Search NASA⌕ Search

SEARCH · Search NASA

Results for “rods”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Testing of improved polyimide actuator rod seals at high temperature and under vacuum conditions for use in advanced aircraft hydraulic systems

Polyimide second-stage rod seals were evaluated to determine their suitability for applications in space station environments. The 6.35-cm (2.5-in.)K-section seal was verified for thermal cycling operation between room temperature and 478 K (400 F) and for operation in a 133 micron PA(0.000001 mm Hg) vacuum environment. The test seal completed the scheduled 96 thermal cycles and 1438 hr in vacuum with external rod seal leakage well within the maximum allowable of two drops per 25 actuation cycles. At program completion, the seals showed no signs of structural degradation. Posttest inspection showed the seals retained a snug fit against the shaft and housing walls, indicating additional wear life capability. Evaluation of a molecular flow section during vacuum testing, to inhibit fluid loss through vaporization, showed it to be beneficial with MIL-H-5606, a petroleum-base fluid, in comparison with MIL-H-83282, a synthetic hydrocarbon-base fluid.

Sellereite, B. K.↗
NASA NTRS1975

Effect of rod gap spacing on a suction panel for laminar flow and noise control in supersonic wind tunnels

Results are presented of a coordinated experimental and theoretical study of a sound shield concept which aims to provide a means of noise reduction in the test section of supersonic wind tunnels at high Reynolds numbers. The model used consists of a planar array of circular rods aligned with the flow, with adjustable gaps between them for boundary layer removal by suction, i.e., laminar flow control. One of the basic requirements of the present sound shield concept is to achieve sonic cross flow through the gaps in order to prevent lee-side flow disturbances from penetrating back into the shielded region. Tests were conducted at Mach 6 over a local unit Reynolds number range from about 1.2 x 10 to the 6th power to 13.5 x 10 to the 6th power per foot. Measurements of heat transfer, static pressure, and sound levels were made to establish the transition characteristics of the boundary layer on the rod array and the sound shielding effectiveness.

Harvey, W. D.↗
NASA NTRS1975

Properties of axial or torsional free-vibration frequency of rods

The investigation reported shows that for a clamped rod with an odd number of degrees of freedom, the middle frequency is independent of any nonuniformity in the area distribution. The frequencies in the lower half of the spectrum of a rod are found to be conjugate to the frequencies in the upper half. In the case of a design modification which leaves a certain frequency in the lower half spectrum unchanged, the conjugate frequency in the upper half will also remain unchanged.

Segenreich, S. A.↗
NASA NTRS1981

Measurement of oil film thickness for application to elastomeric Stirling engine rod seals

The rod seal in the Stirling engine has the function of separating high pressure gas from low or ambient pressure oil. An experimental apparatus was designed to measure the oil film thickness distribution for an elastomeric seal in a reciprocating application. Tests were conducted on commercial elastomeric seals having a 76 mm rod and a 3.8 mm axial width. Test conditions included 70 and 90 seal durometers, a sliding velocity of 0.8 m/sec, and a zero pressure gradient across the seal. An acrylic cylinder and a typical synthetic base automotive lubricant were used. The experimental results showed that the effect of seal hardness on the oil film thickness is considerable. A comparison between analytical and experimental oil film profiles for an elastomeric seal during relatively high speed reciprocating motion showed an overall qualitative agreement.

Krauter, A. I.↗
NASA NTRS1982

Compliance calibration of the short rod chevron-notch specimen for fracture toughness testing of brittle materials

The short rod chevron-notch specimen has the advantages of (1) crack development at the chevron tip during the early stage of test loading, and (2) convenient calculation of plane-strain fracture toughness from the maximum test load and from a calibration factor which depends only on the specimen geometry and manner of loading. For generalized application, calibration of the specimen over a range of specimen proportions and chevron-notch configurations is necessary. Such was the objective of this investigation, wherein calibration of the short rod specimen was made by means of experimental compliance measurements converted into dimensionless stress intensity factor coefficients.

Bubsey, R. T.↗
NASA NTRS1983

Wind tunnel noise reduction at Mach 5 with a rod-wall sound shield

A method of shielding a wind-tunnel model from noise radiated by the tunnel-wall boundary layer has been developed and tested at the Langley Research Center. The shield consists of a rectangular array of longitudinal rods with boundary-layer suction through gaps between the rods. Tests were conducted at Mach 5 over a unit Reynolds number range of 1.0-3.5 x 10 to the 7th/m. Hot-wire measurements indicated the freestream noise, expressed in terms of the rms pressure fluctuations normalized by the mean pressure, was reduced from about 1.4 percent just upstream of the shielded region of a minimum level of about 0.4 percent in the forward portion of the shielded flow.

Creel, T. R.↗
NASA NTRS1986

Composite Lightning Rods for Aircraft

Composite, lightweight sacrificial tip with graphite designed reduces lightning-strike damage to composite parts of aircraft and dissipates harmful electrical energy. Device consists of slender composite rod fabricated from highly-conductive unidirectional reinforcing fibers in matrix material. Rods strategically installed in trailing edges of aircraft wings, tails, winglets, control surfaces, and rearward-most portion of aft fuselage.

Bryan, Charles F., Jr.↗
NASA NTRS1987

One-dimensional wave propagation in rods of variable cross section: A WKBJ solution

As an important step in the characterization of a particular dynamic surface displacement transducer (IQI Model 501), a one-dimensional wave propagation in isotropic nonpiezoelectric and piezoelectric rods of variable cross section are presented. With the use of the Wentzel-Kramers-Brillouin-Jeffreys (WKBJ) approximate solution technique, an approximate formula, which relates the ratio of the amplitudes of a propagating wave observed at any two locations along the rod to the ratio of the cross sectional radii at these respective locations, is derived. The domains of frequency for which the approximate solution is valid are discussed for piezoelectric and nonpiezoelectric materials.

Ochi, Simeon C. U.↗
NASA NTRS1989

Energy distributions in rods and beams

A hypothesis proposed by Nefske and Sung (1987) that the mechanical energy flow in acoustic/structural systems can be modeled using a thermal energy flow analogy was tested for both longitudinal vibration in rods and transverse flexural vibrations in beams. It was found that the rod behaves according to the energy flow analogy. However, the beam solutions behaved significantly differently than predicted by the thermal analogy, unless spatially averaged energy and power flow were considered. Otherwise, the beam analysis is restricted to frequencies where the near-field terms in the displacement solution are negligible over most of the beam.

Wohlever, J. C.↗
NASA NTRS1989

Approximation in LQG control of a thermoelastic rod

Control and estimator gains are computed for linear-quadratic-Gaussian (LQG) optimal control of the axial vibrations of a thermoelastic rod. The computations are based on a modal approximation of the partial differential equations representing the rod, and convergence of the approximations to control and estimator gains is the main issue.

Gibson, J. S.↗
NASA NTRS1991

Computing Temperatures In Optically Pumped Laser Rods

Computer program presents new model solving temperature-distribution problem for laser rods of finite length and calculates both radial and axial components of temperature distributions in these rods. Contains several self-checking schemes to prevent over-writing of memory blocks and to provide simple tracing of information in case of trouble. Written in Microsoft FORTRAN 77.

Farrukh, Usamah O.↗
NASA NTRS1991

Mathematical models for determining the protected spaces of the vertical lightning rod

Two mathematical models are presented for determining the protected spaces of the vertical lightning-rod. In the first model there was applied the circular approximation. Through the introduction of the modified striking distance in the second improved approximation there was obtained a new model for the protected space of the lightning-rod. The models are of general type, foreseen for the three-dimensional space and they are simply applied on solving the practical problems.

Mladenovic, I.↗
NASA NTRS1991

A survey of laser lightning rod techniques

The work done to create a laser lightning rod (LLR) is discussed. Some ongoing research which has the potential for achieving an operational laser lightning rod for use in the protection of missile launch sites, launch vehicles, and other property is discussed. Because of the ease with which a laser beam can be steered into any cloud overhead, an LLR could be used to ascertain if there exists enough charge in the clouds to discharge to the ground as triggered lightning. This leads to the possibility of using LLRs to test clouds prior to launching missiles through the clouds or prior to flying aircraft through the clouds. LLRs could also be used to probe and discharge clouds before or during any hazardous ground operations. Thus, an operational LLR may be able to both detect such sub-critical electrical fields and effectively neutralize them.

Barnes, Arnold A., Jr.↗
NASA NTRS1991

High current pulse testing for ground rod integrity

A test technique was developed to assess various grounding system concepts used for mobile facilities. The test technique involves applying a high current pulse to the grounding system with the proper waveshape and magnitude to simulate a lightning return stroke. Of concern were the step voltages present along the ground near the point of lightning strike. Step voltage is equated to how fast the current pulse is dissipated by the grounding system. The applied current pulse was produced by a high current capacitor bank with a total energy content of 80 kilojoules. A series of pulse tests were performed on two types of mobile facility grounding systems. One system consisted of an array of four 10 foot copper clad steel ground rods connected by 1/0 gauge wire. The other system was an array of 10 inch long tapered ground rods, strung on stainless steel cable. The focus here is on the pulse test technique used and its relevance to actual lightning strike conditions.

Walko, Lawrence C.↗
NASA NTRS1991

Scalable diode array pumped Nd rod laser

Experiments were carried out on a five-array pump head which utilizes gold-coated reflective cones to couple the pump energy to Nd:YAG and Nd:YLF rod lasers, demonstrating high efficiency and uniform energy deposition. Because the cones function as optical diodes to light outside their acceptance angle (typically 10-15 deg), much of the diode energy not absorbed on the first pass can be returned to the rod.

Zenzie, H. H.↗
NASA NTRS1992

Making Crystal Filaments From Extruded Ceramic Rods

New process produces single-crystal fibers of ceramic or metal at lower cost. Single-crystal filament drawn from tip of extruded polycrystalline rod. Extrusion produces longer rods from which longer fibers drawn. Potentially feeds single fiber drawing process directly. Continuous filaments made, and material not subjected to contamination from storage and transfer to drawing machine. Filaments used as reinforcing fibers in composite materials.

Westfall, Leonard J.↗
NASA NTRS1993

Three-Rod Linear Ion Traps

Three-parallel-rod electrode structures proposed for use in linear ion traps and possibly for electrostatic levitation of macroscopic particles. Provides wider viewing angle because they confine ions in regions outside rod-electrode structures.

Janik, Gary R.↗