Results for “packet analysis” — Page 6

DOE OSTI2025

Dual-band Ion-scale Waves in the Solar Wind: Statistical Properties and Comparison with Single-band Ion-scale Waves

We present a comprehensive statistical analysis of ion-scale waves including dual-band ion-scale waves (DBIWs) observed by the Parker Solar Probe in the solar wind. DBIWs are characterized by the simultaneous occurrence of distinct left- and right-handed polarized wave packets at higher and lower frequencies, respectively, in the spacecraft frame, implying the presence of bidirectionally propagating L-mode waves. We identify and compare DBIWs to single-band ion-scale waves (SBIWs) and investigate their spatial distributions, background magnetic field conditions, and associated inertial range turbulence characteristics. We find that DBIWs exhibit a strong preferential occurrence at heliocentric distances between 0.2 and 0.25 au (equivalently 43 and 54 R S ) in contrast to SBIWs, the occurrence rate of which peaks closer to the Sun and decreases with the heliocentric distance. DBIWs are also preferentially observed under conditions of strong Alfvénic turbulence, characterized by low magnetic compressibility and perpendicular-dominant fluctuations. These findings support a scenario in which stochastic ion heating via sufficiently large perpendicular Alfvénic fluctuation generates the ion temperature anisotropies required to excite bidirectional ion cyclotron waves. This work advances our understanding of kinetic wave generation in the solar wind and its connection to large-scale turbulence.

79 ASTRONOMY AND ASTROPHYSICS↗

DOE OSTI2021

Performance of DSRC V2V Communication Networks in an Autonomous Semi-Truck Platoon Application

Autonomy for multiple trucks to drive in a fixedheadway platoon formation is achieved by adding precision GPS and V2V communications to a conventional adaptive cruise control (ACC) system. The performance of the Cooperative ACC (CACC) system depends heavily on the reliability of the underlying V2V communications network. Using data recorded on precision-instrumented trucks at both ACM and NCAT test tracks, we provide an understanding of various effects on V2V network performance: Occlusions - non-line-of-sight (NLOS) between the Tx and Rx antenna may cause network signal loss. Rain - water droplets in the air may cause network signal degradation. Antenna position - antennas at higher elevation may have less ground clutter to deal with. RF interference - interference may cause network packet loss. GPS outage - outages caused by tree cover, tunnels, etc. may result in degraded performance. Road curvature - curves may affect antenna diversity. Road grade - antenna may have limited vertical coverage. Our results, which include multiple plots and graphs and their analysis, build on those reported by others and could be of interest to researchers, practitioners, and end-users in the broader autonomous-connected vehicle community.

V2V communications, GPS, truck platoon, semi-auton↗

NASA NTRS2017

Multi-Objective Reinforcement Learning-Based Deep Neural Networks for Cognitive Space Communications

Future communication subsystems of space exploration missions can potentially benefit from software-defined radios (SDRs) controlled by machine learning algorithms. In this paper, we propose a novel hybrid radio resource allocation management control algorithm that integrates multi-objective reinforcement learning and deep artificial neural networks. The objective is to efficiently manage communications system resources by monitoring performance functions with common dependent variables that result in conflicting goals. The uncertainty in the performance of thousands of different possible combinations of radio parameters makes the trade-off between exploration and exploitation in reinforcement learning (RL) much more challenging for future critical space-based missions. Thus, the system should spend as little time as possible on exploring actions, and whenever it explores an action, it should perform at acceptable levels most of the time. The proposed approach enables on-line learning by interactions with the environment and restricts poor resource allocation performance through virtual environment exploration. Improvements in the multiobjective performance can be achieved via transmitter parameter adaptation on a packet-basis, with poorly predicted performance promptly resulting in rejected decisions. Simulations presented in this work considered the DVB-S2 standard adaptive transmitter parameters and additional ones expected to be present in future adaptive radio systems. Performance results are provided by analysis of the proposed hybrid algorithm when operating across a satellite communication channel from Earth to GEO orbit during clear sky conditions. The proposed approach constitutes part of the core cognitive engine proof-of-concept to be delivered to the NASA Glenn Research Center SCaN Testbed located onboard the International Space Station.

space archtiecture↗

NASA NTRS2017

Multi-Objective Reinforcement Learning-based Deep Neural Networks for Cognitive Space Communications

Future communication subsystems of space exploration missions can potentially benefit from software-defined radios (SDRs) controlled by machine learning algorithms. In this paper, we propose a novel hybrid radio resource allocation management control algorithm that integrates multi-objective reinforcement learning and deep artificial neural networks. The objective is to efficiently manage communications system resources by monitoring performance functions with common dependent variables that result in conflicting goals. The uncertainty in the performance of thousands of different possible combinations of radio parameters makes the trade-off between exploration and exploitation in reinforcement learning (RL) much more challenging for future critical space-based missions. Thus, the system should spend as little time as possible on exploring actions, and whenever it explores an action, it should perform at acceptable levels most of the time. The proposed approach enables on-line learning by interactions with the environment and restricts poor resource allocation performance through virtual environment exploration. Improvements in the multiobjective performance can be achieved via transmitter parameter adaptation on a packet-basis, with poorly predicted performance promptly resulting in rejected decisions. Simulations presented in this work considered the DVB-S2 standard adaptive transmitter parameters and additional ones expected to be present in future adaptive radio systems. Performance results are provided by analysis of the proposed hybrid algorithm when operating across a satellite communication channel from Earth to GEO orbit during clear sky conditions. The proposed approach constitutes part of the core cognitive engine proof-of-concept to be delivered to the NASA Glenn Research Center SCaN Testbed located onboard the International Space Station.

space archtiecture↗

DOE OSTI2023

EmSense: A High-Resolution Emulated Sensor for Experiments with the Smart Grid and Distributed Ledger Technology

This work involves the development of a device - EmSense (“Emulated Sensor”) - that emulates a high-resolution sensor for a power grid. The device collects raw current and voltage sensor data which derive from ORNL's signature library. This library is a dataset that ORNL curates from many different sources that include power systems from various utilities. The EmSense packages the data from the library in the form of IEC 61850 Sampled Value (SV) packets and then broadcasts these SV packets on the network. In another mode, EmSense can generate artificial sinusoidal data that appears as waveforms for voltage and current signals. EmSense has an internal algorithm for determining the period of a signal based on the data so that the period can be specified as a variable in the IEC 61850 packets. The purpose of EmSense is to allow for experimentation with the Dark Net Infrastructure where a variety of power line sensors must be represented along with their typical communication traffic. The EmSense device was developed in coordination with the software for receiving and processing the packets in the Distributed Ledger Technology (DLT) framework of the DarkNet Project. This receiving software must have a methodology for dealing with information of high velocity, variety, and volume. Experimenting with EmSense facilitates the development of such software. The results showed that the DLT framework and the trust-anchoring approach managed to process a large flow of traffic even with up to six instances of EmSense device broadcasting data. This was achieved without overfilling packet queues in the memory of the actual hardware of the DLT devices or causing the Central Processing Unit (CPU) of the hardware to be overwhelmed. The DLTs were also able to store the data in a compact and useful form for later analysis and archival purposes.

Werth, Aaron↗

NASA NTRS1990

Analysis of exhaustive limited service for token ring networks

Token ring operation is well-understood in the cases of exhaustive, gated, gated limited, and ordinary cyclic service. There is no current data, however, on queueing models for the exhaustive limited service type. This service type differs from the others in that there is a preset maximum (omega) on the number of packets which may be transmitted per token reception, and packets which arrive after token reception may still be transmitted if the preset packet limit has not been reached. Exhaustive limited service is important since it closely approximates a timed token service discipline (the approximation becomes exact if packet lengths are constant). A method for deriving the z-transforms of the distributions of the number of packets present at both token departure and token arrival for a system using exhaustive limited service is presented. This allows for the derivation of a formula for mean queueing delay and queue lengths. The method is theoretically applicable to any omega. Fortunately, as the value of omega becomes large (typically values on the order of omega = 8 are considered large), the exhaustive limited service discipline closely approximates an exhaustive service discipline.

Peden, Jeffery H.↗

DOE OSTI2025

A Secondary Control Framework for Microgrid Interoperability With Vendor-Agnostic Grid-Forming Units: Design, Implementation, and Demonstration via Large-Scale Hardware Setup

The reliable operation of islanded microgrids increasingly depends on secondary controls that restore voltage and frequency to nominal values and ensure accurate active and reactive power sharing. Centralized secondary control architectures achieve high accuracy through global coordination at the cost of single-point failures and limited scalability compared with decentralized/distributed approaches. But a critical gap remains in addressing the interoperability and vendor-agnostic operation of secondary controls in real-world microgrids where heterogeneous diesel generator(s) and grid-forming (GFM) inverter(s) from multiple manufacturers always coexist. Practical and vendor-agnostic interoperability guidelines for the secondary control architecture of microgrids with multiple GFM units have not yet been developed; therefore, this paper proposes an interoperable and vendor-agnostic secondary control framework that operates seamlessly across GFM units from different vendors without relying on proprietary controls and protocols, hardware, or lock-ins. The framework leverages existing communication infrastructures (e.g., Modbus TCP/IP) to enable cost-effective deployment while addressing practical challenges, such as packet loss and quantization errors. Mitigation strategies-including data averaging, situational event-triggered control, and finite-iteration execution-are introduced to enhance reliability under real-world conditions. A generalized modeling and design framework is also presented, supported by robustness analysis to demonstrate independence from vendor-specific implementations. The proposed framework is validated through a large-scale hardware demonstration using a 3-$\phi$, 480-V, 60-Hz, 713-kVA laboratory hardware microgrid involving a heterogeneous diesel generator and multiple GFM inverters, showcasing its effectiveness in achieving stable voltage and frequency restoration and accurate power sharing under practical constraints. The results highlight the framework's potential as a scalable and practical solution for next-generation microgrids requiring openness, standard framework, and interoperability.

24 POWER TRANSMISSION AND DISTRIBUTION↗

NASA NTRS2008

Moving Away from Ones and Zeros, Designing a Ground Data System Based on Higher Levels of Abstraction

Previous JPL ground systems have been designed with the Ground Data System (GDS) engineer in mind. The focus on these systems has been on packaging and delivery of low level information (frames, packets, telemetry values) to the end user. It was not that long ago when project teams would be huddled over a workstation, examining crude displays of telemetry bits organized in various ways, trying to determine the status of a spacecraft. Understanding the data often required additional levels of GDS expertise, or worse, transformation of the raw data into alternative formats followed by ingestion into other tools so that the data became meaningful. The primary focus was often to answer these types of questions: "Why did this particular frame fail Reed-Solomon decode? Why did this packet get marked as invalid? Why am I missing a block of telemetry from my query?" -- which are completely valid questions to ask from a GDS Engineer's point of view, and large families of tools have been designed to help answer these questions. But these are not the questions that most users care about - which are more like: "Why is the battery state of charge trending down? Show me a summary image report for the last traverse to the target. Show me a data accountability summary for the last DSN pass." Answers to these questions, which are what users are looking for, requires a higher level of abstraction and supporting tools than mining through ones and zeros. JPL has created a next generation capability called the Mission Data Processing and Control System (MPCS) which is designed to support this higher level of abstraction by providing customizable views of the ground system combining collections of lower level information into more meaningful ways. Instead of examining frames, packets, and individual telemetry data points -- MPCS is capable of providing comprehensive summary reports, product status, overall flight/ground event status, as well as payload health summaries. Based on these higher level views, end users can make tactical or strategic decisions, or drop into detailed analysis as needed. System designers need to continue building systems that support low level GDS troubleshooting - but the basic design of a GDS should be geared towards what end users actually need to see. This paper will describe the capabilities of MPCS that directly support these higher levels of abstraction, and which are being used today in missions such as the Mars Science Laboratory and other NASA missions.

MPCS↗

NASA NTRS2021

An Evaluation of the CAN bus for Use on the Europa Lander Motor Controller

This paper will present the application of the Controller Area Network (CAN) for communication between the Motor Control Processor and the Europa Lander Motor Control Cards. The Europa Lander mission is concerned about lowering the mass, volume, and power so that it can maximize its science return. The motor controller uses multiple Motor Control Cards to control the 24 motors that will be operating in the extremes of the Europa environment. The CAN bus was considered because of its multi-drop nature, low power interface, and simple communication protocol. Beyond communication with the motor controller cards we also use the CAN bus interface to gather telemetry from the Power Conversion Card. Our system requires the collection of telemetry at a rate of 64Hz from the Power Conversion Card and all active motor controllers along with the sending of control packets and the receipt of control parameters at 512 Hz. In the paper we will address the ability of the CAN bus to meet these requirements along with our Arduino based test system used to learn about the CAN bus standard and verify our analysis.

Lias, Malcolm↗

NASA NTRS1993

Statistical and dynamical analysis of internal waves on the continental shelf of the Middle Atlantic Bight from Space Shuttle photographs

The internal waves on the continental shelf on the Middle Atlantic Bight seen on Space Shuttle photographs taken during the STS-40 mission in June 1991 are measured and analyzed. The internal wave field in the sample area has a three-level structure which consists of packet groups, packets, and solitons. An average packet group wavelength of 17.5 km and an average soliton wavelength of 0.6 km are measured. Finite-depth theory is used to derive the dynamic parameters of the internal solitons: the maximum amplitude of 5.6 m, the characteristic phase speed of 0.42 m/s, the characteristic period of 23.8 min, the velocity amplitude of the water particles in the upper and lower layers of 0.13 m/s and 0.030 m/s respectively, and the theoretical energy per unit crest line of 6.8 x 10 exp 4 J/m. The frequency distribution of solitons is triple-peaked rather than continuous. The major generation source is at 160 m water depth, and a second is at 1800 m depth, corresponding to the upper and lower edges of the shelf break.

Zheng, Quanan↗

NASA NTRS2006

Reconfigurable Protocol Sensing in an End-to-End Demonstration

In this work, we present sensing performance using an architecture for a reconfigurable protocol chip for spacebased applications. Toward utilizing the IP packet architecture, utilizing data link layer framing structures for multiplexed data on a channel are the targeted application considered for demonstration purposes. Specifically, we examine three common framing standards and present the sensing performance of these standards and their relative de-correlation metrics. Some analysis is performed to investigate the impact of lossy links. Finally, we present results on a demonstration platform that integrated reconfigurable sensing technology into the Ground Station Interface Device (GRID) for End-to-End IP demonstrations in space.

space based applications↗

NASA NTRS1994

Regular Topologies for Gigabit Wide-Area Networks

In general terms, this project aimed at the analysis and design of techniques for very high-speed networking. The formal objectives of the project were to: (1) Identify switch and network technologies for wide-area networks that interconnect a large number of users and can provide individual data paths at gigabit/s rates; (2) Quantitatively evaluate and compare existing and proposed architectures and protocols, identify their strength and growth potentials, and ascertain the compatibility of competing technologies; and (3) Propose new approaches to existing architectures and protocols, and identify opportunities for research to overcome deficiencies and enhance performance. The project was organized into two parts: 1. The design, analysis, and specification of techniques and protocols for very-high-speed network environments. In this part, SRI has focused on several key high-speed networking areas, including Forward Error Control (FEC) for high-speed networks in which data distortion is the result of packet loss, and the distribution of broadband, real-time traffic in multiple user sessions. 2. Congestion Avoidance Testbed Experiment (CATE). This part of the project was done within the framework of the DARTnet experimental T1 national network. The aim of the work was to advance the state of the art in benchmarking DARTnet's performance and traffic control by developing support tools for network experimentation, by designing benchmarks that allow various algorithms to be meaningfully compared, and by investigating new queueing techniques that better satisfy the needs of best-effort and reserved-resource traffic. This document is the final technical report describing the results obtained by SRI under this project. The report consists of three volumes: Volume 1 contains a technical description of the network techniques developed by SRI in the areas of FEC and multicast of real-time traffic. Volume 2 describes the work performed under CATE. Volume 3 contains the source code of all software developed under CATE.

Shacham, Nachum↗

NASA NTRS1985

Analysis of adaptive algorithms for an integrated communication network

Techniques were examined that trade communication bandwidth for decreased transmission delays. When the network is lightly used, these schemes attempt to use additional network resources to decrease communication delays. As the network utilization rises, the schemes degrade gracefully, still providing service but with minimal use of the network. Because the schemes use a combination of circuit and packet switching, they should respond to variations in the types and amounts of network traffic. Also, a combination of circuit and packet switching to support the widely varying traffic demands imposed on an integrated network was investigated. The packet switched component is best suited to bursty traffic where some delays in delivery are acceptable. The circuit switched component is reserved for traffic that must meet real time constraints. Selected packet routing algorithms that might be used in an integrated network were simulated. An integrated traffic places widely varying workload demands on a network. Adaptive algorithms were identified, ones that respond to both the transient and evolutionary changes that arise in integrated networks. A new algorithm was developed, hybrid weighted routing, that adapts to workload changes.

Reed, Daniel A.↗

NASA NTRS2018

ADS-B Mixed sUAS and NAS System Capacity Analysis and DAA Performance

Automatic Dependent Surveillance-Broadcast (ADS-B) technology was introduced more than twenty years ago to improve surveillance within the US National Airspace Space (NAS) as well as in many other countries. Via the NextGen initiative, implementation of ADS-B technology across the US is planned in stages between 2012 and 2025. ADS-B's automatic one second epoch packet transmission exploits on-board GPS-derived navigational information to provide position information, as well as other information including vehicle identification, ground speed, vertical rate and track angle. The purpose of this technology is to improve surveillance data accuracy and provide access to better situational awareness to enable operational benefits such as shorter routes, reduced flight time and fuel burn, and reduced traffic delays, and to allow air traffic controllers to manage aircraft with greater safety margins. Other than the limited amount of information bits per packet that can be sent, ADS-B's other hard-limit limitation is capacity. Small unmanned aircraft systems (sUAS) can utilize limited ADS-B transmission power, in general, thus allowing this technology to be considered for use within a combined NAS and sUAS environment, but the potential number and density of sUAS predicted for future deployment calls into question the ability of ADS-B systems to meet the resulting capacity requirement. Hence, studies to understand potential limitations of ADS-B to fulfill capacity requirements in various sUAS scenarios are of great interest. In this paper we, validate/improve on, previous work performed by the MITRE Corporation concerning sUAS power and capacity in a sUAS and General Aviation (GA) mixed environment. In addition, we implement its inherent media access control layer capacity limitations which was not shown in the MITRE paper. Finally, a simple detect and avoid (DAA) algorithm is implemented to display that ADS-B technology is a viable technology for a mixed NAS/sUAS environment even in proposed larger mixed density environments.

Matheou, Konstantin J.↗

NASA NTRS2018

ADS-B Mixed sUAS and NAS System Capacity Analysis and DAA Performance

Automatic Dependent Surveillance-Broadcast (ADS-B) technology was introduced more than twenty years ago to improve surveillance within the US National Airspace Space (NAS) as well as in many other countries. Via the NextGen initiative, implementation of ADS-B technology across the US is planned in stages between 2012 and 2025. ADS-B's automatic one second epoch packet transmission exploits on-board GPS-derived navigational information to provide position information, as well as other information including vehicle identification, ground speed, vertical rate and track angle. The purpose of this technology is to improve surveillance data accuracy and provide access to better situational awareness to enable operational benefits such as shorter routes, reduced flight time and fuel burn, and reduced traffic delays, and to allow air traffic controllers to manage aircraft with greater safety margins. Other than the limited amount of information bits per packet that can be sent, ADS-B's other hard-limit limitation is capacity. Small unmanned aircraft systems (sUAS) can utilize limited ADS-B transmission power, in general, thus allowing this technology to be considered for use within a combined NAS and sUAS environment, but the potential number and density of sUAS predicted for future deployment calls into question the ability of ADS-B systems to meet the resulting capacity requirement. Hence, studies to understand potential limitations of ADS-B to fulfill capacity requirements in various sUAS scenarios are of great interest. In this paper we, validate/improve on, previous work performed by the MITRE Corporation concerning sUAS power and capacity in a sUAS and General Aviation (GA) mixed environment. In addition, we implement its inherent media access control layer capacity limitations which was not shown in the MITRE paper. Finally, a simple detect and avoid (DAA) algorithm is implemented to display that ADS-B technology is a viable technology for a mixed NAS/sUAS environment even in proposed larger mixed density environments.

Matheou, Konstantin↗

NASA NTRS2005

Analysis of Quantum Information Test-Bed by Parametric Down-Converted Photons Interference Measurement

Quantum optical experiments require all the components involved to be extremely stable relative to each other. The stability can be "measured" by using an interferometric experiment. A pair of coherent photons produced by parametric down-conversion could be chosen to be orthogonally polarized initially. By rotating the polarization of one of the wave packets, they can be recombined at a beam splitter such that interference will occur. Theoretically, the interference will create four terms in the wave function. Two terms with both photons going to the same detector, and two terms will have the photons each going to different detectors. However, the latter will cancel each other out, thus no photons will arrive at the two detectors simultaneously under ideal conditions. The stability Of the test-bed can then be inferred by the dependence of coincidence count on the rotation angle.

To, Wing H.↗

DOE OSTI2021

Analysis of the EMCCD point-source response using x-rays

Electron Multiplying Charge Coupled Devices, EMCCD are used as x-ray detectors. The NSLS-II Soft Inelastic x-ray Scattering (SIX) beam line has two EMCCDs for x-ray detection in the spectrometer arm. The spectrometer with high resolving power disperses x-rays vertically. The x-ray vertical position on the sensor plane is related to its energy. This allows for very accurate x-ray energy measurements through x-ray coordinates. X-rays interact with silicon and create a number of electron-hole pairs proportional to the x-ray energy. Electrons drift and diffuse toward pixel gates and are collected there. The diffused electrons form a charge cloud distributed over several neighboring pixels. This charge sharing enables coordinate measurements with accuracy better than the pixel pitch. The charge distribution shape has to be taken into account to achieve ultimate accuracy in coordinate measurements. In this paper, we present a method of the charge distribution shape analysis and demonstrate its applications. The drift and diffusion of electrons ftom the point of generation to pixel gates results in the bell-shaped electron cloud usually approximated by Gaussian shape. The number of electrons collected under a pixel is proportional to the shape function integral. These electron packets get transferred to the sense node of the output amplifier. The transfer process could introduce distortions to the original charge distribution. For example, during transfers, electrons in the packet could be exposed to traps if they are present in the sensor. The trapping and later the release processes distort the apparent shape of the charge distribution. Therefore, deviations of the charge distribution shape ftom the originally symmetrical form can indicate the presence of trap centers in the sensor and can be used for sensor diagnostics.

47 OTHER INSTRUMENTATION↗

DOE OSTI2022

Simulation of the photodetachment spectra of the nitrate anion (NO 3 ₋ ) in the B ~ 2 E' energy range and non-adiabatic electronic population dynamics of NO 3

The photodetachment spectrum of the nitrate anion (NO 3 ₋ ) in the energy range of the NO 3 second excited state is simulated from first principles using quantum wave packet dynamics. The prediction at 10 K and 435 K relies on the use of an accurate full-dimensional fully coupled five state diabatic potential model utilizing an artificial neural network. The ability of this model to reproduce experimental spectra was demonstrated recently for the lower energy range. Analysis of the spectra indicates a weaker Jahn–Teller coupling compared to the first excited state. The detailed non-adiabatic dynamics is studied by computing the population dynamics. An ultra-fast non-statistical radiationless decay is found only among the Jahn–Teller components, which is followed by a slow statistical non-radiative decay among the different state manifolds. The latter is reproduced perfectly by a simple first order kinetics model. The dynamics in the second excited state is not affected by the presence of a conical intersection with the first excited state manifold.

36 MATERIALS SCIENCE↗