SEARCH · Search NASA

Results for “skin”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

All sources NASA NTRS DOE OSTI

NASA NTRS1975

Skin friction reduction in supersonic flow by injection through slots, porous sections and combinations of the two

An experimental study of skin friction reduction in a Mach 3.0 air steam with gaseous injection through a tangential slot, a porous wall section, and combinations of the two was conducted. The primary data obtained were wall shear values measured directly with a floating element balance and also inferred from Preston Tube measurements. Detailed profiles at several axial stations, wall pressure distributions and schlieren photographs are presented. The data indicate that a slot provides the greatest skin friction reduction in comparison with a reference flat plate experiment. The porous wall section arrangement suffers from an apparent roughness-induced rise in skin friction at low injection rates compared to the flat plate. The combination schemes demonstrated a potential for gain.

Schetz, J. A.↗

NASA NTRS1975

Compliant wall-turbulent skin-friction reduction research

Previous compliant-wall experiments successful in reducing skin-friction drag probably have had a (unplanned) membrane resonance at a favorable frequency, amplitude, wave shape, length, and speed. The most probable drag reduction mechanism involves a direct coupling between the fluid and the moving wall when the wall natural resonance frequencies are near the fundamental turbulent burst frequency. Local skin-friction reductions of 61% were measured with mylar/PVC plastisol compliant surfaces. These reductions were observed only at certain flow conditions, indicating that changing tunnel total temperature may have altered the substrate dynamic modulus, damping, and coupled mylar tension. Apparently, the coupled membrane/substrate must be excited in compatible narrow-band natural frequency modes. An accelerated effort is required to develop practical durable compliant surfaces optimized for maximum drag reduction. Application of compliant walls to other transportation modes appears feasible with liquid flows offering the greatest skin-friction drag reduction potential.

Fischer, M. C.↗

NASA NTRS1975

Experimental verification of turbulent skin friction reduction with compliant walls

Preliminary compliant wall skin friction test results obtained in a low-turbulence pressure tunnel are reported. Compliant surface skins consisted of 0.0025 cm thick mylar, stretched under tension and area-bonded or longitudinally strip-bonded with silicone rubber adhesive to polyurethane foam. Mean velocity and fluctuating survey data were obtained with a single slanted hot wire. Mean velocity profiles for the area-bonded mylar surface skins indicated up to a 20% reduction in boundary-layer thickness (and lower momentum thickness) over rigid surfaces. This reduction in boundary-layer thickness indicates that a drag reduction occurred. In addition, a 16% reduction in wall shear was evident for the mylar/compressor foam compliant surface.

Weinstein, L. M.↗

NASA NTRS1976

An engineering procedure for calculating compressive strength of isogrid cylindrical shells with buckled skin

An engineering procedure is presented for calculating the compressive buckling strength of isogrid cylinders using shell of revolution techniques and accounting for loading beyond the material proportional limit and/or local buckling of the skin prior to general buckling. A general nondimensional chart is presented which can be used in conjunction with formulas based on simple deformation plasticity theory to calculate postbuckling stiffnesses of the skin. The stiffening grid system is treated as an equivalent isotropic grid layer. Stiffnesses are determined for this grid layer, when loaded beyond the proportional limit, by the same plasticity theory used for the skin and a nonlinear stress-strain curve constructed from simple isogrid-handbook formulas and standard-reference-manual stress-strain curves for the material involved. Comparison of prebuckling strains and buckling results obtained by this procedure with data from a large isogrid-cylinder test is excellent with the calculated buckling load no more than 4 percent greater than the test value.

Heard, W. L., Jr.↗

NASA NTRS1975

Mach and Reynolds number effects on turbulent skin friction reduction by injection

The investigation reported is concerned with questions regarding a possible Mach number influence on skin friction reduction caused by injection. The investigation shows that data considered by Danberg (1967) for the no-blowing skin friction coefficient are in error. Accurate profiles and local skin friction coefficient values are obtained when the influence of low Reynolds number amplification in the outer region of the boundary layer is included in a calculation method.

Bushnell, D. M.↗

NASA NTRS1975

Multiple slot skin friction reduction

The paper investigates analytically the effect of multiple slot injection on skin friction for a representative fuselage shape (ogive-cylinder body) and evaluates the potential of slot injection as a drag reduction system in subsonic flow. Typical CTOL cruise flight conditions (Mach number equals 0.82 at altitudes of 11 km) were adopted for a fuselage 67.06 m in length and with maximum diameter of 7.32 m. The numerical method of Price and Harris (1972) was used to calculate the boundary-layer characteristics up to the first slot, while the finite-difference method of Beckwith and Bushnell (1971) was used to calculate the velocity profile downstream of one, three, five, or ten slots. An integral expression is proposed for characterizing skin friction reduction effectiveness, and it is seen that large reductions in viscous drag (50%) are available through slot injection. Skin friction reduction is improved by increasing the number of injection slots but at a diminishing rate.

Howard, F. G.↗

NASA NTRS1977

Design and fabrication of graphite-epoxy bolted wing skin splice specimens

Graphite-epoxy bolted joint specimens were designed and fabricated. These specimens were to be representative of a side-of-body wing skin splice with a 20-year life expectancy in a commercial transport environment. Preliminary tests were performed to determine design values of bearing and net tension stresses. Based upon the information developed, a three-fastener-wide representative wing skin splice was designed for a load of 2627 KN/m (15,000 lbf/in.). One joint specimen was fabricated and tested at NASA. The wing skin splice failed at 106 percent of design ultimate load. This joint design achieved all static load objectives. Fabrication of six specimens, together with their loading fixtures, was completed, and the specimens were delivered to NASA-LRC.

Johnson, R. W.↗

NASA NTRS1980

Calculation of skin-friction coefficients for low Reynolds number turbulent boundary layer flows

An analysis is presented of the reliability of various generally accepted empirical expressions for the prediction of the skin-friction coefficient C/sub f/ of turbulent boundary layers at low Reynolds numbers in zero-pressure-gradient flows on a smooth flat plate. The skin-friction coefficients predicted from these expressions were compared to the skin-friction coefficients of experimental profiles that were determined from a graphical method formulated from the law of the wall. These expressions are found to predict values that are consistently different than those obtained from the graphical method over the range 600 Re/sub theta 2000. A curve-fitted empirical relationship was developed from the present data and yields a better estimated value of C/sub f/ in this range. The data, covering the range 200 Re/sub theta 7000, provide insight into the nature of transitional flows. They show that fully developed turbulent boundary layers occur at Reynolds numbers Re/sub theta/ down to 425. Below this level there appears to be a well-ordered evolutionary process from the laminar to the turbulent profiles. These profiles clearly display the development of the turbulent core region and the shrinking of the laminar sublayer with increasing values of Re/sub theta/.

Barr, P. K.↗

NASA NTRS1981

Skin friction drag measurements by LDV

A laser Doppler velocimeter employing a microscope objective as the receiving lens has been developed for measuring fluid velocity inside the boundary layer flow field with a spatial resolution of 40 microns. The method was applied for direct measurement of aerodynamic skin friction drag from the measured velocity gradient at the wall. Experimental results obtained on skin friction and on velocity components in a turbulent boundary layer on a low speed wind tunnel showed good agreement with previously reported data using conventional instruments such as hot-wire anemometers and Preston tubes. The method thus provides a tool for measurement and control of skin friction on aerodynamic bodies without perturbing the flow field.

Mazumder, M. K.↗

NASA NTRS1982

Measurement and visualization of skin friction on the leeside of delta wings in supersonic flow

The reported investigation was conducted with the aid of the NASA Ames High Reynolds Number Wind Tunnel. The flow conditions considered involved free stream Mach numbers of 2 and 3, and a Reynolds number of approximately 10,000,000 p. m. The employed model was a delta wing with an angle of 70 deg. A method reported by Tanner (1977) was used for the measurement of the skin friction. This method involves the use of a laser interferometer to determine the change in the thickness of an oil film. The procedure can also be employed for a visualization of skin friction in the form of interferograms. The investigation shows that skin friction measurements can provide a significant contribution to a physical understanding of the flow processes at the delta wing.

Szodruch, J.↗

NASA NTRS1983

Adapter for mounting a microphone flush with the external surface of the skin of a pressurized aircraft

A mounting device for securing a microphone pick up head flush with respect to the external surfaces of the skin of an aircraft for detecting shock waves passing thereover is described. The mount includes a sleeve mounted internally of the aircraft for capturing and supporting an electronics package having the microphone pick up head attached thereto in a manner such that the head is flush with the external surface of the aircraft skin and a pressure seal is established between the internal and external surfaces of the aircraft skin.

Cohn, R. B.↗

NASA NTRS1983

Late skin damage in rabbits and monkeys after exposure to particulate radiations

Preliminary results are reported of experiments on the late effects of exposure to particulate radiations on stem cell populations. Skin biopsies were taken from the ears of rabbits irradiated 2-5 years previously with 530 MeV/amu Ar ions (LET 90 keV/micron), or 365 MeV/amu Ne ions (LET 35 keV micron), and from the chests and inner thighs of rhesus monkeys irradiated 16-18 years previously with 32-MeV protons (LET about 1.2 keV/micron). Skin fibroblast cultures obtained from the biopsy samples in rabbits were observed to undergo dose-dependent decreases in in vitro life span, with estimated survival curves showing the effects of Ar-ion irradiation to be more severe than those of Ne-ion irradiation. In addition, the healing of the biopsy wound was observed to become slower as radiation dose increased. In the monkey, radiation reduced the average number of fibroblasts at the time of cessation of growth in culture. Results thus demonstrate the capacity of skin sampling to reveal stem cell destruction, and have important implications for astronauts and other persons at risk of particle exposure with regard to healing responses to trauma or surgery.

Bergtold, D. S.↗

NASA NTRS1984

Skin-stiffener interface stresses in composite stiffened panels

A model and solution method for determining the normal and shear stresses in the interface between the skin and the stiffener attached flange were developed. An efficient, analytical solution procedure was developed and incorporated in a sizing code for stiffened panels. The analysis procedure described provides a means to study the effects of material and geometric design parameters on the interface stresses. These stresses include the normal stress, and the shear stresses in both the longitudinal and the transverse directions. The tendency toward skin/stiffener separation may therefore be minimized by choosing appropriate values for the design variables. The most important design variables include the relative bending stiffnesses of the skin and stiffener attached flange, the bending stiffness of the stiffener web, and the flange width. The longitudinal compressive loads in the flange and skin have significant effects on the interface stresses.

Wang, J. T. S.↗

NASA NTRS1986

Recent skin friction techniques for compressible flows

A brief review is given of developments over the last decade in techniques for the measurement of skin friction in compressible airflows. Emphasis is placed on mean measurements beneath turbulent boundary layers in the supersonic and hypersonic flow regimes. Recent improvements in existing techniques such as the skin friction balance, Preston tube, sublayer fence, and heat transfer analogy are discussed. New or potential techniques including optical and acoustic measurements are also treated. Finally, new results are presented on the adaptation of the recently-developed laser interferometer skin friction meter for use in high-speed wind tunnels.

Settles, G. S.↗

NASA NTRS1989

Flight Balance For Skin-Friction Measurements

Skin-friction balance (flight balance) for use in flight on aircraft fuselage incorporates type-one, closed-loop control to make direct skin-friction force measurements. Curved surface element 2 in. (5.08 cm) in diameter used to sense tangential force of airstream passed over it. Linear electromagnetic force motor exerts restoring force that nulls position of sensing element. Applied skin-friction force measured by sensing amount of current through motor necessary to maintain null position. Unit is rugged, accurate, reliable, and easy to operate. Insensitivity of balance to background rectilinear vibrations and ability to sustain large transient loads during takeoffs and landings make it attractive for flight testing.

Tcheng, Ping↗

NASA NTRS1988

Water intrusion in thin-skinned composite honeycomb sandwich structures

Thin-skinned composite honeycomb sandwich structures from the trailing edge of the U.S. Army's Apache and Chinook helicopters have been tested to ascertain their susceptibility to water intrusion as well as such intrusions' effects on impact damage and cyclic loading. Minimum-impact and fatigue conditions were determined which would create microcracks sufficiently large to allow the passage of water through the skins; damage sufficient for this to occur was for some skins undetectable under a 40X-magnification optical microscope. Flow rate was a function of moisture content, damage, applied strain, and pressure differences.

Jackson, Wade C.↗

NASA NTRS1989

Skin friction balance

A skin friction balance uses a parallel linkage mechanism to avoid inaccuracies in skin friction measurement attributable to off-center normal forces. The parallel linkage mechanism includes a stationary plate mounted in a cage, and an upper and lower movable plate which are linked to each other and to the stationary plate throught three vertical links. Flexure pivots are provided for pivotally connecting the links and the plates. A sensing element connected to the upper plate moves in response to skin friction, and the lower plate moves in the opposite direction of the upper plate. A force motor maintains a null position of the sensing element by exerting a restoring force in response to a signal generated by a linear variable differential transformer (LVDT).

Ping, Tcheng↗

NASA NTRS1990

Polymer/riblet combination for hydrodynamic skin friction reduction

A process is disclosed for reducing skin friction and inhibiting the effects of liquid turbulence in a system involving the flow of a liquid along the surface of a body, e.g., a marine vehicle. This process includes injecting a drag reducing polymer into the valleys of adjacent, evenly spaced, longitudinal grooves extending along the length of the surface of the body, so that the rate of diffusion of the polymer from individual grooves into the liquid flow is predictably controlled by the groove dimensions. When the polymer has diffused over the tips of the grooves into the near wall region of the boundary layer, the polymer effectively reduces the turbulent skin friction. A substantial drag reducing effect is achieved with less polymer than must be used to lower skin friction when the surface of the body is smooth.

Bushnell, Dennis M.↗