuttle integrated vehicle -2A configuration (model 14-OTS) in the NASA Ames 8 by 7 foot unitary wind tunnel (IA12C), volume 1

The purpose of the test was to determine the effects of cold jet gas plumes on (1) the integrated vehicle longitudinal and lateral-directional force data, (2) exposed wing hinge moment, (3) wing pressure distributions, (4) orbiter MPS external pressure distributions, and (5) model base pressure. The similarity between solid and gaseous plumes was investigated, and fluorescent oil flow visualization studies were conducted.

Hardin, R. B.↗
NASA NTRS1975

Wind tunnel tests of an 0.019-scale space shuttle integrated vehicle -2A configuration (model 14-OTS) in the NASA Ames 8 X 7 foot unitary wind tunnel, volume 2

The purpose of the test was to determine the effects of cold jet gas plumes on (1) the integrated vehicle longitudinal and lateral-directional force data, (2) exposed wing hinge moment, (3) wing pressure distributions, (4) orbiter MPS external pressure distributions, and (5) model base pressures. An investigation was undertaken to determine the similarity between solid and gaseous plumes; fluorescent oil flow visualization studies were also conducted. Plotted wing pressure data is tabulated.

Hardin, R. B.↗
NASA NTRS1975

Wind tunnel tests of an 0.019-scale space shuttle integrated vehicle -2A configuration (model 14-OTS) in the NASA Ames 8 X 7 foot unitary wind tunnel, volume 3

Tests were conducted to determine the effects of cold jet gas plumes on (1) the integrated vehicle longitudinal and lateral-directional force data, (2) exposed wing hinge moment, (3) wing pressure distributions, (4) orbiter MPS external pressure distributions, and (5) model base pressures. An investigation was undertaken to determine the similarity between solid and gaseous plumes; fluorescent oil flow visualization studies were also conducted. Tabulated data listings are included.

Hardin, R. B.↗
NASA NTRS1978

Characterization of the non axial thrust generated by large solid propellant rocket motors in three axis stabilized ascent

Nonaxial thrusts produced by solid rocket motors during three-axis stabilized attitude control have been determined from ascent experience on twenty three Burner II, Burner IIA and Block 5D-1 upper stage vehicles. A data base representing four different rocket motor designs (three spherical and one extended spherical) totaling twenty five three-axis stabilized firings is generated. Solid rocket motor time-varying resultant and lateral side force vector magnitudes, directions and total impulses, and roll torque couple magnitudes, directions, and total impulses are tabulated in the appendix. Population means and three sigma deviations are plotted. Existing applicable ground test side force and roll torque magnitudes and total impulses are evaluated and compared to the above experience data base. Within the spherical motor population, the selected AEDC ground test data consistently underestimated experienced motor side forces, roll torques and total impulses. Within the extended spherical motor population, the selected AEDC test data predicted experienced motor side forces, roll torques, and total impulses, with surprising accuracy considering the very small size of the test and experience populations.

Kosmann, W. J.↗
NASA NTRS1980

Rolling flow wind tunnel tests of F-18 aircraft

The lateral directional characteristics of an F-18 aircraft was investigated. Aerodynamic derivatives associated with pure roll rate, or the 'p' derivatives were obtained. The model is described and the procedures used to obtain and correct the data, and a graphical presentation of the results are presented. These results include graphs of the lateral directional static stability derivatives versus angle of attack, and the lateral directional force and moment coefficients versus nondimensional roll rate. Results are presented for several configurations including complete, complete without vertical tails, complete without horizontal tails, fuselage wing and fuselage alone. Each of these configuations was tested with and without wing leading edge extensions. The basic control surfaces were deflected and the results were investigated.

Lutze, F. H.↗
NASA NTRS1989

High angle-of-attack aerodynamic characteristics of crescent and elliptic wings

Static longitudinal and lateral-directional forces and moments were measured for elliptic- and crescent-wing models at high angles-of-attack in the NASA Langley 14 by 22-Ft Subsonic Tunnel. The forces and moments were obtained for an angle-of-attack range including stall and post-stall conditions at a Reynolds number based on the average wing chord of about 1.8 million. Flow-visualization photographs using a mixture of oil and titanium-dioxide were also taken for several incidence angles. The force and moment data and the flow-visualization results indicated that the crescent wing model with its highly swept tips produced much better high angle-of-attack aerodynamic characteristics than the elliptic model. Leading-edge separation-induced vortex flow over the highly swept tips of the crescent wing is thought to produce this improved behavior at high angles-of-attack. The unique planform design could result in safer and more efficient low-speed airplanes.

Vandam, C. P.↗
NASA NTRS1989

High-alpha aerodynamic characteristics of crescent and elliptic wings

Static longitudinal and lateral-directional forces and moments were measured for elliptic- and crescent-wing models at high angles of attack in the NASA Langley 14-by-22-ft Subsonic Tunnel. The forces and moments were obtained for an angle-of-attack range including stall and post-stall conditions at a Reynolds number based on the average wing chord of about 1.8 million. Flow-visualization photographs using a mixture of oil and titanium-dioxide were also taken for several incidence angles. The force and moment data and the flow-visualization results indicated that the crescent wing model with its highly swept tips produced much better high-angle-of-attack aerodynamic characteristics than the elliptic model. Leading-edge separation-induced vortex flow over the highly swept tips of the crescent wing is thought to produce this improved behavior at high angles of attack. The unique planform design could result in safer and more efficient low-speed airplanes.

Van Dam, C. P.↗
NASA NTRS1989

Research and development activities at the Goddard Space Flight Center for the flight telerobotic servicer project

The Flight Telerobotic Servicer (FTS) is being developed by the Goddard Space Flight Center (GSFC) for performing a variety of assembly, servicing, inspection and maintenance tasks on the Space Station. The Project Office at GSFC has tasked the Engineering Directorate to assemble a robotics research and development program which will support the FTS project. The activities center around support for the Development Test Flight (DTF) on the Space Shuttle and investigations of operational problems associated with the FTS on Space Station Freedom. For the DTF, areas such as control algorithms, safety systems, and end-effectors will be developed. For FTS operations, the emphasis will be to develop a dual-arm bi-lateral force-reflecting teleoperator and use it as an FTS Operational Simulator (FTSOS). The simulator will be used to investigate operational techniques, camera configurations, operator interfacing, orbital replacement unit (ORU) designs, end-effector designs, and training techniques. After a series of test activities, reports will be generated for input to the DTF and FTS designs.

Ollendorf, Stanford↗
NASA NTRS1991

Computational optimization of a pneumatic forebody flow control concept

The effectiveness of a tangential slot blowing concept for generating lateral control forces on an aircraft forebody is analyzed using computational fluid dynamics. The flow about a fighter forebody is computed using a multiple-zone, thin-layer Navier-Stokes code. Tangential slot blowing is modeled by the use of an actuator plane. The effects of slot location and slot length on the efficiency of the system are analyzed. Results of the study indicate that placement of the slot near the nose of the aircraft greatly enhances the efficiency of the system, while the length and circumferential location of the slot are of secondary importance. Efficiency is defined by the amount of side force or yawing moment obtained per unit blowing coefficient. The effect of sideslip on the system is also analyzed. The system is able to generate incremental changes in forces and moments in flows with sideslip angles up to 10 deg comparable to those obtained at zero sideslip. These results are used to determine a baseline configuration for an experimental study of the tangential slot blowing concept.

Gee, Ken↗
NASA NTRS1992

Computational investigation of slot blowing for fuselage forebody flow control

This paper presents a computational investigation of a tangential slot blowing concept for generating lateral control forces on an aircraft fuselage forebody. The effects of varying both the jet width and jet exit velocity for a fixed location slot are analyzed. This work is aimed at aiding researchers in designing future experimental and computational models of tangential slot blowing. The primary influence on the resulting side force of the forebody is seen to be the jet mass flow rate. This influence is sensitive to different combinations of slot widths and jet velocities over the range of variables considered. Both an actuator plane and an overset grid technique are used to model the tangential slot. The overset method successfully resolves the details of the actual slot geometry, extending the generality of the numerical method. The actuator plane concept predicts side forces similar to those produced by resolving the actual slot geometry.

Murman, Scott M.↗
NASA NTRS1933

Pressure Distribution Tests on a Series of Clark Y Biplane Cellules with Special Reference to Stability

The pressure distribution data discussed in this report represents the results of part of an investigation conducted on the factors affecting the aerodynamic safety of airplanes. The present tests were made on semispan, circular-tipped Clark Y airfoil models mounted in the conventional manner on a separation plane. Pressure readings were made simultaneously at all test orifices at each of 20 angles of attack between -8 degrees and +90 degrees. The results of the tests on each wing arrangement are compared on the bases of maximum normal force coefficient, lateral stability at a low rate of roll, and relative longitudinal stability. Tabular data are also presented giving the center of pressure location of each wing.

Noyes, Richard W↗
NASA NTRS1994

Aerodynamic surface distension system for high angle of attack forebody vortex control

A deployable system is introduced for assisting flight control under certain flight conditions, such as at high angles of attack, whereby two inflatable membranes are located on the forebody portion of an aircraft on opposite sides thereof. The members form control surfaces for effecting lateral control forces if one is inflated and longitudinal control forces if both are inflated.

Zell, Peter T.↗
NASA NTRS1999

STS-99 Crew Interviews: Kevin R. Kregel

Live footage of a preflight interview with Mission Commander Kevin R. Kregel is seen. The interview addresses many different questions including why Kregel became an astronaut, the events that led to his interest, his career path through the Air Force and later the Navy, and then finally, his selection by NASA as an astronaut. Other interesting information that this one-on-one interview discusses is the purpose for the Shuttle Radar Topography Mission (SRTM), with specific focus placed on why this SRTM flight is important, and what we will learn from the 3D topographic map of the Earth. The two antennas that will be taking the pictures, the involvement of the National Imagery and Mapping Agency (NIMA), EARTHCAM, a student-controlled camera on the Endeavour Orbiter, and Kregel's responsibility during this 24 hour mission are also discussed.

Source record↗
NASA NTRS1999

Comparison of CFD Predictions of the TCA Baseline

The computational fluid dynamics (CFD) comparisons being presented are compared to each other and to wind tunnel (WT) data on the baseline TCA. Some of the CFD computations were done prior to the tests and others later. Only force data (CL vs CD) from CFD will be presented as part of this report. The WT data presented comes from the testing of the baseline TCA in the Langley Unitary Plan Wind Tunnel (UPWT), Test Section #2. There are 2 sets of wind tunnel data being presented: one from test 1671 of model 2a (flapped wing) and the other from test 1679 of model 2b (solid wing). Most of the plots show only one run from each of the WT tests per configuration. But many repeat runs were taken during the tests. The WT repeat runs showed an uncertainty in the drag of +/- 0.5 count. There were times when the uncertainty in drag was better, +/- 0.25 count. Test 1671 data was of forces and pressures measured from model 2a. The wing had cutouts for installing various leading and trailing edge flaps at lower Mach numbers. The internal duct of the nacelles are not designed and fabricated as defined in the outer mold lines (OML) iges file. The internal duct was fabricated such that a linear transition occurs from the inlet to exhaust. Whereas, the iges definition has a constant area internal duct that quickly transitions from the inlet to exhaust cross sectional shape. The nacelle internal duct was fabricated, the way described, to save time and money. The variation in the cross sectional area is less than 1% from the iges definition. The nacelles were also installed with and without fairings. Fairings are defined as the build up of the nacelles on the upper wing surface so that the nacelles poke through the upper surface as defined in the OML iges file. Test 1679 data was of forces measured from model 2a and 2b. The wing for model 2b was a solid wing. The nacelles were built the same way as for model 2a, except for the nacelle base pressure installation. The nacelles were only tested with the fairings for model 2a and 2b during test 1679.

Cappuccio, Gelsomina↗
NASA NTRS2001

A Regional Model Study of Synoptic Features Over West Africa

Synoptic weather features over West Africa were studied in simulations by the regional simulation model (RM) at the NASA/Goddard Institute for Space Studies. These pioneering simulations represent the beginning of an effort to adapt regional models for weather and climate prediction over West Africa. The RM uses a cartesian grid with 50 km horizontal resolution and fifteen vertical levels. An ensemble of four simulations was forced with lateral boundary conditions from ECMWF global analyses for the period 8-22 August 1988. The simulated mid-tropospheric circulation includes the skillful development and movement of several African wave disturbances. Wavelet analysis of mid-tropospheric winds detected a dominant periodicity of about 4 days and a secondary periodicity of 5-8 days. Spatial distributions of RM precipitation and precipitation time series were validated against daily rain gauge measurements and ISCCP satellite infrared cloud imagery. The time-space distribution of simulated precipitation was made more realistic by combining the ECMWR initial conditions with a 24-hr spin-up of the moisture field and also by damping high frequency gravity waves by dynamic initialization. Model precipitation "forecasts" over the Central Sahel were correlated with observations for about three days, but reinitializing with observed data on day 5 resulted in a dramatic improvement in the precipitation validation over the remaining 9 days. Results imply that information via the lateral boundary conditions is not always sufficient to minimize departures between simulated and actual precipitation patterns for more than several days. In addition, there was some evidence that the new initialization may increase the simulations' sensitivity to the quality of lateral boundary conditions.

Druyan, Leonard M.↗