Search NASA⌕ Search

SEARCH · Search NASA

Results for “salt behavior”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Unconventional desalination: The use of cyclone separators in HDH desalination to achieve zero liquid discharge

Research in water desalination technologies is constantly growing to meet global demands for freshwater. Though acting to meet these demands, the rapid growth and spread of desalination technologies poses environmental issues due to the increasing brine concentrates that are ultimately discharged back to nature. This article presents a cyclone separator to transform a humidification-dehumidification (HDH) cycle to a dual-product cycle to produce freshwater and solid salt crystals for highly saline streams. A desalination cycle equipped with a cyclone separator is used to treat water with 3.5%–81% salinity. The separation efficiency is well above 99% and can produce potable water from hyper saline feed in a once-through process. Further, the cyclone separator performance was tested under different conditions including humidity ratios, relative humidities, and feed stream's salinities. The cyclone separator is self-cleaning and overcomes salt scaling. This behavior is a direct function of the walls' temperature and the carrier air dew point. Self-cleaning capability allows the cyclone separator to treat feed water of extreme salinities (up to 810,000ppm) down to freshwater salinity with zero liquid discharge. The cyclone separator was utilized in a novel HDH desalination technology to treat different salinities. The product was freshwater of salinity <500ppm.

42 ENGINEERING↗
DOE OSTI2023

Optical spectroscopy of molten fluorides: Methods, electronic and vibrational data, structural interpretation, and relevance to radiative heat transfer

In this study, to help address the need for predicting radiative heat transfer (RHT) behavior of molten salts, we conducted a comprehensive review of methods and data from optical spectroscopic measurements on molten fluoride salts. Transmittance, reflectance, and trans-reflectance experimental methods are discussed, along with the corresponding data reduction methodology and the limitations of each technique. Optical spectroscopy is a convenient indirect probe for changes in structural parameters with temperature and composition. Electronic and vibrational absorption data for transition-metal, lanthanide, and actinide solutes and vibrational absorption data for alkali and alkaline earth fluoride solvents are compiled, and the corresponding structural interpretation is discussed and compared with other experimental and theoretical work. We find that solvent and solute vibrational absorption can be significant in the mid-infrared, resulting in near-infrared edges of significance to RHT. Extrapolation and averaging of existing edge data leads to estimated gray absorption coefficient values at 700 °C of 546 m —1 for FLiBe and 276 m —1 for FLiNaK, both within the range of 1 – 6000 m —1 identified to be of engineering relevance for radiative heat transfer analysis.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Survey of Dynamic Mode Decomposition Methods

Dynamic mode decomposition (DMD) is a data-driven reduced order modeling (ROM) technique used for dynamic systems. The widely adopted algorithm was first introduced and demonstrated on fluid flow data by Schmid. In recent years, various other fields, such as nuclear engineering, have begun to adopt this method. For example, DMD has been used for estimating α-eigenvalues, as an ROM for pulsed neutron problems, for predicting isotopic composition in burnup calculations, as acceleration techniques for iterative methods, and in capturing dynamic behaviors in molten salt reactor transients. This report seeks to demonstrate the capabilities and limits of the standard DMD algorithm, and identify problem spaces where variants may be better suited. The primary variant this report considers is Multi-Resolution DMD (mrDMD). Because this serves as a survey, synthetically produced data is used in lieu of simulation results. The remainder of this report will go into detail on the DMD theory, outline the standard DMD and mrDMD algorithms, present test cases highlighting the applicability of each, and finally present a discussion on how to determine the best suited algorithm for a given problem. All calculations performed in this report are carried out using the open source DMD library, PyDMD.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
NASA NTRS1984

Stress-corrosion behavior of aluminum-lithium alloys in aqueous salt environments

The stress corrosion susceptibility of two powder metallurgy (P/M) alloys, Al-Li-Cu and Al-Li-Cu-Mg; two mechanically attrited (M/A) alloys, Al-Li-Cu and Al-Li-Mg; and two wrought, ingot alloys, X-2020 and AA7475, are compared. Time-dependent fracture in an aqueous sodium chloride environment under alternate immersion condition was found to vary significantly between alloys. The stress corrosion behavior of the two powder metallurgy processed alloys was studied in detail under conditions of crack initiation, static crack growth, and fatigue crack growth. A variety of stress corrosion tests were performed including smooth surface, time-to-failure tests; potentiostatic tests on smooth surfaces exposed to constant applied strain rates; and fracture mechanics-type tests under static and cyclic loads. Both alloys show surface pitting and subsequent intergranular corrosion. Pitting is more severe in the magnesium-bearing alloy and is associated with stringer particles strung along the extrusion direction as a result of P/M processing.

Pizzo, P. P.↗
DOE OSTI2024

Applications of Thermochemical Modeling in Molten Salt Reactors

The extensively evaluated and consistent thermodynamic database, the Molten Salt Thermal Properties Database—Thermochemical (MSTDB-TC), was used along with additional thermodynamic values from other sources as examples of ways to examine molten salt reactor (MSR) fuel behavior. Relative stability with respect to halide potential and temperature for likely fuel and fission product components were mapped in Ellingham diagrams for the chloride and fluoride systems. The Ellingham diagrams provide a rich, visual means for identifying halide-forming components in proposed fuel/solvent salt systems. Thermochemical models and values from MSTDB-TC and ancillary sources were used in global equilibrium calculations to provide compositions for a close analysis of the behavior of a possible Molten Chloride Salt Fast Reactor and a Molten Salt Reactor Experiment-type system at high burnup (100 GWd/t). The results illustrated the oxidative nature of burnup in MSRs and provided information about redox behavior and possible control.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Computational and experimental analysis of structural and Thermophysical properties of LiX-KX (X = chloride, iodide, or bromide) molten salts

Molten salts containing lithium (Li) and potassium (K) halides, including chlorides (Cl), bromides (Br), and iodides (I), are pivotal in advanced technological applications including nuclear reactor technologies, thermal batteries, and industrial pyrochemical processes. Despite their significance, the availability of the temperature-dependent structural and thermophysical properties of these molten salts remain scarce. Here, this study addresses this knowledge gap by predicting and measuring the key properties such as coordination number, radial distribution function, density, heat capacity, and volumetric thermal expansion of molten LiI-KI, LiBr-KBr and LiCl-KCl eutectic mixtures. Utilizing ab initio molecular dynamics (AIMD) simulations, we predict these properties of LiX-KX (X=Br,I, Cl) across various temperatures, with chlorides as a benchmark. Experimental measurements using Archimedes methods and Differential Scanning Calorimetry validate the densities and heat capacities of these molten salts. Our comprehensive analysis of the structural and thermophysical properties provides critical insights into the behavior of these molten salts at various temperatures, enhancing the understanding necessary for their application in advanced technologies.

36 - MATERIALS SCIENCE↗
DOE OSTI2024

Development and Experimental Validation of a Heat Transfer Model for Spilled Molten Salt Pools

A spill of radionuclide-bearing molten salt is one of the major postulated events that needs to be analyzed for liquid fluorine salt-cooled high-temperature reactor (FHR) or molten salt reactor licensing purposes. In this postulated event, radioactive source term materials (RSTMs) in the molten salt are discharged from the reactor vessel to the reactor building. The release of RSTMs from the spilled salt pool to the gas space in the reactor building is expected to be controlled by the cooling behavior of the spilled salt, including the growth and shrinkage of the solid crust on the surface of the spilled salt pool. This paper presents a simulation model for spilled salt pool heat transfer and validation efforts. The validation data come from two molten salt spill tests that were performed recently: the PELE2 test by the Rapid Experimental Laboratory of Kairos Power LLC (KP) and the Argonne salt cooling test conducted by Argonne National Laboratory. The former was a large-scale test involving kilograms of molten spilled FLiNaK salt, and the latter was a relatively smaller-scale test targeting various processes associated with a salt spill event. Both tests generated valuable data sets that can be used to assess salt cooling and validate evaluation models. This paper provides a new one-dimensional model that can simulate the cooling process of a spilled salt pool as well as the thermal responses of heat structures, such as the stainless steel liner and the concrete below the salt. The model has been implemented as part of KP-SAM code, which is a branch of the systems code SAM specific to KP FHR. In conclusion, the simulation results of the model are compared with the data of the PELE2 and Argonne tests, and reasonable agreements are observed between the model and test data.

heat transfer model↗
NASA NTRS1975

Stress corrosion cracking of Ti-8Al-1 Mo-1V in molten salts

The stress corrosion cracking (SCC) behavior of Ti-8Al-1 Mo-1V has been studied in several molten salt environments. Extensive data are reported for the alloy in highly pure LiCl-KCl. The influence of the metallurgical heat treatment and texture, and the mechanical microstructure show similarities with aqueous solutions at lower temperature. The fracture path and cracking modes are also similar to that found in other environments. The influence of H2O and H(-) in molten LiCl-KCl lead to the conclusion that hydrogen does not play a major role in crack extension in this environment.

Smyrl, W. H.↗
DOE OSTI2025

Evaluate Compatibility of Alloy 244 in NaCl-MgCl 2

Alloy 244 is a potential material of interest for molten salt reactor (MSR) developers employing molten chloride as fuel and coolant salts because of its improved mechanical properties compared to the austenitic stainless steel 316H and the Ni-base alloy Hastelloy-N. However, data are limited on the corrosion behavior of alloy 244 in molten chloride salts. Experimental data on the corrosion behavior of 244 in chloride salts will provide valuable data to MSR developers while simultaneously aiding in improving mechanistic understanding of the role of salt chemistry, alloying constituents and microstructure of 244. This task evaluated the compatibility of alloy 244 in two different eutectic NaCl–MgCl 2 salt mixtures. Similar corrosion behavior in terms of depths of attack and compositional changes in the alloy subsurface was observed after exposure in both salts for 500 h at 750°C. However, severe corrosion attack was observed after 500 h at 850°C in one of the chloride salt mixture. This was most likely due to the combined effects of the differences in the two salt chemistries, distinct microstructure of 244 at 850°C compared to 750°C, and the temperature dependence of the chemical interactions (thermodynamic and kinetic) between the alloying constituents.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Comparing Experimental Phase Behavior of Ion-Doped Block Copolymers with Theoretical Predictions Based on Selective Ion Solvation

The effects of salt-doping on the morphological behavior of block copolymers are well established but remain poorly understood, partially because of the challenge of resolving electrostatics in a heterogeneous medium with low average permittivity. By employing a recently developed field theory, we analyze the phase behavior of polystyrene-b-poly(ethylene oxide) (SEO) copolymers doped with lithium bis(trifluoromethanesulfonyl)imide salts (LiTFSI). Using a single fitting parameter, the ionic solvation radius, we obtain qualitative agreement between our theory and experimental data over a range of polymer molecular weights and copolymer compositions. Such agreement supports and highlights the need of solvation free energy to accurately describe the self-assembly of ion-doped block copolymers and demonstrates that experimentally observed dependence on molecular weight, not present in neutral block copolymers, can be rationalized by solvation effects. Overall, morphological variations are stronger than those predicted by the leading, linear order theory but can be captured by the full model.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Effect of oxide impurities on the corrosion behavior of structural materials in molten LiF-NaF-KF

The corrosion of materials in molten fluoride salts is largely influenced by the presence of impurities in the salt. Very few studies have been done on the effect of oxide impurities on the corrosion of structural alloys in molten fluoride salts. In this study, corrosion behavior of selected alloys was studied in molten FLiNaK with the addition of different oxides such as Li 2 O, NiO, and Cr 2 O 3 . The results show that addition of oxides can lead to significant effects on this corrosion, depending on the type and amount of oxide added and the alloy being used.

14 SOLAR ENERGY↗
DOE OSTI2026

Disentangling cation effects on ion mobility and structure in ionic liquid electrolytes

Ionic liquids (ILs) are low-temperature molten salts, where ion transport is primarily governed by ion–ion interactions. Yet, the impact of organic IL cations on critical electrolyte properties such as ion dissociation and overall transport behavior in lithium-salt-doped ILs remains poorly understood. Moreover, despite their critical role in designing IL-based electrolytes for energy storage applications, ion–ion interactions and ion-specific transport under an applied electrical potential are seldom quantified, largely due to the unique experimental and computational challenges involved. Herein, we compare transport properties obtained using 1 H, 7 Li, and 19 F pulsed-field gradient nuclear magnetic resonance (NMR) and electrophoretic NMR (eNMR) with those measured by electrochemical impedance spectroscopy. Non-equilibrium molecular dynamics (MD) simulations and eNMR confirm the presence of negatively charged [Li(TFSI) n ] (1−n) aggregates that migrate towards the positive electrode, resulting in negative lithium transference numbers. Equilibrium MD simulations reveal a vehicular Li ion transport mechanism facilitated by long-lived aggregates with Li + cations strongly bound to multiple TFSI − anions. Finally, we observe an inverse relationship between the apparent charge of the TFSI − anion in the neat IL, which is dictated by the IL cation, and Li + transport in the salt-doped systems. This highlights the opportunity to tune electrolyte performance by tailoring cation chemistry.

Li-ion batteries↗
DOE OSTI2021

Tribological behavior of ceramic-alloy bearing contacts in molten salt lubrication for concentrating solar power

Molten salts are considered as candidate heat transfer fluids and thermal energy storage media for next generation concentrating solar power (CSP). A molten salt circulates inside the piping and heat exchanger and also functions as a lubricant for the sleeve bearings of the CSP pump. Furthermore, wear- and corrosion-resistant high-temperature bearing materials are critical for the pump efficiency and durability. This study evaluated the tribological performance of candidate bearing materials in lubrication of a molten chloride salt mixture (20% NaCl + 40% MgCl 2 + 40% KCl) at 750 °C in an inert argon gas (a simulative CSP pump environment). Six ceramic-alloy pairs were tested, zirconia and silicon nitride against Haynes 244, Hastelloy C276, and Tribaloy T900 alloy, and ranked by the friction coefficient and wear loss. Characterization of worn surfaces suggested the wear mechanism as a combination of abrasion, adhesion, and tribocorrosion. Results from this study provide fundamental insight for the development and selection of bearing materials for molten salt powered CSP pumps.

14 SOLAR ENERGY↗
DOE OSTI2024

Modeling the Impact of Grain Size on Corrosion Behavior of Ni-Based Alloys in Molten Chloride Salt via Cellular Automata

Molten chloride salts hold significant promise as both thermal transfer and storage media for next-generation concentrated solar power (CSP) systems. However, molten chlorides pose a considerable corrosion risk to structural materials, particularly Ni-based alloys. One approach to enhancing corrosion resistance is through the optimization of grain structure; however, it remains uncertain whether increasing or decreasing grain size enhances corrosion resistance. A cellular automata (CA) program was developed to evaluate the interplay between grain size and corrosion in Ni-based alloy. Our CA program tracks alloy composition, surface roughness, and thickness loss via a graphical user interface, displaying corrosion and diffusion status, and multiple user input cards for tuning the simulation. CA simulations of Inconel 625 indicate enhanced corrosion resistance with increased grain size, with passivating oxides offering limited protection. Additionally, the temporal evolution of alloy surface roughness demonstrates notable fluctuations, with abrupt increases attributed to corrosion along vertical grain boundaries and sudden decreases to grain detachment from the protective film.

Materials Science↗
DOE OSTI2021

A solid electrolyte interphase to protect the sulfurized polyacrylonitrile (SPAN) composite for Li–S batteries: computational approach addressing the electrolyte/SPAN interfacial reactivity

This study addresses the reactivity of multiple solvents and lithium bis(fluorosulfonyl)imide (LiFSI) at the interface with sulfurized polyacrylonitrile (SPAN) in multiple stages of lithiation via ab initio molecular dynamics simulations. Here, both ether 1,3-dioxolane (DOL) and dimethyl carbonate (DMC) proved stable on the lithiated SPAN surface regardless of the lithium content, meaning that neither of these species likely contributes to growing a solid electrolyte interphase (SEI) coating to protect the SPAN composite. Conversely, cyclic carbonates, ethylene carbonate (EC) and fluoroethylene carbonate (FEC) are shown to be very active. The EC reduction occurs only on a highly lithiated surface with a 3.0 Li/S molar ratio, the equivalent of the SPAN composite in an over-discharge regime with voltages close to 0.0 V vs. Li/Li + . The FEC reduction starts with a 2.0 Li/S molar ratio and above, suggesting that FEC could act as a useful additive in electrolyte formulations with EC. Both EC and FEC follow multiple reduction mechanisms to produce complex reduction products and LiF in the FEC case. We provide a mechanistic description for each detected decomposition path. The LiFSI salt also proves reactive against the lithiated SPAN surface. The FSI – defluorination is the dominant reduction path. However, the SO 2 NSO 2 F – and SO 2 NSO 2 2– species proved stable against S–N cleavage. This behavior makes the LiFSI salt a potential candidate for SPAN-based Li–S batteries because it produces LiF without releasing SO 2 .

25 ENERGY STORAGE↗
NASA NTRS1988

Thermal analysis of heat storage canisters for a solar dynamic, space power system

A thermal analysis was performed of a thermal energy storage canister of a type suggested for use in a solar receiver for an orbiting Brayton cycle power system. Energy storage for the eclipse portion of the cycle is provided by the latent heat of a eutectic mixture of LiF and CaF2 contained in the canister. The chief motivation for the study is the prediction of vapor void effects on temperature profiles and the identification of possible differences between ground test data and projected behavior in microgravity. The first phase of this study is based on a two-dimensional, cylindrical coordinates model using an interim procedure for describing void behavor in 1-g and microgravity. The thermal analysis includes the effects of solidification front behavior, conduction in liquid/solid salt and canister materials, void growth and shrinkage, radiant heat transfer across the void, and convection in the melt due to Marangoni-induced flow and, in 1-g, flow due to density gradients. A number of significant differences between 1-g and o-g behavior were found. This resulted from differences in void location relative to the maximum heat flux and a significantly smaller effective conductance in 0-g due to the absence of gravity-induced convection.

Wichner, R. P.↗
DOE OSTI2025

Molten Salt Corrosion Tests of Additively Manufactured Stainless Steel 316H

Molten salt reactors (MSRs) have drawn considerable interest due to their favorable safety features, high thermal efficiency, and compatibility with different fuel cycles. Yet, the success of MSRs hinges critically on the performance of structural materials to be used in these aggressive molten salt environments, where corrosion and material compatibility remain primary challenges to long-term reliability. Additively manufactured (AM) nuclear structural materials prompt the use of novel geometries and compositions to enhance material performance and reduce costs of constructing MSRs. The rapid solidification conditions inherent to AM processing impart distinctive microstructural features, including cellular sub-structures, dislocation densities, residual stress, and oxide inclusions, which can influence material performance in MSR components. While the mechanical properties of AM stainless steels have been widely studied, their corrosion behavior, particularly in molten salt environments, has received far less attention. Addressing these needs, the Advanced Materials and Manufacturing Technologies (AMMT) program provides a framework for systematically evaluating how unique microstructures produced by AM processes influence the performance of these materials in these demanding environments and for developing reproducible testing workflows that can support future code qualification efforts and standards development. Bridging this knowledge gap is essential for assessing the viability of AM alloys in MSRs and informing qualification strategies. A further challenge is the absence of standardized protocols for molten salt corrosion testing. Accordingly, this report provides an account of the corrosion evaluation of AM 316H stainless steel in NaCl 2 -MgCl 2 molten salt at 550 °C, with exposure times of 100 and 500 hours. It documents the experimental procedures implemented under the AMMT program, including salt preparation, exposure protocols, and post-test characterization methods, to establish reproducibility and transparency. Importantly, the study examines AM 316H samples in the as-fabricated condition, directly reflecting the surface state most relevant to engineering applications, and compares their behavior to machine-cut surfaces. Overall, preliminary evaluations have noted that surface conditions (e.g. morphology, contamination, etc.) have a noticeable impact on the corrosion resiliency. The impact of the corrosion is difficult to detect at 100h, unless, in the case of AM 316H, the specimen surface is decontaminated. After 500 h, as-fabricated surfaces of AM and wrought 316H display evidence of general versus preferential corrosion attack, respectively. Both AM and wrought 316H machine-cut surfaces exhibit a continuous Cr depletion zone, evident of general corrosion. While the estimated extent of corrosion appears within the same order of magnitude regardless of the surface condition, it is apparent that more predictable behavior is observed on machine-cut surfaces. Nonetheless, further investigation is necessary to fully elucidate the corrosion mechanism under these conditions.

36 - MATERIALS SCIENCE↗