Search NASA⌕ Search

SEARCH · Search NASA

Results for “leading indicators”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Investigations of LHW-plasma coupling and current drive at high density related to H-mode experiments in EAST

Two important issues in achieving lower hybrid current drive (LHCD) high confinement plasma in EAST are to improve lower hybrid wave (LHW)-plasma coupling and to drive the plasma current at a high density. Studies in different configurations with different directions of toroidal magnetic field (Bt) show that the density near the antenna is affected by both the radial electric field induced by plasma without a LHW (Er-plasma) in the scrape off layer (SOL), and the radial electric field induced by LHW power (Er-LH) near the grill. Investigations indicate that Er× Btin the SOL leads to a different effect of configuration on the LHW-plasma coupling and Er-LH× Btaccounts for the asymmetric density behaviour in the SOL observed in the experiments, where Eris the total radial electric field in the SOL. Modelling of parametric instability (PI), collisional absorption (CA) and scattering from density fluctuations (SDF) in the edge region, performed considering the parameters of high density LHCD experiments in EAST, has shown that these mechanisms could be responsible for the low current drive (CD) efficiency at high density. Radiofrequency probe spectra, useful for documenting PI occurrence, show sidebands whose amplitude in the case of the lithiated vacuum chamber is smaller than in the case of poor lithiation, consistently with growth rates from PI modeling of the respective reference discharges. Since strong lithiation is also expected to diminish the parasitic effect on the LHCD of the remaining possible mechanisms, this appears to be a useful method for improving LHCD efficiency at a high density.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Laboratory evaluation of cyclic underground hydrogen storage in the Temblor sandstone of the San Joaquin Basin, California

Underground Hydrogen Storage (UHS) in depleted oil and gas reservoirs could provide a cost-effective solution to balance seasonal fluctuations in renewable energy generation. However, data and knowledge on UHS at subsurface conditions are limited so it is difficult to estimate how effective this type of storage could be. In this study, we perform high pressure experiment to measure the effectiveness of cyclic hydrogen (H 2 ) storage in a specimen of Temblor sandstone retrieved from the San Joaquin Basin of California. Our experiment mimics reservoir pressure conditions to measure H 2 -brine relative permeability and fluid-rock interactions over the course of ten charging and discharging cycles. Initial gas breakthrough occurred at 15 % to 25 % H2 saturation in the specimen with 3 % NaCl brine as the resident fluid. Continuing injecting to 4 pore volumes (PV) of H 2 yielded an asymptotic H 2 saturation of 38 % to 41 %, a level often referred to as the irreducible gas saturation based on two-phase flow. The boundary condition in this study mimics the near wellbore region, which experiences bi-directional H 2 flow. This bi-directional flow led to evaporative drying of the specimen resulting in 94 % H 2 saturation at the end of 10th cycle. This indicates that cyclic flow and evaporative drying can lead to more efficient reservoir storage where a larger fraction of the reservoir porosity is usable to store H 2 . The produced gas stream consisted of H 2 mixed with 8 % to 22 % H 2 O, indicating formation dry-out by evaporation. Meanwhile, produced water chemistry indicated calcite and silicate dissolution, with calcite sourced from fossil fragments. This led to a loss of cementation and weakened the rock sample. Combined, our results indicate dry-out, compaction, increased H 2 saturation, rock weakening, and permeability loss during cyclic UHS. Overall, we anticipate that the combined effects should lead to higher than anticipated UHS storage efficiency per volume of sandstone reservoir rock.

08 HYDROGEN↗
DOE OSTI2026

Implications of climate change impacts for emission and land use scenario development

Scenarios of future emissions and land use produced by integrated assessment models have traditionally been developed without accounting for how climate change impacts could affect the emissions and land use trajectories themselves. This omission risks skewing our assessments of the plausible range of future emission pathways and associated Earth system changes. Beyond the salience for emission scenario development, a better integrated representation of human and Earth system changes and feedbacks would enable better anticipation of the implications of alternative socio-economic development pathways. We use the Global Change Analysis Model to investigate whether endogenizing several impacts when generating its baseline emission scenario is warranted. We do so by comparing the emissions and land use change that result from the baseline scenario with and without impacts, where impacts are implemented as exogenous changes to water availability, crop and labor productivity, and energy demand and supply. Our results indicate that the effect on global emissions leads to less than 0.1 °C increase in warming by 2100 and therefore do not support endogenizing impacts. This conclusion is conditional on our modeling framework and the specific impact channels represented but is consistent with other studies that have addressed the magnitude of feedbacks by implementing a two-way coupling. However, we do find regional impacts indicating that local economies and well-being measures may be affected significantly.

climate impacts↗
DOE OSTI2020

Magnetic phase transitions in quantum spin-orbital liquids

Here, we investigate the spin and orbital correlations of a superexchange model with spin $\textit{S}$ = 1 and orbital $\textit{L}$ = 1 relevant for $5d^4$ transition-metal Mott insulators, using exact diagonalization and density matrix renormalization group (DMRG). For spin-orbit coupling λ = 0, the orbitals are in an entangled state that is decoupled from the spins. We find two phases with increasing λ: (I) the $\textit{S}$2 phase with two peaks in the structure factor for λ ≤ λ$_{c1}$ ≈ 0.34$\textit{J}$ where $\textit{J}$ is the ferromagnetic exchange; and, (II) the $\textit{S}$1 phase for λ$_{c1}$ < λ ≤ λ$_{c2}$ ≈ 1.2$\textit{J}$ with emergent antiferromagnetic correlations. Both $\textit{S}$1 and $\textit{S}$2 phases are shown to exhibit power-law correlations, indicative of a gapless spectrum. Upon increasing λ > λ$_{c2}$ leads to a product state of local spin-orbital singlets that exhibit exponential decay of correlations, indicative of a gapped phase. We obtain insights into the phases from the well-known Uimin-Lai-Sutherland model in an external field that provides an approximate description of our model within mean-field theory.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

Shallow soils are warmer under trees and tall shrubs across Arctic and Boreal ecosystems

Soils are warming as air temperatures rise across the Arctic and Boreal region concurrent with the expansion of tall-statured shrubs and trees in the tundra. Changes in vegetation structure and function are expected to alter soil thermal regimes, thereby modifying climate feedbacks related to permafrost thaw and carbon cycling. However, current understanding of vegetation impacts on soil temperature is limited to local or regional scales and lacks the generality necessary to predict soil warming and permafrost stability on a pan-Arctic scale. Here we synthesize shallow soil and air temperature observations with broad spatial and temporal coverage collected across 106 sites representing nine different vegetation types in the permafrost region. We showed ecosystems with tall-statured shrubs and trees (> 40 cm) have warmer shallow soils than those with short-statured tundra vegetation when normalized to a constant air temperature. In tree and tall shrub vegetation types, cooler temperatures in the warm season do not lead to cooler mean annual soil temperature indicating that ground thermal regimes in the cold-season rather than the warm-season are most critical for predicting soil warming in ecosystems underlain by permafrost. Our results suggest that the expansion of tall shrubs and trees into tundra regions can amplify shallow soil warming, and could increase the potential for increased seasonal thaw depth and increase soil carbon cycling rates and lead to increased carbon dioxide loss and further permafrost thaw.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Structural reforms and income distribution: new evidence for OECD countries

Abstract This article examines the impact of labour market and product market reforms on income inequality for 25 OECD countries between 1970 and 2020, using the local projections approach and an updated narrative-based dataset of the reform indicators. Our results suggest that both types of (endogenized) market-oriented reforms increase income inequality, but the effects are small. Consistent with this finding is that counter-reforms lead to less income inequality. Our results also indicate that the inequality-increasing effect of market-oriented reforms is mostly a result of more income going to the top of the income distribution.

Wiese, Rasmus↗
DOE OSTI2020

Synthesis, aphicidal activity and conformation of novel insect kinin analogues as potential eco‐friendly insecticides

Abstract BACKGROUND The discovery of ecofriendly insecticides through a new strategy for aphid control is important because of the substantial resistance and unexpected eco‐toxicity to honeybees caused by traditional insecticides. The insect kinins, a class of multifunctional insect neuropeptides, are considered for potential application in pest control. In our previous work we developed several series of insect kinin analogues and found a promising lead II‐1 with good aphicidal activity. To seek further eco‐friendly aphicides, the optimization of II‐1 is carried out in this study. RESULTS Fifteen novel Yaa 3 modified analogues based on the lead II‐1 were synthesized. The aphicidal tests indicated that IV‐3 , IV‐5 and IV‐10 exhibited significant activity against the soybean aphid Aphis glycines with LC 50 values of 0.0029, 0.0072 and 0.0086 mmol L –1 , respectively, higher than that of lead II‐1 and the commercial Pymetrozine. The molecular modeling results showed that analogues II‐1 , IV‐3 , IV‐5 , IV‐7 and IV‐10 formed a β‐turn‐like conformation, while the conformation of analogues IV‐1 , IV‐2 and IV‐9 seemed to be linear. Some structural elements favorable for the activity were proposed based on the conformation‐activity relationship of the analogues. CONCLUSION Insect kinin analogues derived from lead II‐1 by modifying the hydrolysis site Yaa 3 with natural, sterically hindered α‐ and β‐amino acids showed great potential as eco‐friendly insecticides. Inspiringly, the most active analogue IV‐3 can be a candidate for further development. The β‐turn‐like conformation and the orientation of the aromatic rings of the side chain of Phe 2 and Trp 4 may be critical factors beneficial to activity. © 2019 Society of Chemical Industry

Zhang, Chuanliang↗
DOE OSTI2025

Pressure‐Induced Structural and Optoelectronic Modulations in 2D Dion‐Jacobson Hybrid Lead Iodide Perovskites With a Rigid Spacer

2D hybrid organic-inorganic perovskites (HOIPs) are known for their superior chemical and thermal stability over 3D variants, positioning them as promising materials for advanced optoelectronic applications. Applying external high pressure is an effective strategy to modify their structures and tune their optoelectronic properties. This study examines the high-pressure behavior of a Dion-Jacobson type 2D HOIP, DPDAPbI 4 , which incorporates the rigid organic spacer N,N-dimethylphenylene-p-diammonium (DPDA). Utilizing photoluminescence, UV–visible absorption, vibrational spectroscopy, and in situ synchrotron powder X-ray diffraction, an isostructural phase transition is identified near 1.5 GPa, marked by a notable shift in photoluminescence intensity linked to free exciton emission. Synchrotron X-ray diffraction reveals significant anisotropic compression along the c-axis, while structural analysis indicates the rare phenomenon of reduced lead-iodide octahedral distortion below 2 GPa, contrasting with the increased octahedral distortion reported in most previous studies on lead-based 2D HOIPs. Density functional theory calculations elucidate the structural origins and mechanisms driving the pressure-induced phase transition and optoelectronic tuning. These findings underscore the critical interplay between rigid organic spacers and inorganic octahedra in modulating high-pressure optoelectronic properties, offering valuable insights for designing future 2D HOIPs with tailored functionalities.

14 SOLAR ENERGY↗
DOE OSTI2023

Image Characterization of Reactions Generated by an Aeroengine Micromixing Injector for Lean Direct Injection of Hydrogen and Hydrogen/Natural Gas Blend

An aeroengine micromixing injector, originally designed for lean direct injection of jet fuel, was adapted to work with hydrogen, natural gas, and any blend in between. The ultimate goal of the design was to achieve low NOx emissions when operated on pure hydrogen; to better characterize its performance, flame imaging diagnostics was implemented. Three types of cameras mounted parallel to the injector base and pointing towards the quartz combustor cylinder with the same angle were operated simultaneously: Nikon D90, Dynacolor FB-N9-U, and Phantom v7.1, to capture the visible spectrum, OH* chemiluminescence, and dynamic behavior of the flames, respectively. The current work also includes the overlapping of visible spectrum and OH* chemiluminescence, as an effort to qualitatively define the heat release over the flame area, i.e., UV over visible domain. Additionally, a z-type schlieren configuration was employed to reinforce the presence of some small-scale details occurring near the injector outlet ports. Using the airbox pressure drop, preheat temperature, fuel composition and flame temperature as the factors of study, a Box Behnken model was designed yielding into a 16-points matrix for the operability region, at atmospheric pressure. The main responses were extracted from the OH* images, because of its correlation with the flame heat release, these being the flame area and its average brightness, the heat release area and its center of gravity and leading edge. To assess the importance of the main factors and their interactions, an analysis of variance (ANOVA) was performed for each response, considering as significant each contributor with a p-value below 0.05. For these five responses it was found that all four main factors need to be included into the model (most of them because its own significance, others to ensure the model hierarchy), as well as some common interactions as the preheat and flame temperatures or pressure drop and fuel composition, and quadratic terms from fuel composition or flame temperature. Three of the five models presented R2 and coefficient of variance (C.V.) indicators around 0.97 and 5%, respectively; the leading edge ANOVA yielded into R2=0.78 and C.V.=18.88%; and the heat release area showed R2=0.91 and C.V.=24.13%. Lastly, the confinement ratio effect of the combustor over the flame structure was quantified, for three different conditions: the original 80 mm inner diameter and 200 mm length cylinder was compared against a shorter 150 mm tube (same inner diameter) and a narrower 47 mm inner diameter one (same 200 mm length). The length had a smaller effect than the inner diameter, even though both factors were not strong enough to make a significant deviation on most of the flame parameters: the difference was within the repeatability margin of error for the brightness, flame area, and center of gravity and leading edge of the heat release area.

Imaging diagnostics, flame characterization, OH* c↗
DOE OSTI2020

Superconductivity enhancement in phase-engineered molybdenum carbide/disulfide vertical heterostructures

Stacking layers of atomically thin transition-metal carbides and two-dimensional (2D) semiconducting transition-metal dichalcogenides, could lead to nontrivial superconductivity and other unprecedented phenomena yet to be studied. In this work, superconducting α-phase thin molybdenum carbide flakes were first synthesized, and a subsequent sulfurization treatment induced the formation of vertical heterolayer systems consisting of different phases of molybdenum carbide—ranging from α to γ' and γ phases—in conjunction with molybdenum sulfide layers. These transition-metal carbide/disulfide heterostructures exhibited critical superconducting temperatures as high as 6 K, higher than that of the starting single-phased α-Mo 2 C (4 K). We analyzed possible interface configurations to explain the observed moiré patterns resulting from the vertical heterostacks. Our density-functional theory (DFT) calculations indicate that epitaxial strain and moiré patterns lead to a higher interfacial density of states, which favors superconductivity. Such engineered heterostructures might allow the coupling of superconductivity to the topologically nontrivial surface states featured by transition-metal carbide phases composing these heterostructures potentially leading to unconventional superconductivity. Moreover, we envisage that our approach could also be generalized to other metal carbide and nitride systems that could exhibit high-temperature superconductivity.

heterostructure↗
DOE OSTI2020

The compositional optimization and secondary phases evaluation regarding the creep resistance in Grade 91 steel through the CALPHAD approach

The critical secondary phases along with critical temperatures in regard to the creep resistance of Grade 91 steel alloy were evaluated in order to optimize the composition of the alloy to improve the creep resistance. The critical temperatures which are highlighted in this paper are Ac1 (the threshold temperature in which austinite begins to form), and Ac3 (the threshold temperature at which ferrite is fully transformed into austenite). Furthermore, optimization was presented through various Cr, V, Nb, and N concentrations in Gr.91 in relation to these critical temperatures and the mole fraction of M 23 C 6 , MX, and Z-Phase as critical secondary phases. Here, the results indicate that increasing V and Nb will increase MX stability, whereas decreasing Cr and N lead to a decrease in Z-Phase and M 23 C 6 stability, which may lead to an increased creep resistance of the material. Upon further analyzing the V, Nb, and N concentrations in Gr.91, results indicate that increasing Nb content in the steel can lead to an increased stability of Nb-rich MX2 carbide which can be used to replace Z-Phase in low N steels. Simulation results indicate that elimination of N with a dramatic increase in Nb concentrations result in the stability increase of only M 23 C 6 and MX2 phases at temperature regions between 600 °C and 1370 °C and a complete removal of Z-Phase precipitation. Overall, with the elimination of N, which destabilizes Z-Phase precipitation, and an increase in Nb for NbC carbide stability, a possible solution to increasing both long-term and short-term creep resistance for Gr.91 can be achieved, though further optimization and creep experiments need to be conducted for final conclusions.

36 MATERIALS SCIENCE↗
DOE OSTI2020

The ionic conductivity of Sm‐doped ceria

Abstract The oxygen ion conductivity of polycrystalline samples of Sm‐doped ceria and of Gd‐doped ceria is studied as a function of doping fraction and temperature using impedance spectroscopy allowing the separation of bulk and grain boundary conductivity. The introduction of a fine spacing for the Sm dopant fraction allows the clear identification of the dopant fraction leading to the largest bulk conductivity. At 267°C, the largest bulk conductivity is shown for Ce 0.93 Sm 0.07 O 1.965 . With increasing temperature, indications of an increase in the dopant fraction, which leads to the maximum in conductivity, are found. For the grain boundary conductivity, the maximum appears at larger dopant fractions compared to the bulk conductivity. The largest total conductivity for both dopants is again found for Sm‐doped ceria. In literature, different syntheses and sample preparation methods led to larger total conductivities for Gd‐doped ceria. In this work, we demonstrate that the variation of sintering conditions leads to scattering in the conductivity over one order of magnitude. Finally, we demonstrate that, in nominally pure cerium oxide, impurities dominate the ionic conductivity.

Koettgen, Julius↗
DOE OSTI2021

Ensemble‐Based Assimilation of Satellite All‐Sky Microwave Radiances Improves Intensity and Rainfall Predictions for Hurricane Harvey (2017)

Abstract Ensemble‐based data assimilation of radar observations across inner‐core regions of tropical cyclones (TCs) in tandem with satellite all‐sky infrared (IR) radiances across the TC domain improves TC track and intensity forecasts. This study further investigates potential enhancements in TC track, intensity, and rainfall forecasts via assimilation of all‐sky microwave (MW) radiances using Hurricane Harvey (2017) as an example. Assimilating Global Precipitation Measurement constellation all‐sky MW radiances in addition to GOES‐16 all‐sky IR radiances reduces the forecast errors in the TC track, rapid intensification (RI), and peak intensity compared to assimilating all‐sky IR radiances alone, including a 24‐hr increase in forecast lead‐time for RI. Assimilating all‐sky MW radiances also improves Harvey's hydrometeor fields, which leads to improved forecasts of rainfall after Harvey's landfall. This study indicates that avenues exist for producing more accurate forecasts for TCs using available yet underutilized data, leading to better warnings of and preparedness for TC‐associated hazards in the future.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Effects of temperature inversion on densification in chemical vapor infiltration

In a classical chemical vapor infiltration (CVI) process, the competing effects of chemical kinetics and reagent gas transport lead to non–uniform depositions such that outer layers of a preform densify faster leaving the core highly porous. Currently, CVI must be performed at a sufficiently low temperature to achieve good densification quality which leads to high processing time and cost. Volumetric heating of the preform, especially through microwaves, can create temperature inversion such that the core is hotter than the outer surface and potentially, overcome the challenges associated with isothermal CVI. Direct numerical simulations (DNS) of densification under various such temperature distributions indicate that microwave heating in CVI processing can lead to better (uniform) densification of porous preforms. Here the role of key parameters describing the temperature distributions on the densification behavior is investigated. Strategic temporal control of the temperature distribution shows that processing times can be reduced by almost half while maintaining a good densification quality similar to that of low–temperature isothermal processing. Inside–out densification due to the inverted temperature profile is a key distinguishing characteristic of microwave assisted CVI.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Experimental Study of TCP Throughput Profiles and Dynamics Over Dedicated Connections

A throughput profile expressed as a function of the round-trip times of a data transport infrastructure is a critical indicator of its level of optimization, particularly, over dedicated connections. We study the throughput profiles of eleven TCP versions using measurements collected over dedicated hardware-emulated connections with distances spanning round the earth. Among them, BBR has overall higher temporal variations and lower throughput profiles compared to five loss-based TCP versions, and the comparison with other TCP versions is mixed. Using the Poincare map regions of throughput time traces, we show that the richer dynamics of BBR are correlated with its lower throughput profiles. We present basic analytical results that indicate that higher temporal variations of TCP methods lead to lower throughput profiles, thereby establishing the underlying causality. Under external losses, BBR achieves sustained high throughput compared to others as the loss rate is increased. Overall, our results provide insights into the relationship between time dynamics and throughput profiles of TCP versions, in particular, show that limited time traces can be indicative of global properties of throughput profiles.

Rao, Nageswara↗
DOE OSTI2020

Confronting grand unification with lepton flavour violation, dark matter and LHC data

We explore possible signatures for charged lepton flavour violation (LFV), sparticle discovery at the LHC and dark matter (DM) searches in grand unified theories (GUTs) based on SU(5), flipped SU(5) (FSU(5)) and SU(4) c ×SU(2) L ×SU(2) R (4-2-2). We assume that soft supersymmetry-breaking terms preserve the group symmetry at some high input scale, and focus on the non-universal effects on different matter representations generated by gauge interactions at lower scales, as well as the charged LFV induced in Type-1 see-saw models of neutrino masses. We identify the different mechanisms that control the relic DM density in the various GUT models, and contrast their LFV and LHC signatures. The SU(5) and 4-2-2 models offer good detection prospects both at the LHC and in LFV searches, though with different LSP compositions, and the SU(5) and FSU(5) models offer LFV within the current reach. The 4-2-2 model allows chargino and gluino coannihilations with neutralinos, and the former offer good detection prospects for both the LHC and LFV, while gluino coannihilations lead to lower LFV rates. Our results indicate that LFV is a powerful tool that complements LHC and DM searches, providing significant insights into the sparticle spectra and neutrino mass parameters in different models.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2022

Tuning working potential of silicon-phosphorus anode via microstructure control for high-energy lithium-ion batteries

The primary research on anode materials of lithium-ion batteries have been focused on increasing the specific capacity, while the working potential that is also closely related to the practical energy density of batteries has been paid much less attention. In this paper, starting from micrometer-sized silicon and black phosphorus, we have reported a high-energy silicon-phosphorus/carbon anode (denoted as mSPC) via a high-energy ball milling process, which demonstrates an average discharge working potential of 0.3 volts versus lithium, together with a high reversible capacity of > 2000 mAh/g, high initial coulombic efficiency of 84%, excellent cycle stability, and superior rate capability up to 15 A/g. Furthermore, in situ focused-ion-beam scanning electron microscopy reveals that the volume change of the mSPC anode during repeated (de) lithiation is effectively alleviated. In contrast, starting from nanometer-sized silicon, the resulted anode (denoted as nSPC) not only presents a lower reversible capacity (~1200 mAh/g), but also exhibits a higher charge/discharge working potential, leading to reduced energy density. Our results indicate the importance of composition/structure control in tailoring the working potential and specific capacity of alloying-type anodes towards high-energy lithium-ion batteries.

25 ENERGY STORAGE↗
DOE OSTI2024

Fe-carbide/Fe-oxide-based nanocomposites synthesized as magnetic nanomaterials via laser ablation synthesis in solution (LASiS)

Magnetic nanostructured materials (MNMs) have gained prominence in materials technology developments owing to their potential biomedical applications for hyperthermia cancer treatment, and transplant organ cryopreservation. Herein, we report the facile and cost-effective synthesis of Fe-based composite MNMs, comprising both Fe@Fe 2 O 3 and Fe 3 C@C core-shell nanoparticles (NPs), via Laser Ablation Synthesis in Solution (LASiS) using Fe targets ablated under acetone and toluene. Detailed materials characterizations using electron microscopy-based imaging, diffraction studies, and spectroscopic analyses - including Raman and Mössbauer spectroscopy - relate the structure-composition properties for different Fe-oxide/carbide phases in the aforesaid MNMs to their respective magnetic responses. Specifically, we confirm the presence of ultra-small (2–10 nm) amorphous Fe-oxide NPs, as well as Fe@Fe 2 O 3 core-shell NPs (20–40 nm) in the samples synthesized by ablating Fe under acetone. In contrast, samples synthesized under toluene indicate a higher concentration of Fe 3 C@C core-shell NPs (20–40 nm) with a relatively low concentration of Fe 2 O 3 NPs (2–10 nm). Furthermore, the crystallinity of the metallic phases and carbonaceous shell coatings are systematically increased by carrying out LASiS under heated toluene (up to ~95 °C). Importantly, mössbauer spectroscopy results indicate that the elevation in toluene temperature leads to an increase in the concentrations of Fe 3 C@C NPs from ~40 % to ~53 % (at.).

36 MATERIALS SCIENCE↗