Search NASA⌕ Search

SEARCH · Search NASA

Results for “reaction sintering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

The Influence of Interstitial Ga and Interfacial Au (sub 2)P (sub 3) on the Electrical and Metallurgical Behavior of Au-Contacted III-V Semiconductors

The introduction of a very small amount of Ga into Au contact metallization on InP is shown to have a significant effect on both the metallurgical and electrical behavior of that contact system. Ga atoms in the interstices of the Au lattice are shown to be effective in preventing the solid state reactions that normally take place between Au and InP during contact sintering. In addition to suppressing the metallurgical interaction, the presence of small amounts of Ga is shown to cause an order of magnitude reduction in the specific contact resistivity. Evidence is presented that the reactions of GaP and GaAs with Au contacts are also drastically affected by the presence of Ga. The sintering behavior of the Au-GaP and the Au-GaAs systems (as contrasted with that of the Au-InP system) is explained as due to the presence of interstitial Ga in the contact metallization. Finally the large, two-to-three order of magnitude drop in the contact resistance that occurs in the Au-InP system upon sintering at 400 degrees Centigrade is shown to be a result of the formation of an Au (sub 2) P (sub 3) layer at the metal-semiconductor interface. Contact resistivities in the 10 (sup -6) ohm square centimeter range are obtained for as-deposited Au on InP when a thin (20 Angstrom) layer of Au (sub 2) P (sub 3) is introduced between the InP and the Au contacts.

Weizer, Victor G.↗
NASA NTRS1991

The influence of interstitial Ga and interfacial Au2P3 on the electrical and metallurgical behavior of Au-contacted III-V semiconductors

The effect of introducing a very small amount of Ga into Au-contacted InP on the behavior of that contact system was investigated. It was found that Ga affected both the metallurgical and the electrical behavior of the system. It is shown that Ga atoms in the interstices of the Au lattice prevent the solid-state reactions that normally take place between Au and InP during contact sintering and cause an order of magnitude reduction in the specific contact resistivity. It is also shown that the presence of Ga affects the reactions of GaP and GaAs with Au contacts.

Weizer, Victor G.↗
DOE OSTI2021

Identifying higher oxygenate synthesis sites in Cu catalysts promoted and stabilized by atomic layer deposited Fe 2 O 3

The conversion of syngas to higher oxygenates is an important step in the pathway towards the long-term sustainable production of fuels and chemicals. Mixed Cu/Fe catalysts combine metals with different CO activation characteristics, a property that makes them promising candidates for higher oxygenate production. However, Cu/Fe catalysts suffer from instability due to sintering and phase separation, and the active sites for higher oxygenate formation on these materials are not well understood. In this work, we use atomic layer deposition (ALD) to modify silica-supported Cu nanoparticles with monolayer precise amounts of Fe 2 O 3 and study the effects on catalyst structure, reactivity, and stability. We demonstrate that the Fe 2 O 3 ALD process is inherently selective towards deposition on the SiO 2 surface versus the Cu nanoparticles. As a result, a sufficiently thick Fe 2 O 3 layer surrounding the Cu nanoparticles acts as a barrier against Cu migration, preventing catalyst deactivation through sintering without covering the Cu. In syngas conversion reactions, we find that higher oxygenate selectivity increases with Fe 2 O 3 loading at low and intermediate ALD cycle numbers. Furthermore, using in situ X-ray absorption spectroscopy, we demonstrate that the Fe near the Cu nanoparticles is reduced to a metallic state under reaction conditions. From these measurements, we identify these metallic Cu/Fe interfaces as the active sites for higher oxygenate formation, which are most abundant at intermediate Fe 2 O 3 ALD cycle numbers. As the Fe 2 O 3 loading increases, higher oxygenate selectivity falls, resulting from encapsulation of the Cu nanoparticles by thick Fe 2 O 3 layers. Overall, the results demonstrate how thickness-controlled ALD Fe 2 O 3 can be used as both a promoter and stabilizer of Cu-based higher oxygenate synthesis catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

PUMA:POWDER UTILIZATION MODELING APPLICATION

SF-25-084 PUMA a high performance modeling framework to simulate powder processing. It provides a scalable tool for manufacturers to simulate powder pre- and post-processing. The tool can predict the distortion, residual stress, and (for reactive processes) reaction completion fraction of complex parts after curing/debinding, sintering, and infiltration processes. These predictions are key metrics industry uses to optimize these processes to produce dense, defect-free, stable components.

HU, TIANCHEN (GARY)↗
NASA NTRS1979

Combustion rig durability testing of turbine ceramics

A test facility for cyclic exposure of ceramic test bars to 1370 C has been designed as a means of the evaluation of the material durability under high-temperature cycling, particularly in heat-engine applications. The principal features of the test rig and test procedures are briefly discussed, and test results are presented for several commercial ceramics, including hot-pressed silicon nitride, carborundum sintered alpha-SiC, siliconized SiC, and reaction-bonded silicon nitride.

Carruthers, W. D.↗
NASA NTRS1991

Physical and chemical analysis of a Ni/H2 cell

A cycled aerospace nickel hydrogen (Ni/H2) cell was subjected to destructive physical analysis to determine the reason for a capacity loss after 5,967 cycles at 60 percent depth of discharge. The positive plates in the cell were analyzed in terms of chemical composition, active material utilization, charge efficiency, and thickness increase. The microstructure of a cross section of the positive plate was determined by backscattered electron image analysis. The results suggest that the capacity loss in the cell is caused by low charge acceptance and low active material utilization at the positive plate. The oxidized nickel species content of the positive plate increased due to corrosion of the nickel sintered skeleton. This appears to circumvent the orderly reaction of the active material. Microstructural analysis has indicated that a new phase of active material is formed with cycling.

H Vaidyanathan↗
NASA NTRS2017

Combustion Joining of Regolith Tiles for In-Situ Fabrication of Launch/Landing Pads on the Moon and Mars

To mitigate dust problems during launch/landing operations in lunar and Mars missions, it is desired to build solid pads on the surface. Recently, strong tiles have been fabricated from lunar regolith simulants using high-temperature sintering. The present work investigates combustion joining of these tiles through the use of exothermic intermetallic reactions. Specifically, nickel/aluminum (1:1 mole ratio) mixture was placed in a gap between the tiles sintered from JSC-1A lunar regolith simulant. Upon ignition by a laser, a self-sustained propagation of the combustion front over the mixture occurred. Joining was improved with increasing the tile thickness from 6.3 mm to 12.7 mm. The temperatures sufficient for melting the glass phase of JSC-1A were recorded for 12.7-mm tiles, which explains the observed better joining.

Ferguson, Robert E.↗
NASA NTRS2017

Combustion Joining of Regolith Tiles for In-Situ Fabrication of Launch/Landing Pads on the Moon and Mars

To mitigate dust problems during launch-landing operations in lunar and Mars missions, it is desired to build solid pads on the surface. Recently, strong tiles have been fabricated from lunar regolith simulants using high-temperature sintering. The present work investigates combustion joining of these tiles through the use of exothermic intermetallic reactions. Specifically, nickel aluminum (1:1 mole ratio) mixture was placed in a gap between the tiles sintered from JSC-1A lunar regolith simulant. Upon ignition by a laser, a self-sustained propagation of the combustion front over the mixture occurred. Joining was improved with increasing the tile thickness from 6.3 mm to 12.7 mm. The temperatures sufficient for melting the glass phase of JSC-1A were recorded for 12.7-mm tiles, which explains the observed better joining.

Ferguson, Robert E.↗
DOE OSTI2023

Strategies for regeneration of Pt-alloy catalysts supported on silica for propane dehydrogenation

Catalyst stability, resistance to deactivation, and regeneration remain a challenge for high temperature reaction processes. For Pt alloys used in propane dehydrogenation (PDH), the primary pathways of catalyst deactivation include coke formation and metal nanoparticle sintering over time. Recent work shows that silica-supported catalysts provide excellent selectivity for this reaction, but the regenerability of silica-supported catalysts has not been established. In this work, we study a series of Pt alloys, including PtMn, PtZn, and PtSn, for the PDH reaction at 550 °C and 600 °C, and we subject the catalysts to regeneration over multiple cycles. While oxidation in air restores the reactivity completely with minimal catalyst sintering, it is surprising to find that these catalysts can also be regenerated in pure hydrogen. Here we explore the types of coke formed on these catalysts using in situ temperature programmed oxidation (TPO). Two types of coke are found: one on the metallic NP surface, and a second on the silica support. Our work shows that treatment in hydrogen causes redistribution of the coke between the metal and support, which can restore most catalytic activity lost during a reaction run. Finally, periodic introduction of H 2 during a reaction cycle may constitute an unexplored strategy for extending the lifetime of PDH catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Fabrication and thermophysical properties of UO 2 -UB 2 and UO 2 -UB 4 composites sintered via spark plasma sintering

Uranium dioxide (UO 2 ) composites with uranium diboride (UB 2 ) and uranium tetraboride (UB 4 ) have been proposed as advanced fuel candidates due to their high thermal conductivity, high melting point, high fissile density and their ability to incorporate a built-in burnable poison by tailoring the targeted 10 B/ 11 B ratio. As such, it is important to assess the fabrication, and thermal and micromechanical properties of such composites. In this work, UO 2 -UB 2 and UO 2 -UB 4 samples with boride phase fractions of 5, 15 and 30 wt% were fabricated to high densities (above 95 % theoretical density) via spark plasma sintering (SPS). This enabled sintering at relatively low temperatures and short timescales. SPS also aided in maintaining the target phase fractions of the samples as reactions between the constituent phases were suppressed due to the short timescales and reducing environment during sintering. Here, thermal diffusivity measurements from 299 to 1273 K were conducted through laser flash analysis (LFA). The diffusivity increased as a function of boride weight fraction, and UB 2 additions increased the thermal diffusivity of the composites more than UB 4 additions. Assessment of the LFA results indicated in-situ reactions between the UO 2 and boride phases that suppress the thermal diffusivity occur above 800 K for all samples. Oxidation of the boride phase was proposed as the underlying reaction. This was supported by thermodynamic assessments from the literature, as well as microstructural, crystallographic, and nanoindentation characterization performed on these samples.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS2004

Sintering of BaCe(0.85)Y(0.15)O3-(Beta) With/Without SrTiO Dopant

The sintering behavior of BaCe(0.85)Y(0.15)O3-(Beta) doped with SrTiO is described. Complete reaction and crystallization of perovskite phase by solid state was achieved by calcining at 1200 degrees C for 24 hours.Smaples were sintered at 1450 degrees C, 1550 degrees C, and 1650 degrees C. SrTiOsub3 enhanced sintering, while optimal dopant level was different for powders synthesized by solid state and co-precipitation. Both powders exhibit similar grain growth behavior.

Dynys, Fred↗
NASA NTRS1985

Ceramic oxide reactions with V2O5 and SO3

Ceramic oxides are not inert in combustion environments, but can react with, inter alia, SO3, and Na2SO4 to yield low melting mixed sulfate eutectics, and with vanadium compounds to produce vanadates. Assuming ceramic degradation to become severe only when molten phases are generated in the surface salt (as found for metallic hot corrosion), the reactivity of ceramic oxides can be quantified by determining the SO3 partial pressure necessary for molten mixed sulfate formation with Na2SO3. Vanadium pentoxide is an acidic oxide that reacts with Na2O, SO3, and the different ceramic oxides in a series of Lux-Flood type of acid-base displacement reactions. To elucidate the various possible vanadium compound-ceramic oxide interactions, a study was made of the reactions of a matrix involving, on the one axis, ceramix oxides of increasing acidity, and on the other axis, vanadium compounds of increasing acidity. Resistance to vanadium compound reaction increased as the oxide acidity increased. Oxides more acidic than ZrO2 displaced V2O5. Examination of Y2O3- and CeO2-stabilized ZrO2 sintered ceramics which were degraded in 700 C NaVO3 has shown good agreement with the reactions predicted above, except that the CeO2-ZrO2 ceramic appears to be inexplicably degraded by NaVO3.

Jones, R. L.↗
DOE OSTI2026

Ultrafast Reactive Laser Sintering of Highly Conductive Garnet-Type LLZTO Solid Electrolytes

Rapid and scalable fabrication of garnet-type solid electrolytes remains a major challenge for the practical deployment of lithium metal batteries. Here, we report reactive laser sintering (RLS) as an ultrafast and potentially scalable strategy for fabricating garnet-type Li 6.4 La 3 Zr 1.4 Ta 0.6 O 12 (LLZTO) solid electrolytes. RLS of LLZTO enables simultaneous reaction and densification, achieving ∼95% relative density while minimizing lithium loss and suppressing secondary phase formation. Compared to conventional furnace sintering, RLS promotes enhanced grain growth and improved densification, leading to improved ionic conductivity (0.36 ± 0.08 mS cm −1 ) while maintaining comparable activation energies for Li + transport. Structural characterization by X-ray diffraction (XRD), Raman spectroscopy, and solid-state 6 Li/ 7 Li NMR confirms the formation of cubic garnet LLZTO with homogeneous microscale elemental distribution. In addition, nanoindentation measurements demonstrate that RLS preserves the mechanical properties of the garnet framework despite ultrafast localized thermal processing. By integrating simultaneous reaction and densification with tunable microstructural control, reactive laser sintering provides a promising manufacturing pathway for high-performance garnet solid electrolytes toward next-generation solid-state batteries.

CO2 laser↗
DOE OSTI2022

Interpreting the Operando X-ray Absorption Near-Edge Structure of Supported Cu and CuPd Clusters in Conditions of Oxidative Dehydrogenation of Propane: Dynamic Changes in Composition and Size

Supported subnano-cluster catalysts are highly dynamic, developing true active sites only under the pressures and temperatures of reaction conditions. Operando X-ray absorption near-edge structure (XANES) spectroscopy can track changes in the oxidation state and the local environment of cluster atoms, providing insight into the development of these active sites. While bulk metal, oxide, and hydroxide standards are often used for fitting experimental XANES spectra to obtain average oxidation states, we recently showed that computed cluster standards of relevant compositions are a more suitable basis, producing more accurate fits. Here, we theoretically interpret the operando XANES of supported Cu 3 Pd and Cu 4 clusters during temperature-programmed reaction (TPRx) of oxidative dehydrogenation of propane. We use an expanded basis set including both globally optimized computed clusters and bulk standards. Not only can we track reversible composition/oxidation state change with temperature, but also the irreversible growth of the bulk fraction upon heating, which we attribute to cluster sintering. This has important implications for the mechanism of the catalyzed reaction and the nature of the available active sites. Here, we propose that operando XANES provides most significant insight into the nature of supported cluster catalysts in reaction conditions when interpreted using mixed computed cluster and bulk standards.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Electrocatalyst comprising a crumpled transition metal dichalcogenide support loaded with monodispersed metal nanoparticles

An electrocatalyst comprises a crumpled transition metal dichalcogenide support loaded with catalytic metal nanoparticles through spontaneous reduction reactions. The support can be prepared by hydrothermal conversion of 2D nanosheets to 3D hierarchically crumpled sheets. As an example, using crumpled MoS 2 as a support, highly tunable Ru loadings were obtained using the electrostatic interaction between MoS 2 and RuCl 3 in solution. Control over Ru loading was leveraged to produce Ru—MoS 2 electrocatalysts that demonstrate different nitrogen reduction reaction activities, and which show varying resistance to electrochemical sintering and deactivation. Further, these high surface area materials can be utilized for many applications, including electrocatalysts, supercapacitors, and batteries.

Percival, Stephen↗
DOE OSTI2021

Large-scale dissolution of sintered Mo disks

Non-uranium production of 99 Mo via neutron capture or by photonuclear reaction using an electron accelerator is receiving considerable attention. For commercial production of 99 Mo, post-irradiation processes must incorporate a robust design for easy scale-up. Once developed, large-scale chemical processes must be optimized for hot-cell operations and potential automation. In this work, we present experimental results on the large-scale dissolution of sintered Mo disks using three 50% hydrogen peroxides from different suppliers. Dissolution rates obtained for 600-g Mo batches and potential reasons for different dissolution behaviors is discussed.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2021

Molybdenum Recovery from Filters Used in Large-scale Dissolution of Sintered Mo-disks

99 Mo production with linear accelerators can be achieved via the bremsstrahlung photonuclear reaction 100 Mo(γ,n) 99 Mo or the neutron capture reaction 98 Mo(n,γ) 99 Mo. For commercial producers, maximum recovery of enriched 98 Mo and 100 Mo target material is critical for sustaining an economic production cycle. During the peroxide dissolution of Mo metal disks and subsequent conversion to K 2 MoO 4 , several grams of Mo can be lost during filtration from solution when several hundred grams of sintered Mo disks are processed. This investigation shows that 5–8 g Mo is routinely retained on the filter units, but it can be almost fully recovered using aqueous washes. Washing can be done immediately and incorporated into the dissolution procedure, or it can occur several months after the initial filtration process to decrease processing time.

07 ISOTOPE AND RADIATION SOURCES↗