Search NASA⌕ Search

SEARCH · Search NASA

Results for “metal impurities”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Comparing the Purity of Rolled versus Evaporated Lithium Metal Films Using X-ray Microtomography

Here, we present a comparison of lithium metal films produced via rolling and thermal evaporation using synchrotron hard X-ray microtomography. In past studies of rolled lithium metal foils, a large number of C, O, and N impurities were found and identified as the key cause for failure in lithium metal cells. In this comparison, the X-ray tomography data show that the evaporated lithium metal films have an average impurity concentration of 19 particles/mm3 in comparison to 1350 particles/mm3 in the rolled lithium metal. An analysis of the inner substrate/lithium interface and outer lithium surface of the thermally evaporated film shows a much greater concentration of impurities at these interfaces, further emphasizing the importance of interface engineering in producing high-quality lithium metal batteries. Furthermore, we show that, if surface contamination can be avoided, it is possible to obtain lithium films with no impurities detectable by synchrotron hard X-ray tomography.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Best Practices for Shielding Analyses of Activated Metals and Spent Resins from Reactor Operation

This report investigated best practices for performing shielding evaluations of Type B waste packages, as defined in 10 CFR Part 71 regulations on packaging and transportation of radioactive material, or packages for which the contents are not defined before loading and may include a broad range of nuclides, geometries, and non-fuel materials. The following non-fuel waste streams were analyzed: Activated metals from decommissioned commercial power reactors, including Type 304 stainless steel, reactor vessel steel, and Inconel, Control blades from boiling water reactors, Neutron-activated corrosion products on surfaces of activated metals, and Spent resins from power plant operations. Measured elemental compositions, including major constituents and impurities, for steel and Inconel samples from commercial power reactors were used in activation calculations to determine radionuclide inventories in activated metals. For a simplified cask model, 60 Co contribution to the total external package dose rate at 30 days after shutdown varied from approximately 60% to 95%, depending on the activated metal, initial cobalt impurity concentration in the metal, and the thickness of the overpack gamma shield. Its maximum contribution to the total external package dose rate of approximately 100% was reached within the time interval of 2 to 5 years after shutdown and was maintained for up to 45 to 60 years after shutdown, depending on material, initial cobalt impurity concentration, and shield thickness. Thereafter, the 60 Co contribution to external package dose rate decreased with increasing decay time. Cobalt-60 is primarily produced by neutron reactions with the cobalt impurity in steel and Inconel. Other important radionuclides in activated metals contributing to package external dose rate are radionuclides with relatively short decay times, including 51 Cr, 59 Fe, 58 Co, and 54 Mn. These radionuclides may be represented as an equivalent 60 Co activity/source because 60 Co gamma ray emissions are bounding in terms of source strength and energy to other important radionuclides identified in the analyzed activated metals. Approaches for modeling the neutron-activated corrosion products that may be attached to activated reactor components were analyzed in this report. It was demonstrated that a surface source is more conservative than a uniform volumetric source for the treatment of neutron-activated corrosion products with respect to external package dose rates. An analysis of the maximum radionuclide loadings reported on spent resins identified the radionuclides 137 Cs, 60 Co, 134 Cs, 65 Zn, and 58 Co as the primary contributors to external package dose rate. For a resin cooled for 3.08 years, the external package dose rate was entirely produced by the reported 137 Cs and 60 Co inventory. The neutron sources from actinides found on spent resins or activated metals produced negligible dose rates and may be ignored in dose rate analyses. Effects of idealized waste material, source geometry, and spatial material/source distributions on external package dose rates were determined based on dose rate results for a simplified cask model under normal conditions of transport. Type 304 stainless steel, zirconium, and aluminum with adjusted mass densities based on a maximum content weight were analyzed for material modeling effects on external package dose rate. These materials produced identical external package dose rates within the statistical uncertainties of the dose rate estimates. Among four different source geometry configurations with homogeneous material of different mass densities, uniform volumetric source distribution, and the same source strength, the geometry configuration with lowest mass density (i.e., minimum self-shielding effect among the four cases) was most conservative. Spatial source distributions that better represent localized peak 60 Co activity values were more conservative than a uniform volumetric source distribution, assuming the same weight and total source strength per package. The increase in external dose rate caused by localized source peaks can be as much as the ratio between source peak activity density to average activity density, depending on the location of the activated metal with peak activity density. Therefore, the shielding analysis may be simplified if localized peak activities and the average activity per package can be measured/determined and documented at the time of cask loading. For simplicity, external package dose rates may be determined based on average source activity and a uniform volumetric source distribution. The dose rate results from that calculation model multiplied by the ratio of peak activity density to average activity density will produce maximum dose rate values for conservative estimates.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

Elucidating Hydrogen Reaction-Induced Water Desorption from Oxide-Passivated Metal Surfaces for Plasma Applications

Elucidating the mechanisms responsible for sub-microsecond desorption of water and other impurities from electrode surfaces at high heating rates is crucial for understanding pulsed power behavior. Ionization of desorbed impurities in the vacuum regions causes power or current loss; devising methods to limit such desorption during the short time scale of pulsed power is needed to improve corresponding applications. Previous molecular modeling studies have strongly suggested that, under high vacuum conditions, the amount of water impurity desorbing from oxide surfaces on metal electrodes is at a sub-monolayer level at room temperature, which appears insufficient to explain observed pulsed power energy losses at high current densities. In this work, we apply Density Functional Theory (DFT) techniques to show that hydrogen trapped inside iron metal can diffuse into hematite (α-Fe 2 O 3 ) on the metal surface, ultimately reacting with the oxide to form Fe(II) and H 2 O. The latter desorbs at elevated temperature and may explain the anomalous amount of desorbed impurity inferred from pulsed-power experiments. We also apply a suite of characterization techniques to demonstrate that when iron metal is heated to 650 °C, the dominant surface oxide component becomes α-Fe 2 O 3 . The oxide facets exposed are found to be a mixture of (0001), (10-10), and others, in agreement with the DFT models used.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2021

Evolution of Metastable Phases During Mg Metal Corrosion: An In Situ Cryogenic X-ray Photoelectron Spectroscopy Study

Magnesium and its alloys are potential structural materials candidates for a wide variety of applications due to their high strength-to-weight ratio. However, ductility and poor corrosion resistance under ambient environmental conditions are the bottleneck for industrial deployment. Designing passivation layers and/or corrosion resistant alloys requires fundamental understanding of the corrosion process. The traditional ex-situ spectroscopic measurements of polycrystalline metal surface with ubiquitous surface impurities and grain boundaries only provided an indistinct view of the corrosion process. To clearly distinguish the mechanism and sequence of corrosion process, we employed in-situ cryo-based x-ray photoelectron spectroscopy (XPS) measurements on Mg single crystal surface exposed to aqueous salt solution. Clean Mg (0001) surfaces were exposed to pure D2O and NaCl aqueous solution (5 wt% NaCl+95 wt% D2O). The interfacial reactions were studied using multimodal analysis including XPS, x-ray diffraction (XRD) and scanning electron microscopy (SEM). In contrast to previous studies, our experiments demonstrated the formation of magnesium chloride hydroxide hydrate during aqueous salt corrosion processes. Evidence of metastable ClO* radicals were also found during the initial aqueous salt solution exposure.

Shutthanandan, Vaithiyalingam↗
DOE OSTI2023

Structural features of early fuel cycle taggant incorporation for intentional nuclear forensics

To develop strategies for incorporating transition metal taggants (Fe, Cr, and Ni) into oxide fuels and to understand how these taggant candidates persist through early fuel cycle processes, synthetic procedures are modified from established production routes to yield intentionally tagged early fuel cycle intermediates including uranyl nitrate hexahydrate (UNH, UO 2 (NO 3 ) 2 ·6H 2 O), uranyl peroxide tetrahydrate (studtite, UO 2 O 2 ·4H 2 O), and uranyl peroxide dihydrate (metastudtite, UO 2 O 2 ·2H 2 O). First, Fe, Cr, and Ni nitrate solutions are introduced to an aqueous solution of UNH followed by precipitation to produce tagged UNH. Then, studtite is precipitated from UNH followed by dehydration to metastudtite. Structural influences of taggant incorporation within all synthesized phases are investigated using powder X-ray diffraction (PXRD) and Raman spectroscopy to provide insight into crystallographic modifications resulting from the addition of tags to these early fuel cycle materials and elucidate the chemical form of taggants introduced at these stages. The possibility of segregation of taggant species into discrete phases within U matrices was examined using scanning electron microscopy with energy dispersive X-ray spectroscopy. Taggant concentrations in solid-phase materials were determined using inductively coupled plasma-optical emission spectroscopy. Observations from Raman spectroscopy and PXRD indicate that introducing transition metal tags during uranyl nitrate precipitation results in potential impurity phase segregation in UNH, but transition metal incorporation is suggested by results for tagged uranyl peroxide materials. Further, results from this study will inform strategies for optimizing taggant incorporation in UO 2 .

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Liquid metal walls

Here, the plasma performance of fusion devices depends strongly on the chosen wall materials. Solid plasma-facing components (PFCs) are predominantly used in present devices, and are the most investigated candidates for fusion designs. High-Z materials such as tungsten (W) are the leading solid PFC material candidates. To date, a material choice that scales to steady-state reactor conditions has not been identified. Moreover, if plasma transient events such as edge-localized modes and disruptions cannot be altogether avoided or sufficiently mitigated, the projected peak heat and particle loads far exceed the power exhaust capabilities of solids. Liquid metal (LM) PFCs represent an intrinsic self-healing boundary that are both resilient to surface damage from transients, and that could handle high steady-state heat and particle fluxes. Flowing LM PFCs can be designed to remove “slag,” the buildup of material erosion due to plasma-material interactions, including charge exchange sputtering in the main chamber. Further, LM offer the prospect to manage hydrogenic species otherwise retained in the PFCs, which is important from a safety and inventory standpoint. The two most promising LMs are lithium (Li) and tin (Sn), although Sn–Li eutectics may be considered. While Sn offers a higher temperature window with low vapor pressure and low hydrogen retention, Li offers the prospect of enhanced energy confinement and higher acceptable core contamination limits, and this section focuses on Li PFCs. An LM PFC development research program developed LM PFC concepts for a nuclear fusion device via engineering design calculations, single-effect experiments, and staged prototypical experiments. A self-consistent design window was identified with liquid Li flow speeds ~5–10 m/s; plasma contamination was negligible for predicted Li evolution rates. While these preconceptual designs hold promise, there is substantial R&D needed to advance the technical readiness levels of LM PFCs for application to fusion power plants.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Enhancing MnBi 2 Te 4 Stability by Doping

MnBi 2 Te 4 (MBT) is an intrinsically magnetic topological material that possesses unique properties due to the quantum Hall effect. However, the low Mn–Bi mixed antisite formation energy is detrimental to these properties as it alters the long-range magnetic ordering in the Mn layer. Therefore, it is crucial to destabilize the antisite defects in MBT while preserving the favorable electronic properties. Here, to this end, we utilized a screening approach to understand the role of dopants in the Mn and Bi sites. We find that Sc, Y, and La dopings prefer substitutions on the Bi site and significantly increase the Mn–Bi antisite defect formation energy. We find that the contribution from the empty s and d states of Sc, Y, and La around the Fermi level is insignificant. However, at the high concentration limit, the Bi–Te octahedra are significantly modified with doping, leading to important changes in the band structure.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Boosting the Oxygen Evolution Reaction by Tuning the Interfacial Iron Adsorption on Layered Double Hydroxide

Understanding the interaction between ions in the electrolyte and electrode materials plays an important role in optimizing the water electrolysis performance for hydrogen production. Herein, the synergistic effect of iron (Fe) in the electrolyte and interlayer anions within the layered structure on the oxygen evolution reaction (OER) has been investigated by combining material synthesis with controlled structure, multiple characterization techniques, and first-principles calculations. Nickel aluminum layered double hydroxides (NiAl-LDHs) with different interlayer anions (CO 3 2– , Cl – , and Br – ) show similar oxygen evolution activity in the absence of Fe species in the electrolyte. The addition of Fe into the electrolyte results in improved performance for all of the NiAl-LDHs, following the rank LDH-Br > LDH-Cl > LDH-CO 3 , under all of the conditions with varied concentration of Fe. X-ray absorption spectroscopy and identical location electron microscopy analyses show that the LDH structure remains unchanged after the OER activity test, while in situ stationary probe rotating disk electrode inductively coupled plasma mass spectrometry (SPRDE-ICP-MS) measurements show partial dissolution of the intercalating halide ions during cycling, with less dissolution for Br-intercalated materials. Insights from theoretical calculations demonstrate the thermodynamic preference of Br – to remain intercalated in the presence of Fe, while the stronger adsorption of Fe(OH) 3 species on the LDH-Br sample promotes the OER activity. In conclusion, these results provide mechanistic insights into the rational design of active layered materials with an enhanced OER performance for efficient water electrolysis.

58 GEOSCIENCES↗
DOE OSTI2021

Spin-dependent vibronic response of a carbon radical ion in two-dimensional WS 2

Atomic spin centers in 2D materials are a highly anticipated building block for quantum technologies. Here, we demonstrate the creation of an effective spin-1/2 system via the atomically controlled generation of magnetic carbon radical ions (CRIs) in synthetic two-dimensional transition metal dichalcogenides. Hydrogenated carbon impurities located at chalcogen sites introduced by chemical doping are activated with atomic precision by hydrogen depassivation using a scanning probe tip. In its anionic state, the carbon impurity is computed to have a magnetic moment of 1 μ B resulting from an unpaired electron populating a spin-polarized in-gap orbital. We show that the CRI defect states couple to a small number of local vibrational modes. The vibronic coupling strength critically depends on the spin state and differs for monolayer and bilayer WS 2 . The carbon radical ion is a surface-bound atomic defect that can be selectively introduced, features a well-understood vibronic spectrum, and is charge state controlled.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Examination of 3013 Containers Baseline Surface Features

The Surveillance and Monitoring Program at Los Alamos National Laboratory (LANL) was tasked with evaluating the baseline features of 3013 containers. This baseline is to be used as a basis for comparison for 3013 containers that had been packaged with corrosive plutonium materials. The LANL team evaluated an unwelded container, an unused welded container, and a welded container that had held plutonium metal without any corrosive impurities. These three containers had features with depths no larger than 6 µm and had similar depth distributions. The features observed in the baseline containers were all shallower than those seen in containers packaged with corrosive plutonium materials. This work establishes workflows for feature identification and measurement, as well as establishment of baseline data for future comparison with corroded containers.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Enhancing CO 2 Mineralization Rate and Extent of Iron and Steel Slag via Grinding

Roughly 10% of the CO 2 emissions from iron and steel making are attributable to the direct release of CO 2 from the thermal decomposition of carbonates to produce flux, mainly CaO, used for impurity removal. Notably, these direct emissions remain even if carbon-based steelmaking is replaced by hydrogen-based steelmaking. After removing impurities from the molten metal, this flux becomes the solid waste product called ‘slag’, a primarily Ca-silicate material. The transformation of slag back into carbonates is thermodynamically spontaneous with negative ΔG in the ambient environment, meaning that ~10% of the CO 2 emissions from iron and steel making could be negated if equipment and methods were developed to support CO 2 mineralization. However, the rate of CO 2 mineralization using slag is slowed by several environmental, geometric, and processing factors. We leverage an experimentally verified model of CO 2 mineralization to determine how to efficiently accelerate the process. Increasing the crystallinity of slag, increasing the relative humidity, and reducing the grain size of slag particles provide the greatest increase in CO 2 mineralization rate at the lowest energy penalty. Increasing the concentration of CO 2 and the temperature provide only modest increases in the CO 2 mineralization rate while incurring a substantial energy penalty. For steelmaking slags, CO 2 mineralization represents low-hanging fruit as the current reuse pathways are low value. For ironmaking slag, replacing the production of amorphous slag for the cement industry with the production of crystalline slag for CO 2 mineralization becomes financially preferable when a carbon price/tax exceeds 67.40 USD/t-CO 2 .

42 ENGINEERING↗
DOE OSTI2022

Nitrogen-doped carbon for selective pseudo-metal-free hydrodeoxygenation of 5-hydroxymethylfurfural to 2,5-dimethylfuran: Importance of trace iron impurity

Heteroatoms-doped carbon materials have recently emerged as effective catalysts for various chemical and electrochemical reactions. The free of metals especially noble metals reduces cost and eliminates issues like sintering or leaching of metals at elevated temperatures in solvents. In this work, selective hydrodeoxygenation (HDO) of 5-hydroxymethylfurfural (HMF) to 2,5-dimethylfuran (DMF) is for the first time achieved over simple nitrogen-doped carbon (N-C) catalysts. Further, at optimal reaction conditions, a 91% yield of DMF is obtained with excellent catalyst stability. Extensive characterization, including extended X-ray absorption fine-structure (EXAFS) and soft X-ray absorption spectroscopy (sXAS), model reactions, basic data science analysis, and DFT calculations suggest that ppm of Fe in particular FeN 3 sites formed in pyrolysis, rather than non-metallic elements, drive key steps such as H 2 activation and deoxygenation of –OH during HMF HDO.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Intentional carbon doping reveals CH as an abundant charged impurity in nominally undoped synthetic WS 2 and WSe 2

Understanding the physical properties and controlling the generation of intrinsic and extrinsic defects is central to the technological adoption of 2D materials in devices. Here we identify a charged carbon-hydrogen complex at a chalcogen site (CH X ) as a common, charged impurity in synthetically grown transition metal dichalcogenides (TMDs). This conclusion is drawn by comparing high resolution scanning probe microscopy measurements of nominally undoped and intentionally carbon doped TMD samples. While CH impurity densities in undoped CVD-grown WS 2 and MOCVD-grown WSe 2 can range anywhere from parts per million to parts per thousand, CH densities in the percentage levels were selectively generated by a post-synthetic methane plasma treatment. Our study indicates that methane plasma treatment is a selective and clean method for the controlled introduction of a charged carbon-hydrogen complex at a surface chalcogen site, adefect that is commonly present in synthetic TMDs.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Toward achieving cost-effective hexagonal BN semi-bulk crystals and BN neutron detectors via halide vapor phase epitaxy

Presently, thermal neutron detectors fabricated from boron-10 enriched hexagonal boron nitride (h-10BN) ultrawide bandgap semiconductor grown by metal organic chemical vapor deposition (MOCVD) hold the record high detection efficiency among all solid-state detectors at 59%. To overcome the short comings of MOCVD growth, including inherently low growth rate and unavoidable impurities such as carbon in metal organic source, we demonstrate here the growth of natural hexagonal boron nitride (h-BN) semi-bulk wafers using halide vapor phase epitaxy (HVPE), which is an established technique for producing GaN semi-bulk crystals at a high growth rate. Electrical transport characterization results revealed that these HVPE grown materials possess an electrical resistivity of 1 × 1013 Ω cm, and a charge carrier mobility and lifetime product of 2 × 10−4 cm2/V s. Detectors fabricated from a 100 μm thick h-BN wafer have demonstrated a thermal neutron detection efficiency of 20%, corresponding to a charge collection efficiency of ∼60% at an operating voltage of 500 V. This initial demonstration opens the door for mass producing high efficiency h-BN semiconductor neutron detectors at a reduced cost, which could create unprecedented applications in nuclear energy, national security, nuclear waste monitoring and management, the health care industry, and material sciences.

Physics↗
DOE OSTI2024

Electronic conductivity in metal-graphene composites: the role of disordered carbon structures, defects, and impurities

Abstract This paper explores the transport properties of aluminum-carbon composite material via ab initio methods. Interfacial and electronic dynamics of the aluminum-graphene interface structure were investigated using models of amorphous graphene added to an aluminum matrix. We examine the impact on electronic conduction caused by the presence of nitrogen impurities within the interfacial amorphous graphene layer. We elucidate the conduction mechanisms by using a projection of the electronic conductivity into space.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Development of High Capacity Energy Storage Materials

Hydrogen fuel cells have the potential to offer energy and power density advantages over lithium ion batteries in automotive and portable power applications when paired with an appropriate hydrogen storage system. Development of the ideal hydrogen storage material has been immensely sought after but plagued by limitations present in each type of material. These limitations typically include nonidealistic operational temperatures, low capacities, excessive costs, lack of reversibility, or evolution of impurities which irreversibly damage fuel cell performance. Many complex metal hydrides possess suitable hydrogen capacities but unfortunately suffer from impurity release. In order to address this problem, our team has explored in-situ catalyst doping of alkali metal amides to demonstrate methodologies to reduce ammonia release. The incorporation of iridium metal in lithium amide significantly reduces the ammonia release and decomposes the ammonia to provide additional hydrogen. Furthermore, we demonstrate, for the first time, high resistance of low temperature fuel cells to ammonia in comparison with typical proton exchange membrane fuel cells. The utilization of these two approaches in tandem provides a novel pathway for the development and implementation of high capacity energy storage materials for fuel cell applications.

25 ENERGY STORAGE↗