Search NASA⌕ Search

SEARCH · Search NASA

Results for “programmable”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

Programmable, secondary frequency standard based infrared synthesizer using tunable lead-salt diode lasers

Quantum phase noise limited Lorentzian power spectral densities were achieved with tunable lead-salt diode lasers. Linewidths as narrow as 22 kHz were observed. A truly programmable infrared synthesizer was produced by frequency-offset-locking the tunable diode lasers to the combination of a stable CO2 (or CO) reference laser and a programmable microwave frequency synthesizer. Absolute frequency accuracy and reproducibility of about + or - 30 kHz (0.000001 kaysers) relative to the primary Cs frequency standard may now be obtained with this technique.

Freed, C.↗
NASA NTRS1985

Planning fuel-conservative descents in an airline environmental using a small programmable calculator: Algorithm development and flight test results

A simple, airborne, flight-management descent algorithm was developed and programmed into a small programmable calculator. The algorithm may be operated in either a time mode or speed mode. The time mode was designed to aid the pilot in planning and executing a fuel-conservative descent to arrive at a metering fix at a time designated by the air traffic control system. The speed model was designed for planning fuel-conservative descents when time is not a consideration. The descent path for both modes was calculated for a constant with considerations given for the descent Mach/airspeed schedule, gross weight, wind, wind gradient, and nonstandard temperature effects. Flight tests, using the algorithm on the programmable calculator, showed that the open-loop guidance could be useful to airline flight crews for planning and executing fuel-conservative descents.

Knox, C. E.↗
NASA NTRS1986

Microcomputer-based programmable optical signal processor

A microcomputer-based real-time programmable optical signal processing system utilizing a magneto-optic spatial light modulator (MOSLM) and a liquid crystal light valve (LCLV) is described. This system can perform a myriad of complicated optical operations, such as image correlation, image subtraction, and matrix multiplication. Its important asserts are its programmability and the capability of real-time addressing. These are important for telerobotic vision in space automation applications. Design specifications and suggestions for practical implementation of the system are discussed. Some preliminary experimental demonstrations are conducted to demonstrate applications of the proposed system to image correlation for optical pattern recognition, image subtraction for lC chip inspection, and matrix multiplication for optical computing.

Yu, F. T. S.↗
NASA NTRS1986

Evaluation of automated decisionmaking methodologies and development of an integrated robotic system simulation. Appendix B: ROBSIM programmer's guide

The purpose of the Robotic Simulation (ROBSIM) program is to provide a broad range of computer capabilities to assist in the design, verification, simulation, and study of robotic systems. ROBSIM is programmed in FORTRAM 77 and implemented on a VAX 11/750 computer using the VMS operating system. The programmer's guide describes the ROBSIM implementation and program logic flow, and the functions and structures of the different subroutines. With the manual and the in-code documentation, an experienced programmer can incorporate additional routines and modify existing ones to add desired capabilities.

Haley, D. C.↗
NASA NTRS1988

Programmable Pulser

User controls number of clock pulses to prevent burnout. New digital programmable pulser circuit in three formats; freely running, counted, and single pulse. Operates at frequencies up to 5 MHz, with no special consideration given to layout of components or to terminations. Pulser based on sequential circuit with four states and binary counter with appropriate decoding logic. Number of programmable pulses increased beyond 127 by addition of another counter and decoding logic. For very large pulse counts and/or very high frequencies, use synchronous counters to avoid errors caused by propagation delays. Invaluable tool for initial verification or diagnosis of digital or digitally controlled circuity.

Baumann, Eric↗
NASA NTRS1986

RT_BUILD: An expert programmer for implementing and simulating Ada real-time control software

The RT BUILD is an expert control system programmer that creates real-time Ada code from block-diagram descriptions of control systems. Since RT BUILD embodies substantial knowledge about the implementation of real-time control systems, it can perform many, if not most of the functions normally performed by human real-time programmers. Though much basic research was done in automatic programming, RT BUILD appears to be the first application of this research to an important problem in flight control system development. In particular, RT BUILD was designed to directly increase productivity and reliability for control implementations of large complex systems.

Lehman, Larry L.↗
NASA NTRS1989

Structural Tailoring of Advanced Turboprops (STAT) programmer's manual

The Structural Tailoring of Advanced Turboprops (STAT) computer program was developed to perform numerical optimizations on highly swept propfan blades. This manual describes the functionality of the STAT system from a programmer's viewpoint. It provides a top-down description of module intent and interaction. The purpose of this manual is to familiarize the programmer with the STAT system should he/she wish to enhance or verify the program's function.

Brown, K. W.↗
NASA NTRS1988

Feedforward, high density, programmable read only neural network based memory system

Neural network-inspired, nonvolatile, programmable associative memory using thin-film technology is demonstrated. The details of the architecture, which uses programmable resistive connection matrices in synaptic arrays and current summing and thresholding amplifiers as neurons, are described. Several synapse configurations for a high-density array of a binary connection matrix are also described. Test circuits are evaluated for operational feasibility and to demonstrate the speed of the read operation. The results are discussed to highlight the potential for a read data rate exceeding 10 megabits/sec.

Daud, Taher↗
NASA NTRS1988

Programmable synaptic chip for electronic neural networks

A binary synaptic matrix chip has been developed for electronic neural networks. The matrix chip contains a programmable 32X32 array of 'long channel' NMOSFET binary connection elements implemented in a 3-micron bulk CMOS process. Since the neurons are kept off-chip, the synaptic chip serves as a 'cascadable' building block for a multi-chip synaptic network as large as 512X512 in size. As an alternative to the programmable NMOSFET (long channel) connection elements, tailored thin film resistors are deposited, in series with FET switches, on some CMOS test chips, to obtain the weak synaptic connections. Although deposition and patterning of the resistors require additional processing steps, they promise substantial savings in silicon area. The performance of synaptic chip in a 32-neuron breadboard system in an associative memory test application is discussed.

Moopenn, A.↗
NASA NTRS1990

Programmable Analog Memory Resistors For Electronic Neural Networks

Electrical resistance of new solid-state device altered repeatedly by suitable control signals, yet remains at steady value when control signal removed. Resistance set at low value ("on" state), high value ("off" state), or at any convenient intermediate value and left there until new value desired. Circuits of this type particularly useful in nonvolatile, associative electronic memories based on models of neural networks. Such programmable analog memory resistors ideally suited as synaptic interconnects in "self-learning" neural nets. Operation of device depends on electrochromic property of WO3, which when pure is insulator. Potential uses include nonvolatile, erasable, electronically programmable read-only memories.

Ramesham, Rajeshuni↗
NASA NTRS1989

A programmable image compression system

A programmable image compression system which has the necessary flexibility to address diverse imaging needs is described. It can compress and expand single frame video images (monochrome or color) as well as documents and graphics (black and white or color) for archival or transmission applications. Through software control, the compression mode can be set for lossless or controlled quality coding; the image size and bit depth can be varied; and the image source and destination devices can be readily changed. Despite the large combination of image data types, image sources, and algorithms, the system provides a simple consistent interface to the programmer. This system (OPTIPAC) is based on the TITMS320C25 digital signal processing (DSP) chip and has been implemented as a co-processor board for an IBM PC-AT compatible computer. The underlying philosophy can readily be applied to different hardware platforms. By using multiple DSP chips or incorporating algorithm specific chips, the compression and expansion times can be significantly reduced to meet performance requirements.

Farrelle, Paul M.↗
NASA NTRS1989

PIPOR - A Programme for International Polar Oceans Research

The Programme for International Polar Oceans Research is accepted as a part of the ERS-1 mission which will be initiated with the launch of the ERS-1 earth observation satellite by the European Space Agency in 1990. It is a bipolar program with participation by institutions engaged in studies of the atmosphere-ocean-sea ice interaction and the application of remote sensing data for operational uses. The program objectives are to develop the application of microwave data for studies and modeling of sea ice dynamics and for operational uses in sea ice infested areas. As such, it is closely connected with ongoing and forthcoming research in the Arctic and the Antarctic. With sea ice being a sensitive indicator of climate perturbations, PIPOR addresses objectives of the World Climate Research Programme.

Gudmandsen, P.↗
NASA NTRS1991

Programmable digital modem

The design of the Programmable Digital Modem (PDM) is outlined. The PDM will be capable of operating with numerous modulation techniques including: 2-, 4-, 8- and 16-ary phase shift keying (PSK), minimum shift keying (MSK), and 16-ary quadrature amplitude modulation (QAM), with spectral occupancy from 1.2x to 2x the data symbol rate. It will also be programmable for transmission rates ranging from 2.34 to 300 Mbit/s, where the maximum symbol rate is 75 Msymbol/s. Furthermore, these parameters will be executable in independent burst, dependent burst, or continuous mode. In dependent burst mode the carrier and clock oscillator sources are common from burst to burst. To achieve as broad a set of requirements as these, it is clear that the essential signal processing must be digital. In addition, to avoid hardware changes when the operational parameters are changed, a fixed interface to an analog intermediate frequency (IF) is necessary for transmission; and, common system level architectures are necessary for the modulator and demodulator. Lastly, to minimize size and power, as much of the design as possible will be implemented with application specific integrated circuit (ASIC) chips.

Poklemba, John J.↗
NASA NTRS1992

Digital tracking loops for a programmable digital modem

In this paper, an analysis and hardware emulation of the tracking loops for a very flexible programmable digital modem (PDM) will be presented. The modem is capable of being programmed for 2, 4, 8, 16-PSK, 16-QAM, MSK, and Offset-QPSK modulation schemes over a range of data rates from 2.34 to 300 Mbps with programmable spectral occupancy from 1.2 to 1.8 times the symbol rate; these operational parameters are executable in burst or continuous mode. All of the critical processing in both the modulator and demodulator is done at baseband with very high-speed digital hardware and memory. Quadrature analog front-ends are used for translation between baseband and the IF center frequency. The modulator is based on a table lookup approach, where precomputed samples are stored in memory and clocked out according to the incoming data pattern. The sample values are predistorted to counteract the effects of the other filtering functions in the link as well as any transmission impairments. The demodulator architecture was adapted from a joint estimator-detector (JED) mathematical analysis. Its structure is applicable to most signalling formats that can be represented in a two-dimensional space. The JED realization uses interdependent, mutually aiding tracking loops with post-detection data feedback. To expedite and provide for more reliable synchronization, initial estimates for these loops are computed in a parallel acquisition processor. The cornerstone of the demodulator realization is the pre-averager received data filter which allows operation over a broad range of data rates without any hardware changes and greatly simplifies the implementation complexity. The emulation results confirmed tracking loop operation over the entire range of operational parameters listed above, as well as the capability of achieving and maintaining synchronization at BER's in excess of 10(exp -1). The emulation results also showed very close agreement with the tracking loop analysis, and validated the resolution apportionment of the various hardware elements in the tracking loops.

Poklemba, John J.↗
NASA NTRS1993

MASTRE trajectory code update to automate flight trajectory design, performance predictions, and vehicle sizing for support of shuttle and shuttle derived vehicles: Programmers manual

The information required by a programmer using the Minimum Hamiltonian AScent Trajectory Evaluation (MASTRE) Program is provided. This document enables the programmer to either modify the program or convert the program to computers other than the VAX computer. Documentation for each subroutine or function based on providing the definitions of the variables and a source listing are included. Questions concerning the equations, techniques, or input requirements should be answered by either the Engineering or User's manuals. Three appendices are also included which provide a listing of the Root-Sum-Square (RSS) program, a listing of subroutine names and definitions used in the MASTRE User Friendly Interface Program, and listing of the subroutine names and definitions used in the Mass Properties Program. The RSS Program is used to aid in the performance of dispersion analyses. The RSS program reads a file generated by the MASTRE Program, calculates dispersion parameters, and generates output tables and output plot files. UFI Program provides a screen user interface to aid the user in providing input to the model. The Mass Properties Program defines the mass properties data for the MASTRE program through the use of user interface software.

Source record↗
NASA NTRS1990

Auto-programmable impulse neural circuits

Impulse neural networks use pulse trains to communicate neuron activation levels. Impulse neural circuits emulate natural neurons at a more detailed level than that typically employed by contemporary neural network implementation methods. An impulse neural circuit which realizes short term memory dynamics is presented. The operation of that circuit is then characterized in terms of pulse frequency modulated signals. Both fixed and programmable synapse circuits for realizing long term memory are also described. The implementation of a simple and useful unsupervised learning law is then presented. The implementation of a differential Hebbian learning rule for a specific mean-frequency signal interpretation is shown to have a straightforward implementation using digital combinational logic with a variation of a previously developed programmable synapse circuit. This circuit is expected to be exploited for simple and straightforward implementation of future auto-adaptive neural circuits.

Watula, D.↗
NASA NTRS1993

Programmable display pushbuttons on the Space Station's telerobot control panel

The Man-Systems Telerobotics Laboratory at NASA's Johnson Space Center and supported by Lockheed, is working to ensure that the Flight Telerobotic Servicer (FTS) to be used on the Space Shuttle (Orbiter) and the Space Station has a well designed user interface from a Human Factors perspective. The FTS, which is a project led by NASA's Goddard Space Flight Center, will be a telerobot used for Space Station construction, maintenance, and satellite repair. It will be directly controlled from workstations on the Orbiter and the Space Station and monitored from a ground workstation. The FTS will eventually evolve into a more autonomous system, but in the short-term the system will be manually operated (teleoperated) for many tasks. This emphasizes the importance of the human/telerobot interface on this system. This phase of the FTS workstation evaluation covers a preliminary study of programmable display pushbuttons (PDP's). The PDP is constructed of a matrix of directly addressable electroluminescent (EL) pixels which can be used to form dot-matrix characters. PDP's can be used to display more than one message and to control more than one function. Since the PDP's have these features, then a single PDP may possibly replace the use of many single-function pushbuttons, rotary switches, and toggle switches, thus using less panel space. It is of interest to determine if PDP's can be used to adequately perform complex hierarchically structured task sequences. The objective of this investigation was to compare the performance of experienced and inexperienced Remote Manipulator System (RMS) operators while performing an RMS like task on simulated PDP and non-PDP computer prototypes so that guidelines governing the use of programmable display pushbuttons on the FTS workstation could be created. The functionality of the RMS on the Orbiter was used as a model for this evaluation since the functionality of the FTS at the time of this writing has not been solidified.

Stuart, Mark A.↗
NASA NTRS1996

Computer-Aided System Engineering and Analysis (CASE/A) Programmer's Manual, Version 5.0

The Computer Aided System Engineering and Analysis (CASE/A) Version 5.0 Programmer's Manual provides the programmer and user with information regarding the internal structure of the CASE/A 5.0 software system. CASE/A 5.0 is a trade study tool that provides modeling/simulation capabilities for analyzing environmental control and life support systems and active thermal control systems. CASE/A has been successfully used in studies such as the evaluation of carbon dioxide removal in the space station. CASE/A modeling provides a graphical and command-driven interface for the user. This interface allows the user to construct a model by placing equipment components in a graphical layout of the system hardware, then connect the components via flow streams and define their operating parameters. Once the equipment is placed, the simulation time and other control parameters can be set to run the simulation based on the model constructed. After completion of the simulation, graphical plots or text files can be obtained for evaluation of the simulation results over time. Additionally, users have the capability to control the simulation and extract information at various times in the simulation (e.g., control equipment operating parameters over the simulation time or extract plot data) by using "User Operations (OPS) Code." This OPS code is written in FORTRAN with a canned set of utility subroutines for performing common tasks. CASE/A version 5.0 software runs under the VAX VMS(Trademark) environment. It utilizes the Tektronics 4014(Trademark) graphics display system and the VTIOO(Trademark) text manipulation/display system.

Knox, J. C.↗