Search NASA⌕ Search

SEARCH · Search NASA

Results for “power conversion efficiency”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

Can quantum coherent solar cells break detailed balance?

Carefully engineered coherent quantum states have been proposed as a design attribute that is hypothesized to enable solar photovoltaic cells to break the detailed balance (or radiative) limit of power conversion efficiency by possibly causing radiative recombination to be suppressed. However, in full compliance with the principles of statistical mechanics and the laws of thermodynamics, specially prepared coherent quantum states do not allow a solar photovoltaic cell—a quantum threshold energy conversion device—to exceed the detailed balance limit of power conversion efficiency. At the condition given by steady-state open circuit operation with zero nonradiative recombination, the photon absorption rate (or carrier photogeneration rate) must balance the photon emission rate (or carrier radiative recombination rate) thus ensuring that detailed balance prevails. Quantum state transitions, entropy-generating hot carrier relaxation, and photon absorption and emission rate balancing are employed holistically and self-consistently along with calculations of current density, voltage, and power conversion efficiency to explain why detailed balance may not be violated in solar photovoltaic cells.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Conversion efficiency improvement of ELO GaAs solar cell, deposited on water soluble sacrificial buffer

Here, we demonstrate the improvement of power conversion efficiency of an epitaxially-lifted-off single junction GaAs solar cell deposited on a water-soluble sacrificial buffer architecture by introducing an additional germanium (Ge) interlayer between GaAs and the fluoride buffer. The epitaxial lift-off (ELO) technique has been extensively used to separate III-V device layers from their single crystal GaAs substrates. However, conventional ELO requires the use of concentrated hydrofluoric acid (HF) for extended times to etch out the sacrificial layer, subsequently degrading the surface roughness of the parent wafer. As a result, the wafer has to undergo expensive and intensive chemical mechanical polishing (CMP) processes, costing about 25% of a pristine 6-inch GaAs substrate. In our previous work, we demonstrated a method to eliminating the need for CMP post-processing by using water-assisted ELO (H 2 O-ELO). A water-soluble, 3-layer buffer architecture was developed using alkaline earth compounds. However, devices suffered low performance due to a high defect density in the GaAs active layers. A Ge interlayer was introduced to provide a more favorable surface energy for GaAs growth, which leads to an improvement of GaAs crystal quality. The Ge deposition conditions were optimized to achieve a high-quality Ge layer on triple-layer fluoride buffer. Single junction GaAs devices fabricated on Ge/(Ca,Sr)F 2 /BaF 2 /(Ca,Sr)F 2 showed improvement of solar cell performance parameters featuring increases in V oc by 23.7%, and fill factor (F.F.) by 4.9%, which results in an overall improvement of power conversion efficiency from 10.3% to 12.69%.

14 SOLAR ENERGY↗

Intermediate-phase engineering via dimethylammonium cation additive for stable perovskite solar cells

Achieving the long-term stability of perovskite solar cells is arguably the most important challenge required to enable widespread commercialization. Understanding the perovskite crystallization process and its direct impact on device stability is critical to achieving this goal. The commonly employed dimethyl-formamide/dimethyl-sulfoxide solvent preparation method results in a poor crystal quality and microstructure of the polycrystalline perovskite films. In this work, we introduce a high-temperature dimethyl-sulfoxide-free processing method that utilizes dimethylammonium chloride as an additive to control the perovskite intermediate precursor phases. By controlling the crystallization sequence, we tune the grain size, texturing, orientation (corner-up versus face-up) and crystallinity of the formamidinium (FA)/caesium (FA) y Cs 1-y Pb(I x Br 1-x )3 perovskite system. A population of encapsulated devices showed improved operational stability, with a median T80 lifetime (the time over which the device power conversion efficiency decreases to 80% of its initial value) for the steady-state power conversion efficiency of 1,190 hours, and a champion device showed a T80 of 1,410 hours, under simulated sunlight at 65 degrees C in air, under open-circuit conditions. In conclusion, this work highlights the importance of material quality in achieving the long-term operational stability of perovskite optoelectronic devices.

14 SOLAR ENERGY↗

Beyond Fullerenes: Indacenodithiophene-Based Organic Charge-Transport Layer toward Upscaling of Low-Cost Perovskite Solar Cells

Phenyl-C 61 -butyric acid methyl ester (PCBM) is universally used as the electron-transport layer (ETL) in the low-cost inverted planar structure of perovskite solar cells (PeSCs). PCBM brings tremendous challenges in upscaling of PeSCs using industry-relevant methods due to its aggregation behavior, which undermines the power conversion efficiency and stability. Herein, we highlight these, seldom reported, challenges with PCBM. Moreoever, we investigate the potential of nonfullerene indacenodithiophene (IDT)-based molecules by employing a commercially available variant, 3,9- bis(2-methylene-(3-(1,1-dicyanomethylene)-indanone))- 5,5,11,11-tetrakis(4-hexylphenyl)-dithieno[2,3-d:2',3'-d']-s-indaceno[1,2-b:5,6-b'] dithiophene (ITIC), as a PCBM replacement in ambient-processed PeSCs. Films fabrication by laboratory-based spin-coating and industry-relevant slot-die coating methods are compared. While similar power-conversion efficiencies are achieved with both types of ETL in a simple device structure fabricated by spin-coating, the nanofibriller morphology of ITIC compared to the aggregated morphology of PCBM films enables improved mechanical integrity and stability of ITIC devices. Upon slot-die coating, the aggregation of PCBM is exacerbated, leading to significantly lower power-conversion efficiency of devices than spin-coated PCBM as well as slot-diecoated ITIC devices. Our findings clearly suggest that IDT-based molecules have great potential as an ETL in PeSCs, offering superior properties and upscaling compatibility than PCBM. Thus, we present a short summary of recently emerged nonfullerene IDT-based molecules from the field of organic solar cells and discuss their scope in PeSCs as electron or holetransport layer.

42 ENGINEERING↗

Carbazole-Based Hole Transport Polymer for Methylammonium-Free Tin-Lead Perovskite Solar Cells with Enhanced Efficiency and Stability

As the most commonly used hole transport material (HTM) in tin-lead (Sn-Pb) perovskite solar cells (PSCs), poly(3,4-ethylenedioxythiophene) polystyrenesulfonate (PEDOT:PSS) limits the power conversion efficiency (PCE) and stability of the PSCs due to its acidic characteristics. Herein, an easily synthesized polymer HTM poly[(phenyl)imino[9-(2-ethylhexyl)carbazole]-2,7-diyl] (CzAn) with a shallow highest occupied molecular orbital (HOMO) level of -4.95 eV is used in a p-i-n structure, methylammonium-free, Sn-Pb PSC to replace PEDOT:PSS. Upon optimization using doping and surface engineering, high quality Sn-Pb PSCs could be successfully fabricated, boosting the PCE to 22.6% (stabilized PCE of 21.3%) compared with 21.2% for PEDOT:PSS. The perovskite films prepared on the modified CzAn HTM possess improved crystallinity, reduced trap-state density, and larger carrier mobility resulting in PSCs with greatly improved stability.

carrier mobility↗

High performance dye-sensitized solar cells using graphene modified fluorine-doped tin oxide glass by Langmuir–Blodgett technique

Since the introduction of dye-sensitized solar cells (DSSCs) with low fabrication cost and high power conversion efficiency, extensive studies have been carried out to improve the charge transfer rate and performance of DSSCs. In this paper, we present DSSCs that use surface modified fluorine-doped tin oxide (FTO) substrates with reduced graphene oxide (r-GO) sheets prepared using the Langmuir–Blodgett (LB) technique to decrease the charge recombination at the TiO{sub 2}/FTO interface. R-GO sheets were excellently attached on FTO surface without physical deformations such as wrinkles; effects of the surface coverage of r-GO on the DSSC performance were also investigated. By using graphene modified FTO substrates, the resistance at the interface of TiO{sub 2}/FTO was reduced and the power conversion efficiency was increased to 8.44%. - Graphical abstract: DSSCs with graphene modified FTO glass were fabricated with the Langmuir Blodgett technique. GO sheets were transferred to FTO at various surface pressures in order to change the surface density of graphene and the highest power conversion efficiency of the DSSC was 8.44%. - Highlights: • By LB technique, r-GO sheets were coated on FTO without physical deformation. • DSSCs were fabricated with, r-GO modified FTO substrates. • With surface modification by r-GO, the interface resistance of DSSC decreased. • Maximum PCE of the DSSC was increased up to 8.44%.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Side chain engineering of poly-thiophene and its impact on crystalline silicon based hybrid solar cells

The influence of ether groups in the side chain of spin coated regioregular polythiophene derivatives on the polymer layer formation and the hybrid solar cell properties was investigated using electrical, optical, and X-ray diffraction experiments. The polymer layers are of high crystallinity but the polymer with 3 ether groups in the side chain (P3TOT) did not show any vibrational fine structure in the UV-Vis spectrum. The presence of ether groups in the side chains leads to better adhesion resulting in thinner and more homogeneous polymer layers. This, in turn, enhances the electronic properties of the planar c-Si/poly-thiophene hybrid solar cell. We find that the power conversion efficiency increases with the number of ether groups in the side chains, and a maximum power conversion efficiency of η = 9.6% is achieved even in simple planar structures.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Perovskite on Silicon Tandem Solar Cells

Since installing solar panels costs more than the panels themselves, it is critically important to improve the efficiency of the panels so that fewer panels need to be installed. More than 90% of all panels being manufactured are made with silicon solar cells. The most promising approach to reach 27% is to upgrade the panels by adding a second set of cells with a larger band gap that can harvest the higher energy photons in the visible spectrum and generate a higher voltage than silicon is capable of generating. Perovskite semiconductors are very promising for low-cost tandems because they have high band gaps, can be rapidly printed from solutions and have been used to make 25% efficient cells by themselves. If we show that it is possible to make stable tandems with 30% efficiency using materials that could be deposited at low cost and that the energy yield will not be compromised, then private companies would be able to raise the capital needed to manufacture this technology. The main metrics for this project are the power conversion efficiency of a lab-scale perovskite/silicon tandem and the ability to maintain a high power conversion efficiency in perovskite solar cells after accelerated operational stability testing under maximum power point at elevated temperature and 1 sun illumination. In short, this project demonstrates improvements to the perovskite absorber layer, contacts for the perovskite solar cell, and transparent oxide layers for window electrodes to achieve tandem efficiencies of 25% after one year and 27% after two years. By the end of the project, we identify strategies to further improve light management in the tandem devices and outline a pathway to reach 30%.In parallel, stability testing is conducted to evaluate said absorber and contact layers in the perovskite top cell, demonstrating 1000 hours of operation with less than 10% degradation at 1 sun. Our work on this project has made a leading impact on the development of perovskite/silicon tandems. The triple halide perovskite that we developed using iodide, bromide, and chloride and published in Science in March 2020 has received significant interest from other experts in the field at conferences. We took a silicon bottom cell with 21% efficiency, a technology that is responsible for a $30 billion market, and improved it by 30% relative. In addition, we have demonstrated impressive stability of our perovskite semitransparent top cells used in the tandems, showing for the first time packaged devices that pass a variety of IEC stability tests including damp heat, temperature cycling, and UV exposure tests.

14 SOLAR ENERGY↗

Control of morphology and function of low band gap polymer–bis-fullerene mixed heterojunctions in organic photovoltaics with selective solvent vapor annealing

We reported how by replacing PCBM with a bis-adduct fullerene (i.e. ICBA) we significantly improve the open circuit voltage (VOC) and power conversion efficiency (PCE) in P3HT bulk heterojunctions. But, for the most promising low band-gap polymer (LBP) systems, replacing PCBM with ICBA results in very poor shortcircuit current (JSC) and PCE although the VOC is significantly improved. Therefore, in this work, we have completed small angle neutron scattering and neutron reflectometry experiments to study the impact of post-deposition solvent annealing (SA) with control of solvent quality on the morphology and performance of LBP bis-fullerene BHJ photovoltaics. Our results show that SA in a solvent that is selective for the LBP results in a depletion of bis-fullerene near the air surface, which limits device performance. SA in a solvent vapor which has similar solubility for polymer and bis-fullerene results in a higher degree of polymer ordering, bis-fullerene phase separation, and segregation of the bis-fullerene to the air surface, which facilitates charge transport and increases power conversion efficiency (PCE) by 100%. The highest degree of polymer ordering combined with significant bis-fullerene phase separation and segregation of bis-fullerene to the air surface is obtained by SA in a solvent vapor that is selective for the bis-fullerene. The resultant morphology increases PCE by 190%. These results indicate that solvent annealing with judicious solvent choice provides a unique tool to tune the morphology of LBP bisfullerene BHJ system, providing sufficient polymer ordering, formation of a bis-fullerene pure phase, and segregation of bis-fullerene to the air surface to optimize the morphology of the active layer. Furthermore, this process is broadly applicable to improving current disappointing LBP bis-fullerene systems to optimize their morphology and OPV performance post-deposition, including higher VOC and power conversion efficiency.

36 MATERIALS SCIENCE↗

Chapter 3: Thin-Film Colloidal Quantum Dot Solar Cells

In under a decade, progress in quantum dot (QD) solar cell design and fabrication have increased PbS QD solar cell efficiencies from 3% to 11.3%. Such solar cells based on colloidal quantum dots offer the potential for a higher limiting power conversion efficiency through the enhancement of multiple exciton generation (MEG). In the MEG process, one photon produces two or more excitons that can contribute to power generation when the photon energy exceeds the semiconductor bandgap. The efficiency of the MEG process has also increased through the design and fabrication of new nanostructures. The fast pace at which QD devices are improving and the potential for a higher limiting efficiency - as MEG can increase the limiting power conversion efficiency (PCE) for a single-junction solar cell from 33% to ~ 45% - demonstrate the large potential of these systems.

14 SOLAR ENERGY↗

Self-ordering anodized nanotubes: Enhancing the performance by surface plasmon for dye-sensitized solar cell

In the present work, electrochemical anodization has been used to prepare uniform TiO{sub 2} nanotube array photoelectrode. The average internal diameter, tube length and wall thickness of the optimized morphology is {approx}180 nm, 14 {mu}m and 10 nm, respectively. It was found that the tube diameter increases with the anodization voltage. Diffraction data reveals that the nanotubes consist solely of anatase phase. Back illuminated geometry of dye-sensitized solar cell (DSSC), with nanotubes grown at 60 V for 2 h, gave a cell performance of 4.5%. TiO{sub 2} nanotubes are loaded with silver (Ag) nanoparticles synthesized by a hydrothermal route. The Ag particle size is controlled resulting in solar conversion efficiency to increase by 22%. The DSSC based on TiO{sub 2} nanotube with Ag nanoparticles shows power conversion efficiency of 5.5%. Detailed characterization are performed, presented and discussed. - Graphical abstract: Enhanced solar conversion efficiency of dye-sensitized solar cells by decorating TiO{sub 2} nanotube array with Ag nanoparticles. Highlights: Black-Right-Pointing-Pointer Uniform array of TiO{sub 2} nanotubes synthesized via electrochemical anodization. Black-Right-Pointing-Pointer Back illuminated DSSC gave a cell performance of 4.5%. Black-Right-Pointing-Pointer TiO{sub 2} nanotubes are loaded with Ag nanoparticles, which increased the power conversion efficiency to 5.5%.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Efficient second- and third-harmonic radiation generation from relativistic laser-plasma interactions

We propose an idea to enhance the efficiency of second- and third-harmonic generation by considering the amplitude-modulation of the fundamental laser pulse. A short-pulse laser of finite spot size is modeled as amplitude modulated in time. Amplitude-modulation of fundamental laser contributes in quiver velocity of the plasma electrons and produces the strong plasma-density perturbations, thereby increase in current density at second- and third-harmonic frequency. In a result, the conversion efficiency of harmonic generation increases significantly. Power conversion efficiency of harmonic generation process is the increasing function of the amplitude-modulation parameter of the fundamental laser beam. Harmonic power generated by an amplitude modulated laser is many folds higher than the power obtained in an ordinary case.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Tandem Polymer Solar Cells Featuring a Spectrally Matched Low-Bandgap Polymer

Tandem solar cells provide an effective way to harvest a broader spectrum of solar radiation by combining two or more solar cells with different absorption bands. However, for polymer solar cells, the performance of tandem devices lags behind single-layer solar cells mainly due to the lack of a suitable low-bandgap polymer. Here, we demonstrate highly efficient single and tandem polymer solar cells featuring a low-bandgap conjugated polymer (PBDTT-DPP: bandgap, {approx}1.44 eV). A single-layer device based on the polymer provides a power conversion efficiency of {approx}6%. When the polymer is applied to tandem solar cells, a power conversion efficiency of 8.62% is achieved, which is, to the best of our knowledge, the highest certified efficiency for a polymer solar cell to date.

14 SOLAR ENERGY↗

Solar thermophotovoltaic system using nanostructures

This paper presents results on a highly efficient experimental solar thermophotovoltaic (STPV) system using simulated solar energy. An overall power conversion efficiency of 6.2% was recorded under solar simulation. This was matched with a thermodynamic model, and the losses within the system, as well as a path forward to mitigate these losses, have been investigated. The system consists of a planar, tungsten absorbing/emitting structure with an anti-reflection layer coated laser-microtextured absorbing surface and single-layer dielectric coated emitting surface. A GaSb PV cell was used to capture the emitted radiation and convert it into electrical energy. This simple structure is both easy to fabricate and temperature stable, and contains no moving parts or heat exchange fluids.

14 SOLAR ENERGY↗

A long-pulse repetitive operation magnetically insulated transmission line oscillator

The improved magnetically insulated transmission line oscillator (MILO) is a gigawatt-class L-band high power microwave tube. It has allowed us to generate 3.1 GW pulse of 40 ns duration in the single-pulse operation and 500 MW pulse of 25 ns duration in the repetition rate operation. However, because of the severe impedance mismatch, the power conversion efficiency is only about 4% in the repetition rate operation. In order to eliminate the impedance mismatch and obtain repetitive long-pulse high-power microwave (HPM), a series of experiments are carried out and the recent progress is presented in this paper. In the single-pulse operation, when the diode voltage is 466 kV and current is 41.6 kA, the radiated microwave power is above 2.2 GW, the pulse duration is above 102 ns, the microwave frequency is about 1.74 GHz, and the power conversion efficiency is about 11.5%. In the repetition rate operation, under the condition of the diode voltage about 400 kV, beam current about 38 kA, the radiated microwave power is about 1.0 GW, the pulse duration is about 85 ns. Moreover, the radiated microwave power and the pulse duration decline little by little when the shot numbers increase gradually. The experimental results show that the impedance matching is a vital factor for HPM systems and one of the major technical challenges is to improve the cathode for the repetition rate operation MILO.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Quantum dot cosensitized solar cell based on PMOT@CdSe@ZnO core shell nanostructures with dual emission

Quantum dot sensitized solar cell based on poly(3-methoxythiophene) (PMOT)@CdSe@ZnO core shell nanostructure were synthesized where PMOT serves as hole transport material, CdSe acts as a photosensitizer which enhances visible range absorption and also helps in injection of electrons from PMOT to ZnO where ZnO provides channel for efficient electron transport. The properties of the device were assessed with and without CdSe quantum dots and effect of annealing was also observed on the device. After the addition of CdSe QDs, the visible light absorption of PMOT@ZnO was enhanced due to increase in surface area. PMOT@CdSe@ZnO exhibited dual emission, where CdSe and ZnO exhibited visible and UV emission respectively. The interface formed between PMOT and CdSe improves the charge separation. The better photovoltaic measurement of PMOT@CdSe@ZnO over CdSe@ZnO indicates that PMOT efficiently dissociate excitons at interface and suppress the interfacial charge recombination. A power conversion efficiency of 0.989% was attained for the device PMOT@CdSe@ZnO with V{sub oc}=0.56 V and J{sub sc}=2.5 mA/cm{sup 2}. Upon annealing, the efficiency of the device was enhanced to 1.1609% with V{sub oc}=0.58, J{sub sc}=3.2 mA/cm{sup 2}. - Highlights: • Synthesized PMOT@CdSe@ZnO is biluminescent in nature. • A power conversion efficiency of 0.989% was achieved with PMOT@CdSe@ZnO device which is superior to CdSe@ZnO and PMOT@ZnO. • Upon annealing, an efficiency of 1.1609% was achieved for device PMOT@CdSe@ZnO.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Tin–Lead Alloying for Efficient and Stable All-Inorganic Perovskite Solar Cells

Cesium containing all-inorganic perovskites have received considerable interest in photovoltaics research because of their potential for improved stability compared to their organic-inorganic hybrid counterparts. However, the inorganic perovskites studied thus far still suffer from lower power conversion efficiency and long-term instability, due to an unfavorable bandgap and either phase instability or air-sensitivity. Herein, A strategy to mitigate these concerns is investigated by alloying tin and lead on the B site to form tin-lead alloyed low-bandgap (~1.34 eV) inorganic CsSn 0.3 Pb 0.7 I 3 perovskites. Solar cells made using this material in an inverted full-structured architecture with a PEDOT:PSS hole transport materials (HTM) attain power conversion efficiency (PCE) up to 9.41% (stabilized PCE 7.23%). Furthermore, a simple HTM-free device without PEDOT:PSS layer is demonstrated more stable than the full-structured device and exhibits a PCE of 7.60% (stabilized PCE 7.31%) – the highest efficiency to date for an inorganic perovskite with a bandgap below 1.40 eV. This simplified device structure shows good reproducibility and stability. Finally, this work provides a possible route for fabricating low-cost, high stability devices with competitive efficiencies.

14 SOLAR ENERGY↗

Equally high efficiencies of organic solar cells processed from different solvents reveal key factors for morphology control

The power conversion efficiency of organic solar cells (OSCs) is exceeding 20%, an advance in which morphology optimization has played a significant role. It is generally accepted that the processing solvent (or solvent mixture) can help optimize morphology, impacting the OSC efficiency. Here we develop OSCs that show strong tolerance to a range of processing solvents, with all devices delivering high power conversion efficiencies around 19%. By investigating the solution states, the film formation dynamics and the characteristics of the processed films both experimentally and computationally, we identify the key factors that control morphology, that is, the interactions between the side chains of the acceptor materials and the solvent as well as the interactions between the donor and acceptor materials. Our work provides new understanding on the long-standing question of morphology control and effective guides to design OSC materials towards practical applications, where green solvents are required for large-scale processing.

14 SOLAR ENERGY↗