Search NASA⌕ Search

SEARCH · Search NASA

Results for “lithium diffusion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1971

Lithium-doped solar cells for space use

Lithium doped p-n solar cells meet the basic requirements for space use. The efficiencies of the Lopex lithium cells which range from 10.5 to 12.8% are equal to or better than C.G. lithium cell and 10 ohms-cm n-p cell efficiencies. Reduction in the stresses introduced during boron diffusion has eliminated cell size restrictions and both 2 x 2 and 2 x 6 cm lithium doped cells have been fabricated. The Ti-Ag contacts which are tested 100% with a tape peel test, and pull tested and humidity tested on a sample basis are comparable to the Ti-Ag contacts on n-p cells.

Payne, P. A.↗
NASA NTRS1971

Some major results of the Fourth Annual Conference on Effects of Lithium Doping on Silicon Solar Cells

Lithium doped silicon solar cells having dimensions as large as 12 sq cm are now possible, due to significantly improved boron-diffusion techniques. A large increase was observed in the short circuit current measured in tungsten light for cells that were fabricated using the improved diffusion techniques as compared with previous cells, indicating a preservation of minority carrier diffusion length in the base region of the former cells. Sintering of the contacts of lithium doped cells fabricated from Lopex silicon resulted in large increases in maximum power, mostly due to an open circuit voltage improvement, over non-sintered cells. Efficiencies as high as 12.8% were observed, with the average efficiency being about 11.9%.

Berman, P. A.↗
NASA NTRS1980

High temperature storage characteristics of lithium sulfur dioxide cells

Hermetically sealed SO2 cells were developed to eliminate SO2 diffusion and its adverse effects on shelf life. A two part barrier coating material was applied to the internal surface of the glass seal and cured under a predetermined thermal profile in order to prevent the self discharge associated with glass seal corrosion.

Watson, T.↗
NASA NTRS2014

Computational and Experimental Investigation of Li-doped Ionic Liquid Electrolytes: [pyr14][tfsi], [pyr13][fsi], and [EMIM][BF4]

We employ molecular dynamics (MD) simulation and experiment to investigate the structure, thermodynamics, and transport of N-methyl-N-butylpyrrolidinium bis(trifluoromethylsufonyl)imide ([pyr14][TFSI]), N -methyl-N-propylpyrrolidinium bis(fluorosufonyl)imide ([pyr13][FSI]), and 1-ethyl-3-methylimidazolium boron tetrafluoride ([EMIM][BF4]), as a function of Li-salt mole fraction (0.05 xLi+ 0.33) and temperature (298 K T 393 K). Structurally, Li+ is shown to be solvated by three anion neigh- bors in [pyr14][TFSI] and four anion neighbors in both [pyr13][FSI] and [EMIM][BF4], and at all levels of xLi+ we find the presence of lithium aggregates. Pulsed field gradient spin-echo NMR measurements of diffusion and electrochemical impedance spectroscopy measurements of ionic conductivity are made for the neat ionic liquids as well as 0.5 molal solutions of Li-salt in the ionic liquids. Bulk ionic liquid properties (density, diffusion, viscosity, and ionic conductivity) are obtained with MD and show excellent agreement with experiment. While the diffusion exhibits a systematic decrease with increasing xLi+, the contribution of Li+ to ionic conductivity increases until reach- ing a saturation doping level of xLi+ 0.10. Comparatively, the Li+ conductivity of [pyr14][TFSI] is an order of magnitude lower than that of the other liquids, which range between 0.1-0.3 mScm. Our transport results also demonstrate the necessity of long MD simulation runs ( 200 ns) required to converge transport properties at room T. The differences in Li+ transport are reflected in the residence times of Li+ with the anions (Li), which are revealed to be much larger for [pyr14][TFSI] (up to 100 ns at the highest doping levels) than in either [EMIM][BF4] or [pyr13][FSI]. Finally, to comment on the relative kinetics of Li+ transport in each liquid, we find that while the net motion of Li+ with its solvation shell (vehicular) significantly contributes to net diffusion in all liquids, the importance of transport through anion exchange (hopping) increases at high xLi+ and in liquids with large anions.

electrolytes↗
NASA NTRS1976

Refractive-index profile and physical process determination in thick gratings in electrooptic crystals

A method for determining the refractive index profile of thick phase gratings in linear electrooptic crystals is presented. This method also determines the effective photovoltaic electric field and the relative contributions of diffusion and drift during hologram recording. The method requires only a knowledge of the modulation ratio during hologram recording and the fundamental and the higher-order diffraction efficiencies of the grating. As an illustration of the method, the refractive index profile, the effective photovoltaic field, and the relative contributions of diffusion and drift are determined from experimental measurements for a lithium niobate holographic grating.

Su, S. F.↗
NASA NTRS1976

Corrosion of oxygen-doped tantalum by lithium

The increase in the penetration of tantalum by liquid lithium with increasing oxygen content of tantalum results from the ability of lithium to extract oxygen from tantalum oxides and/or from regions of high oxygen concentrations, accompanied by the creation of minute channels. At low oxygen concentration, oxides are present primarily at the grain boundaries and the lithium penetration is primarily intergranular. At high oxygen concentration, oxides and/or regions of high oxygen concentration are present both at the grain boundaries and within the grains; lithium penetration is both intergranular and transgranular. For a specific oxygen concentration, the severity of corrosion decreases with increasing temperature because (1) the oxygen solubility increases with temperature, decreasing the number of oxide particles and/or regions of high oxygen concentration, and (2) the diffusivity of oxygen in tantalum increases, allowing more rapid oxygen removal at the tantalum lithium interface.

Stecura, S.↗
NASA NTRS1974

Lithium-doped solar cell pilot line fabrication and test programs

An investigation was conducted to determine the technology readiness of lithium-doped silicon solar cells with respect to use in space programs. A pilot line fabrication program was established, in which the pilot line cells were evaluated after being exposed to environments ordinarily imposed on nonlithium-doped silicon solar cells. Results indicate that further process improvements are required, particularly with respect to the P/N junction diffusion and the electrical contacting technique (including solder coating). It is concluded that lithium-doped cells can be fabricated to exhibit (1) high efficiencies, (2) uniform cell-to-cell recovery characteristics after exposure to 1-MeV electrons; and (3) good stability in most environments investigated (the only exception being the thermal shock environment).

Berman, P. A.↗
NASA NTRS1991

An investigation of voids formation mechanisms and their effects on freeze and thaw processes of lithium and lithium fluoride

The mechanisms of void formation during the cooldown and freezing of lithium coolant within the primary loop of SP-100 type systems are investigated. These mechanisms are: (1) homogeneous nucleation; (2) heterogeneous nucleation; (3) normal segregation of helium gas dissolved in liquid lithium; and (4) shrinkage of lithium during freezing. To evaluate the void formation potential due to segregation, a numerical scheme that couples the freezing and mass diffusion processes in both the solid and liquid regions is developed. The results indicated that the formation of He bubbles is unlikely by either homogeneous or heterogeneous nucleation during the cooldown process. However, homogeneous nucleation of He bubbles following the segregation of dissolved He in liquid lithium ahead of the solid-liquid interface is likely to occur. Results also show that total volume of He void is insignificant when compared to that of shrinkage voids. In viewing this, the subsequent research focuses on the effects of shrinkage void forming during freezing of lithium on subsequent thaw processes are investigated using a numerical scheme that is based on a single (solid/liquid) cell approach. The cases of lithium-fluoride are also investigated to show the effect of larger volume shrinkage upon freezing on the freeze and thaw processes. Results show that a void forming at the wall appreciably reduces the solid-liquid interface velocity, during both freeze and thaw, and causes a substantial rise in the wall temperature during thaw. However, in the case of Li, the maximum wall temperature was much lower than the melting temperature of PWC-11, which is used as the structure material in the SP-100 system. Hence, it is included that a formation of hot spots is unlikely during the startup or restart of the SP-100 system.

El-Genk, Mohamed S.↗
NASA NTRS1991

Mechanisms of voids formation during cooldown and freezing of lithium in SP-100 type systems

The mechanisms of void formation during the cooldown and freezing of lithium coolant within the primary loop of SP-100 type systems are investigated. These mechanisms are: (a) homogeneous nucleation, (b) heterogeneous nucleation, (c) normal segregation of helium gas dissolved in liquid lithium, and (d) shrinkage of lithium during freezing. To evaluate the void formation potential due to segregation, a numerical scheme that couples the freezing and mass diffusion processes in both the solid and liquid regions is developed. The results indicated that the formation of He bubbles is unlikely by either homogeneous or heterogeneous nucleation during the cooldown process. However, homogeneous nucleation of He bubbles following the segregation of dissolved He in liquid Lithium ahead of the solid-liquid interface is likely to occur. Results also show that total volume of He void is insignificant when compared to that of shrinkage voids.

Yang, Jae Y.↗
NASA NTRS2018

Molecular Dynamics Simulations of Liquid and Polymer Electrolytes for Energy Storage Devices

Advancing beyond current lithium-ion technology is necessary in order to enable energy storage devices for electric airplanes. Electrolyte stability is a key limiting factor, yet the design of improved electrolytes remains a formidable challenge. Molecular dynamics (MD) simulations are a powerful tool for studying electrolytes, since they can be used to evaluate structural, thermodynamic, and transport properties, and can provide molecular-level detail often inaccessible to experimental techniques. Our computational materials groups at the NASA Ames Research Center has developed models and methods to accurately simulate both liquid and polymer electrolytes.We report the results from atomistic MD simulations of several electrolyte materials, with lithium salts dissolved in ionic liquids, dimethoxyethane (DME), and polyethylene oxide (PEO). For improved accuracy, we employ polarizable models, where each atom is given an environment-dependent atomic dipole. The simulations accurately predict bulk transport properties, including viscosity, diffusion, and ionic conductivity, in quantitative agreement with available experimental data. Moreover, the simulations provide important insights into the solvation structure of the lithium ions.We also report the results from coarse-grained MD simulations of polyanion electrolytes. In order to more efficiently capture the longer length- and time-scales of these systems, we employ a generic bead-spring model. These simulations provide important insight into how the polymer chain architecture and ionic interaction strengths affect the ionic aggregation behavior and cation dynamics. Despite the simplicity of the model, the simulations yield qualitative agreement with experimental data for similar systems.

Abbott, Lauren J.↗
NASA NTRS1971

Space thermal control development

The results of experimental investigations on a number of various phase change materials (PCMs) and PCMs in combination with metals and other materials are reported. The evaluations include the following PCM system performance characteristics: PCM and PCM/filler thermal diffusivities, the effects of long-term thermal cycling, PCM-container compatibility, and catalyst effectiveness and stability. Three PCMs demonstrated performance acceptable enough to be considered for use in prototype aluminum thermal control devices. These three PCMs are lithium nitrate trihydrate with zinc hydroxy nitrate catalyst, acetamide, and myristic acid. Of the fillers tested, aluminum honeycomb filler was found to offer the most increase in system thermal diffusivity.

Hoover, M. J.↗
NASA NTRS2015

Flexible Hybrid Battery/Pseudocapacitor

Batteries keep devices working by utilizing high energy density, however, they can run down and take tens of minutes to hours to recharge. For rapid power delivery and recharging, high-power density devices, i.e., supercapacitors, are used. The electrochemical processes which occur in batteries and supercapacitors give rise to different charge-storage properties. In lithium ion (Li+) batteries, the insertion of Li+, which enables redox reactions in bulk electrode materials, is diffusion controlled and can be slow. Supercapacitor devices, also known as electrical double-layer capacitors (EDLCs) store charge by adsorption of electrolyte ions onto the surface of electrode materials. No redox reactions are necessary, so the response to changes in potential without diffusion limitations is rapid and leads to high power. However, the charge in EDLCs is confined to the surface, so the energy density is lower than that of batteries.

Tucker, Dennis S.↗
NASA NTRS2023

3D Printed TiO 2 Negative Electrodes for Sodium-Ion and Lithium-ion Batteries using Vat Photopolymerization

Additive manufacturing, also called 3D printing, represents a unique approach to develop three dimensional shape-conformable batteries with enhanced electrodes, specific surface area, improved ion diffusion, and power. For the first time, the formulation of a composite photocurable resin loaded with battery electrochemically active components was designed to feed a vat photopolymerization (VPP) 3D printer. In direct alignment with NASA’s Artemis mission goals to develop sustainable lunar energy storage infrastructure necessary to support long-term human operations, TiO 2 was here selected as an active material for the negative electrode for sodium-ion and lithium-ion batteries due to its abundance on the lunar surface. The TiO 2 loading in the composite photocurable resin and in the resulting VPP-printed negative electrode was increased as high as possible to enhance the electrochemical performance, while simultaneously ensuring the printability and acceptable mechanical strength for sample handling. The effect of thermal post-processing on the electrical, electrochemical and mechanical performance is reported. Finally, a configurational study is implemented to identify the impact of two different electrode designs (cubic and gyroid lattice unit cells) on the electrochemical performance. This work addresses the difficulties related to the introduction of solid particles within a VPP photocurable resin and the need for a compromise between the electrochemical performances and printability to obtain fully functional VPP-printed electrodes.

sodium-ion battery↗
NASA NTRS1991

Analysis of redox additive-based overcharge protection for rechargeable lithium batteries

The overcharge condition in secondary lithium batteries employing redox additives for overcharge protection, has been theoretically analyzed in terms of a finite linear diffusion model. The analysis leads to expressions relating the steady-state overcharge current density and cell voltage to the concentration, diffusion coefficient, standard reduction potential of the redox couple, and interelectrode distance. The model permits the estimation of the maximum permissible overcharge rate for any chosen set of system conditions. Digital simulation of the overcharge experiment leads to numerical representation of the potential transients, and estimate of the influence of diffusion coefficient and interelectrode distance on the transient attainment of the steady state during overcharge. The model has been experimentally verified using 1,1-prime-dimethyl ferrocene as a redox additive. The analysis of the experimental results in terms of the theory allows the calculation of the diffusion coefficient and the formal potential of the redox couple. The model and the theoretical results may be exploited in the design and optimization of overcharge protection by the redox additive approach.

Narayanan, S. R.↗