Search NASA⌕ Search

SEARCH · Search NASA

Results for “molecular beam epitaxy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Acceptor and compensating donor doping of single crystalline SnO (001) films grown by molecular beam epitaxy and its perspectives for optoelectronics and gas-sensing

(La and Ga)-doped tin monoxide [stannous oxide, tin (II) oxide, SnO] thin films were grown by plasma-assisted and suboxide molecular beam epitaxy with dopant concentrations ranging from ≈ 5 × 10 18 to 2 × 10 21 cm -3 . In this concentration range, the incorporation of Ga into SnO was limited by the formation of secondary phases observed at 1.2 × 10 21 cm -3 Ga, while the incorporation of La showed a lower solubility limit. Transport measurements on the doped samples reveal that Ga acts as an acceptor and La as a compensating donor. While Ga doping led to an increase in the hole concentration from 1 × 10 18 -1 × 10 19 cm -3 for unintentionally doped (UID) SnO up to 5 × 10 19 cm -3 , La-concentrations well in excess of the UID acceptor concentration resulted in semi-insulating films without detectable n-type conductivity. Ab initio calculations qualitatively agree with our dopant assignment of Ga and La and further predict In Sn to act as an acceptor as well as Al Sn and B Sn as donors. These results show the possibilities of controlling the hole concentration in p-type SnO, which can be useful for a range of optoelectronic and gas-sensing applications.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Molecular beam epitaxy growth and optoelectronic properties of droplet-free lattice-matched GaInAsSbBi on GaSb with wavelength extension exceeding 5 μ m

GaInAsSbBi alloys are grown lattice-matched on GaSb by molecular beam epitaxy demonstrating smooth surface morphologies, >5 μm wavelength photoluminescence emission, and minority carrier lifetimes >1 μs. At a growth temperature of 400 °C, the Ga flux is systematically increased and the Bi flux systematically decreased to identify GaInAsSbBi growth conditions that yield smooth droplet-free surface morphologies. The minority carrier lifetime is evaluated using time-resolved photoluminescence, where it is observed that GaInAsSbBi samples exhibit minority carrier lifetimes comparable to their Bi-free GaInAsSb counterparts, on the order of 1.5–2 μs. The bandgap and Urbach energy are evaluated from steady-state photoluminescence to gain insight into the impact of the incorporated Bi. Coupled with Rutherford backscattering spectrometry measurements of the Bi mole fraction, bandgap reduction rates of 97 meV/% Bi in InAsSbBi and 150 meV/% Bi in GaInAsSbBi are observed, significantly higher than previous evaluations in InAsSbBi (35–55 meV/% Bi). Detailed comparisons of the Bi mole fraction, bandgap energy, and Urbach energy indicate that the bandgap reduction potential in this alloy system is inhibited by the formation of Bi clusters; however, the inclusion of Ga in the quinary alloy is effective in suppressing Bi's tendency to incorporate in clusters for Ga mole fractions >9%, maximizing the bandgap reduction per unit Bi and overall optoelectronic quality.

Atomic force microscopy↗
DOE OSTI2021

Hybrid molecular beam epitaxy growth of BaTiO 3 films

The ability to reproducibly synthesize thin films with precise composition and controlled structure is essential for fundamental study and mass production. Here, we demonstrate the hybrid molecular beam epitaxy (MBE) growth of epitaxial, single crystalline BaTiO3 films with different thicknesses on Nb-doped SrTiO3 substrates with atomically smooth surfaces. By combining scanning transmission electron microscopy, temperature-dependent high-resolution x-ray diffraction, reflection high-energy electron diffraction, and atomic force microscopy, we study the effect of growth conditions and the interplay between stoichiometry and epitaxial strain on the resulting structure. Furthermore, we demonstrate a close to bulk-like ferroelectric phase transition in thicker films and highlight the effect of strain on the phase transition temperature. This work establishes the hybrid MBE approach for the growth of heteroepitaxial BaTiO3 films on conducting substrates with scalable thickness and controlled stoichiometry.

Materials Science↗
NASA NTRS1988

Extremely low nonalloyed and alloyed contact resistance using an InAs cap layer on InGaAs by molecular-beam epitaxy

Extremely low alloyed and nonalloyed ohmic contact resistances have been formed on n-type InAs/In(0.53)Ga(0.47)As/In(0.52)Al(0.48)As structures grown on InP(Fe) by molecular-beam epitaxy. To insure the accuracy of the small contact resistances measured, an extended transmission line model was used to extrapolate contact resistances from test patterns with multiple gap spacings varying from 1 to 20 microns. For a 150-A-thick InAs layer doped to 2 x 10 to the 18th/cu cm and a 0.1-micron-thick InGaAs layer doped to 1 x 10 to the 18th/cu cm, a specific contact resistance of 2.6 x 10 to the -8th ohm-asterisk sq cm was measured for the nonalloyed contact, while a resistance less than 1.7 x 10 to the -8th ohm-asterisk sq cm is reported for the alloyed contact. Conventional Au-Ge/Ni/Au was used for the ohmic metal contact and alloying was performed at 500 C for 50 s in flowing H2. Using a thermionic field emission model, the barrier height at the InAs/InGaAs interface was calculated to be 20 meV.

Peng, C. K.↗
DOE OSTI2021

On the Development of Order and Interfaces during the Growth of Ultrathin La 2 CuO 4 Films by Molecular Beam Epitaxy

While the atomic structure of interfaces in complex oxide heterostructures created by epitaxial growth has been investigated extensively, few studies have been conducted on how interfaces form and restructure at the initial stage of film growth. The dynamic aspects of the growth behavior can strongly influence the final interfacial atomic structure, which may lead to the emergence of interface-specific properties, such as the rise of interfacial superconductivity between certain Ruddlesden-Popper oxide materials. In this report, the structural development of La2CuO 4 thin films grown by molecular beam epitaxy on a LaSrAlO 4 substrate is investigated by X-ray diffraction measurements with rapid scans over a volume of reciprocal space. This method provides far more detailed information on interface formation than traditional fixed-point measurements. The results show that the atomic structure of the interface becomes fully established after just a single unit cell of growth. Interestingly, restructuring continues to occur within the topmost half to one unit cell of the film during the deposition process. However, diffraction intensity oscillations from both reflection high-energy electron and X-ray measurements stabilize only after the growth of two unit cells, indicating that the growth front morphology continues to evolve until the start of the third unit cell. This multimodal investigation provides insights into the atomic processes taking place during layered oxide interface formation, including the dynamical rearrangement of LaO and CuO 2 layers. Such information is not only relevant to the engineering and optimization of functional layer structures but can also be critical for ultrathin films.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Growth of Nanometer-Thick γ-InSe on Si(111) 7 × 7 by Molecular Beam Epitaxy for Field-Effect Transistors and Optoelectronic Devices

γ-InSe is a semiconductor that holds promising potential in high-performance field-effect transistors and optoelectronic devices. Large-scale, single-phase γ-InSe deposition has proven challenging because of the difficulty in precise control of stoichiometry and the coexistence of different indium selenide phases. In this study, we demonstrate the wafer-scale combinatorial approach to map out the growth window as functions of the Se/In ratio and growth temperature for γ-InSe on the Si(111) 7 × 7 substrate in molecular beam epitaxy. X-ray diffraction (XRD) was used to identify the indium selenide phases, while atomic force microscopy revealed four distinct surface morphologies of γ-InSe, enabling a discussion of the growth mechanisms associated with each morphology. Cross-sectional atomic resolution scanning transmission electron microscopy confirmed that the film was of high crystalline quality and had nearly single-phase γ-InSe. In conclusion, our comprehensive study elucidates the In–Se phase map for thin film growth parameters, providing invaluable landmarks for the reproducible synthesis of high-quality γ-InSe layers.

36 MATERIALS SCIENCE↗
NASA NTRS1988

Growth of (111) GaAs on (111) Si using molecular-beam epitaxy

(111) GaAs layers have been grown epitaxially on (111) Si wafers, both on-axis as well as 3-deg off-axis towards the 1 -1 0 direction, using molecular-beam epitaxy. The grown layers have been characterized by scanning electron microscopy, X-ray diffraction, and transmission electron microscopy.

Radhakrishnan, G.↗
DOE OSTI2022

Molecular Beam Epitaxy (MBE) Growth of Model Cathodes to Study Interfacial Ion Diffusion

Lithium-ion batteries (LIBs) have been the focus of research for decades owing to their superior energy storage potential and wide range of applications. However, long-term stability issues still persist in LIB cathodes as the result of the formation of a solid electrolyte interface (SEI), structural transformations, or the loss of active cathode materials. In nanoscale cathodes, it is often impossible to isolate, let alone mitigate the causes of the observed capacity loss. Herein, a novel approach is presented to synthesizing LIB cathode model systems using thin-film molecular beam epitaxy (MBE). Specifically, 100 nm thick LiMn 2 O 4 (LMO) thin-film cathodes are grown on SrRuO 3 /SrTiO 3 (100) single-crystal substrates and characterized in their pristine and cycled states. The pristine thin films exhibit the electro-chemical cycling behavior and structural evolution previously seen in bulk LMO cathodes. The formation of surface-layer rocksalt MnO and spinel Mn 3 O 4 along with the mass-loss associated with the corrosion of active Mn ions is also reported. It is, therefore, demonstrated that these MBE-grown model systems can be used for detailed studies of their surface structures and the electrode/electrolyte interfacial evolution in LIB cathodes, leading to the development of materials for rechargeable batteries with higher capacity and better stability.

25 ENERGY STORAGE↗
DOE OSTI2024

Synthesis of Samarium Nitride Thin Films on Magnesium Oxide (001) Substrates Using Molecular Beam Epitaxy

Rare-earth nitrides are an exciting family of materials with a wide variety of properties desirable for new physics and applications in spintronics and superconducting devices. Among them, samarium nitride is an interesting compound reported to have ferromagnetic behavior coupled with the potential existence of p-wave superconductivity. Synthesis of high-quality thin films is essential in order to manifest these behaviors and understand the impact that vacancies, structural distortions, and doping can have on these properties. In this study, we report the synthesis of samarium nitride monocrystalline thin films on magnesium oxide (001) substrates with a chromium nitride capping layer using molecular beam epitaxy (MBE). We observed a high-quality monocrystalline SmN film with matching orientation to the substrate, then optimized the growth temperature. Despite the initial 2 nm of growth showing formation of a potential samarium oxide layer, the subsequent layers showed high-quality SmN, with semiconducting behavior revealed by an increase in resistivity with decreasing temperature. These promising results highlight the importance of studying diverse heteroepitaxial schemes and open the door for integration of rare-earth nitrides and transition metal nitrides for future spintronic devices.

36 MATERIALS SCIENCE↗
NASA NTRS1988

Electron beam source molecular beam epitaxial growth of analog graded Al(x)Ga(1-x)As ballistic transistors

A new method has been developed for the growth of graded band-gap Al(x)Ga(1-x)As alloys by molecular beam epitaxy which is based upon electron beam evaporation of the group III elements. The metal fluxes are measured and feedback controlled using a modulated ion gauge sensor. The system is computer controlled which allows precise programming of the Ga and Al evaporation rates. The large dynamic response of the metal sources enables growth of variable band-gap III-V alloys with arbitrary composition profiles. This new technique is demonstrated by synthesis of analog graded Al(x)Ga(1-x)As unipolar ballistic electron transistors.

Malik, Roger J.↗
DOE OSTI2025

Synthesis and Physical Properties of Manganese Chromium Nitride Thin Films Grown via Molecular Beam Epitaxy

Here, we demonstrate the ability to grow epitaxial thin films of manganese–chromium nitride (Mn x Cr 1–x N) across the entire composition range on magnesium oxide (MgO) (1 0 0) surfaces by molecular beam epitaxy. By independently controlling the ratio of the atomic fluxes of manganese and chromium, the compositional dependence of structural and electrical transport properties is determined. Soft X-ray absorption shows that the valence states of Cr( 3+ ) and Mn( 3+ ) remain identical among these MnCrN epitaxial films. The metallic transport behavior of binary manganese nitride (MnN) and chromium nitride (CrN) is suppressed in the ternary alloys. Changes in room temperature electrical resistivity of up to 100 times and 5 orders of magnitude at cryogenic temperatures are observed. This work expands the variety of nitride compounds available for epitaxial integration and could provide additional flexibility for the development of metal–semiconductor–insulator junctions for spintronic devices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Low-loss superconducting titanium nitride grown using plasma-assisted molecular beam epitaxy

Titanium nitride (TiN) is a known superconducting material that is attractive for use as passive components in superconducting circuits for both conventional and quantum information devices. In contrast to conventional synthesis techniques, here, plasma-assisted molecular beam epitaxy is reported to produce high-quality TiN on bare silicon wafers. Using a rf-plasma source to crack the nitrogen molecules and a conventional high-temperature effusion cell for titanium, TiN growth is completed under nitrogen-rich conditions. The growth and nucleation is monitored in situ, while the structure and composition are characterized using x-ray diffraction, atomic force microscopy, x-ray photoelectron spectroscopy, secondary ion mass spectroscopy, and scanning transmission electron microscopy. The stoichiometric TiN (111) films sit on an amorphous nitride layer with low impurity concentrations. The films superconduct with Tc=5.4 K, and coplanar waveguide resonators are fabricated with a small center width of 6 μm that demonstrate single-photon quality factors approaching 1M and high-power quality factors over 5M without observing saturation.

Richardson, C. J. K. (ORCID:0000000188175347)↗
DOE OSTI2020

Topological materials by molecular beam epitaxy

Topology appears across condensed matter physics to describe a wide array of phenomena which could alter, augment, or fundamentally change the functionality of many technologies. Linking the basic science of topological materials to applications requires producing high-quality thin films. This will enable combining dissimilar materials while utilizing dimensionality, symmetry, and strain to create or control the electronic phase, as well as platforms to fabricate novel devices. Yet, one of the longstanding challenges in the field remains understanding and controlling the basic material properties of epitaxial thin films. Here, we discuss how understanding the fundamental properties of topological materials grown by molecular beam epitaxy (MBE) is key to deepening the knowledge of the basic physics, while developing a new generation of topological devices. A focus will be on the MBE growth of intrinsic materials, creation, and control of superconducting and magnetic topological phases. Addressing these questions in the coming decade will undoubtedly uncover many surprises as new materials are discovered and their growth as high-quality thin films is refined.

2d quantum materials↗
DOE OSTI2025

Growth of tetragonal PtO by molecular-beam epitaxy and its integration into β-Ga 2 O 3 Schottky diodes

We demonstrate the epitaxial growth of tetragonal platinum monoxide (PtO) on MgO, TiO 2 , and β-Ga 2 O 3 single-crystalline substrates by ozone molecular-beam epitaxy. We provide synthesis routes and derive a growth diagram under which PtO films can be synthesized by physical vapor deposition. A combination of electrical transport and photoemission spectroscopy measurements, in conjunction with density functional theory calculations, reveal PtO to be a degenerately doped p-type semiconductor with a bandgap of E g ≈ 1.6 eV. Spectroscopic ellipsometry measurements are used to extract the complex dielectric function spectra, indicating a transition from free-carrier absorption to higher photon energy transitions at E ≈ 1.6 eV. Using tetragonal PtO as an anode contact, we fabricate prototype Schottky diodes on n-type Sn-doped β-Ga 2 O 3 substrates and extract Schottky barrier heights of ϕ B > 2.2 eV.

Hensling, Felix V. E. [Cornell Univ., Ithaca, NY (↗
DOE OSTI2022

Semi-metallic SrIrO 3 films using solid-source metal-organic molecular beam epitaxy

Perovskite SrIrO 3 films and its heterostructures are very promising, yet less researched, avenues to explore interesting physics originating from the interplay between strong spin–orbit coupling and electron correlations. Elemental iridium is a commonly used source for molecular beam epitaxy (MBE) synthesis of SrIrO 3 films. However, elemental iridium is extremely difficult to oxidize and evaporate while maintaining an ultra-high vacuum and a long mean free path. Here, we calculated a thermodynamic phase diagram to highlight these synthesis challenges for phase-pure SrIrO 3 and other iridium-based oxides. We addressed these challenges using a novel solid-source metal-organic MBE approach that rests on the idea of modifying the metal-source chemistry. Phase-pure, single-crystalline, coherent, epitaxial (001) pc SrIrO 3 films on (001) SrTiO 3 substrate were grown. Films demonstrated semi-metallic behavior, Kondo scattering, and weak antilocalization. Our synthesis approach has the potential to facilitate research involving iridate heterostructures by enabling their atomically precise syntheses.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Molecular beam epitaxy synthesis and electrical transport properties of the correlated kagome metal Ni⁢ 3 In

Ni 3 ⁢In is a paramagnetic intermetallic consisting of 𝐴⁢𝐵-stacked Ni-kagome networks. Correlated electron behaviors deviating from the Fermi-liquid form have recently been observed in Ni 3 ⁢In bulk single crystals, attributed to stabilization of a partially flat electronic band near the Fermi level. Synthesis of this system in thin-film form offers unique opportunities for tuning of materials that could aid in identifying the microscopic origin of the non-Fermi-liquid response and exploring the suspected quantum criticality therein. Here, we report the realization of (001)-oriented epitaxial thin films of Ni 3 ⁢In on single-crystal SrTiO 3 (111) substrates by molecular beam epitaxy. Via control of growth conditions, we fabricate high-quality films with quantum fluctuations strongly influencing the physical properties of the system. Analysis of the electrical transport response reveals that intrinsic spin fluctuations in Ni 3 ⁢In may account for the observed non-Fermi-liquid behavior. Such structures may facilitate driving Ni 3 ⁢In across a potential quantum critical phase transition and uncover the role of unusual flat bands in triggering correlated phenomena.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

Molecular beam epitaxy growth and characterization of GePb alloys

Pb based group-IV alloys such as GePb have been gaining interest as a potential alternative for infrared detectors, quantum materials, and high-speed electronic devices. Challenges remain in their growth due to the extremely low solid solubility of Pb in the Ge–Pb system. This paper reports molecular beam epitaxy growth of GePb alloy thin films on Ge(100) substrates. Effusion cells of Ge and Pb are used to control the flux ratio independently. The optimal substrate temperature is found to be near the thermocouple temperature of 300 °C based on the characterization of the grown films using high-resolution x-ray diffraction. A large change in the Ge:Pb beam equivalent pressure ratio from 10:1 to 1:1 results in only a minimal increase of the Pb composition from 0.74% to 2.84% as estimated from Raman spectroscopy and Rutherford backscattering spectrometry. Furthermore, scanning electron microscopy images show a large volume of Pb islands on the surface that form into either long trapezoidal rods or uniform droplets, with increasing Pb flux and growth time the density of Pb islands increased.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Advances in Molecular Beam Epitaxy Growth of Ultra-Wide Bandgap Ga2O3 Based Alloys

Gallium oxide (Ga2O3) is an emerging ultra-wide bandgap semiconductor material that has attracted attention for its potential to outperform existing SiC and GaN based devices operating at high breakdown voltages and high temperature. Isovalent alloying of In and Al in Ga2O3 provides the ability to engineer bandgap energy and strain of the material. Alloying with Al increases the bandgap energy and the theoretically achievable Baliga's figure of merit, a key measure of a material's ultimate performance limits for high power switching devices. Alloying with In introduces compressive strain and can be used to counteract the tensile strain of Al incorporation. The resulting (AlxGa1-x-yIny)2O3 alloy can be lattice-matched to commercially available Ga2O3 wafers and has a tunable bandgap energy greater than that of Ga2O3, 4.76 eV. Such lattice-matched material can be grown arbitrarily thick without the detrimental effects of elastic strain and relaxation, making it suitable for high voltage diodes and transistors. However, efforts to synthesize isovalent alloys are complicated by their tendency to phase separate into corundum Al2O3 or bixbyite In2O3. Literature reports of the quaternary (AlxGa1-x-yIny)2O3 are limited to <1% unintentional indium incorporation in In-catalyzed (AlxGa1-x)2O3. The primary limitation to quaternary growth is the limited incorporation of indium at elevated growth temperatures. This limited incorporation is due to both the volatility of indium oxide and Al and Ga cation exchange reactions which replace indium in In2O3. We report on the development of a novel high-throughput molecular beam epitaxy (MBE) technique to screen the growth conditions for the ternary alloy (InyGa1-y)2O3, and the application of these findings to the first successful synthesis of phase pure monoclinic (AlxGa1-x-yIny)2O3 by MBE. By leveraging the unique sub-oxide chemistry of Ga2O3 and in-situ monitoring of crystal properties by reflection high-energy electron diffraction (RHEED), a cyclical growth and etch-back method is developed and applied to rapidly characterize the (InyGa1-y)2O3 growth space. This cyclical method provides approximately 10x increase in experimental throughput and up to 46x improvement in Ga2O3 substrate utilization. Appropriate growth conditions for monoclinic (InyGa1- y)2O3 are identified by machine learning analysis of RHEED patterns and targeted growths are characterized ex-situ to confirm improved In incorporation. These growth conditions are then combined with established (AlxGa1-x)2O3 growth conditions to grow quaternary (AlxGa1-x-yIny)2O3 with Al mole fractions ranging from 1.4% - 24.4% and In mole fractions ranging from 3.1% to 15.5%. The chemical and optical properties of the alloys are investigated by XRD, XPS, and spectroscopic ellipsometry. A lattice-matched (AlxGa1-x-yIny)2O3 alloy is examined by 4D-STEM and the chemical and physical uniformity of Al and In incorporation are discussed.

alloy↗