Search NASA⌕ Search

SEARCH · Search NASA

Results for “phase segregation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

The effect of oxygen flow rate and radio frequency plasma power on cubic ZnMgO ultraviolet sensors grown by plasma-enhanced molecular beam epitaxy

Cubic Zn{sub 1-x}Mg{sub x}O thin films were produced by Plasma-Enhanced Molecular Beam Epitaxy. Oxygen flow rate and applied Radio-Frequency (RF) plasma power were varied to investigate the impact on film growth and optoelectronic device performance. Solar-blind and visible-blind detectors were fabricated with metal-semiconductor-metal interdigitated Ni/Mg/Au contacts and responsivity is compared under different growth conditions. Increasing oxygen flow rate and RF plasma power increased Zn incorporation in the film, which leads to phase segregation at relatively high Zn/Mg ratio. Responsivity as high as 61 A/W was measured in phase-segregated ZnMgO visible-blind detectors.

36 MATERIALS SCIENCE↗

Impact of Cooling Rate and Thermal Mass on Supercooling in a Salt-Hydrogel Complex for Thermal Energy Storage

Glauber’s salt is a promising phase change material for building thermal management because of its high latent heat, acceptable melting temperature of 32.3 °C for indoor air1,2. Despite these advantages, the practical application of Glauber’s salt in thermal energy storage systems is still challenging due to supercooling and phase segregation1–3. Here, we report the impact of temperature ramp rate and thermal mass on the supercooling of Glauber’s salt through the DSC and T-history experiment. The ramp rate effect was studied with a wide range of ramp rates in 1 to 10 °C/min in DSC and 1 to 4 °C/min in the T-history experiment. The thermal mass effect was investigated by comparing DSC and T-history experiment. The latent heat was also analyzed for different ramp rates and thermal mass conditions. The melting temperatures of Glauber’s salt from the two techniques were identical while freezing temperatures were different because of the thermal mass effect. During freezing in the T-history experiment, the latent heat was reduced by around 75% to the latent heat in melting due to supercooling and phase segregation. To overcome this bottleneck, we developed a novel hydrogel complex that reduces the supercooling and prevents phase segregation to maintain volumetric energy density for 100 cycles. Thermodynamic analysis accounting for composition shows that a higher salt composition can further enhance the volumetric energy storage density. For example, a 10% increase in the weight percentage of salt leads to about 50% enhancement in volumetric energy storage density. References: 1. D. R. Biswas, Solar Energy. 19, 99–100 (1977). 2. S. M. Hasnain, Energy Conversion and Management. 39, 1127–1138 (1998). 3. Byung Chul Shin, Sang Done Kim, P. Won-Hoon, Energy. 14, 921–930 (1989).

inorganic, thermodynamics↗

Microstructure-dependent rate theory model of defect segregation and phase stability in irradiated polycrystalline LiAlO 2

We report gamma lithium aluminate (LiAlO 2 ) is a breeder material for tritium and is one of key components in a tritium-producing burnable absorber rod (TPBAR). Dissolution and precipitation of second phases such as LiAl 5 O 8 and voids are observed in irradiated LiAlO 2 . Such microstructure changes cause the degradation of thermomechanical properties of LiAlO 2 and affect tritium retention and release kinetics, and hence, the TPBAR performance. In this work, a microstructure-dependent model of radiation-induced segregation (RIS) has been developed for investigating the accumulation of species and phase stability in polycrystalline LiAlO 2 structures under irradiation. Three sublattices (i.e. [Li, Al, V] I [O, V o ] II [Li i , Al i , O i , V i ] III ), and concentrations of six diffusive species (i.e. Li; vacancy of Li or Al at [Li, Al, V] I sublattice, O vacancy at [O, V o ] II sublattice, and Li, Al and O interstitials at [Li i , Al i , O i , V i ] III interstitial sublattices; are used to describe spatial and temporal distributions of defects and chemistry. Microstructure-dependent thermodynamic and kinetic properties including the generation, reaction, and chemical potentials of defects and defect mobility are taken into account in the model. The parametric studies demonstrated the capability of the developed RIS model to assess the effect of thermodynamic and kinetic properties of defects on the segregation and depletion of species in polycrystalline structures and to explain the phase stability observed in irradiated LiAlO 2 samples. The developed RIS model will be extended to study the precipitation of LiAl 5 O 8 and voids and tritium retention by integrating the phase-field method.

36 MATERIALS SCIENCE↗

Activation Energy for End-of-Life Solder Bond Degradation: Thermal Cycling of Field-Aged PV Modules

The longevity of solar photovoltaic modules depends on the durability and reliability of their components, one of which is the solder bonds in interconnect ribbons. The solder joints experience stresses from thermal cycling and constant elevated temperatures (40 °C-70 °C) in regular field operation leading to thermo-mechanical fatigue and intermetallic compound formation. To study the end-of-life wear-out mechanisms and to obtain activation energy of solder bond degradation, here two field-aged modules from Arizona-a 21-year-old Solarex MSX60 module (with Sn62Pb36Ag2 at the solder joints) and an 18-year-old Siemens M55 module (with Sn60Pb40 at the solder joints)-underwent 800 and 400 modified thermal cycles, respectively. Using three heating blankets, each module had three temperature zones maintained at 85, 95, and 105 °C during the 15-min hot dwell time of the thermal cycle. Cell-level series resistance data obtained from three temperature zones enabled the calculation of activation energy for solder bond degradation for the MSX60 and the M55 modules to be 0.12 eV and 0.35 eV, respectively. From each temperature zone in both modules, busbar-solder samples were obtained, imaged through SEM, and analyzed with energy-dispersive X-ray spectroscopy. In the MSX60 module with traces of Ag in the solder material, phase segregation and growth were primarily observed at high temperatures. For M55 modules without Ag in the solder material, major phase segregation was observed in all temperature zones. The IMC thickness for both modules increased with increasing module temperature. The beneficial effect of Ag in solder material on mitigating solder bond degradation is presented.

14 SOLAR ENERGY↗

The Effect Stacking Fault Segregation and Phase Transformations have on Creep Strength in Ni-based Superalloys

In this study, two commercially similar polycrystalline Ni-based disk superalloys (LSHR and ME3) were creep tested at 760C and 552MPa to approximately 0.3% plastic strain. LSHR consistently displayed superior creep properties at this stress/temperature regime even though the microstructural characteristics between the two alloys were comparable. High resolution structural and chemical analysis, however, revealed significant differences between the two alloys among active gamma prime shearing modes involving superlattice intrinsic and extrinsic stacking faults. In ME3, Co and Cr segregation and Ni and Al depletion were observed along the intrinsic faults - revealing a gamma prime -to- gamma phase transformation. Conversely in LSHR, an alloy with a higher W content, Co and W segregation was observed along the intrinsic faults. This observation combined with scanning transmission electron microscopy (STEM) simulations confirm a gamma prime-to-D019 phase transformation along the intrinsic faults in LSHR. Using experimental observations and density functional theory calculations, a novel local phase transformation strengthening mechanism is proposed that could be further utilized to improve the high temperature creep capabilities of Ni-base disk alloys.

Superalloy↗

Structural characterization of highly alloyed (Al,Gd)N thin films

Highly alloyed (Al,Gd)N is of potential interest in a variety of applications, including neutron detection and in devices such as non-volatile memory. Gd has been shown to have very low equilibrium solubility in AlN at room temperature; however, non-equilibrium deposition techniques such as sputtering are able to deposit thin films, which incorporate large amounts of Gd. Here, we characterize a highly-alloyed (Al,Gd)N combinatorial thin film grown by RF sputtering on a GaN substrate, looking for any evidence of chemical or phase segregation or structural disorder in the films. Compositions with between 13% and 32% Gd (on a cation basis) were studied. No evidence was found for chemical or phase segregation in any studied composition. Higher degrees of Gd incorporation led to greater structural disorder in the film and a tendency toward amorphization; however, electron diffraction shows that the film does not become fully amorphous at any of the studied compositions, instead retaining textured local order even at 32% Gd. Electron energy loss spectra suggest that the material retains a locally wurtzite-like tetrahedral bonding environment at all studied compositions.

36 MATERIALS SCIENCE↗

First-principles thermodynamics study of phase stability in inorganic halide perovskite solid solutions

Halide substitution gives rise to a tunable band gap as a function of composition in halide perovskite materials. However, photoinduced phase segregation, observed at room temperature in mixed halide APb(I x Br 1–x ) 3 systems, limits open circuit voltages and decreases photovoltaic device efficiencies. We investigate equilibrium phase stability of orthorhombic P nma γ-phase CsM(X x Y 1–x ) 3 perovskites where M is Pb or Sn, and X and Y are Br, Cl, or I. Finite-temperature phase diagrams are constructed using a cluster expansion effective Hamiltonian parameterized from first-principles density-functional-theory calculations. Solid solution phases for CsM(I x Br 1–x ) 3 andCsM(Br x Cl 1–x ) 3 are predicted to be stable well below room temperature while CsM(I x Cl 1–x ) 3 systems have miscibility gaps that extend above 400 K. The height of the miscibility gap correlates with the difference in volume between end members. Also layered ground states are found on the convex hull at x = 2/3 for CsSnBr 2 Cl, CsPbI 2 Br, and CsPbBrCl 2 . The impact of these ground states on the finite temperature phase diagram is discussed in the context of the experimentally observed photoinduced phase segregation.

36 MATERIALS SCIENCE↗

Effect of Gradient Sequencing on Copolymer Order-Disorder Transitions: Phase Behavior of Styrene/n-Butyl Acrylate Block and Gradient Copolymers

We investigate the effect of gradient sequence distribution in copolymers on order-disorder transitions, using rheometry and small-angle X-ray scattering to compare the phase behavior of styrene/n-butyl acrylate (S/nBA) block and gradient copolymers. Relative to block sequencing, gradient sequencing increases the molecular weight necessary to induce phase segregation by over 3-fold, directly consistent with previous predictions from theory. Results also suggest the existence of both upper and lower order-disorder transitions in a higher molecular weight S/nBA gradient copolymer, made accessible by the shift in order-disorder temperatures from gradient sequencing. The combination of transitions is speculated to be inaccessible in S/nBA block copolymer systems due to their overlap at even modest molecular weights and also their location on the phase diagram relative to the polystyrene glass transition temperature. Finally, we discuss the potential impacts of polydispersity and chain-to-chain monomer sequence variation on gradient copolymer phase segregation.

36 MATERIALS SCIENCE↗

Photoacid-Modified Nafion Membrane Morphology Determined by Resonant X-ray Scattering and Spectroscopy

Covalent attachment of photoacid dye molecules to perfluorinated sulfonic acid membranes is a promising route to enable active light-driven ion pumps, but the complex relationship between chemical modification and morphology is not well understood in this class of functional materials. In this study we demonstrate the effect of bound photoacid dyes on phase-segregated membrane morphology. Resonant X-ray scattering near the sulfur K-edge reveals that introduction of photoacid dyes to the end of the ionomer side chains enhances phase segregation among ionomer domains, and the ionomer domain spacing increases with increasing amount of bound dye. Furthermore, relative crystallinity is marginally enhanced within semicrystalline domains composed of the perfluorinated backbone. Finally, X-ray absorption spectroscopy coupled with first-principles density functional theory calculations suggest that above a critical concentration, the multiple hydrophilic groups on the attached photoacid dye may help increase residual water content and promote hydration of adjacent sulfonic acid side chains under dry or ambient conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Rapid Development of Hybrid Perovskites and Novel Tandem Architectures

Multijunction solar cells based on epitaxially grown III-V materials hold the record for solar energy power conversion efficiency (PCE). However, due to the high cost of fabricating these devices, they are typically only used for concentrator cells and space applications. The overarching goal of this project was to develop low-cost printable hybrid perovskite (HP) materials appropriate and optimized for tandem solar cells with high power conversion efficiency under “1 Sun” illumination. Key results and findings over the course of the project we: Developed higher-performance high-bandgap (1.75 eV) perovskite materials and devices. In particular, we explored tens-of-thousands of compositions for high bandgap perovskites, achieving quasi-Fermi level splitting of 1.35 eV for a 1.75 eV bandgap material. We achieved World-record open circuit voltages from single junction p-i-n devices, 1.24 V from 1.75 eV bandgap material, which is what is preferable for tandems with a PCE of 14.3% using a guanidinium/formanadinium/ cesium alloyed lead iodobromide. We also developed a series of World-record efficiency devices at higher band-gaps based on 2D/3D perovskites using PEA. Developed higher-performance low-bandgap (1.35 eV) perovskite materials and devices. In particular, we developed a 1.35 eV bandgap perovskite of composition MAPb0.5Sn0.5(I0.8Br0.2)3 and showed its superiority to MAPb0.75Sn0.25I3. High efficiency solar cells were fabricated using PEDOT:PSS and doped-ICBA as HTL and ETL, respectively. Short circuit currents of 25.7 mA/cm2 and PCEs of 17.1% were obtained. Developed mechanically stacked 4-terminal CIGS-Perovskite tandems with PCE of 18.8% and monolithic 2-terminal CIGS-Perovskite tandems with PCE of 8.5%. The low efficiency of the monolithic device is a result of the high surface roughness of the solution processed CIGS bottom cells. This is not an intrinsic problem for CIGS-perovskite tandems, but does mean that smooth evaporated or sputtered CIGS films likely need to be used, unless a polishing step is employed. Developed monolithic 2-terminal Perovskite-Perovskite tandems with a stabilized PCE of 18.5%. This was the World-record perovskite-perovskite monolithic tandems for over a year in 2017-2018. Revealed that light is not an essential component of the so-called “light-induced” phase segregation. By using charge injection in the dark and electroluminescence, we showed that the presence of electrons in the conduction band and hole in the valence band is sufficient to drive the nearly ubiquitously observed phase segregation in high bandgap perovskites. Developed a new method to simultaneously measure absolute intensity photoluminescence and photoconductivity and use them to obtain simultaneous in-situ measurement of quasi-Fermi level splitting and diffusion length. This is important since it provides a proxy for device Voc and device Jsc. In addition, 67 papers were published with support from this award that detail many more advances in the field, including numerous publications in high impact journals such as Nature Photonics, Advanced Materials, ACS Energy Letters, and Energy and Environmental Science.

14 SOLAR ENERGY↗

Stabilization and transformation of Pt nanocrystals supported on ZnAl 2 O 4 spinel

The role of interfacial interaction on the stabilization and transformation of Pt nanocrystals supported on zinc aluminate (ZnAl2O4) was systematically studied in this work. In addition to the remarkable stability of Pt nanocrystals supported on the {111} ZnAl2O4 facet under harsh oxidizing atmosphere, we also identified the phase segregation of ZnAl2O4 to ZnO and Al2O3 and the transformation of Pt to PtZn bimetallic alloy for Pt supported on other facets. High resolution scanning transmission electron microscope and X-ray diffraction analysis reveal the phase segregation is associated with a cation migration mechanism associated with replacement of Zn2+ by Al3+ in the spinel structure. This work confirms the strong interfacial interactions between precious metal nanocrystals and the spinel support is a general mechanism for stabilizing precious metal catalysts, and has important implication for the rational design of stable integrated catalysis systems

Environmental Molecular Sciences Laboratory↗

Radiation-Induced Segregation and Phase Stability in Candidate Alloys for the Advanced Burner Reactor

Major accomplishments of this project were the following: 1) Radiation induced depletion of Cr occurs in alloy D9, in agreement with that observed in austenitic alloys. 2) In F-M alloys, Cr enriches at PAG grain boundaries at low dose (<7 dpa) and at intermediate temperature (400°C) and the magnitude of the enrichment decreases with temperature. 3) Cr enrichment decreases with dose, remaining enriched in alloy T91 up to 10 dpa, but changing to depletion above 3 dpa in HT9 and HCM12A. 4) Cr has a higher diffusivity than Fe by a vacancy mechanism and the corresponding atomic flux of Cr is larger than Fe in the opposite direction to the vacancy flux. 5) Cr concentration at grain boundaries decreases as a result of vacancy transport during electron or proton irradiation, consistent with Inverse Kirkendall models. 6) Inclusion of other point defect sinks into the KLMC simulation of vacancy-mediated diffusion only influences the results in the low temperature, recombination dominated regime, but does not change the conclusion that Cr depletes as a result of vacancy transport to the sink. 7) Cr segregation behavior is independent of Frenkel pair versus cascade production, as simulated for electron versus proton irradiation conditions, for the temperatures investigated. 8) The amount of Cr depletion at a simulated planar boundary with vacancy-mediated diffusion reaches an apparent saturation value by about 1 dpa, with the precise saturation concentration dependent on the ratio of Cr to Fe diffusivity. 9) Cr diffuses faster than Fe by an interstitial transport mechanism, and the corresponding atomic flux of Cr is much larger than Fe in the same direction as the interstitial flux. 10) Observed experimental and computational results show that the radiation induced segregation behavior of Cr is consistent with an Inverse Kirkendall mechanism.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Segregation and Phase Transformations Along Superlattice Intrinsic Stacking Faults in Ni-Based Superalloys

In this study, local chemical and structural changes along superlattice intrinsic stacking faults combine to represent an atomic-scale phase transformation. In order to elicit stacking fault shear, creep tests of two different single crystal Ni-base superalloys, ME501 and CMSX-4, were performed near 750 degrees Centigrade using stresses of 552 megapascals and 750 megapascals, respectively. Through high resolution Scanning Transmission Electron Microscopy (STEM) and state-of-the-art energy dispersive x-ray spectroscopy, ordered compositional changes were measured along SISFs (Superlattice Intrinsic Stacking Faults) in both alloys. For both instances, the elemental segregation and local crystal structure present along the SISFs are consistent with a nanoscale to D019 (ordering of a hexagonal close-packed crystal) phase transformation. Another notable observation is prominent Cr- and Co-rich Cottrell atmospheres and new evidence of more complex reordering processes responsible for the formation of these faults. These findings are further supported using density functional theory calculations and High Angle Annular Dark Field (HAADF) STEM image simulations.

STEM-EDS↗

Electrochemical Li intercalation in b-As y P 1–y alloys: In-situ Raman spectroscopy study

Structural evolution of b-As y P 1-y alloys with varying As concentration, y was studied during Li-intercalation using in-situ Raman spectroscopy. A monotonic redshift of all the vibrational modes corresponding to P-P bonds (A 1 g , A 2 g , B 2g ), As-As bonds (A 1 g , A 2 g , B 2g ), and As-P bonds of all the samples was observed during the initial stages of the intercalation process due to the softening of each mode caused by the intercalation driven donor-type charge-transfer from Li to b-As y P 1-y . The emergence of a new peak identified as the E g mode of gray As, above an intercalation threshold, is indicative of the presence of an intercalation-driven structural phase segregation process. Further, the A 1g mode of gray As emerging after this intercalation threshold lies in close proximity of the A 2 g Raman mode of b-As y P 1-y . All the peaks beyond the intercalation threshold show an upshift due to the co-existence of gray As with b-As y P 1-y alloys causing strain and thus hardening of the phonon modes. In the sample with the highest As concentration phase segregation takes place during the synthesis process. Computational modeling reveals the co-existence of gray As in the b-As y P 1-y alloys with high As concentrations. It also confirms the existence of a local structural segregation taking place at a critical Li concentration during the intercalation process. Furthermore, this work shows the significance of intercalation on structural changes in the search for new phases of b-As y P 1-y alloys.

2D Materials↗

Mode-of-Action of Self-Extinguishing Polymer Blends Containing Organoclays

We have shown that the addition of nanoclays is an effective means for enhancing the flame retardant properties of polymer blends. Polymer blends are difficult to render flame retardant even with the addition of flame retardant agents due to dispersion and phase segregation during the heating process. We show that the addition of 5% functionalized Cloisite 20A clays in combination with 15% decabromodiphenyl ether and 4% antimony trioxide to a polystyrene/poly(methyl methacrylate) blend can render the compound flame resistant within the UL-94-V0 standard. Using a variety of micro-characterization methods, we show that the clays are concentrated at the interfaces between the polymers in this blend and completely suppress phase segregation. The flame retardant (FR) is absorbed onto the clay surfaces, and the exfoliation of the clays also distributes the FR agent uniformly within the matrix. TGA of the nanocomposite indicates that prior to the addition of clay, the dissociation times of the individual components varied by more than 20 C, which complicated the gas-phase kinetics. Addition of the clays causes all the components to have a single dissociation temperature, which enhanced the efficacy of the FR formula in the gas phase. Cone calorimetry also indicated that the clays decreased the heat release rate (HRR) and the mass loss rate (MLR), due to the formation of a robust char. In contrast, minimal charring occurred in blends containing just the FR. SEM examination of the chars showed that the clay platelets were curved and in some cases tightly folded into nanotube-like structures. These features were only apparent in blends, indicating that they might be associated with thermal gradients across the polymer phase interface. SEM and SAXS examinations of the nanocomposites after partial exposure to the flame indicated that the clays aggregated into ribbon-like structures, approximately microns in length, after the surfactant thermally decomposed. Thermal modeling indicated that these ribbons might partially explain the synergy due to better distribution of the heat and improve the mechanical properties of the melt at high temperatures, in a manner similar to the one reported for carbon nanotubes.

36 MATERIALS SCIENCE↗

Microstructural Evaluation of Phase Instability in Large Bandgap Metal Halide Perovskites

The optoelectronic performance of organic–inorganic halide perovskite (OIHP)-based devices has been improved in recent years. Particularly, solar cells fabricated using mixed-cations and mixed-halides have outperformed their single-cation and single-halide counterparts. Yet, a systematic evaluation of the microstructural behavior of mixed perovskites is missing despite their known composition-dependent photoinstability. Here, we explore microstructural inhomogeneity in (FAPbI 3 ) x (MAPbBr 3 ) 1– x using advanced scanning probe microscopy techniques. In this work, contact potential difference (CPD) maps measured by Kelvin probe force microscopy show an increased fraction of grains exhibiting a low CPD with flat topography as MAPbBr 3 concentration is increased. The higher portion of low CPD contributes to asymmetric CPD distribution curves. Chemical analysis reveals these grains being rich in MA, Pb, and I. The composition-dependent phase segregation upon illumination, reflected on the emergence of a low-energy peak emission in the original photoluminescence spectra, arises from the formation of such grains with flat topology. Bias-dependent piezo-response force microscopy measurements, in these grains, further confirm vigorous ion migration and cause a hysteretic piezo-response. Our results, therefore, provide insights into the microstructural evaluation of phase segregation and ion migration in OIHPs pointing toward process optimization as a mean to further enhance their optoelectronic performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Enhanced Photostability of “Hollow” Mixed Halide Wide-Bandgap Perovskite Films

We investigated the role of hollow perovskite architectures in enhancing the photostability of mixed halide wide-bandgap perovskites. We focused on mitigating photoluminescence (PL) peak shifts caused by phase segregation when exposed to light. By analyzing the optical and structural properties of mixed bromide/iodide hollow perovskite thin films, we observed that the incorporation of hollow structures reduced the ionic conductivity in the films, leading to improved photostability compared to non-hollow perovskite samples. The mixed halide hollow perovskite thin films exhibited increased the bandgap. High-power laser irradiation was used to induce phase segregation, and changes in the PL emission spectra were measured as a function of irradiation time. The mixed halide hollow perovskite thin films exhibited reduced PL peak shifts compared to the control samples. The inclusion of enI 2 (en = ethylenediamine) resulted in a reduction in the overall ionic conductivity of the films and a lower trap density. Hollow perovskite films incorporated in solar cells indicated that while the initial efficiency of the solar cells decreased with increasing enI 2 concentration, the open-circuit voltage value increased, potentially due to the slight enhancement of the band gap. Furthermore, the findings highlight the potential of hollow perovskite architectures in enhancing the photostability of mixed halide perovskites

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗