Search NASA⌕ Search

SEARCH · Search NASA

Results for “reverse bias”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Degradation behavior of CIGS solar Cells: A parametric analysis

A parametric study of the effect of bulk and interface properties on device characteristics as a function of heat and light stress under open-circuit and short-circuit conditions is developed for Cu(In,Ga)(S,Se) 2 solar cells using SCAPS-1D simulator. The variables and interdependencies modeled include: (1) conduction band offset (CBO) between buffer and absorber; (2) buffer ionized donor density; (3) CIGS shallow acceptor density; (4) CIGS deep acceptor density; (5) CIGS shallow donor density; (6) ionized acceptor concentration in the ordered vacancy compound (OVC) CIGS/buffer interface; and (7) back contact work-function. An increase in absorber shallow acceptor or a decrease in shallow donor density results in an increase in net carrier density and open-circuit voltage (V OC ). Further, a decrease in V OC is observed with an increase in the deep acceptors or neutral midgap defects in the CIGS due to higher charge carrier recombination. A change of CBO from spike to cliff condition is a dominant mechanism of decreasing VOC with an interface defect density of 10 12 cm -2 . The minimum depletion width is found to be specifically sensitive to CBO and interface defect density. An inflection in the capacitance–voltage curves (in reverse bias) is observed with simultaneous increase in bulk deep acceptor density and shallow donor density near the back contact.

14 SOLAR ENERGY↗
DOE OSTI2026

Measuring pH Changes Inside a Bipolar Membrane Junction

Here, the local pH environment within bipolar membrane (BPM) junctions is complex and not well understood, yet it is important to control for advancing the performance of BPM-based electrochemical systems. We report a voltammetric strategy using an ultrathin Ni mesh pH probe to spatially resolve pH changes in the BPM junction during model BPM electrolyzer operation. Under reverse bias, we observe depletion of OH – at the anion-exchange layer (AEL) interface, with a degree diminishing with increasing distance from the AEL. These gradients correlate with current-dependent water dissociation (WD) and are modulated by the electric field and the surface charge state of the catalyst. By correlating spatial pH profiles with the surface-charging behavior of WD catalysts, we explore a mechanism of catalyst-mediated H + and OH – transfer facilitated by hydrogen-bonding networks. These findings highlight the role of local chemistry and electrostatics in BPM performance and offer new methods to probe and engineer catalytic junctions in electrochemical energy devices.

Hou, Shujin [University of California, Berkeley, C↗
DOE OSTI2026

How Does Water Dissociation Work in Bipolar Membranes?

Bipolar membranes (BPMs) create counteracting spatial gradients of pH and electrostatic potential in electrochemical systems, enabling applications in pH regulation, electrocatalysis, and separations. At the polarized junction of a BPM the water dissociation (WD, 2H2O ⇌ H3O+ + OH-) reaction can be driven, but it remains poorly understood. In this Perspective, we integrate molecular insights from bulk-water autoionization and the associated field effects with continuum descriptions of BPM electrostatics and experimental WD kinetic analyses to describe possible mechanisms of voltage-driven WD. Pristine BPM junctions highlight both the limits of primarily electric-field-driven WD and the practical challenges of junction stability at extreme reverse bias. Introducing heterogeneous catalyst layers, commonly metal oxides and graphene oxides, accelerates WD by orders of magnitude through hypothesized coupled effects in which surface acid-base functionality and high-density hydroxyl sites mediate proton-transfer steps, and catalyst mobile electronic/ionic charges redistribute the junction electric potential drop to shape the local electric fields and reactive microenvironments. Kinetic analyses suggest two regimes of heterogeneous WD mechanism, including field-driven ordering of interfacial water and a Second-Wien-Effect dissociation-barrier lowering. We conclude by defining the key unknown variables (local pH, electrostatic potential, catalyst charge state and relationships among mechanisms) and outlining experimental and multiscale modeling strategies needed for predictive WD catalysis and for controlling related ion-transfer reactions.

Wu, Yifan↗
DOE OSTI2024

A thermotropic liquid crystal enables efficient and stable perovskite solar modules

Perovskite solar cells have seen impressive progress in performance and stability, yet maintaining efficiency while scaling area remains a challenge. Here we find that additives commonly used to passivate large-area perovskite films often co-precipitate during perovskite crystallization and aggregate at interfaces, contributing to defects and to spatial inhomogeneity. Here we develop design criteria for additives to prevent their evaporative precipitation and enable uniform passivation of defects. We explored liquid crystals with melting point below the perovskite processing temperature, functionalization for defect passivation and hydrophobicity to improve device stability. We find that thermotropic liquid crystals such as 3,4,5-trifluoro-4'-(trans-4-propylcyclohexyl)biphenyl enable large-area perovskite films that are uniform, low in defects and stable against environmental stress factors. We demonstrate modules with a certified stabilized efficiency of 21.1% at an aperture area of 31 cm 2 and enhanced stability under damp-heat conditions (ISOS-D-3, 85% relative humidity, 85 °C) with T 86 (the duration for the efficiency to decay to 86% of the initial value) of 1,200 h, and reverse bias with (ISOS-V-1, negative maximum-power-point voltage) and without bypass diodes.

14 SOLAR ENERGY↗
DOE OSTI2026

Challenges, Technological Pathways and Trade-Offs of Perovskite Solar Modules for Long-Term Operation

Perovskite solar modules (PSMs) have emerged as a promising photovoltaic technology due to their high efficiency, low fabrication cost and compatibility with lightweight and flexible applications. However, ensuring long-term reliable performance under real-world conditions remains a critical barrier to commercialization. PSMs degrade through mechanisms that differ substantially from those affecting established technologies such as silicon, particularly under environmental stressors like ultraviolet light, oxygen, temperature cycling and reverse bias. Here we provide an analysis of the degradation pathways specific to perovskite modules and discuss why standard accelerated tests often fail to predict outdoor performance. We conceptualize challenges across material, device and module levels and evaluate strategies to mitigate ion migration, interfacial breakdown and encapsulation failure. By highlighting the need for realistic testing protocols and durable materials, we propose a framework highlighting key challenges, technological pathways and the trade-offs required to extend perovskite module lifetimes towards long-term operation, aiming to guide the development of PSMs capable of a 30-year operational lifetime.

14 SOLAR ENERGY↗
DOE OSTI2022

Design and optimization of high temperature optocouplers as galvanic isolation

The commercial InGaN-based (blue and green) and AlGaInP-based (red) multiple quantum well (MQW) lighting emitting diodes (LEDs) were studied in a wide range of temperatures up to 800 K for their light emission and detection (i.e., LEDs operated under reverse bias as photodiodes (PDs)) characteristics. The results indicate the feasibility of integrating a pair of selected LEDs to fabricate high temperature (HT) optocouplers, which can be utilized as galvanic isolation to replace the bulky isolation transforms in the high-density power modules. A detailed study on LEDs and PDs were performed. The external quantum efficiency (EQE) of the LED and PDs were calculated. Higher relative external quantum efficiency (EQE) and lower efficiency droops with temperatures are obtained from the blue and green LEDs for display compared with the blue one for lighting and red LED for display. The blue for lighting and red for display devices show superior responsivity, specific detectivity (D*), and EQE compared with blue and green for display when operated as PDs. The results suggest that red LED devices for display can be used to optimize HT optocouplers due to the highest wavelength overlapping compared with others.

42 ENGINEERING↗
DOE OSTI2026

Nanopores with dynamic pore opening diameter

Solid state nanopores have emerged as model systems for understanding transport properties on the nanoscale. They serve as templates for both preparing mimics of biological channels and designing biological sensors. Unlike their biological inspirations, the majority of nanopores prepared thus far, however, have been structurally static devices such that the pore opening diameter is fixed. If we could prepare nanopores whose opening diameter fluctuated in time with controlled amplitude at known locations in the pore, we could create ionic memristors as well as achieve new transport modes. Here we present ∼10 nm diameter single nanopores drilled through a 10 nm thick gold layer positioned on top of a 30 nm thick silicon nitride film. Two types of devices were prepared; one containing single stranded DNA and the other containing hairpin DNA attached to the discrete layer of gold using thiol chemistry. When an external electric field was applied across a nanopore with single stranded DNA, the nanoconfined DNA molecules exhibited steric and electrical constraints that led to memristor-like behavior in the current–voltage curves. The degree of hysteresis was controlled by salt concentration, magnitude of voltage and pore diameter. In contrast, nanopores containing DNA hairpins conducted similar currents in forward and reverse bias in agreement with the rigidity of the hairpin molecule. The experiments are explained by Brownian dynamics simulations that reveal voltage and salt concentration induced changes in DNA extension. The degree of DNA extension was also found to be dependent on the location of the molecules along the pore axis. The nanopores presented here provide the first steps towards preparation of non-equilibrium nanopore systems.

Vlassiouk, Ivan [ORNL] (ORCID:0000000254940386)↗
DOE OSTI2020

Local electric field measurement in GaN diodes by exciton Franz–Keldysh photocurrent spectroscopy

The eXciton Franz–Keldysh (XFK) effect is observed in GaN p–n junction diodes via the spectral variation of photocurrent responsivity data that redshift and broaden with increasing reverse bias. Photocurrent spectra are quantitatively fit over a broad photon energy range to an XFK model using only a single fit parameter that determines the line shape and the local bias (V l ), uniquely determining the local electric field maximum and depletion widths. As expected, the spectrally determined values of V l vary linearly with the applied bias (V) and reveal a large reduction in the local electric field due to electrostatic non-uniformity. The built-in bias (V bi ) is estimated by extrapolating V l at V=0, which, when compared with independent C-V measurements, indicates an overall ±0.31 V accuracy of V l . This demonstrates sub-bandgap photocurrent spectroscopy as a local probe of electric field in wide bandgap diodes that can be used to map out regions of device breakdown (hot spots) for improving electrostatic design of high-voltage devices.

42 ENGINEERING↗
DOE OSTI2021

Defect characterization and charge transport measurements in high-resolution Ni/n-4H-SiC Schottky barrier radiation detectors fabricated on 250 μ m epitaxial layers

Advances in the growth processes of 4H-SiC epitaxial layers have led to the continued expansion of epilayer thickness, allowing for the detection of more penetrative radioactive particles. In this work, we report the fabrication and characterization of high-resolution Schottky barrier radiation detectors on 250 μm thick n-type 4H-SiC epitaxial layers, the highest reported thickness to date. Several 8 × 8 mm 2 detectors were fabricated from a diced 100 mm diameter 4H-SiC epitaxial wafer grown on a conductive 4H-SiC substrate with a mean micropipe density of 0.11 cm -2 From the Mott–Schottky plots, the effective doping concentration was found to be in the range (0.95–1.85) × 10 14 cm -3 , implying that full depletion could be achieved at ~5.7 kV (0.5 MV/cm at the interface). The current-voltage characteristics demonstrated consistently low leakage current densities of 1–3 nA/cm 2 at a reverse bias of -800 V. This resulted in the pulse-height spectra generated using a 241Am alpha source (5486 keV) manifesting an energy resolution of less than 0.5% full width at half maximum (FWHM) for all the detectors at -200 V. The charge collection efficiencies (CCEs) were measured to be 98–99% with no discernable correlation to the energy resolution. A drift-diffusion model fit to the variation of CCE as a function of bias voltage, revealed a minority carrier diffusion length of ~10 μm. Deep level transient spectroscopy measurements on the best resolution detector revealed that the excellent performance was the result of having ultralow concentrations of the order of 1011 cm-3 lifetime limiting defects—Z 1/2 and EH 6/7 .

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2022

Influence of Heat Treatments in H 2 and Ar on the E 1 center in β -Gs 2 O 3

In this report the influence of heat treating n-type bulk β-Ga 2 O 3 in hydrogen (H2) and argon (Ar) gases on the presence of the defect level commonly labeled as E 1 was studied. Fourier transform-infrared spectroscopy confirms that hydrogen (H) is incorporated into β-Ga 2 O 3 during H 2 annealing at 900 °C. Deep-level transient spectroscopy measurements reveal that the concentration of the E 1 level is promoted by the introduction of H, in contrast to what is observed in samples heat-treated in an Ar flow. We further find the E 1 level to be stable against heat treatments at 650 K, both with and without an applied reverse-bias voltage. Potential candidates for the defect origin of E 1 are investigated using hybrid-functional calculations, and three types of defect complexes involving H are found to exhibit charge-state transition levels compatible with E 1 , including substitutional H at one of the threefold coordinated O sites, Ga-substitutional shallow donor impurities passivated by H, and certain configurations of singly hydrogenated Ga–O divacancies. Among these types, only the latter exhibit H binding energies that are consistent with the observed thermal stability of E 1 .

36 MATERIALS SCIENCE↗
DOE OSTI2022

Preliminary benchmarks and analysis of boundary conditions in a trenched microstructured silicon radiation detector

Microstructured neutron detectors have the benefit of enhanced neutron detection efficiency as compared to planar devices, achieved by etching 6 LiF-filled trenches on the top surface of a silicon PIN diode. This sensor geometry results in a complex electric field distribution and depletion characteristics within the diode under reverse bias. For the first time on record, the effects of a fixed oxide charge on the microstructured device depletion characteristics and mobile carrier transport is investigated. Prototype detectors were fabricated with non-conformal surface doping. Capacitance voltage and current voltage measurements were performed for these prototypes and compared with COMSOL Multiphysics simulations. A spectral response from an 241Am alpha particle source was acquired and analyzed. It was found that monoenergetic alpha particles produce three prominent peaks in the pulse height spectrum output by the device. The peaks were confirmed by simulations to correlate with dead layers and incident trajectories into the microstructure. It was also found that significant differences in pulse rise time result, corresponding with events arriving in a low-field region in the fins and a high-field region in the bulk. Geant4 was utilized for radiation transport, interaction modeling, and benchmarking the spectral data. The results of this simulation work provide confidence in the ability to attain and benchmark electrical characteristics and spectral data for semiconductor radiation detectors employing complex microstructures.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2022

Low voltage AC electroluminescence in silicon MOS capacitors

Low power silicon based light source and detector are attractive for on-chip photonic circuits given their ease of process integration. However, conventional silicon light emitting diodes emit photons with energies near the band edge where the corresponding silicon photodetectors lack responsivity. On the other hand, previously reported hot carrier electroluminescent silicon devices utilizing a reverse biased diode require high operating voltages. Here, we investigate hot carrier electroluminescence in silicon metal–oxide–semiconductor capacitors operating under transient voltage conditions. Further, during each voltage transient, large energy band bending is created at the edge of the source contact, much larger than what is achievable at a steady state. As a result, electrons and holes are injected efficiently from a single source contact into the silicon channel at the corresponding voltage transient, where they subsequently undergo impact ionization and phonon-assisted interband recombination. Notably, we show low voltage operation down to 2.8 V by using a 20 nm thick high-κ gate dielectric. We show further voltage scaling is possible by reducing the gate dielectric thickness, thus presenting a low voltage platform for silicon optoelectronic integrated circuits.

42 ENGINEERING↗
DOE OSTI2023

7.86 kV GaN-on-GaN PN power diode with BaTiO3 for electrical field management

Devices based on gallium nitride (GaN) have great potential for high power switching applications due to the high breakdown field and high electron mobility. In this work, we present a vertical GaN-on-GaN PN power diode using high dielectric constant material, BaTiO3, for electrical field management and high breakdown voltages, in together with an optimized guard-ring and field plate design. Numerical simulation shows that with high-k dielectrics implemented, the peak electrical field at the PN interface is mitigated from 3.5 to 3.1 MV/cm under a reverse bias of −9.05 kV. The device design with BaTiO3 shows a breakdown voltage of 9.65 kV or about 600 V improvement. The fabricated diodes with a 57 μm thick drift layer demonstrate a breakdown voltage of 7.86 kV on a bulk GaN substrate. The device has an on-resistance of 2.8 mΩ cm2 and a Baliga figure of merit of 22 GW/cm2.

Physics↗
DOE OSTI2024

Breakdown characteristics analysis of kV-class vertical GaN PIN rectifiers by wafer-level sub-bandgap photoluminescence mapping

This work reports analysis of the reverse-bias breakdown characteristics of homojunction gallium nitride (GaN) p–i–n (PIN) rectifiers fabricated on bulk GaN substrates. Sub-bandgap photoluminescence mapping at room temperature as a contactless, non-destructive wafer inspection method was performed to analyze the impact of material properties on grown GaN PIN diodes and to study the correlation between defect types and breakdown characteristics of vertical GaN PIN rectifiers. Under the sub-bandgap excitation, yellow luminescence is dominant. The premature breakdown characteristics of the fabricated kV-class vertical GaN PIN rectifiers with nitrogen-implanted floating guard rings are found to be associated with material defects and deep level complexes. Photoluminescence mapping has demonstrated its effectiveness in quantitative analysis of dislocations and other types of defects.

42 ENGINEERING↗
DOE OSTI2026

Electric field dependence of nanoscale cathodoluminescence inside Cr doped β-Ga 2 O 3 interfaces

Chromium (Cr) is a common impurity in β-Ga 2 O 3 crystals, where its characteristic R1 and R2 luminescence lines are susceptible to both the host crystal field and externally applied fields. Here, in this work, we demonstrate that the Cr cathodoluminescence (CL) quenches toward the bulk of the crystal but enhances with applied reverse bias, reflecting the effect of free carrier depletion with increasing electric field. Furthermore, we illustrate that the R1/R2 CL intensity ratio, measured as the integrated area ratio of R1 to R2, can be used as a direct probe of the electric field in a Ni-β-Ga 2 O 3 : Cr Schottky diode. This optical calibration method provides a complementary approach to conventional C–V and I–V measurements for determining electric field strength in the depletion region of β-Ga 2 O 3 -based Schottky diodes and can be extended to other semiconductors and multilayer device structures.

36 MATERIALS SCIENCE↗
DOE OSTI2026

AlGaN/GaN Core-Shell Nanofin Diodes on Si Substrates for Vertical GaN Electronics

We demonstrate plasma-assisted MBE selective-area growth of GaN/AlGaN core-shell structures on Si(111) as a path to vertical GaN devices. The selective-area growth enables the full vertical and uniform core-shell fin structures to be realized in a continuous growth without breaking vacuum. TEM images and EDS mapping of the core-shell structures show well-aligned crystal structure and sharp heterointerfaces. Dislocation filtering was observed in STEM imaging of the fin structure. P-N junction diodes fabricated with GaN/AlGaN core-shell structures reveal ideality factors as low as 1.5, and the reverse-bias leakage is consistent with trap-assisted space-charge-limited conduction. While practical challenges exist, including material-related leakage, growth-related challenges and optimization, this demonstration of p-n junction by this method may provide a path to vertical Superjunction device concepts in GaN and related materials.

Xiong, Juncheng [University of Notre Dame, IN (Uni↗
DOE OSTI2021

Picosecond Timing Resolution Measurements of Low Gain Avalanche Detectors with a 120 GeV Proton Beam for the TOPSiDE Detector Concept

This paper presents results that take a critical step toward proving 10 ps timing resolution’s feasibility for particle identification in the TOPSiDE detector concept for the Electron-Ion Collider. Measurements of LGADs with a thickness of 35 μm and 50 μm are evaluated with a 120 GeV proton beam. The performance of the gain and timing response is assessed, including the dependence on the reverse bias voltage and operating temperature. The best timing resolution of UFSDs in a test beam to date is achieved using three combined planes of 35 μm thick LGADs at -30°C with a precision of 14.3 ± 1.5 ps.

Particle tracking detectors↗
DOE OSTI2023

1.2-kV Vertical GaN PIN Rectifier With Ion-Implanted Floating Guard Rings

Here, this work reports on the fabrication and properties of a homojunction gallium nitride (GaN) p-i-n (PIN) rectifier fabricated on a free-standing GaN substrate. Uniform device performance is achieved with breakdown voltage (BV) >1.2 kV and low ON-resistance × area ( R ON A ). The statistics of the BV measurements show 58.5% of devices achieve BV >1.3 kV, and 71.1% of devices achieve BV >1.2 kV, as attributed to high quality and control in both epitaxial growth and device process. At room temperature, R ON A is 0.23 mΩ∙ cm 2 at a current density ( J ) of 6.9 kA/cm2. The corresponding Baliga’s figure of merit is >5.97 GW/cm 2 . Temperature-dependent reverse I – V measurements were performed and show a positive temperature coefficient of 0.42 V/K, indicating the avalanche capability of reverse breakdown. Further analysis with the Poole-Frenkel model on the temperature-dependent measurement suggested that a trap-assisted tunneling process contributed to the reverse leakage current. Floating guard rings (FGRs) formed by nitrogen implantation serve as an effective edge termination technique in these GaN PIN rectifiers, resulting in uniform performance in both forward and reverse bias.

42 ENGINEERING↗