Search NASA⌕ Search

SEARCH · Search NASA

Results for “microstructure characterization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

Formation Mechanisms and Microstructure Characterization of Al/Al{sub 3}Ni In-situ Composite by Compound Casting

The Compound casting method was used to produce an Al/Ni bimetal composite. The mechanisms of formation of the reinforcing intermetallic phases were studied and the produced bimetal composite’s microstructure was then characterized. The results showed that the Al/Ni interface consisted of two intermetallic layers including Al{sub 3}Ni{sub 2} and Al{sub 3}Ni. It is suggested that the Al{sub 3}Ni reinforcing particles of the composite originated from two sources. (1) Some Al{sub 3}Ni particles detached from the Al{sub 3}Ni layer formed at the interface between the Ni core and the Al melt and dispersed in the liquid Al and (2) Al-Al{sub 3}Ni eutectic phase, which formed during the solidification process. The increase in the temperature led to the formation of more reinforcing particles and extended the depth of dispersion of the particles in the Al matrix.

36 MATERIALS SCIENCE↗

Microstructural characterization of an SA508–309L/308L–316L domestic dissimilar metal welded safe-end joint

The microstructure of an SA508–309L/308L–316L domestic dissimilar metal welded safe-end joint was characterized in this work by optical microscopy, scanning electron microscopy (with electron back scattering diffraction) and micro-hardness testing. Epitaxial growth and competitive growth are evident in the 308L–316L fusion boundary regions. A martensite layer, carbon-depleted zones, and type-II and type-I boundaries are found in the SA508–309L fusion boundary regions, while only martensite and austenite mixed zones are observed in the SA508–308L fusion boundary regions. The microstructure near the fusion boundary and the microstructure transition in the SA508 heat affected zone are quite complex. Both for SA508–309L/308L and 308L–316L, the highest residual strain is located on the outside of the weldment. The residual strain and the grain boundary character distribution change with increasing distance from the fusion boundary in the heat affected zone of 316L. Micro-hardness measurements also reveal non-uniform mechanical properties across the weldment. - Highlights: • The microstructure of SA508 HAZ, especially near the FB, is very complex. • The outside of the dissimilar metal welded joint has the highest residual. • The micro-hardness distributions along the DMWJ are non-uniform.

36 MATERIALS SCIENCE↗

Microstructural characterization of transformable Fe-Mn alloys at different length scales

The as-annealed and deformed Microstructure of transformable Fe-Mn alloys were, comprehensively, characterized over a wide range of length scales. Differential interference contrast optical metallography, combined with a tinting etching method, was employed to examine the grain morphology. A new specimen preparation method, involving electro-polishing and electro-etching, was developed for scanning electron microscopy and electron back-scattered diffraction analysis. This method leads to a very good imaging contrast and thus bridges the length scale gap between optical metallography and transmission electron microscopy. Moreover, it enables simultaneous scanning electron microscopy and electron backscatter diffraction analysis which allows correlations among morphology, crystal orientation and phase analysis in the length scale of microns. Transmission electron microscopy investigations were also made to evaluate the thermal and mechanical transformation products as well as defect structures.

36 MATERIALS SCIENCE↗

Microstructural characterization and influence of manufacturing parameters on technological properties of vitreous ceramic materials

Microstructure of vitreous ceramic samples manufactured from kaolinitic-clay and feldspars raw materials from Cameroon was investigated in the range 1150-1250 deg. C by X-ray diffraction and scanning electron microscopy and by measuring some technological properties. Moreover, the simultaneous influence of feldspars content, heating temperature and soaking time on water absorption and firing shrinkage was evaluated by adopting the response surface methodology (Doehlert matrix), using the New Efficient Methodology for Research using Optimal Design (NEMROD) software. The results show that a spinel phase, mullite, glassy phase and some amount of hematite were formed. However, the spinel phase and potassic feldspar, as compared to the sodic one, disappeared at moderate firing temperature and soaking time. Apparently, mullite developed from spinel phase, which is formed from the demixion of metakaolin. On the other hand, it is found that the effects of fluxing content and firing temperature on the measured properties were almost similar and more influent than soaking time. Antagonistic and synergetic interactions existed between the considered parameters, and their importance differed for the considered properties. By using this mathematical tool, suitable operating conditions for manufacturing vitreous bodies were determined.

36 MATERIALS SCIENCE↗

Microstructural characterization of a new mechanically alloyed Ni-base ODS superalloy powder

The microstructure of a new Ni-base oxide dispersion strengthened superalloy powder was studied for high temperature gas turbine applications after the mechanical alloying process. In this study, an atomized powder with a composition similar to the CMSX-10 superalloy was mechanically alloyed with yttria and Hf powders. The mechanically alloyed powder included only the supersaturated solid solution γ phase without γ′ and yttria provided by severe plastic deformation, while after the 3-step aging, the γ′ phase was precipitated due to the partitioning of Al and Ta to the γ′ and Co, Cr, Re, W, and Mo to the γ phase. Mechanical alloying modified the morphology of γ′ to the new coherent γ–γ′ nanoscale lamellar structure to minimize the elastic strain energy of the precipitation, which yielded a low lattice misfit of 0.16% at high temperature. The γ′ lamellae aligned preferentially along the elastically soft [100] direction. Also, the precipitated oxide particles were refined in the γ phase by adding Hf from large incoherent YAlO{sub 3} to fine semi-coherent Y{sub 2}Hf{sub 2}O{sub 7} oxide particles with the average size of 7 nm and low interparticle spacing of 76 nm. - Highlights: • A new Ni-base ODS superalloy powder was produced by mechanical alloying. • The nanoscale γ–γ′ lamellar structure was precipitated after the aging treatment. • Fine semi-coherent Y{sub 2}Hf{sub 2}O{sub 7} oxide particles were precipitated by addition of Hf.

36 MATERIALS SCIENCE↗

Microstructural Characterization of Polymers by Positron Lifetime Spectroscopy

Positrons provide a versatile probe for monitoring microstructural features of molecular solids. In this paper, we report on positron lifetime measurements in two different types of polymers. The first group comprises polyacrylates processed on earth and in space. The second group includes fully-compatible and totally-incompatible Semi-Interpenetrating polymer networks of thermosetting and thermoplastic polyimides. On the basis of lifetime measurements, it is concluded that free volumes are a direct reflection of physical/electromagnetic properties of the host polymers.

Singh, Jag J.↗

Microstructural characterization of dissimilar welds between Incoloy 800H and 321 Austenitic Stainless Steel

In this work, the microstructural character of dissimilar welds between Incoloy 800H and 321 Stainless Steel has been discussed. The microscopic examination of the base metals, fusion zones and interfaces was characterized using an optical microscope and scanning electron microscopy. The results revealed precipitates of Ti (C, N) in the austenitic matrix along the grain boundaries of the base metals. Migration of grain boundaries in the Inconel 82 weld metal was very extensive when compared to Inconel 617 weldment. Epitaxial growth was observed in the 617 weldment which increases the strength and ductility of the weld metal. Unmixed zone near the fusion line between 321 Stainless Steel and Inconel 82 weld metal was identified. From the results, it has been concluded that Inconel 617 filler metal is a preferable choice for the joint between Incoloy 800H and 321 Stainless Steel. - Highlights: • Failure mechanisms produced by dissimilar welding of Incoloy 800H to AISI 321SS • Influence of filler wire on microstructure properties • Contemplative comparisons of metallurgical aspects of these weldments • Microstructure and chemical studies including metallography, SEM–EDS • EDS-line scan study at interface.

36 MATERIALS SCIENCE↗

Microstructural characterization of limestone exposed to heat with XRD, SEM and TG-DSC

Highlights: • The microstructure of limestone (25 °C–800 °C) was analyzed by XRD, SEM and TG-DSC. • The microstructural properties of the crystal are anisotropic in different crystal plane directions. • Microstructure controls the macroscopic properties of limestone. - Abstract: Limestone is a common rock used in many buildings and found in underground engineering projects. After exposure to heat, for example, the occurrence of fires, the stability of limestone structures is mostly affected, which may have safety repercussions. Therefore, the impact of thermal effects on the microstructure of limestone is investigated in this study, in which 8 groups of limestone samples are exposed to different temperatures (25 °C, 100 °C, 200 °C, 300 °C, 500 °C, 600 °C, 700 °C and 800 °C), after which X-ray diffraction, differential scanning calorimetry and scanning electron microscopy are carried out. The mineral composition and the microstructure of the samples are numerically modeled, in which the diffraction peaks, full width at half maximum, integral breadth, microstrain, average domain size and dislocation density are analyzed. The macroscopic properties obtained from the results in other works in the literature including porosity, compressive strength, damage coefficients and modulus of elasticity are also compared with the parameters above. The changes in the crystal structure of two minerals, calcite and dolomite, are found to be anisotropic in the different crystal plane directions. It is also found that the limestone microstructure affects the macroscopic properties. A temperature between 200 °C to 300 °C is the critical temperature at which both the macroscopic properties and macrostructure demonstrate significant changes.

36 MATERIALS SCIENCE↗

Hot Straining and Quenching and Partitioning of a TRIP-Assisted Steel: Microstructural Characterization and Mechanical Properties

Advanced high strength steels (AHSS), with yield strengths over 300 MPa and tensile strengths exceeding 600 MPa, are becoming more noticeable in vehicle manufacturing. A novel processing route of a TRIP-assisted steel was developed. Characterization and modelling techniques were used to establish correlations between processing, microstructure and mechanical properties. Quenching and partitioning (Q&P) and a novel process of hot straining (HS) and Q&P (HSQ&P) treatments have been applied to a TRIP-assisted steel in a Gleeble ®3S50 thermo-mechanical simulator. The heat treatments involved intercritical annealing at 800 oC and a two-step Q&P heat treatment with a partitioning time of 100 s at 400 oC. The effects of high-temperature isothermal deformation on the carbon enrichment of austenite, carbide formation and the strain-induced transformation to ferrite (SIT) mechanism were investigated. Carbon partitioning from supersaturated martensite into austenite and carbide precipitation were confirmed by means of atom probe tomography (APT). Austenite carbon enrichment was clearly observed in all specimens, and in the HSQ&P samples it was slightly greater than in Q&P, suggesting an additional carbon partitioning to austenite from ferrite formed by the SIT phenomenon. By APT, the carbon accumulation at austenite/martensite interface was clearly observed. The newly developed combined process is promising as the transformation induced plasticity can contribute to the formability and energy absorption, contributing to fill the gap of the third generation of high-strength steels.

Ariza, Edwan Anderson↗

Microstructural characterization of pipe bomb fragments

Recovered pipe bomb fragments, exploded under controlled conditions, have been characterized using scanning electron microscopy, optical microscopy and microhardness. Specifically, this paper examines the microstructural changes in plain carbon-steel fragments collected after the controlled explosion of galvanized, schedule 40, continuously welded, steel pipes filled with various smokeless powders. A number of microstructural changes were observed in the recovered pipe fragments: deformation of the soft alpha-ferrite grains, deformation of pearlite colonies, twin formation, bands of distorted pearlite colonies, slip bands, and cross-slip bands. These microstructural changes were correlated with the relative energy of the smokeless powder fillers. The energy of the smokeless powder was reflected in a reduction in thickness of the pipe fragments (due to plastic strain prior to fracture) and an increase in microhardness. Moreover, within fragments from a single pipe, there was a radial variation in microhardness, with the microhardness at the outer wall being greater than that at the inner wall. These findings were consistent with the premise that, with the high energy fillers, extensive plastic deformation and wall thinning occurred prior to pipe fracture. Ultimately, the information collected from this investigation will be used to develop a database, where the fragment microstructure and microhardness will be correlated with type of explosive filler and bomb design. Some analyses, specifically wall thinning and microhardness, may aid in field characterization of explosive devices.

36 MATERIALS SCIENCE↗

Microstructural Characterization of Pure Tin Produced by the Drop-on-Demand Technique of Liquid Metal Jetting

The microstructure–property relationship of a pure tin part built using the drop-on-demand technique of liquid metal jetting, a cost–effective alternative to selective laser-melting or sintering techniques, was determined. Here, the microstructure of the as-built tin is observed to have minimal stored strain, low dislocation density, few to no voids, and the presence of only the β-tin phase; concurrently, mechanical properties are shown to be identical to the traditionally manufactured tin.

36 MATERIALS SCIENCE↗

Microstructural Characterization of U-7Mo/Al-Si Alloy Matrix Dispersion Fuel Plates Fabricated at 500°C

The starting microstructure of a dispersion fuel plate will impact the overall performance of the plate during irradiation. To improve the understanding of the as-fabricated microstructures of U–Mo dispersion fuel plates, particularly the interaction layers that can form between the fuel particles and the matrix, scanning electron microscopy (SEM) and transmission electron microscopy (TEM) analyses have been performed on samples from depleted U–7Mo (U–7Mo) dispersion fuel plates with either Al–2 wt.% Si(Al–2Si) or AA4043 alloy matrix. It was observed that in the thick interaction layers, U(Al, Si)3 and U6Mo4Al43 were present, and in the thin interaction layers, (U, Mo) (Al, Si)3, U(Al, Si)4, U3Si3Al2, U3Si5, and possibly USi-type phases were observed. The U3Si3Al2 phase contained some Mo. Based on the results of this investigation, the time that a dispersion fuel plate is exposed to a relatively high temperature during fabrication will impact the nature of the interaction layers around the fuel particles. Uniformly thin, Si-rich layers will develop around the U–7Mo particles for shorter exposure times, and thicker, Si-depleted layers will develop for the longer exposure times.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Microstructural characterization of sulfur-doped Bi{sub 2}Te{sub 3} crystals

In this study, the detailed microstructure of sulfur-doped Bi{sub 2}Te{sub 3} and the distribution of sulfur dopants were investigated using X-ray diffraction (XRD) and transmission electron microscopy (TEM). XRD result indicates that the interplanar distances of Bi{sub 2}Te{sub 3} are shortened after introducing sulfur dopants. HRTEM reveals that the unit cell lengths along [001, 100] are decreased as a result of the substitution of Te by smaller S atoms on the anion lattice. XRD and HRTEM analysis suggest that the distortion of the crystal lattice in Bi{sub 2}Te{sub 3} is induced by doping sulfur. High annular angler dark field scanning electron microscopy (HAADF-STEM) image shows obvious contrast variations in the Te atomic columns, indicating that Te sites were unevenly substituted by S dopants. Te columns with least contrast intensity correspond to the preferential occupation sites of S atoms. The replacement of Te atoms by S can be attributed to the evaporated sulfur powder in the gas reaction procedure. The present work is not only contributed to obtain a better understanding of the distribution of sulfur dopants introduced by gas reaction, but also can help explore the structural-property relationship of sulfur-doped Bi{sub 2}Te{sub 3}. - Highlights: • Sulfur-doped Bi{sub 2}Te{sub 3} was synthesized through modified Bridgeman method. • The introduction of S dopants results in shortening the lattice spacing of Bi{sub 2}Te{sub 3}. • HRTEM analysis indicates that S was doped through substituting Te atoms instead of incorporating interstitially. • HAADF-STEM analysis shows that Te columns with least intensity correspond to the preferential occupation sites of S.

36 MATERIALS SCIENCE↗

Microstructural Characterization of AGR-2 TRISO-coated Particle Buffer, IPyC, and Buffer-IPyC Interfaces

Investigating the microstructural, mechanical, and chemical behaviors of Tristructural Isotropic (TRISO) fuel particles is vital for its qualification and use in advanced reactors. Central to the study of TRISO particles is understanding the silicon carbide (SiC) layer's ability to confine fission products, with failure mechanisms linked to chemical degradation following mechanical degradation of the buffer and IPyC layers. Research has been done to quantify the micro-tensile properties of the buffer, inner pyrolytic carbon (IPyC), and buffer-IPyC interlayer regions and their interactions within both irradiated and un-irradiated TRISO particles. Techniques such as atom probe tomography (APT) and transmission electron microscopy (TEM) have also been deployed to examine microstructural defects and fission product distribution in detail. The goal is to understand layer delamination, establish connections between microstructure and mechanical attributes, and inform computational predictions of fuel performance. This work may help refine predictive models of TRISO fuel behavior and facilitating its certification for use in advanced reactors.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Microstructural Characterization of Laser Powder Bed Fusion (L-PBF) Additively Manufactured Inconel 718 for Aerospace Application

Alloy 718 (Inconel 718) is used for aerospace applications because of its excellent corrosion resistance and mechanical properties. This alloy is particularly applicable in manufacturing components subjected to high temperatures in rocket engines, aero-engines, and gas turbines. Properties for this alloy when processing on systems from similar and different Laser Powder Bed Fusion (L-PBF) machines provide subtle differences due to process parameters, feedstock, and machine configurations. A series of sixteen L-PBF AM Inconel 718 geometric feature build plates have been evaluated for microstructure using optical microscopy. This study presents the details of the microstructure analysis concerning geometry and different machine platforms. Microstructural investigations of these samples included average grain width measurement for all the X-Y and Y-Z build layers and are accompanied by process parameters and powder characterization. The present work concludes with a discussion on the importance of captured differences among builds to understand the practical limitations among AM platforms.

Additive Manufacturing↗

Microstructural Characterizations of Two High Fluence Baffle-Former Bolts Retrieved from a Westinghouse Two-loop Downflow Type PWR

As one of the pressurized water reactor (PWR) internal components, baffle-former bolts (BFBs) are subjected to significant mechanical stress and neutron irradiation from the reactor core during the plant operation. Over the long operation period, these conditions lead to potential degradation and reduced load-carrying capacity of the bolts. In support of evaluating long-term operational performance of materials used in core internal components, the Oak Ridge National Laboratory (ORNL), through the Department of Energy (DOE), Office of Nuclear Energy, Light Water Reactor Sustainability (LWRS) Program, Materials Research Pathway (MRP), has harvested two high fluence BFBs from a commercial Westinghouse two-loop downflow type PWR. The two bolts of interest, i.e. bolts # 4412 and 4416, were withdrawn from service in 2011 as part of a preventative replacement plan. No identification of cracking or potential damage was found for these bolts during their removal in 2011. However, the bolts required a lower torque for removal from the baffle structure than the original torque specified during installation. Irradiation damage levels in the bolts range from 15 to 41 displacements per atom. The goal of this project is to perform detailed microstructural and mechanical property characterization of BFBs following in-service exposures. The information from these bolts will be integral to the LWRS program initiatives in evaluating end of life microstructure and properties. Furthermore, valuable data will be obtained that can be incorporated into model predictions of long term irradiation behavior and compared to results obtained from experimental reactor conditions

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

3D Microstructural Characterization of Uranium Oxide as a Surrogate Nuclear Fuel: Effect of Oxygen Stoichiometry on Grain Boundary Distributions

The initial microstructure of an oxide fuel can play a key role in its performance. At low burn-ups, the diffusion of fission products can depend strongly on grain size and grain boundary (GB) characteristics, which in turn depend on processing conditions and oxygen stoichiometry. Serial sectioning techniques using Focused Ion Beam were developed to obtain Electron Backscatter Diffraction (EBSD) data for depleted UO2 pellets that were processed to obtain 3 different oxygen stoichiometries. The EBSD data were used to create 3D microstructure reconstructions and to gather statistical information on the grain and GB crystallography, with emphasis on identifying the character (twist, tilt, mixed) for GBs that meet the Coincident Site Lattice (CSL) criterion as well as GBs with the most common misorientation angles. Data on dihedral angles at triple points were also collected. The results were compared across different samples to understand effects of oxygen content on microstructure evolution.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Microstructural characterization of Ti-6Al-4V metal chips by focused ion beam (FIB) and transmission electron microscopy (TEM)

The microstructure of the secondary deformation zone (SDZ) near the cutting surface in metal chips of Ti-6Al-4V formed during machining was investigated using focused ion beam (FIB) specimen preparation and transmission electron microscopy (TEM) imaging. Use of the FIB allowed precise extraction of the specimen across this region to reveal its inhomogeneous microstructure resulting from the non-uniform distribution of strain, strain rate, and temperature generated during the cutting process. Initial imaging from conventional TEM foil preparation revealed microstructures ranging from heavily textured to regions of fine grains. Using FIB preparation, the transverse microstructure could be interpreted as fine grains near the cutting surface which transitioned to coarse grains toward the free surface. At the cutting surface a 10 nm thick recrystallized layer was observed capping a 20 nm thick amorphous layer.

36 MATERIALS SCIENCE↗