Search NASA⌕ Search

SEARCH · Search NASA

Results for “plastic oxidation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Mechanical Performance and Mesostructure Analysis of Proton-Irradiated Fused Filament Fabrication Acrylonitrile Butadiene Styrene Material

The use of fused filament fabrication (FFF) acrylonitrile butadiene styrene (ABS) and other thermoplastics in radiation environments is beginning to be studied as possible replacements for traditionally manufactured parts and tools. Interlayer adhesion within the mesostructure has been shown in published literature to be an integral component in the strength of FFF ABS. Research of irradiated 3D printed polymers has primarily focused on the influence of gamma irradiation on the mechanical properties of FFF ABS samples, without evaluating its impact on the mesostructure of the samples. The purpose of this paper is to understand the mechanical damage caused by proton radiation on FFF ABS samples through the evaluation of the mesostructure of the ABS samples. To achieve this objective, proton radiation at 40 MeV was applied to FFF ABS samples at radiation doses up to 1.0 MGy at a dose rate of 1 MGy/hr. Following the irradiation, tensile testing was performed on the samples. Here, the fractured surfaces of the tested samples were subsequently observed using a scanning electron microscope. The mechanical test results show an increase in the ultimate tensile strength (UTS) and a decrease in the ductility of the irradiated samples. Statistical analysis on the results shows that there is a statistically significant difference in the UTS and the ductility of unirradiated and 1.0 MGy irradiated samples and between irradiated samples and 1.0 MGy samples. In addition, the percentage elongation at break has statistically significant differences in the means between irradiated samples and 1.0 MGy samples. The UTS has statistically significant differences in the means between 0.1 MGy and 1.0 MGy. The difference in the means between the unirradiated and the 1.0 MGy samples is the most significant for both the UTS and elongation at break. The scanning electron microscopy (SEM) results indicated that interlayer adhesion improved as a function of radiation dose corresponding to the increase in tensile strength. The SEM results also showed that crazing and plastic deformation were reduced; aligning with the loss in ductility observed in the tensile tests results. The proton radiation is causing these mechanical and physical changes through two mechanisms: (1) dose rate effects on ionizing radiation-induced oxidative degradation; and (2) radiation heating effects of high energy (>1 MeV) charged particles.

electron microscopy↗
DOE OSTI2020

FAST-1.0 Software Release Document

The purpose of this document is to detail the release of FAST-1.0 and the documents that accompany the development and testing of FAST-1.0. Design requirements were for FAST-1.0 developed in the NRC Statement of Work (SOW) for NRC Agreement Number NRC-HQ-25-14-D-001 and are transcribed to this document as part of the Software Quality Assurance Plan for the FAST Code System, PNNL-28767. FAST 1.0 represents the merger of the FRAPCON and FRAPTRAN codes and as such FAST-1.0 performs steady state and transient fuel performance calculations described below. FAST-1.0 calculates the steady state response of light-water reactor fuel rods during long-term burnup. The code calculates temperature, pressure, and deformation of a fuel rod as functions of time-dependent fuel rod power and coolant boundary conditions. The phenomena modeled by the code include: 1) heat conduction through fuel and cladding to the coolant; 2) cladding elastic and plastic deformation; 3) fuel-cladding mechanical interaction; 4) fission gas release from the fuel and rod internal pressure; and 5) cladding oxidation. FAST is used to perform independent calculations for regulatory evaluations of fuel performance under normal operation and anticipated operational occurrences (AOOs).

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2022

FAST-1.1: A Computer Code for Thermal-Mechanical Nuclear Fuel Analysis under Steady-state and Transients (Developed under NQA-1-2017)

Fuel Analysis under Steady-state and Transients (FAST) is the U.S. Nuclear Regulatory Commission (NRC)’s computer code that calculates the steady-state and transient response of nuclear reactor fuel rods during long-term in-reactor burnup, anticipated operational occurrences (AOOs), design basis accidents (DBAs), and dry storage conditions. The code calculates the temperature, pressure, and deformation of a fuel rod as functions of time-dependent fuel rod power and coolant boundary conditions. The phenomena modeled by the code include: * heat conduction through the fuel and other materials * heat transfer from the cladding-to-coolant * cladding elastic and plastic deformation, including creep * fuel-cladding mechanical interaction * fission gas release from the fuel * rod internal pressure and void volume * cladding oxidation The code contains necessary material and coolant properties, as well as clad-to-coolant heat transfer correlations, for normal operation through postulated accidents and AOOs for today’s U.S.-based light water reactor (LWR) fuel designs. FAST-1.1 also contains preliminary materials and models for new LWR fuel concepts, such as accident tolerant fuel (ATF), and non-LWR fuel concepts such as metallic fuels for sodium fast reactors (SFRs). FAST has been developed for use on Windows and Linux operating systems. This document describes FAST-1.1 and is one of a series of documents on the code; the other documents detail the material properties used by FAST as well as its integral assessment to experiments and commercial data.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

FAST-1.2: A Computer Code for Thermal-Mechanical Nuclear Fuel Analysis under Steady-state and Transients

Fuel Analysis under Steady-state and Transients (FAST) is the U.S. Nuclear Regulatory Commission (NRC)’s computer code that calculates the steady-state and transient response of nuclear reactor fuel rods during long-term in-reactor burnup, anticipated operational occurrences (AOOs), design basis accidents (DBAs), and dry storage conditions. The code calculates the temperature, pressure, and deformation of a fuel rod as functions of time-dependent fuel rod power and coolant boundary conditions. The phenomena modeled by the code include: • heat conduction through the fuel and other materials • heat transfer from the cladding-to-coolant • cladding elastic and plastic deformation, including creep • fuel-cladding mechanical interaction • fission gas release from the fuel • rod internal pressure and void volume • cladding oxidation The code contains necessary material and coolant properties, as well as clad-to-coolant heat-transfer correlations, for normal operation through postulated accidents and AOOs for today’s U.S.-based light water reactor (LWR) fuel designs. FAST-1.2 also contains preliminary materials and models for new LWR fuel concepts, such as accident tolerant fuel (ATF), and non-LWR fuel concepts such as metallic fuels for sodium fast reactors (SFRs). FAST has been developed for use on Windows and Linux operating systems. This document describes FAST-1.2 and is one of a series of documents on the code; the other documents detail the material properties used by FAST as well as its integral assessment to experiments and commercial data.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

FAST-1.2.2: A Computer Code for Thermal-Mechanical Nuclear Fuel Analysis under Steady-state and Transients

Fuel Analysis under Steady-state and Transients (FAST) is the U.S. Nuclear Regulatory Commission (NRC)’s computer code that calculates the steady-state and transient response of nuclear reactor fuel rods during long-term in-reactor burnup, anticipated operational occurrences (AOOs), design basis accidents (DBAs), and dry storage conditions. The code calculates the temperature, pressure, and deformation of a fuel rod as functions of time-dependent fuel rod power and coolant boundary conditions. The phenomena modeled by the code include heat conduction through the fuel and other materials, heat transfer from the cladding-to-coolant, cladding elastic and plastic deformation (including creep), fuel-cladding mechanical interaction, fission gas release from the fuel, rod internal pressure, void volume, and cladding oxidation. The code contains necessary material and coolant properties, as well as clad-to-coolant heat transfer correlations, for normal operation through postulated accidents and AOOs for today’s U.S.-based light water reactor (LWR) fuel designs. FAST-1.2.2 also contains preliminary materials and models for new LWR fuel concepts, such as accident tolerant fuel (ATF), and non-LWR fuel concepts such as metallic fuels for sodium fast reactors (SFRs). FAST has been developed for use on Windows and Linux operating systems. This document describes FAST-1.2.2 and is one of a series of documents on the code; the other documents detail the material properties used by FAST as well as its integral assessment to experiments and commercial data.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Neuromorphic learning with Mott insulator NiO

Habituation and sensitization (nonassociative learning) are among the most fundamental forms of learning and memory behavior present in organisms that enable adaptation and learning in dynamic environments. Emulating such features of intelligence found in nature in the solid state can serve as inspiration for algorithmic simulations in artificial neural networks and potential use in neuromorphic computing. In this work, we demonstrate nonassociative learning with a prototypical Mott insulator, nickel oxide (NiO), under a variety of external stimuli at and above room temperature. Similar to biological species such as Aplysia, habituation and sensitization of NiO possess time-dependent plasticity relying on both strength and time interval between stimuli. A combination of experimental approaches and first-principles calculations reveals that such learning behavior of NiO results from dynamic modulation of its defect and electronic structure. An artificial neural network model inspired by such nonassociative learning is simulated to show advantages for an unsupervised clustering task in accuracy and reducing catastrophic interference, which could help mitigate the stability–plasticity dilemma. Mott insulators can therefore serve as building blocks to examine learning behavior noted in biology and inspire new learning algorithms for artificial intelligence.

42 ENGINEERING↗
DOE OSTI2020

Well-designed Crosslinked Polymer Electrolyte Enables High Ionic Conductivity and Enhanced Salt Solvation

A new facile single-step method to fabricate crosslinked polymer electrolyte membranes consisting of branched poly(ethyleneimine), (PEI) and poly(ethylene oxide), (PEO) is demonstrated. The membranes exhibit excellent ionic conductivity (1.2 × 10 –3 S cm –1 at 80 °C) with minimal addition of plasticizer (20 wt%). The amine functional group in the PEI-PEO crosslinked matrix provides Lewis basic and hydrogen bonding characteristics that facilitate the dissolution of lithium salt and enables a higher cation transport number than a PEO crosslinked matrix. The glass transition temperature, degree of crystallinity, and room temperature storage modulus increases with decreasing crosslink density and increasing ratio of free amines. The resultant ionic conductivity and mechanical strength can be flexibly tailored by varying the molar ratio of free amine moieties in the crosslinked PEI-PEO matrix. This study provides an improved synthesis method, in-depth characterization, and fundamental insights on the effect of free amine moieties on the transport properties of a highly conductive gel polymer electrolyte.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

FAST-1.0: A Computer Code for Thermal-Mechanical Nuclear Fuel Analysis under Steady-state and Transients: Developed under NQA-1-2017

Fuel Analysis under Steady-state and Transients (FAST) is the US Nuclear Regulatory Commission (NRC)’s computer code that calculates the steady-state and transient response of nuclear reactor fuel rods during long-term in-reactor burnup, anticipated operational occurrences (AOOs), design basis accidents (DBAs), and dry storage conditions. The code calculates the temperature, pressure, and deformation of a fuel rod as functions of time-dependent fuel rod power and coolant boundary conditions. The phenomena modeled by the code include: heat conduction through the fuel and other materials, heat transfer from the cladding-to-coolant, cladding elastic and plastic deformation, including creep, fuel-cladding mechanical interaction, fission gas release from the fuel, rod internal pressure and void volume, and cladding oxidation. The code contains necessary material and coolant properties, as well as clad-to-coolant heattransfer correlations, for normal operation through postulated accidents for today’s US-based light water reactor (LWR) fuel designs. FAST-1.0 also contains preliminary materials and models for new LWR fuel concepts, such as accident tolerant fuel (ATF), and non-LWR fuel concepts such as metallic fuels for sodium fast reactors (SFRs). FAST has been developed for use on Windows and Linux operating systems. This document describes FAST-1.0, which is the first official version of this code. This document is one of a series of documents on FAST; the other documents detail the material properties used by FAST as well as its integral assessment to experiments and commercial data.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Increasing pyrolysis oil yields and decreasing energy consumption via thermal oxo-degradation of polyolefins

Commercialization of pyrolysis of plastics in an inert atmosphere is challenging due to large thermal requirements. This study employs thermal oxo-degradation and demonstrates how oxygen supplied at modest equivalence ratios can both accelerate depolymerization and provide the enthalpy for pyrolysis without dramatically impacting desired product yields. The enthalpies for pyrolysis of high-density polyethylene (HDPE) and polypropylene (PP) are measured to be 2,300 ± 90 J g – -1 and 2,800 ± 60 J g –1 , respectively. Using air as an oxygen source in a fluidized bed reactor, HDPE and PP are rapidly deconstructed while using up to 84% less energy through the energy released by partial oxidation. Characterization of the thermal oxo-degradation product oil shows comparable composition to conventional pyrolysis oil. Thermal oxo-degradation proves to be a promising technology for upcycling of plastics by improving thermal depolymerization of waste plastics and reducing energy requirements while maintaining desirable yields.

42 ENGINEERING↗
DOE OSTI2024

Microwave-assisted catalytic gasification of mixed plastics and corn stover for low tar, hydrogen-rich syngas production

The challenge for efficient management of post-consumer plastic and biomass waste has grown over the past few decades due to their dramatic increases. In comparison to conventional gasification, microwave-assisted co-gasification of plastics and corn stover offers many benefits, including increased H 2 yield and gas components compared to unfavorable char/tar. Nonetheless, for future commercialization of the process and ease of product separation, further reduction of the undesirable tar is necessary, which can be achieved over the catalytic route. Here, in this work, we studied the catalytic effect of magnetite for microwave-assisted co-gasification of corn stover and plastic to make syngas with higher H 2 and lower tar selectivity over non-catalytic conditions. A 1:1:1 ratio of plastic-corn stover-magnetite was used to evaluate the reaction parameters such as temperature, space velocity, heating media, and catalytic cycles under gasification conditions. In comparison with the microwave non-catalytic route, a 100% increase in the total H 2 yield with 76% higher H 2 production efficiency (mmol/kWh) was achieved in the presence of the magnetite catalyst, while reducing the overall tar formation from 9% to 2%. When magnetite was reduced in situ during the reaction, it coupled with microwave and delivered oxygen radicals that cracked down plastic and corn stover intermediates generated from the synergistic effect under microwave heating. Soon after the oxygen transfer process initiated, magnetite reached its final oxidation state consisting of microwave-active Fe and Fe 3 C phases that continued coupling with microwaves along with the generated graphitic carbon to maintain the heat necessary to further reduce the generated tar and make additional gaseous products, as confirmed by XRD, Raman, and TGA analyses.

08 HYDROGEN↗
DOE OSTI2025

Sustainable upcycling of polyethylene waste to compatibilizers and valuable chemicals

Controllable functionalization of polyethylene (PE) waste could generate new polymeric materials that are generally difficult to manufacture sustainably while also addressing the growing plastics waste problem. However, these modifications remain challenging due to the inherent stability of the PE backbone. Non-thermal atmospheric plasma enables molecular activation under mild conditions while utilizing renewable energy but is primarily employed for surface modification, as plasmas do not penetrate the bulk of materials. Herein, controllable bulk oxidative functionalization of PE wax (PEW) and low-density PE (LDPE) of varying molecular weights was achieved, with up to 6 mol% oxygen incorporation, by manipulating melt viscosity. This functionalization was accomplished either through temperature adjustment or by introducing a melt viscosity modifier, removable via simple extraction methods, to reduce LDPE viscosity, enhance diffusion and chain mobility, and enable bulk oxidation. The oxidized LDPE induces compatibilization in blends of poly(lactic acid) (PLA) and LDPE with improved interfacial adhesion and mechanical properties, such as a 70% increase in elongation-at-break values vs. the control. These findings pave the way for catalyst-free upcycling of direct plastics waste and plastics waste-derived products, enabling the creation of high-value products across various markets.

Plastic upcycling↗
DOE OSTI2025

RB-TnSeq elucidates dicarboxylic-acid-specific catabolism in β-proteobacteria for improved plastic monomer upcycling

Dicarboxylic acids are key components of many polymers and plastics, making them a target for both engineered microbial degradation and sustainable bioproduction. In this study, we generated a comprehensive data set of functional evidence for the genetic basis of dicarboxylic and fatty acid metabolism using randomly barcoded transposon sequencing (RB-TnSeq). We identified four β-proteobacteria that displayed robust growth with dicarboxylic acid sole carbon source and cultured their mutant libraries with dicarboxylic and fatty acids with carbon chain lengths from C3 to C12. The resulting fitness data suggested that dicarboxylic and fatty acid metabolisms are largely distinct, and different sets of β-oxidation genes are required for catabolizing dicarboxylic versus fatty acids of the same carbon chain lengths. In addition, we identified transcriptional regulators and transporters with strong fitness phenotypes related to dicarboxylic acid utilization. In Ralstonia sp. UNC404CL21Col (R. CL21), we deleted two transcriptional repressors to improve its utilization of short-chain dicarboxylic acids. We exploited the diacid-utilizing catabolism of R. CL21 to upcycle a mock mixture of the dicarboxylic acids produced when polyethylene is oxidized. After introducing a heterologous indigoidine production pathway, this engineered Ralstonia produced 0.56 ± 0.02 g/L indigoidine from a mixture of dicarboxylic acids as a carbon source, demonstrating the potential of R. CL21 to upcycle plastic wastes to products derived from tricarboxylic acid (TCA) cycle intermediates. IMPORTANCE: Upcycling the carbon in plastic wastes to value-added products is a promising approach to address the plastic waste and climate crises, and dicarboxylic acid metabolism is an important facet of several approaches. Improving our understanding of the genetic basis of this metabolism has the potential to uncover new enzymes and genetic parts for engineered pathways involving dicarboxylic acids. Our data set is the most comprehensive interrogation of dicarboxylic acid catabolism to date, and this work will be of utility to researchers interested in both plastics bioproduction and upcycling applications.

Pearson, Allison N↗
DOE OSTI2025

Structure-dependent mechanisms for plastic degradation in the marine environment

The visible and invisible accumulation of waste plastic in our oceans is a consequence of rapidly increasing inputs and very slow degradation rates. In general, this combination of effects results in long residence times. Nevertheless, the abiological degradation rate of a specific synthetic plastic varies widely, depending on its structural characteristics at the molecular, mesoscopic, and macroscopic levels. This chapter summarizes factors that determine these rates of degradation, and describes their principal mechanisms, for several of the major types of waste plastic found in the oceans. Mechanical forces cause cracking and flaking that break macroplastics into microplastics and even smaller fragments with increasing surface-to-volume ratios. Chemical degradation rates increase with surface area, influenced by intrinsic variations in crystallinity and the presence of additives, as well as extrinsic factors such as temperature, pH, and UV light intensity. Since polyolefin-based plastics are less dense than seawater and lack hydrolysable bonds in their polymer backbones, they accumulate close to the surface of the ocean where photo-oxidation is the principal cause of C–C bond cleavage in the polymer backbone. In contrast, polyesters and polyamides are denser than seawater and they sink, experiencing less exposure to solar irradiation. However, they can also degrade by slow hydrolysis of the C–O or C–N bonds intrinsic to the polymer structures.

Maciulis, Nicholas A.↗
DOE OSTI2025

SEM/EBSD Characterization of Baffle-Former Bolts Designated for High Energy X-ray Microscopy Studies at the Advanced Photon Source

This report documents the microstructural and surface characterization of two high-fluence baffle-former bolts (BFBs) harvested from a commercial pressurized water reactor (PWR) after nearly four decades of service. These bolts experienced extreme conditions including high neutron fluence, elevated temperatures, corrosive primary water, and sustained mechanical loads, all of which contribute to degradation mechanisms such as irradiation-assisted stress corrosion cracking (IASCC). Using scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD), the study assessed bulk and near-surface microstructures, grain boundary characteristics, and in-service oxide layers. The results revealed significant differences between bolts exposed to 41 dpa and 29 dpa, including differences in recrystallization extent, deformation structures, and oxidation morphology. These findings establish critical baseline data for integration with advanced synchrotron-based high-energy X-ray microscopy (HEXM) and computational crystal plasticity models. Ultimately, the work supports improved mechanistic understanding and predictive capability regarding the long-term performance of reactor core internal components.

Lach, Tim [Oak Ridge National Laboratory (ORNL), O↗
DOE OSTI2022

More Powerful Twistron Carbon Nanotube Yarn Mechanical Energy Harvesters

We report that stretching a coiled carbon nanotube (CNT) yarn can provide large, reversible electrochemical capacitance changes, which convert mechanical energy to electricity. Here, it is shown that the performance of these “twistron” harvesters can be increased by optimizing the alignment of precursor CNT forests, plastically stretching the precursor twisted yarn, applying much higher tensile loads during precoiling twist than for coiling, using electrothermal pulse annealing under tension, and incorporating reduced graphene oxide nanoplates. The peak output power for a 1 and a 30 Hz sinusoidal deformation are 0.73 and 3.19 kW kg -1 , respectively, which are 24- and 13-fold that of previous twistron harvesters at these respective frequencies. This performance at 30 Hz is over 12-fold that of other prior-art mechanical energy harvesters for frequencies between 0.1 and 600 Hz. The maximum energy conversion efficiency is 7.2-fold that for previous twistrons. Twistron anode and cathode yarn arrays are stretched 180° out-of-phase by locating them in the negative and positive compressibility directions of hinged wine-rack frames, thereby doubling the output voltage and reducing the input mechanical energy.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Upcycling Polyethylene Waste into Hybrid Graphitic Porous Carbon Materials Used in High‐Performance Zinc‐Ion Hybrid Capacitors

Polyethylene (PE) waste is a challenge to upcycle into useful materials because this plastic tends to decompose into volatile compounds when heated at relatively low temperatures. In this work, mixtures of PE wastes into a hybrid graphitic porous carbon (HGPC) by a thermal oxidation pretreatment step, with assistance of an inert solid additive (KCl), to functionalize, crosslink, and stabilize the PE waste followed by carbonization and catalytic graphitization steps with a potassium carbonate catalyst, are upcycled. The PE waste‐derived HGPC (PW‐HGPC) has a hybrid structure composed of graphene‐like carbon nanosheets grown on the surface of carbon particles, high porosity with specific surface area, up to 1,763 m 2 g −1 , and good graphitic degree with average Raman I 2D / I G ratios of 0.53. When used as cathode material for zinc‐ion hybrid capacitors, this PW‐HGPC exhibits an excellent specific capacity, up to 126.7 mAh g −1 , at high mass loading of 10 mg cm −2 . Moreover, PW‐HGPC exhibits remarkable cycling stability with capacity retention of >94% after 10 000 cycles. Additionally, the KCl is recycled and reused over five times. This method provides a new solution for upcycling PE wastes into high value‐added carbon materials, not only for zinc‐ion hybrid capacitors but also for other electrochemical energy storage device applications.

hybrid graphitic porous carbon↗
DOE OSTI2024

Corrosion Engineering of Part‐Per‐Million Single Atom Pt 1 /Ni(OH) 2 Electrocatalyst for PET Upcycling at Ampere‐Level Current Density

The plastic waste issue has posed a series of formidable challenges for the ecological environment and human health. While conventional recycling strategies often lead to plastic down-cycling, the electrochemical strategy of recovering valuable monomers enables an ideal, circular plastic economy. Here a corrosion synthesized single atom Pt 1 /Ni(OH) 2 electrocatalyst with part-per-million noble Pt loading for highly efficient and selective upcycling of polyethylene terephthalate (PET) into valuable chemicals (potassium diformate and terephthalic acid) and green hydrogen is reported. Electro-oxidation of PET hydrolysate, ethylene glycol (EG), to formate is processed with high Faraday efficiency (FE) and selectivity (>90%) at the current density close to 1000 mA cm −2 (1.444 V vs RHE). The in situ spectroscopy and density functional theory calculations provide insights into the mechanism and the understanding of the high efficiency. Remarkably, the electro-oxidation of EG at the ampere-level current density is also successfully illustrated by using a membrane-electrode assembly with high FEs to formate integrated with hydrogen production for 500 h of continuous operation. In conclusion, this process allows valuable chemical production at high space-time yield and is highly profitable (588–700 $\$$ ton −1 PET), showing an industrial perspective on single-atom catalysis of electrochemical plastic upcycling.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Surface Integrity and Oxidation of a Powder Metallurgy Ni-Based Superalloy Treated by Laser Shock Peening

Laser shock peening is a mechanical surface treatment which can induce large compressive residual stresses and microstructural changes in the material by using repetitive shocks from laser pulses. In this work, the surface integrity (surface microstructure, topography, hardness and residual stress) of a laser shock peening treated powder metallurgy Ni-based superalloy was investigated. Laser shock peening treatment introduces large plastic deformation especially at a depth of about 100 μm from the surface, which increases the local hardness. The residual stress from the surface to the interior of the sample was investigated by synchrotron X-ray diffraction. The maximum compressive stress reaches 400 MPa at the surface, while the depth of the compressive stress is about 0.7 mm. Lastly, the oxidation behavior of the treated and untreated samples was evaluated by thermal exposure at 700°C for 312 h. The LSP treatment decreased the thickness of oxide layer, thereby showing improved oxidation resistance.

36 MATERIALS SCIENCE↗