Search NASA⌕ Search

SEARCH · Search NASA

Results for “optical films”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Compositional dependence of linear and nonlinear optical response in crystalline hafnium zirconium oxide thin films

Composition dependence of second harmonic generation, refractive index, extinction coefficient, and optical bandgap in 20 nm thick crystalline Hf 1– x Zr x O 2 (0 ≤ x ≤ 1) thin films is reported here. The refractive index exhibits a general increase with increasing ZrO 2 content with all values within the range of 1.98–2.14 from 880 nm to 400 nm wavelengths. A composition dependence of the indirect optical bandgap is observed, decreasing from 5.81 eV for HfO 2 to 5.17 eV for Hf 0.4 Zr 0.6 O 2 . The bandgap increases for compositions with x > 0.6, reaching 5.31 eV for Hf 0.1 Zr 0.9 O 2 . Second harmonic signals are measured for 880 nm incident light. The magnitude of the second harmonic signal scales with the magnitude of the remanant polarization in the composition series. Film compositions that display near zero remanent polarizations exhibit minimal second harmonic generation while those with maximum remanent polarization also display the largest second harmonic signal. The results are discussed in the context of ferroelectric phase assemblage in the hafnium zirconium oxide films and demonstrate a path toward a silicon-compatible integrated nonlinear optical material.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Microstructural, optical and electrical properties of CdS thin films grown by spray pyrolysis technique as a function of substrate temperature

In this research, nanocrystalline cadmium sulfide thin films were produced by the spray pyrolysis technique on glass substrates. The effects of substrate temperature in the range 400–550 °C on the structural, morphological, optical, and electrical properties of the thin films were investigated. The thin films have been characterized by investigating their X-ray diffraction, field emission scanning electron microscope (FE-SEM), and optical absorption (UV–Vis) measurements. X-ray analysis revealed that thin films were a polycrystalline structure with the hexagonal phase in all cases and by increasing in substrate temperature, crystallite size decreases, and dislocation density increases. The FE-SEM images showed that the surface of the thin films is uniform, homogeneous and without cracks. The average sizes of the grains are at the range of 210–235 nm. The obtained values for optical band gap have been in the range of 2.18–2.41 eV, where the value of optical band gap for the thin films decreases by increasing substrate temperature. The Urbach energies of the thin films increase as the substrate temperature is increased. When substrate temperature increased from 400 to 550 °C, electrical resistivity increased from 531 to 2817 Ω cm, carrier concentration decreased from 15.96 × 10{sup 14} to 3.71 × 10{sup 14} cm{sup −3}, Hall mobility decreased from 7.37 to 5.98 cm{sup 2}/V s. Hall effect analysis indicated that the thin films exhibited n-type conductivity.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2022

Intrinsic polarization-sensitive organic photodetector with self-assembled all-polymer heterojunction

Intrinsic polarization-sensitive photodetectors (IPPDs) have attracted considerable attention in recent years due to their simplicity in configuration, making them ideal candidates for compact and integrated polarization-sensitive sensing and imaging systems. Photoactive films with intrinsic optical anisotropy are necessary for IPPDs. This study reports an achievement of photoactive films based on all-polymer heterojunction films with in-plane optical anisotropy using a simple bottom-up self-assembly method. Both the donor (TQ1) and acceptor (N2200) polymers have the same spatial orientation with distinct anisotropy, approaching a dichroic ratio (DR) of 8. Polarization-sensitive light absorption is due to the uniaxially oriented polymer chains, which are dominated by lamellar packing with edge-on orientation. For IPPDs based on this anisotropic all-polymer heterojunction film, a photocurrent anisotropy was found with a polarized photocurrent ratio of 2.6. The detectivity of these IPPDs was found to be 1.9 × 1011 Jones (@ ∼600 nm, 0 V bias). Our work shows that oriented polymer donor–acceptor films fabricated using bottom-up self-assembly have great potential in applications, such as polarization detection.

Physics↗
DOE OSTI2022

Particle–hole asymmetry and quantum confinement effects on the magneto-optical response of topological insulator thin-films

Intrinsically broken symmetries in the bulk of topological insulators (TIs) are manifested in their surface states. Despite particle–hole asymmetry in TIs, it has often been assumed that their surface states are characterized by a particle–hole symmetric Dirac energy dispersion. In this work, we demonstrate that the effect of particle–hole asymmetry is essential to correctly describe the energy spectrum and the magneto-optical response in TIs thin-films. In thin-films of TIs with a substantial degree of particle–hole symmetry breaking, such as Sb 2 Te 3 , the longitudinal optical conductivity displays absorption peaks arising from optical transitions between bulk and surface Landau levels for low photon energies. The transition energies between the bulk and surface Landau levels exhibit clearly discernable signatures from those between surface Landau levels due to their distinct magnetic field dependence. Furthermore, bulk contributions to the magneto-optical conductivity in a TI thin-film are enhanced via one type of doping while being suppressed by the other. This asymmetric dependence on the type of doping aids in revealing the particle–hole asymmetry in TI thin-films.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Temperature-dependent optical constants of vanadium dioxide thin films deposited on polar dielectrics

Coating polar dielectrics with thin film vanadium dioxide (VO 2 ) enables one to exploit the temperature-dependent phase transition within VO 2 to actively tune and modulate surface phonon polaritons at mid-infrared. However, controlling the behavior of such systems requires intimate knowledge of the temperature-dependent optical constants of VO 2 , which depend greatly on the growth conditions and substrate material. Here, in this work, we accurately determine the complex optical constants of VO 2 on polar dielectrics across the insulator-to-metal phase transition (IMT) using only normal incident reflectance spectra by analyzing the reflectance with Kramers–Kronig relations and thin film Fresnel equations. This non-ellipsometry technique offers an advantage in determining the refractive index using a standard infrared spectrometer.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Engineering the Microstructure and Morphology of Explosive Films via Control of Interfacial Energy

Physical vapor deposition of organic explosives enables growth of polycrystalline films with a unique microstructure and morphology compared to the bulk material. This study demonstrates the ability to control crystal orientation and porosity in pentaerythritol tetranitrate films by varying the interfacial energy between the substrate and the vapor-deposited explosive. Additionally, variation in density, porosity, surface roughness, and optical properties is achieved in the explosive film, with significant implications for initiation sensitivity and detonation performance of the explosive material. Various surface science techniques, including angle-resolved X-ray photoelectron spectroscopy and multiliquid contact angle analysis, are utilized to characterize interfacial characteristics between the substrate and explosive film. Optical microscopy and scanning electron microscopy of pentaerythritol tetranitrate surfaces and fracture cross sections illustrate the difference in morphology evolution and the microstructure achieved through surface energy modification. X-ray diffraction studies with the Tilt-A-Whirl three-dimensional pole figure rendering and texture analysis software suite reveal that high surface energy substrates result in a preferred (110) out-of-plane orientation of pentaerythritol tetranitrate crystallites and denser films. Low surface energy substrates create more randomly textured pentaerythritol tetranitrate and lead to nanoscale porosity and lower density films. This work furthers the scientific basis for interfacial engineering of polycrystalline organic explosive films through control of surface energy, enabling future study of dynamic and reactive detonative phenomena at the microscale. Results of this study also have potential applications to active pharmaceutical ingredients, stimuli-responsive polymer films, organic thin film transistors, and other areas.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Detection of coherent optical phonons in a thin bismuth film by ultrafast electron diffraction

Coherent dynamics of lattice oscillations in a ∼20-nm-thick film obtained by thermal sputtering of bismuth is studied using ultrashort electron bunches synchronised with femtosecond laser pulses irradiating the sample. The Fourier analysis of ultrafast electron diffraction (UED) data shows that the observed modulation of the signal is due to the ensemble of modes corresponding to optical phonons with frequencies of approximately 3, 6 and 9 THz. A conclusion is made that these peaks correspond to the manifestation of the bismuth A{sub 1g} mode (three-terahertz peak), as well as its first and second overtones, which is probably due to quantum confinement in a 20-nm Bi nanostructure. The possibility of a detailed study of the quantum-size effect in bismuth with the help of a transmission UED is analysed. (paper)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2023

Structural, optical, and thermal properties of BN thin films grown on diamond via pulsed laser deposition

Heterostructures based on ultrawide-bandgap (UWBG) semiconductors (bandgap > 4.0 eV), such as BN and diamond, hold significant importance for the development of high-power electronics in the next generation. However, achieving in situ heteroepitaxy of BN/diamond or vice versa remains exceptionally challenging due to the complex growth kinetics involved. In this work, we grew BN thin film on (100) single-crystal diamonds using pulsed laser deposition and investigated its structural, magnetic, optical, and thermal properties. Throughout this study, the structural analyses confirmed the growth of BN films, which exhibited diamagnetic behavior at room temperature. Notably, the film demonstrated anisotropic refractive index characteristics within the visible-to-near-infrared wavelength range. The room-temperature cross-plane thermal conductivity of BN is 1.53 ± 0.77 W/mK, while the thermal conductance of the BN/diamond interface is 20 ± 2 MW/m 2 ⁢K. These findings have significant implications for a range of device applications based on UWBG BN/diamond heterostructures.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Creating Functional Oxynitride–Silicon Interfaces and SrNbO 2 N Thin Films for Photoelectrochemical Applications

Photoelectrochemical performance dependence upon absorption length, carrier diffusion length, and surface area of an oxynitride photoabsorber is investigated. How best to fabricate optical-quality thin films of bandgap-tunable oxynitrides is also discussed. We targeted the stoichiometric compound SrNbO 2 N as an optimal wide-bandgap photoabsorber (1.9 eV) for use with silicon (1.1 eV) in a tandem structure photoelectrochemical cell. Preparation of perovskite oxynitrides at high-temperature as isolated powders is often straightforward, but it is difficult to integrate them as thin films in tandem junction devices with low-temperature materials. Here we develop the first method to prepare optical-quality SrNbO 2 N thin-films of tunable thickness and roughness on single-crystal silicon substrate. This achievement required an interfacial layer of ultra-thin TaN to be used as a barrier to reduce the inter-diffusion of silicon and oxygen during oxynitride syn-thesis. We produced a variety of SrNbO 2 N film thicknesses (20-440 nm) on n + -Si(100) surfaces. Roughness factor (0.14-21) scaled with thickness. The intrinsic photoelectrochemical activity of these devices was evaluated using a low-barrier sacrificial electron donor. Photocurrent density and photovoltage revealed a significant (and non-linear) dependence on film thickness and roughness. Furthermore, absorption length, carrier diffusion length, and surface area were each found to play key roles. Balancing these is required for optimally performing devices.

08 HYDROGEN↗
DOE OSTI2025

Morphology and property tuning in ZnO–Ni hybrid metamaterials in vertically aligned nanocomposite (VAN) form

ZnO thin films have attracted significant interest in the past decades owing to their unique wide band gap properties, piezoelectric properties, non-linearity and plasmonic properties. Recent efforts have been made in coupling ZnO with secondary phases to enhance its functionalities, such as Au–ZnO nanocomposite thin films with tunable optical and plasmonic properties. In this work, magnetic nanostructures of Ni are incorporated in ZnO thin films in a vertically aligned nanocomposite (VAN) form to couple magnetic and plasmonic response in a complex hybrid metamaterial system. Nickel (Ni) is of interest due to its ferromagnetic and plasmonic properties along with gold (Au) which is also plasmonic. Therefore, two approaches, namely, tuning of the deposition pressure and use of a ZnO–Au seeding layer have been attempted to achieve unique Ni nanostructures in addition to tuning of the microstructure. Together, both approaches demonstrate a range of microstructures such as core–shell, nanodisk, nanocup, and nanocube-like morphologies not previously attempted. Additionally, there is effective tuning of properties. Specifically, the seeding layer thickness causes hyperbolic behavior as well as redshift in the surface plasmon resonance (SPR) wavelength. The addition of the ZnO–Au seeding layer directly influences the optical properties. Plus, regardless of the different approaches, the films demonstrate magnetic anisotropy based on the composition and microstructure of the film which impacted the saturation magnetization and coercivity. This study demonstrates the potential of ZnO-based complex hybrid metamaterials with coupled electro-magneto-optical properties for integrated photonic devices.

Bhatt, Nirali A. [Purdue Univ., West Lafayette, IN↗
DOE OSTI2020

Enhancement of Optical Efficiency of CSP Mirrors for Reducing O&M Cost via Near-Continuous Operation of Self-Cleaning Electrodynamic Screens (EDS). Final Report

Over the past decade, techno-economical advancements in solar energy systems, particularly the improvement in the conversion efficiency of PV modules made with mono-crystalline silicon solar cells from 12% to 20%, as well as the cost reduction in manufacturing by a factor of about 10%, have made it possible to achieve a levelized cost of electricity (LCOE) in PV plants that is comparable to, or less than, the cost of deriving electricity from fossil fuels. Operating PV plants in mid-latitude sun-belt regions, where the solar irradiance level is highest, provides a high annual energy-yield (kWh/kWp) due to two factors: (1) the availability of predictable high solar irradiance throughout the year with the fewest interruptions in solar flux from clouds and rain, and (2) the increased conversion efficiency of crystalline solar cells, as recombination loss has decreased with increased intensity of the sunlight that illuminates the silicon solar cells. Semi-arid and desert regions, however, are plagued by high atmospheric dust concentrations and frequent sand storms. The deposition of a layer of dust on the optical surfaces of solar collectors such as PV modules and concentrating mirrors reduces the transmission efficiency of sunlight that actually reaches the solar cells or receivers, resulting in high energy-yield soiling loss. There are two major cost components to operating a solar plant: (1) installation costs, and (2) operation-and-maintenance (O&M) costs. There is no fuel cost; hence operating a solar plant in a semi-arid or desert region provides high returns on investment if soiling losses are mitigated via efficient cleaning methods and optimized cleaning frequency. If solar collectors are not cleaned, the accumulation of dust layers on solar collectors may cause the operation of such plants in arid regions to become economically unviable. Washing solar collectors with water and detergent, as is most commonly done now, is an efficient method for cleaning. The conventional approach in utility-scale solar plants is to use a large truck with a water tank and pump system for spraying deionized water on the surface of the solar collectors. Robotic cleaning with brushes, used for many solar plants, requires lesser water for cleaning. The water consumed using semi-automated cleaning of PV modules in utility-scale solar plants is approximately 2 liters/m 2 per cleaning cycle. The total optical surface area of the solar collectors in 1 TW-scale solar installation will be more than 3 × 109 m 2 ; hence an enormous amount of water be needed for cleaning. There simply is not enough fresh water in the sun-belt areas of the world for predicted cleaning needs. In solar power plants, the estimated cost of cleaning solar collectors includes expenses related to the equipment used, labor, cost of transportation of water, the energy required for cleaning, plus ancillary costs whereas the cost of water is not considered. The water used is obtained from sources located close to plant sites, unmindful of the environmental and societal impact as the power plants are oftentimes located in regions that face severe drought. This practice is very similar to the cost calculations in deriving the levelized cost of electricity (LCOE) in conventional power plants based on burning fossil fuel such as coal and gas, while disregarding the cost of climate change and health effects. Unless a water-free or low-water cleaning method is established, the expansion of solar plants may lose public support in areas suffering long intervals of drought. The goal of this research project has been the development and application of the Electrodynamic Screen (EDS) as a means for a water-free, scalable cleaning process applicable to solar-power installations, including rooftop applications. We describe here the development of an EDS film-based cleaning process as an emerging method for use on PV modules, parabolic troughs, and heliostats. This report aims to show the feasibility of integrating or retrofitting EDS films onto the optical surfaces of solar collectors (both PV and CSP) while maintaining high transmission or reflection efficiency. The cleaning action provided by the EDS film is an active method to remove dust deposits by electrodynamic force. Current lab-scale prototype EDS films, retrofitted onto solar panels and mirrors, have shown to be capable of maintaining optical transmission or specular-reflection efficiencies higher than 90% of initial values under clean conditions. The optical surfaces of solar collectors laminated with EDS films can remove more than 90% of deposited dust when the EDS is activated for less than two minutes. As an electrodynamic dust removal process, the EDS film-based method is designed primarily for the removal of dust in solar installations located in semi-arid and desert areas, where the atmosphere is often dry and dusty and rainfall is infrequent. While EDS film application minimizes water consumption and facilitates cleaning as frequently as needed, it has limitations in removing contaminants such as soot, organic pollutants deposited as fine films on the surface, and bird droppings. The dust removal efficiency of the EDS is maximum at relative humidity RH is 40 to 50% and decreases at when RH > 65%. Many solar plant sites undergo diurnal and seasonal cycles of high ambient, early afternoon temperatures and an RH that reaches the dew point early in the morning. These variations in atmospheric conditions do not limit the operation of the EDS film. This report presents a brief review of the progress and the potential of EDS film technology for mitigating the impact of dust on solar collectors via water-free cleaning, as well as current technical challenges regarding efficiency and durability. Our experimental data on the performance of EDS films show that: (1) the dust-removal efficiency (DRE) can reach levels higher than 90%, (2) the specular reflectivity (SR) of EDS film-laminated second-surface mirrors reach levels in excess of 90%, (3) the specular reflectivity restoration (SRR) can exceed 90%, (4) the output-power restoration (OPR) of PV modules can exceed 95%, and (5) the optical transmission efficiency (TE) of the EDS films can be greater than 90%. Working with Sandia National Laboratories (NM), Corning Research and Development Corporation (NY), Eastman Kodak (NY), Tomark-Worthen Industries (NH), and EDS Chile SPA (Chile), we have produced EDS film-laminated PV modules and demonstrated their self-cleaning functions without requiring water. We have demonstrated that the operational range of EDS films will cover the expected ambient temperature of solar fields at RH cycling varying from 20 to 95% as long as the EDS films are activated in the RH range 20 to 50%. (Typical solar-field climates in deserts and semi-arid lands often reach near dew point in coastal areas.) Our experiments on the application of hydrophobic-fluorinated nanoparticle coatings on EDS film surfaces show that the EDS operational range can be extended to higher RH levels that approach the dew point. At Eastman Kodak, as one of our industrial partners, we were able to establish a process for manufacturing EDS films using flexographic printing of the electrodes onto transparent polymer films. This process utilizes an existing manufacturing line at Eastman Kodak that allows fabrication of medium-scale EDS films (26 cm × 30 cm). The manufacturing process has the capacity to produce EDS films at high production speeds. The medium-scale EDS films that have been printed at Kodak were evaluated in the lab at Boston University. The EDS films produced at Kodak were laminated at Tomark-Worthen using an industrial scale vacuum laminator to produce EDS film stacks, which can be affixed onto the optical surfaces of PV modules or concentrating mirrors. The EDS film stack consists of the EDS films that have Willow® Glass (WG) which has a thickness of 100 μm as the front surface. The WG sheets obtained from Corning Research and Development Corporation are customized in size and shape to cover the active area of the EDS films. The back surface of the EDS film stack is integrated onto the optical surface of the solar panel or mirror using optically clear adhesive (OCA) films or silicone adhesives. The OCA films (thickness 25 μm) are produced by 3M. The EDS film stacks have the architecture: WG/OCA/EDS Film/OCA/ over PV module or solar mirror. The power-supply units needed for activating the electrodes of the EDS film were designed and produced at Boston University. These power supply units provide three-phase, 1.2 kV voltage pulses at a very low current (micro-ampere) level and at a low frequency (≈ 5 Hz). The voltage pulses are applied to the electrodes in a sequence such that the train of pulses resembles a unidirectional traveling wave of electrical field on the surface of the EDS film. The dust particles on the surface become charged electrostatically and are levitated by the Coulomb force. The lateral sweeping action of the traveling electric field created by the three-phase voltages pulses then sweeps the dust off the surface. The energy consumed by the EDS electrodes is less than 0.2 Wh/m 2 /cleaning cycle, enabling energy-efficient restoration of output power (OPR) of PV module or specular reflectivity restoration (SRR) for solar mirrors. The EDS system consists of (1) an EDS film stack laminated onto the solar collectors, (2) connection of the EDS film to its power supply unit and (3) Interconnection of the power supply to PV modules or solar mirrors. Design, construction and assessment of field-testing units that have EDS stack laminated PV modules for evaluating the performance of the EDS films in solar fields is being carried out at BU. Our progress under this project, aimed at the advancement of EDS film technology, has reached DOE Technology Readiness Level (TRL) 6. Based on the extensive laboratory evaluations and limited field trials, as well as contacts with potential users, we believe that the technology has reached its commercial stage. We are conducting a cost analysis using the National Renewable Energy Laboratory (NREL) System Advisory Model (SAM) and are preparing for field trials of EDS films in different solar fields in the US, Chile, India and in the Middle East. A brief description of EDS film performance, construction and testing of the field-test unit, autonomous operation of the field-test unit for evaluating EDS performance in increasing energy yield, associated revenue savings, and water conservation is presented.

14 SOLAR ENERGY↗
DOE OSTI2026

Enhanced quantum efficiency from optical interference in alkali antimonide photocathodes: Modeling and experimental results

We present measurements of enhanced quantum efficiency (QE) in thin film alkali antimonide photocathodes from optical interference in the cathode-substrate multilayer. Modulations in the spectral response are observed over a range of visible wavelengths and are shown to increase the QE by more than a factor of two at specific wavelengths. We present a model describing the QE modulations based on the three step photoemission process incorporating cases of both constant density of states and density functional theory-derived density of states and show that the calculated results are in good agreement with the measurements. Model predictions demonstrate that QE can be enhanced by more than a factor of 5 by optimization of cathode and substrate layer thicknesses. Additionally, these calculations reveal that optical interference can yield higher quantum efficiencies in thin films compared to thick, optically dense films. We model the QE vs excitation wavelength of multiple alkali antimonide compounds at different thicknesses. We then discuss the advantages of this interference effect for electron accelerators.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2023

Tuning Organic Semiconductor Packing and Morphology through Non-equilibrium Solution Processing (Final Report)

Organic semiconductors (OSCs) are a promising candidate to produce low-cost, large area, and flexible electronics. There has previously been successful development of organic field effect transistors (OFETs), photovoltaics (OPV), and bioelectronics using OSCs. Solution processing of these materials allows for the fabrication of large-area devices in the kinetic crystallization regime. The charge transport capabilities have been shown to depend on the morphology and molecular packing of the OSC within thin films. Our hypothesis is that solution processing conditions may significantly impact OSC morphology and as a result the charge transport. Therefore, this work has focused on obtaining a fundamental understanding of the morphology and molecular packing of OSCs for optimal device performance. Through our work, we have gained a better understanding of how these structural conditions were influenced by the solution processing conditions. Our studies have led to a more systematic understanding of the various parameters that impact OSC morphology. Solution processing leads to non-equilibrium films, thus allowing for the formation of diverse morphologies that are inaccessible by other fabrication methods. Previously, our group has focused on tuning the morphology of small-molecular OSCs [53, 55-57]. However, little work had been devoted to polymer OSCs. There was a lack of detailed studies characterizing the solution-state of polymer OSCs in terms of their conformation, degree of entanglement, polymer aggregation, and chain relaxation dynamics. The solution state properties are also likely to be influenced by the rigidity and molecular weight of the polymer OSCs investigated. Thus, we have focused our attention on gaining a better insight of polymer OSC films and solution processing methods. Through this proposal, our approach is to investigate the correlation between solution-state properties and the morphology of the resulting polymer OSC films. We worked three specific aims: investigate the effects of 1) polymer OSC solution-state properties on final film morphology; 2) molecular additives on the solution-state and final film properties; 3) controlled pre-aggregation in the solution-state in the final film morphology. More rigid and planar polymer backbones should promote interchain charge transport and more efficient interchain hopping between polymer chains. Through tailoring the polymer backbone, polymer sidechains, and molecular weight, we expected the altered solution-state properties to affect the final film morphology. In addition, reducing the entanglements and promoting chain alignment will likely prevent charge carrier trapping through conformation disorders. We thus studied different mechanisms, such as molecular additives, to reduce entanglements in solution. Devices fabricated from these solutions were expected to have improved charge transport abilities. In addition to tailoring the solution-state characteristics of the polymer OSCs, we investigated the effect of solution processing methods on the molecular packing and morphology of polymer OSC films. Two main solution processing techniques, e.g., spin-coating and solution shearing, were employed to fabricate OFETs. Spin coating was employed to prepare OSC films, which produce isotropic films. This technique creates several parameters to tune such as spin coating speed, acceleration, and time. Additionally, our research group developed the solution shearing method, which consists of the solution initially sandwiched between two plates. By sliding the top plate, the solution front is exposed and drying begins. This technique allows for the creation of aligned large crystalline domains. Solution shearing consists of different processing parameters which can affect the final morphology, such as shearing speed, substrate temperature and temperature gradient, distance between both plates, and the tilt angle of the top plate. Due to the complexity of the polymer systems investigated, numerous techniques were employed to characterize the polymer OSC solution state and films. All the materials were characterized using the DOE supported synchrotron X-ray scattering facilities at the Stanford Synchrotron Radiation Lightsource (SSRL). Using grazing incidence X-ray scattering (GIXS) and Near Edge X-ray Absorption Fine Structure (NEXAFS) techniques, the crystalline structure and molecular orientations of the thin films were measured. Optical absorption (UV-Vis) spectroscopy was employed to determine the aggregation state in solution and films of the polymer systems. Polarized UV-Vis also allowed for the determination of the relative degree of polymer chain alignment for solution sheared films. Additionally, various other techniques were used to investigate other properties within the film, such as atomic force microscopy (AFM) and solution rheology. Finally, the device performance is quantified through the fabrication and characterization of OFETs, which will highlight the effects of morphology on charge transport.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Structural, Optical and Mechanical Properties of Nanocrystalline Molybdenum Thin Films Deposited under Variable Substrate Temperature

Molybdenum (Mo), which is one among the refractory metals, is a promising material with a wide variety of technological applications in microelectronics, optoelectronics, and energy conversion and storage. However, understanding the structure–property correlation and optimization at the nanoscale dimension is quite important to meet the requirements of the emerging nanoelectronics and nanophotonics. In this context, we focused our efforts to derive a comprehensive understanding of the nanoscale structure, phase, and electronic properties of nanocrystalline Mo films with variable microstructure and grain size. Molybdenum films were deposited under varying temperature (25–500 °C), which resulted in Mo films with variable grain size of 9–22 nm. The grazing incidence X-ray diffraction analyses indicate the (110) preferred growth behavior the Mo films, though there is a marked decrease in hardness and elastic modulus values. In particular, there is a sizable difference in maximum and minimum elastic modulus values; the elastic modulus decreased from ~460 to 260–280 GPa with increasing substrate temperature from 25–500 °C. The plasticity index and wear resistance index values show a dramatic change with substrate temperature and grain size. Additionally, the optical properties of the nanocrystalline Mo films evaluated by spectroscopic ellipsometry indicate a marked dependence on the growth temperature and grain size. This dependence on grain size variation was particularly notable for the refractive index where Mo films with lower grain size fell in a range between ~2.75–3.75 across the measured wavelength as opposed to the range of 1.5–2.5 for samples deposited at temperatures of 400–500 °C, where the grain size is relatively higher. The conductive atomic force microscopy (AFM) studies indicate a direct correlation with grain size variation and grain versus grain boundary conduction; the trend noted was improved electrical conductivity of the Mo films in correlation with increasing grain size. The combined ellipsometry and conductive AFM studies allowed us to optimize the structure–property correlation in nanocrystalline Mo films for application in electronics and optoelectronics.

36 MATERIALS SCIENCE↗