Search NASA⌕ Search

SEARCH · Search NASA

Results for “membrane pore”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

Composite PEMs from Electrospun Crosslinkable Poly(Phenylene Sulfonic Acid)s (Final Technical Report)

The main objective of this project is to fabricate and demonstrate superior fuel cell performance of an electrospun composite all-hydrocarbon, non-PFSA membrane. The project builds on two earlier, DOE-funded studies demonstrating high proton conductivity, even at very low humidity of crosslinkable poly(phenylenesulfonic acid), cPPSA, solution cast films, and high durability of electrospun perfluorosulfonic acid (PFSA) composite membranes. Most project milestones were fully met but the best membrane conductivity and fuel cell performance were obtained with membranes that did not contain electrospun sulfonated polyphenylene, as initially planned. Instead, an excellent performance was achieved with membranes fabricated by pore-filling, either with electrospun poly(phenyl sulfone) scaffolds or with commercial, expanded polytetrafluoroethylene scaffolds. Fuel cell testing demonstrated performance better than that of Nafion 211 or Nafion XL, particularly at lower cell humidification levels with significantly lower hydrogen crossover. No accelerated stress testing was performed, due to the initial numerous difficulties with controlling the copolymerization reaction, which took excessive amount of time to overcome. Potential scale-up of the proposed composite membrane technology can aid in boosting the fuel cell power output and simplification of the cell hydration system.

08 HYDROGEN↗

Hierarchically porous and single Zn atom-embedded carbon molecular sieves for H2 separations

Abstract Hierarchically porous materials containing sub-nm ultramicropores with molecular sieving abilities and microcavities with high gas diffusivity may realize energy-efficient membranes for gas separations. However, rationally designing and constructing such pores into large-area membranes enabling efficient H 2 separations remains challenging. Here, we report the synthesis and utilization of hybrid carbon molecular sieve membranes with well-controlled nano- and micro-pores and single zinc atoms and clusters well-dispersed inside the nanopores via the carbonization of supramolecular mixed matrix materials containing amorphous and crystalline zeolitic imidazolate frameworks. Carbonization temperature is used to fine-tune pore sizes, achieving ultrahigh selectivity for H 2 /CO 2 (130), H 2 /CH 4 (2900), H 2 /N 2 (880), and H 2 /C 2 H 6 (7900) with stability against water vapor and physical aging during a continuous 120-h test.

42 ENGINEERING↗

A de novo sacrificial-MOF strategy to construct enhanced-flux nanofiltration membranes for efficient dye removal

Nanofiltration membanes play a critical role in alleviating global water scarcity, affecting more than 4 billion people. Here, a new metal organic framework (MOF) sacrificicial strategy is designed to synthesize flux-enhancing nanofiltration membrane for efficient dye removal. With the aid of polyphenol chemistry, ZIF-67 MOF was first coated onto a porous support and in situ transformed into a selective layer by virtue of pyrrole polymerization. Trigerred by ammonium persulfate, polypyrrole selective layer functioalized nanofiltration membrane was fabricated when accompanying pore regulation by MOF self-sacrifice. The membrane demonstrated a flux enhancement of 745% than pristine polypyrrole (PPy) one with maintained rejection. Furthermore, the synergistic interactions among polypyrrole, polyphenol, and porous support endowed membrane with excellent stability during long term test. The designed MOF sacrificed route may open a new avenue for fabricating advanced energetic-efficient membranes with the reconstructed architecture towards diverse separation applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Membrane-Confined Iron Oxychloride Nanocatalysts for Highly Efficient Heterogeneous Fenton Water Treatment

Heterogeneous advanced oxidation processes (AOPs) allow for the destruction of aqueous organic pollutants via oxidation by hydroxyl radicals ( • OH). However, practical treatment scenarios suffer from the low availability of short-lived • OH in aqueous bulk, due to both mass transfer limitations and quenching by water constituents, such as natural organic matter (NOM). In this work, we overcome these challenges by loading iron oxychloride catalysts within the pores of a ceramic ultrafiltration membrane, resulting in an internal heterogeneous Fenton reaction that can degrade organics in complex water matrices with pH up to 6.2. With • OH confined inside the nanopores (~ 20 nm), this membrane reactor completely removed various organic pollutants with water fluxes of up to 100 L m –2 h –1 (equivalent to a retention time of 10 s). This membrane, with a pore size that excludes NOM (>300 kDa), selectively exposed smaller organics to •OH within the pores under confinement and showed excellent resiliency to representative water matrices (simulated surface water and sand filtration effluent samples). Moreover, the membrane exhibited sustained AOPs (>24 h) and could be regenerated for multiple cycles. Our results suggest the feasibility of exploiting ultrafiltration membrane-based AOP platforms for organic pollutant degradation in complex water scenarios.

36 MATERIALS SCIENCE↗

Water transport through monolayer fullerene membrane

Water transport through nanoporous materials is important in water treatment, desalination, and nanofiltration. Two-dimensional (2D) membranes such as porous graphene have been explored for high-permeance water transport. However, water transport through a new class of 2D membranes based on two-dimensional covalently linked fullerene monolayers has not been fully explored. Here we use classical molecular dynamics simulations to investigate both vapor and liquid water transport through a monolayer fullerene membrane. We find that a quasi-tetragonal phase fullerene membrane possesses the right pore size and geometry that allows fast water vapor transport (∼ 50 g m −2 day −1 Pa −1 ) and water liquid transport (∼ 2.0 g m −2 day −1 Pa −1 ). Furthermore, simulation of sea water transport through the fullerene membrane shows 100 % salt rejection. The much faster vapor transport rate is attributed to the funnel-shaped pore and the optimal size that allows free rotation of water molecules permeating through, while the slower liquid transport is due to the need to desolvate a water molecule to break its hydrogen-bond network across the hydrophobic pore. This work shows the great potential of using monolayer fullerene membranes as 2D membranes for fast and selective water transport.

Desalination↗

The Earliest Ion Channels in Protocellular Membranes

Cellular membranes with their hydrophobic interior are virtually impermeable to ions. Bulk of ion transport through them is enabled through ion channels. Ion channels of contemporary cells are complex protein molecules which span the membrane creating a cylindrical pore filled with water. Protocells, which are widely regarded as precursors to modern cells, had similarly impermeable membranes, but the set of proteins in their disposal was much simpler and more limited. We have been, therefore, exploring an idea that the first ion channels in protocellular membranes were formed by much smaller peptide molecules that could spontaneously selfassemble into short-lived cylindrical bundles in a membrane. Earlier studies have shown that a group of peptides known as peptaibols is capable of forming ion channels in lipid bilayers when they are exposed to an electric field. Peptaibols are small, non-genetically encoded peptides produced by some fungi as a part of their system of defense against bacteria. They are usually only 14-20 residues long, which is just enough to span the membrane. Their sequence is characterized by the presence of non-standard amino acids which, interestingly, are also expected to have existed on the early earth. In particular, the presence of 2-aminoisobutyric acid (AIB) gives peptaibols strong helix forming propensities. Association of the helices inside membranes leads to the formation of cylindrical bundles, typically containing 4 to 10 monomers. Although peptaibols are excellent candidates for models of the earliest ion channels their structures, which are stabilized only by van der Waals forces and occasional hydrogen bonds between neighboring helices, are not very stable. Although it might properly reflect protobiological reality, it is also a major obstacle in studying channel behavior. For this reason we focused on two members of the peptaibol family, trichotoxin and antiamoebin, which are characterized by a single conductance level. This indicates that their structures are unique and stable. In addition, it is also believed that the trichotoxin channel displays some selectivity between potassium and chloride ions. This makes trichotoxin and antiamoebin ideal models of the earliest ion channels that could provide insight into the origins of ion conductance and selectivity. In the absence of crystal structure of the trichotoxin and antiamoebin channels, we propose their molecular models based on experimentally determined number of monomers forming the bundles. We use molecular dynamics simulations to validate the models in terms of their conductance and selectivity. On the basis of our simulations we show that the emergence of channels built of small, alpha-helical peptides was protobiologically plausible and did not require highly specific amino acid sequences, which is a convenient evolutionary trait. Despite their simple structure, such channels could possess properties that, at the first sight, appear to require markedly larger complexity. To this end, we will discuss how the amino acid sequence and structure of primitive channels give rise to the phenomena of ionic conductance and selectivity across the earliest cell walls, which were essential functions for the emergence and early evolution of protocells. Furthermore, we will argue that even though architectures of membrane proteins are not nearly as diverse as those of water-soluble proteins, they are sufficiently flexible to adapt readily to the functional demands arising during evolution.

Mijajlovic, Milan↗

Direct Chemical Vapor Deposition Synthesis of Porous Single-Layer Graphene Membranes with High Gas Permeances and Selectivities

Single-layer graphene containing molecular-sized in-plane pores is regarded as a promising membrane material for high-performance gas separations due to its atomic thickness and low gas transport resistance. However, typical etching-based pore generation methods cannot decouple pore nucleation and pore growth, resulting in a trade-off between high areal pore density and high selectivity. In contrast, intrinsic pores in graphene formed during chemical vapor deposition are not created by etching. Therefore, intrinsically porous graphene can exhibit high pore density while maintaining its gas selectivity. Here in this work, the density of intrinsic graphene pores is systematically controlled for the first time, while appropriate pore sizes for gas sieving are precisely maintained. As a result, single-layer graphene membranes with the highest H 2 /CH 4 separation performances recorded to date (H 2 permeance > 4000 GPU and H 2 /CH 4 selectivity > 2000) are fabricated by manipulating growth temperature, precursor concentration, and non-covalent decoration of the graphene surface. Moreover, it is identified that nanoscale molecular fouling of the graphene surface during gas separation where graphene pores are partially blocked by hydrocarbon contaminants under experimental conditions, controls both selectivity and temperature dependent permeance. Overall, the direct synthesis of porous single-layer graphene exploits its tremendous potential as high-performance gas-sieving membranes.

chemical vapor deposition↗

Pore-Filled PEMs from Poly(Phenylene Sulfonic Acid)s and Electrospun Poly(Phenylene Sulfone) Fiber Mats

A novel, composite, non-PFSA-based fuel cell membrane has been fabricated using a pore filling technique. The membrane consists of a mechanically stabilizing skeleton from an electrospun poly(phenylene sulfone) (PPSU) fiber mat and a thermally crosslinkable poly(phenylene sulfonic acid) (cPPSA) proton conducting ionomer that fills the interfiber voids. cPPSA copolymer was synthesized using Ullmann coupling copolymerization of 4,4-dibromobiphenyl 3,3-disulfonic acid with 1,4-dibromobenzene-2,5-disulfonic, followed by grafting a certain fraction of backbone sulfonic acid groups with biphenyl linker. The PPSU fiber mat was electrospun from NMP/acetone solution. Pore-filling was carried out by pouring a solution of cPPSA in methanol over the mat, followed by heating at 70°C to evaporate solvent. The cPPSA was crosslinked by an additional heating step, in a vacuum oven at 210°C for 5 hours. Here the resultant membrane had excellent proton conductivity, 5 times greater than that of Nafion® 211 in the 40-90% RH range at 80°C.

25 ENERGY STORAGE↗

Poly(ether‐block‐amide) membrane with deformability and adjustable surface hydrophilicity for water purification

Abstract Freshwater resources are currently insufficient, and another form of freshwater resources, namely, ice, is very interesting except for the issue of how to use new materials for effective purification during the processing procedure. In this article, a new membrane material with multisize pore structure in the cross‐section and intact thin skin layer on the upper and lower surfaces was successfully prepared by adding porogen, filler and setting heating environment during the phase separation process. The membrane exhibits excellent axial deformability, and its elongation at break can reach to 160% strain. Meanwhile, they all show elastic deformation behavior in the range from −60 to 100°C. Even if high content of hydrophobic filler is compounded into these membranes, that is, 5.7 wt% carbon tube content, water contact angle of membrane's surface is only 72.5°, demonstrating obvious hydrophilicity. In addition, in the water purification process, the adsorption rate constant reached ideal value of 0.26 s −1 , and the equilibrium adsorption capacity was about 2.8 g/g, showing fast and efficient water purification ability. In the mode of external heating source or the membrane's heat dissipation, these prepared membranes can melt the ice to obtain purified water and exhibit a controllable purification ability in this process.

Ge, Chengbiao↗

Simulation of Reverse Osmosis Membrane Compaction Using Material Point Method

Reverse Osmosis (RO) is a promising technology to address the impending water-crisis in the upcoming decades. RO at high salinities and high pressures is challenging due to membrane compaction that changes its porosity and permeability. In this study, we present a simulation methodology for membrane structural mechanics to understand pore size distribution and permeability variations under high pressure. We use the material point method (MPM), that solves the solid mechanics equations in a Lagrangian framework. MPM provides many features that make it well-suited for simulating mesoporous membranes. The Lagrangian framework allows for large deformations, easy integration of constitutive models and direct import of complex geometries as particles. The spatial discretization in our MPM solver is achieved using linear or cubic-spline shape functions while the time integration is carried out using the explicit Euler method. A series of images containing detailed pore structures obtained from X-ray tomography is first converted to a collection of material points. Compressive loads are applied to the top layer of the membrane to simulate the application of pressure. The membrane deformation and pore size distribution before and after load application are reported and compared with the experimental measurements. The presentation discusses the numerical methods used, the performance of the solver on high-performance computing machines, and the results of membrane compact in detail.

compaction↗

A hydroponic method for plant growth in microgravity

A hydroponic apparatus under development for long-term microgravity plant growth is described. The capillary effect root environment system (CERES) is designed to keep separate the nutrient and air flows, although both must be simultaneously available to the roots. Water at a pressure slightly under air pressure is allowed to seep into a plastic depression covered by a plastic screen and a porous membrane. A root in the air on the membrane outer surface draws the moisture through it. The laboratory model has a wire-based 1.241 mm mesh polyethylene screen and a filter membrane with 0.45 micron pores, small enough to prohibit root hair penetration. The design eliminates the need to seal-off the plant environment. Problems still needing attention include scaling up of the CERES size, controlling biofouling of the membrane, and extending the applications to plants without fibrous root systems.

Wright, B. D.↗

Freestanding self-assembled sulfonated pentablock terpolymer membranes for high flux pervaporation desalination

Pervaporation desalination has several advantages over competing desalination technologies, most notably an ability to select for or against volatile organic compounds and the ability to process high salinity feeds at a low transmembrane pressure. Pervaporation has not been commercialized for desalination applications because of its energy intensity. However, emerging processes such as hydraulic fracturing produce high total dissolved solids (>30-45 g/L) byproduct streams that exceed the operational limits of traditional reverse osmosis and could be treated by pervaporation. Here, we demonstrate free-standing pervaporation membranes with excellent permeance and high salt removal based on a partially sulfonated pentablock terpolymer with the tradename Nexar™. Pervaporation membranes were easily cast from this material with desalination performances comparable or superior to commercially available membranes. We found that the polymer degree of sulfonation and casting solvent polarity had a significant impact on the membranes’ water uptake but only a modest impact on the pervaporation desalination performance. Membranes with a degree of sulfonation of 52% (2.0 meq g –1 IEC) and a casting solution composed of 50 wt% n-propanol and 50 wt% toluene achieved a water flux of 3.32 kg m -2 h -1 (permeance 135 kg m -2 h -1 bar -1 ) with 99.5% salt removal in pervaporation from a 32 g/L –1 sodium chloride feed solution at room temperature. We demonstrated that dense, non-porous NexarTM pervaporation membrane permeance and salt separation performance were superior to commercial pervaporation membranes and equivalent to commercial membrane distillation membranes, which have much larger pores. Here, this study demonstrates that commercially available sulfonated pentablock terpolymers are excellent membranes for pervaporation desalination because of their ease of casting and excellent performance.

42 ENGINEERING↗

De novo design of transmembrane β barrels

Transmembrane β-barrel proteins (TMBs) are of great interest for single-molecule analytical technologies because they can spontaneously fold and insert into membranes and form stable pores, but the range of pore properties that can be achieved by repurposing natural TMBs is limited. We leverage the power of de novo computational design coupled with a “hypothesis, design, and test” approach to determine TMB design principles, notably, the importance of negative design to slow β-sheet assembly. We design new eight-stranded TMBs, with no homology to known TMBs, that insert and fold reversibly into synthetic lipid membranes and have nuclear magnetic resonance and x-ray crystal structures very similar to the computational models. These advances should enable the custom design of pores for a wide range of applications.

Vorobieva, Anastassia A.↗

Spectral Analysis of Regular Material Point Method and its Application to Study High Pressure Reverse Osmosis Membrane Compaction and Embossing

Material Point Method (MPM) is gaining widespread interest in applied continuum mechanics. The fact that all the continuum properties are stored on the particles (or material points) and the governing equations are solved on these material points makes MPM extremely suited to problems involving severe material deformations, such as crack propagation, soil movement, and fluid flows. Despite its popularity, only a few studies have focused on the numerical properties of MPM. This presentation introduces a global spectral analysis of the regular material point method. Contrary to previous studies, the analysis focuses on the numerical properties of the method in the spectral space. The amplification factor is derived as a function of the non- dimensional wave numbers. It provides insights into the stability and dissipative properties of the method for various CFL and Fourier numbers. The effect of the grid shape functions, number of particles per cell and their locations inside the grid cell are also analyzed. The EXAGOOP MPM solver (https://github.com/NREL/Exagoop.git) is developed at the National Renewable Energy Laboratory as a part of the NAWI UHPRO project and is based on the AMReX framework. A single-level, uniform cartesian grid is used as the background mesh, while the particle class in AMReX is used to manage the material point operations. Linear hat and B-splines are used as grid shape functions, while the time integration is performed using explicit Euler time integration. EXAGOOP is both CPU and GPU compatible and has been demonstrated to work well on multiple compute architectures. The performance of EXAGOOP on various computing architectures is presented along with its application to study compaction and embossing of high-pressure reverse osmosis membranes. The MPM solution accurately reproduces the membrane deformation. The deformed pore size and structure simulated using MPM also agree well with experimental SEM images.

material point method↗

Application of GO anchored mediator in a polymer electrolyte membrane for high-rate solid-state supercapacitors

Here, we synthesized a novel polymer electrolyte membrane by combining poly (vinylidene fluoride) (PVDF) and lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) with graphene oxide (GO) nanosheets and a lithium salt of tungstosilicic acid (Li 4 SiW 12 O 40 , hereafter, referred to SiWLi). The impact of the addition of GO/SiWLi on the microstructure and morphology of the membrane were characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), Fourier transform infrared spectroscopy (FTIR), and X-ray photoelectron spectroscopy (XPS). We found that adding the GO/SiWLi to the PVDF/LiTFSI polymer electrolyte membrane significantly reduced the pore size. Furthermore, the addition of the GO/SiWLi resulted in not only an increase of the ionic conductivity from 0.87 $\times$ 10 –2 to 3.12 $\times$ 10 –2 Scm –1 but also an increase in the lithium-ion transference number from 0.52 to 0.87. The polymer electrolyte membranes with and without GO/SiWLi were utilized to fabricate solid-state supercapacitors. The supercapacitors fabricated with the membrane containing GO/SiWLi displayed 37.2% lower equivalent series resistance and 88.2% greater specific capacitance than those fabricated using the membrane without GO/SiWLi at 200mVs –1 .

42 ENGINEERING↗