Search NASA⌕ Search

SEARCH · Search NASA

Results for “rotor design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Design of a 3.4-MW wind turbine with integrated plasma actuator-based load control

Historically, cost reduction in wind energy has been accomplished by increasing hub heights and rotor diameters to capture more energy per turbine. The growth in rotor and turbine costs with increasing turbine sizes is also driven by the additional structure that must be added to withstand unsteady aerodynamic loads caused by turbulence, gusts, wind shear, misaligned yaw, upwind wakes, and the tower shadow. In this paper, we present a holistic design solution to integrate active load control using a controllable Gurney flap based on plasma actuators. We illustrate the design solution for a land-based 3.4-MW wind turbine rotor. Comparisons to a baseline reference 3.4-MW wind turbine show significant load reduction (15–18% DEL reduction for flap-wise blade root moments), rotor mass reduction (5–8%), and LCOE reduction (1.16–3.11%). To achieve these results, a comprehensive sequential-iterative design procedure is introduced to integrate the controllable Gurney flap into the turbine design and to drive the design solution toward the best LCOE reduction solution. Results are presented for mapping fatigue load reductions into cost reductions. In addition, an evaluation of active load control extended from Region-III to also include Region-II showed a further 34% reduction in DEL.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2023

XCT System for Harvesting In-Current Hydrokinetic Energy from Low-Velocity Sites

The Project demonstrated the functionality of a cross cutting (XCT) type turbine in laboratory and open water testing. The fundamental design approach of locating small axial rotors near the ends of driving spars, which pull the rotors through the water at a multiple of the free-stream velocity eliminates the need (and thus the cost) for a gearbox and torque resisting structures. This configuration, however, introduces the complexity of transmitting electricity across a rotating interface. Even so, cost models indicate that depending on the anchoring and mooring system, LCOE less than $0.10/kWh should be possible in high capacity-factor sites with non-reversing currents.

13 HYDRO ENERGY↗
DOE OSTI2022

Active rotor coning for a 25 MW downwind offshore wind turbine

A two-bladed downwind turbine system was upscaled from 13.2 MW to 25 MW by redesigning aerodynamics, structures, and controls. In particular, three 25-MW rotors were developed, and the final version is a fully redesigned model of the original rotor. Despite their radically large sizes, it was found that these 25-MW turbine rotors satisfy this limited set of structural design drivers at the rated condition and that larger blade lengths are possible with conewise load-alignment. In addition, flapwise morphing (varying the cone angle with a wind-speed schedule) was investigated to minimize mean and fluctuating blade root bending loads using steady inflow proxies for the maximum and lifetime damage equivalent load moments. Compared to the fixed coned rotor case, morphing can provide an Annual Energy Production (AEP) increase of 6%, and the maximum blade root flapwise bending moment increases 21% (still under the constraint, i.e., 10% of the ultimate moments) as a trade-off. The resulting series of 25-MW rotors can be a valuable baseline for further development and assessment of ultra-large-scale wind turbines.

17 WIND ENERGY↗
DOE OSTI2022

Flutter behavior of highly flexible blades for two- and three-bladed wind turbines

Abstract. With the progression of novel design, material, and manufacturing technologies, the wind energy industry has successfully produced larger and larger wind turbine rotor blades while driving down the levelized cost of energy (LCOE). Though the benefits of larger turbine blades are appealing, larger blades are prone to aeroelastic instabilities due to their long, slender, highly flexible nature, and this effect is accentuated as rotors further grow in size. In addition to the trend of larger rotors, non-traditional rotor concepts are emerging including two-bladed rotors and downwind configurations. In this work, we introduce a comprehensive evaluation of flutter behavior including classical flutter, edgewise vibration, and flutter mode characteristics for two-bladed, downwind rotors. Flutter speed trends and characteristics for a series of both two- and three-bladed rotors are analyzed and compared in order to illustrate the flutter behavior of two-bladed rotors relative to more well-known flutter characteristics of three-bladed rotors. In addition, we examine the important problem of blade design to mitigate flutter and present a solution to mitigate flutter in the structural design process. A study is carried out evaluating the effect of leading edge and trailing edge reinforcement on flutter speed and hence demonstrates the ability to increase the flutter speed and satisfy structural design requirements (such as fatigue) while maintaining or even reducing blade mass.

Chetan, Mayank (ORCID:0000000241978801)↗
DOE OSTI2022

Parked aeroelastic field rotor response for a 20% scaled demonstrator of a 13‐MW downwind turbine

Abstract Aeroelastic parked testing of a unique downwind two‐bladed subscale rotor was completed to characterize the response of an extreme‐scale 13‐MW turbine in high‐wind parked conditions. A 20% geometric scaling was used resulting in scaled 20‐m‐long blades, whose structural and stiffness properties were designed using aeroelastic scaling to replicate the nondimensional structural aeroelastic deflections and dynamics that would occur for a lightweight, downwind 13‐MW rotor. The subscale rotor was mounted and field tested on the two‐bladed Controls Advanced Research Turbine (CART2) at the National Renewable Energy Laboratory's Flatiron Campus (NREL FC). The parked testing of these highly flexible blades included both pitch‐to‐run and pitch‐to‐feather configurations with the blades in the horizontal braked orientation. The collected experimental data includes the unsteady flapwise root bending moments and tip deflections as a function of inflow wind conditions. The bending moments are based on strain gauges located in the root section, whereas the tip deflections are captured by a video camera on the hub of the turbine pointed toward the tip of the blade. The experimental results are compared against computational predictions generated by FAST, a wind turbine simulation software, for the subscale and full‐scale models with consistent unsteady wind fields. FAST reasonably predicted the bending moments and deflections of the experimental data in terms of both the mean and standard deviations. These results demonstrate the efficacy of the first such aeroelastically scaled turbine test and demonstrate that a highly flexible lightweight downwind coned rotor can be designed to withstand extreme loads in parked conditions.

17 WIND ENERGY↗
DOE OSTI2021

Conceptual monopile and tower sizing for the IEA Wind Task 37 Borssele reference wind farm

This paper explores the preliminary design of the support structures for the IEA Wind Task 37 reference wind farm at the Borssele site III and IV. The study looks at two different design methods that might be used within larger wind farm system design optimization (i.e. lay-out, electrical systems, etc.). The first consists of a scaling tool that scales a detailed design according to the rated power, water depth, hub height and rotor diameter. The second is a physics-based optimization approach that relies on the WISDEM® design tool. This research compares the results of these two methods for the design of both the tower and monopile of the IEA 10-MW and 15-MW reference wind turbines at a range of sea depths (25 m, 30 m, 35 m, 40 m). The two tools yield very similar results in terms of monopile base diameter, support structure natural frequency and mass. WISDEM is then used to also investigate the sensitivity of the design to the tower top forces, wave conditions and the soil conditions. It is shown that tower top forces dominate the design. In general, large diameter structures can carry additional costs associated with manufacturing and transportation requirements. Thus, the paper is concluded with a trade-off study between mass and diameter that quantifies the effect of the reduction in monopile diameter with the increase in structural mass.

WIND ENERGY↗
DOE OSTI2021

MADE3D: Enabling the next generation of high-torque density wind generators by additive design and 3D printing

Direct-drive wind turbine generators are increasing in popularity, thanks to recent project developments—especially offshore, where reliability and efficiency are major cost drivers. Yet, high capital costs are forcing many original equipment manufacturers to consider lightweight, high-torque density generators for next-generation multi-megawatt turbines that may be difficult to realize by traditional design or manufacturing methods. In this study, we present a new design framework enabled by advanced machine learning and multimaterial additive manufacturing to perform a magnetic topology optimization that maximizes the torque per rotor active mass for a 15-megawatt direct-drive permanent magnet wind generator. A comparison of the proposed approach against conventional topology optimization demonstrated a significant increase in computational efficiency and accuracy in performance predictions. Results using single and multimaterial compositions for rotor core and magnets identify a wider choice of 3D printable designs for a given specification. A hybrid combination of sintered and dysprosium-free polymer-bonded magnets shows good potential for torque performance by saving material costs up to 8.75%. More than 30% improvement in rotor torque densities is identified which can marginally improve the overall generator torque density. With the rapid evolution of multipowder deposition technolgies, this study can greatly inspire a new paradigm for design-driven manufacturing with novel material compositions and lightweight, low-cost, high-strength multimaterial geometries that were previously unexplored for direct-drive generators.

17 WIND ENERGY↗
DOE OSTI2021

MADE3D: Enabling the Next-Generation High-Torque- Density Wind Generators by Additive Design and 3D Printing

Direct-drive wind turbine generators are increasing in popularity, thanks to recent project developments - especially offshore, where reliability and efficiency are major cost drivers. Yet, high capital costs are forcing many original equipment manufacturers to consider lightweight, high-torque density generators for next-generation multi-megawatt turbines that may be difficult to realize by traditional design or manufacturing methods. In this study, we present a new design framework enabled by advanced machine learning and multimaterial additive manufacturing to perform a magnetic topology optimization that maximizes the torque per rotor active mass for a 15-megawatt direct-drive permanent magnet wind generator. A comparison of the proposed approach against conventional topology optimization demonstrated a significant increase in computational efficiency and accuracy in performance predictions. Results using single and multimaterial compositions for rotor core and magnets identify a wider choice of 3D printable designs for a given specification. A hybrid combination of sintered and dysprosium-free polymer-bonded magnets shows good potential for torque performance by saving material costs up to 8.75%. More than 30% improvement in rotor torque densities is identified which can marginally improve the overall generator torque density. With the rapid evolution of multipowder deposition technologies, this study can greatly inspire a new paradigm for design-driven manufacturing with novel material compositions and lightweight, low-cost, high-strength multimaterial geometries that were previously unexplored for direct-drive generators.

3D printing↗
DOE OSTI2021

Laboratory Wind Turbine Blade Static Testing of the Sandia National Rotor Testbed 13-Meter Wind Turbine Blade

The Sandia National Laboratories (SNL or Sandia) National Rotor Testbed (NRT) blade is a new design for experimental research and development at the Sandia Scaled Wind Farm Technology (SWiFT) facility, located at Texas Tech University’s National Wind Institute Research Center in Lubbock, TX. Four NRT blades were manufactured, with three blades for operation at the SWiFT facility, and one blade intended for structural validation. A series of structural validation tests including property testing, static strength testing, and fatigue testing were performed at the National Renewable Energy Laboratory (NREL). This report documents the static and fatigue load cases applied to the NRT blade.

17 WIND ENERGY↗
DOE OSTI2023

Design and Modeling of an Open-Source Baseline Floating Marine Turbine: Preprint

Marine energy resources such as river, tidal, and ocean currents can provide abundant, predictable, and clean power to both densely populated and remote communities globally. However, marine turbine technologies are still in an early stage of development. Recently, features have been added to the National Renewable Energy Laboratory's open-source wind turbine modeling tool OpenFAST to support the simulation of axial-flow marine turbines. These new features enable marine energy developers to predict the performance and safety of their turbines and allow researchers and students to advance the field through the exploration of novel designs. Developing and demonstrating the new capabilities of OpenFAST for marine turbines requires a baseline design that can be used as an example and test case. There are limited open-source turbine models suitable for this purpose. One existing baseline design is the Reference Model 1 (RM1), a fixed-bottom, dual-rotor marine turbine that was published in 2014 as part of the Department of Energy's Water Power Reference Model Project. To test and demonstrate OpenFAST's ability to model floating marine turbines, several modifications were made to the RM1. A floating platform and mooring system were designed to support a single RM1 rotor in a wide range of possible current and wave conditions. The system and model are intended to be a stable reference case and starting point for research efforts. The platform features all cylindrical members and familiar design elements from the offshore wind industry; the mooring system uses simple catenary chains. While not optimized for the lowest platform cost, the design is understandable and robust and can serve as a baseline for floating marine turbine technologies. This is a useful starting point for studies to explore new technologies or design methodologies. Additionally, the floating RM1 design enables cross-collaboration among industry, academia, and national lab researchers and serves as an educational platform for newcomers to marine energy. This short paper presents the specifications of the turbine, including its floating support structure and mooring system. The rationale behind the selection of certain design parameters is described. To enable adoption of this baseline case for research and educational efforts, an OpenFAST model of the full system has been made publicly available at https://github.com/OpenFAST/r-test/tree/main/glue-codes/openfast/MHK_RM1_Floating.

floating↗
DOE OSTI2022

Machine-learning identification of the variability of mean velocity and turbulence intensity for wakes generated by onshore wind turbines: Cluster analysis of wind LiDAR measurements

Light detection and ranging (LiDAR) measurements of isolated wakes generated by wind turbines installed at an onshore wind farm are leveraged to characterize the variability of the wake mean velocity and turbulence intensity during typical operations, which encompass a breadth of atmospheric stability regimes and rotor thrust coefficients. The LiDAR measurements are clustered through the k-means algorithm, which enables identifying the most representative realizations of wind turbine wakes while avoiding the imposition of thresholds for the various wind and turbine parameters. Considering the large number of LiDAR samples collected to probe the wake velocity field, the dimensionality of the experimental dataset is reduced by projecting the LiDAR data on an intelligently truncated basis obtained with the proper orthogonal decomposition (POD). The coefficients of only five physics-informed POD modes are then injected in the k-means algorithm for clustering the LiDAR dataset. The analysis of the clustered LiDAR data and the associated supervisory control and data acquisition and meteorological data enables the study of the variability of the wake velocity deficit, wake extent, and wake-added turbulence intensity for different thrust coefficients of the turbine rotor and regimes of atmospheric stability. Furthermore, the cluster analysis of the LiDAR data allows for the identification of systematic off-design operations with a certain yaw misalignment of the turbine rotor with the mean wind direction.

17 WIND ENERGY↗
DOE OSTI2025

Facets of hydro power and future trends in a Nordic Context

Hydropower technologies bolster high penetration of variable renewable energies (VREs) in the net zero emissions scenarios. Nevertheless, there are various challenges to meeting the ambitious goal, such as stability, reliability, resiliency, security, lack of reactive power, voltage support and inertia, large-scale storage deployment and coordination, interconnectedness, demand-side response, higher thermal cycles with increased start/stops, and inadequate Levelized Cost of Energy (LCOE) for system-wise VRE integration and profitability. This survey conducts a bottom-up analysis to unveil the opportunities to utilize hydropower facilities and disentangle the nested problem for intertwining design features, control algorithms, operation, optimization approaches, incentives, services, and market mechanisms using a three-pillar framework perspective: grid owners, power producers, and machine designers. The survey identified emerging trends in real-time and capacity markets, flexible power systems, and enhanced grid capabilities, including advanced voltage support and updated grid codes. These developments present significant opportunities for hydropower, such as achieving super-flexibility through hybridization, expanded reactive power capabilities, and advanced operational modes like a synchronous condenser and power adequator functionalities. These opportunities require novel design philosophies — including new winding, stator, and rotor configurations, optimized ventilation, and active cooling systems — to enhance performance under stressed grid and climate conditions. Finally, integrating climate and energy models for multi-basin optimization with finer spatial and temporal granularity enhances the planning accuracy for water management of hydropower while addressing environmental challenges. The review delivers helpful prospective suggestions and tools that would serve researchers, power engineers, and stakeholders in making decisions about hydropower technologies and services in 2050 and beyond.

13 HYDRO ENERGY↗
DOE OSTI2023

RAAW

High-fidelity wind turbine modeling advances necessitate model validation datasets of equally high fidelity. The Rotor Aerodynamics, Aeroelastics & Wake (RAAW) project was designed to address this need. This three-year project runs from October 2021 through October 2024 starting with a field data collection period followed by model validation activities. RAAW is a partnership between GE Renewable Energy and the United States Department of Energy (DOE) through the National Renewable Energy Laboratory (NREL) and Sandia National Laboratories. The field experiment is designed to make detailed measurements of the inflow, wind turbine response, and the resulting wake. The experimental dataset will be suitable for validating wind turbine models across the fidelity spectrum from actuator disk methods to blade-resolved codes.

17 WIND ENERGY↗
DOE OSTI2021

Conceptual Designs of the Structure of Inflatable Blades for Enabling Larger Turbines

Over the last couple of decades, increasingly larger rotor diameters have enabled significant reductions in the levelized cost of energy for wind through higher energy capture and improved capacity factors. But for onshore turbines, this has been met with manufacturing and transportation challenges. To enable larger onshore rotors, an innovative inflatable blade concept is investigated that employs both traditional and onsite manufacturing. The design architecture consists primarily of an inflatable aerodynamic shell attached to a factory-manufactured primary structure. Multiple architectures, cross-sectional topologies, and material combinations for the primary structure are investigated, as well as multiple skin materials. Structural cross-sectional characteristics are compared to a traditional blade, and inflatability and cost evaluations are presented. Results show that a box-beam architecture using only composite materials yields significant mass reduction with mature technologies/processes and modest cost decrease compared to traditional blade construction. This low-TRL study demonstrates the inflatable blade concept's techno-economic potential.

49 EE - Wind and Water Power Program - Wind (EE-4W↗
DOE OSTI2022

Turbomachine with internal bearing and rotor-spline interface cooling and systems incorporating the same

Aspects of the present disclosure include turbomachines designed and configured for high temperature and pressure operation and increased power level output that minimize pressure vessel design requirements, and increase dry gas seal reliability. In some examples, a first radial bearing is located in a high temperature and/or pressure region of the turbomachine between a rotor of the machine and a dry gas seal while other bearings are located outside of the high pressure region.

Fairman, Kevin D.↗
DOE OSTI2022

Field tests of a highly flexible downwind ultralight rotor to mimic a 13-MW turbine rotor

Offshore extreme-scale turbines of 20–25 MW in size may offer reduced energy costs. The technical barriers at these extreme scales include escalating blade masses with increased flexibility as well as high gravity loads and tower-strike issues. These barriers may be addressed with a load-aligning downwind turbine. To investigate this type of design, a field test campaign was conducted with an aeroelastically scaled rotor, termed the Segmented Ultralight Morphing Rotor Demonstrator (SUMR-D). The tests were conducted on the Controls Advanced Research Turbine at the National Renewable Energy Laboratory. The paper gives an overview of the experimental diagnostics, blade design, and results of the field campaign, as well as makes conclusions and recommendations regarding extreme-scale highly flexible downwind rotors.

17 WIND ENERGY↗