Search NASA⌕ Search

SEARCH · Search NASA

Results for “smoothers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Orientation-dependent stabilization of MgCr 2 O 4 spinel thin films

AB 2 O 4 normal spinels with a magnetic B site can host a variety of magnetic and orbital frustrations leading to spin-liquid phases and field-induced phase transitions. Here, we report the epitaxial growth of (111)-oriented MgCr 2 O 4 thin films. By characterizing the structural and electronic properties of films grown along the (001) and (111) directions, the influence of growth orientation has been studied. Despite distinctly different growth modes observed during deposition, the comprehensive characterization reveals no measurable disorder in the cation distribution nor multivalency issue for Cr ions in either orientation. Contrary to a naive expectation, the (111) stabilized films exhibit a smoother surface and a higher degree of crystallinity than (001)-oriented films. The preference in growth orientation is explained within the framework of heteroepitaxial stabilization in connection to a significantly lower (111) surface energy. Furthermore, these findings open broad opportunities in the fabrication of two-dimensional kagome-triangular heterostructures with emergent magnetic behavior inaccessible in bulk crystals.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2023

Multifield ultralight dark matter

Ultralight dark matter (ULDM) is usually taken to be a single scalar field. Here we explore the possibility that ULDM consists of N light scalar fields with only gravitational interactions. This configuration is more consistent with the underlying particle physics motivations for these scenarios than a single ultralight field. ULDM halos have a characteristic granular structure that increases stellar velocity dispersion and can be used as observational constraints on ULDM models. In multifield simulations, we find that inside a halo the amplitude of the total density fluctuations decreases as $1/\sqrt{N}$ and that the fields do not become significantly correlated over cosmological timescales. Smoother halos heat stellar orbits less efficiently, reducing the velocity dispersion relative to the single field case and thus weakening the observational constraints on the field mass. Analytically, we show that for N equal-mass fields with mass m the ULDM contribution to the stellar velocity dispersion scales as 1/(Nm 3 ). Finally, lighter fields heat the most efficiently and if the smallest mass mL is significantly below the other field masses the dispersion scales as $1/(N^{2}m^3_L$).

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2024

Gravitational waves from binary neutron star mergers with a spectral equation of state

In numerical simulations of binary neutron star systems, the equation of state of the dense neutron star matter is an important factor in determining both the physical realism and the numerical accuracy of the simulations. Some equations of state used in simulations are C 2 or smoother in the pressure/density relationship function, such as a polytropic equation of state, but may not have the flexibility to model stars or remnants of different masses while keeping their radii within known astrophysical constraints. Other equations of state, such as tabular or piece-wise polytropic, may be flexible enough to model additional physics and multiple stars' masses and radii within known constraints, but are not as smooth, resulting in additional numerical error. We will study in this paper a recently developed family of equation of state, using a spectral expansion with sufficient free parameters to allow for a larger flexibility than current polytropic equations of state, and with sufficient smoothness to reduce numerical errors compared to tabulated or piece-wise polytropic equations of state. We perform simulations at three mass ratios with a common chirp mass, using two distinct spectral equations of state, and at multiple numerical resolutions. We evaluate the gravitational waves produced from these simulations, comparing the phase error between resolutions and equations of state, as well as with respect to analytical models. From our simulations we estimate that the phase difference at merger for binaries with a dimensionless weighted tidal deformability difference greater than Δ$\tilde{Λ}$=55 can be captured by the SpEC code for these equations of state.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2022

Early stage growth of amorphous thin film: Average kinetics, nanoscale dynamics, and pressure dependence

We used the coherent grazing incidence small angle x-ray scattering technique to study the average kinetics and nanoscale dynamics during early-stage a-WSi 2 sputter deposition. The kinetic and dynamic properties are examined as a function of pressure, which is known to be a critical factor in determining final surface roughness. Surface growth kinetics and dynamics are characterized by time parameters extracted from the height-height structure factor and correlation functions. The roughness at a given length scale reaches a maximum before relaxing down to a steady state. The lateral length scale dependence and pressure dependence are then compared among the measured kinetics and dynamics time parameters. Surfaces grown at lower pressures are smoother, leading to longer correlation times. The time parameters to reach a dynamic steady state and a kinetic steady state show contrasting pressure dependence. A dynamic steady state is reached earlier than the kinetic steady state at high pressure. A more random deposition direction and lower kinetic energy at higher pressures can explain these phenomena, along with the hypothesis that larger nanoclusters form in vapor before arriving at the surface. Here, a continuum model is applied to simulate the overall behavior with mixed success.

36 MATERIALS SCIENCE↗
DOE OSTI2025

A New Design Consideration for Bidirectional Resonant Converters

This paper introduces innovative design considerations for a bidirectional resonant converter, optimized for Electric Vehicle (EV) charging and vehicle-togrid (V2G) applications. By eliminating the need for complex voltage or current gain functions, the proposed design greatly simplifies the development process, making it more accessible for manufacturers and system integrators. This approach not only reduces engineering time and resource investment but also accelerates time-to-market, giving stakeholders a competitive edge in rapidly expanding EV infrastructure markets. In addition, the streamlined design ensures soft switching at maximum output power, leading to higher efficiency and improved durability, which translates to lower operating costs and a longer service life for EV charging equipment. These benefits provide a clear pathway to more cost-effective, scalable, and sustainable EV charging and V2G solutions, enhancing value for stakeholders by facilitating smoother integration into the grid and supporting energy resilience. To validate the benefits, a 60 kW bidirectional charger with a flexible input range of 700−900VDC and an output range of 400−1250VDC was developed, underscoring the design's adaptability and potential for large-scale implementation.

Asa, Erdem [ORNL] (ORCID:0000000190884812)↗
DOE OSTI2025

Improving Dynamic Wireless Charging System Performance For Electric Vehicles Through Variable Speed Limit Control Integration

Electric Vehicle (EV) charging has been a significant barrier to the widespread use of EVs. Traditional EV charging methods depend on cables, and there are concerns about safety, accessibility, convenience, and weather. A recent development, dynamic (or in-motion) wireless charging, enables EVs to charge wirelessly by incorporating charging infrastructure into roadways, allowing EVs to charge while moving. However, the energy transferred relies heavily on vehicle speed and time spent in the charging lane. This paper proposes an innovative solution that combines dynamic wire-less charging with Variable Speed Limit (VSL) control. This dynamic traffic control strategy adjusts speed limits based on real-time traffic, weather, and incidents. This integration of dynamic wireless charging and VSL has two potential benefits. First, it can motivate driver compliance with VSL through the incentive of charging. Second, it can promote smoother traffic flow and improve traffic safety by implementing lower speed limits at certain times. To verify these benefits, microscopic traffic simulations in SUMO were conducted under different EV penetration rates and VSL compliance rates. Simulation results reveal that the proposed approach can enhance dynamic wireless charging system performance while improving traffic flow and safety.

Xu, Guanhao [ORNL] (ORCID:0000000214326357)↗
DOE OSTI2021

Performance of III–V Solar Cells Grown on Reformed Mesoporous Ge Templates

We demonstrate a solar cell on reformed porous Ge with an efficiency of 7.7%. We generate mesopores in (100) Ge by bipolar electrochemical etching and anneal them at high temperature. The pores coalesce deep in the structure rather than at the surface as desired, although resulting in coarse superficial morphology unsuitable for device growth. To combat this issue, we developed a surface treatment involving an HBr dip, annealing at 415 degrees C, and a postannealing ultrasonic De-ionized water dip to improve the surface structure, resulting in a smoother reformed surface on which we grow a GaInAs solar cell. The structure retains embedded pores after growth and the transitions between Ge and III-V layers are distinct. The solar cell fabricated using the improved coalescence has an efficiency of 4.5%. The efficiency improves to 7.7% by isolating the rest of the device from three limiting localized shunt areas. Protruding defects in the porous Ge and III-V layers still limit the performance, but this work establishes a step toward the technical viability of this exfoliation approach, showing decent efficiency if protruding defects can be removed or reduced.

14 SOLAR ENERGY↗
DOE OSTI2021

Measurement of Local Differential Privacy Techniques for IoT-based Streaming Data

Various Internet of Things (IoT) devices generate complex, dynamically changed, and infinite data streams. Adversaries can cause harm if they can access the user’s sensitive raw streaming data. For this reason, protecting the privacy of the data streams is crucial. In this paper, we explore local differential privacy techniques for streaming data. We compare the techniques and report the advantages and limitations. We also present the effect on component (e.g., smoother, perturber) variations of distribution-based local differential privacy. We find that combining distribution-based noise during perturbation provides more flexibility to the interested entity.

Afrose, Sharmin↗
DOE OSTI2020

Reformed Mesoporous Ge for Substrate Reuse in III-V Solar Cells

Mesoporous Ge was generated by bipolar electrochemical etching of (100) Ge. Through high-temperature annealing experiments, we found that the mesoporous Ge microstructure produces pore coalescence deep in the structure rather than at the surface. III-V epitaxy on annealed porous Ge with subsurface coalescence and coral-like structures on the surface produced shunted photovoltaic devices. The roughness of the annealed porous Ge film was reduced by a pre-annealing HBr treatment and a post-annealing ultrasonic DI water dip. A smoother reformed surface was obtained, on which a GaInAs upright device with an efficiency of 5.7% was grown, demonstrating a first step towards technical viability.

14 SOLAR ENERGY↗
DOE OSTI2020

IEEE 1547-2018 Based Interoperable PV Inverter with Advanced Grid-Support Functions

Grid integration of photovoltaic (PV) inverters has been increasing in the past decade. As a result of the uncertainties introduced with high penetrations of PV, better monitoring and control of the PV inverters becomes crucial for improving overall system stability. This paper focuses on the communications capability of the inverter controller and on enabling interoperability. Multiple standards are available to enable interoperability in PV inverters. In this paper, an interoperable controller, enabled by Distributed Network Protocol 3 (DNP3) communications protocols, is developed for a grid-connected, three-phase PV inverter. The DNP3 server for the PV inverter is programmed on the real-time layer of the field-programmable gate array (FPGA)-based inverter controller. Set points for advanced inverter control functions, such as volt/VAr curves, ride-through curves, are sent from a DNP3 client, a simulated distribution management system application, to the PV inverter through DNP3. This communications capability of the inverter controller is validated using a controller-hardware-in-the-loop experimental setup. The code developed to achieve the interoperability is available in the public domain through open-source software licensing. This interoperability will enable smoother grid integration of smart PV inverters with advanced grid-support functions as well as allow better monitoring and control of PV inverters for grid stability.

14 SOLAR ENERGY↗
DOE OSTI2021

Vapor Treatment and In-situ Recrystallization by Copper Chloride on Cu(In,Ga)Se 2 Thin Film

Deposition of CIGS semiconductor thin films was performed at low temperature and high rate by three-stage coevaporation process on molybdenum coated glass substrate. Here, a vapor treatment was done in between the second and third stage by flashing CuCl 2 for 5 mins at 400 °C. A large change in morphology and crystal structure was observed after the treatment. XRD and SEM showed that small grains transformed into large grains. A smoother Ga profile was observed by SIMS measurements for the treated films as compared to as-deposited films. Furthermore, the Na profile was also modified in the recrystallized samples, with a lower content after recrystallization.

14 SOLAR ENERGY↗
DOE OSTI2024

Impacts of Superalloys on the Surface Quality of Additively Manufactured Channels

Abstract Gas turbines feature many components that require superalloys capable of handling extreme thermal environments. Increasing the selection of materials available for these components is important to their use in these extremely high-temperature environments. This study investigated two recently developed materials intended to be used for additive manufacturing (AM), with one superalloy based on cobalt and the other on nickel. Sets of four test coupons were built using the materials, in addition to the commonly used Inconel-718, on multiple laser powder bed fusion machines. Several build conditions were varied between coupon sets, including coupon orientation, contour settings, and upskin and downskin treatment. Each set of test coupons featured four unique cooling designs to explore how different cooling technologies would be impacted by the variations in build conditions. After being built, coupons were computed tomography (CT) scanned to determine accuracy to design intent and quantify the surface roughness. The CT scans indicated that horizontally built test coupons had a significantly higher deviation from design intent and higher surface roughness than those built vertically. Results also indicated that the cobalt-based alloy consistently had a smoother surface quality with lower surface roughness compared to the nickel-based alloy. After geometric characterization, the cooling performance of the test coupons was measured experimentally. Pressure losses were found to correlate with increases in surface roughness; however, in some cases, the convective heat transfer did not increase proportionally to the pressure loss as a result of surface features significantly blocking the flow without proportionally increasing convective heat transfer.

Engineering↗
DOE OSTI2022

Optimization of InGaN quantum well interfaces for fast interwell carrier transport and low nonradiative recombination

Efficient high-power operation of light emitting diodes based on InGaN quantum wells (QWs) requires rapid interwell hole transport and low nonradiative recombination. The transport rate can be increased by replacing GaN barriers with that of InGaN. Introduction of InGaN barriers, however, increases the rate of the nonradiative recombination. In this work, we have attempted to reduce the negative impact of the nonradiative recombination by introducing thin GaN or AlGaN interlayers at the QW/barrier interfaces. The interlayers, indeed, reduce the nonradiative recombination rate and increase the internal quantum efficiency by about 10%. Here, the interlayers do not substantially slow down the interwell hole transport; for 0.5 nm Al 0.10 Ga 0.90 N interlayers the transport rate has even been found to increase. Another positive feature of the interlayers is narrowing of the QW PL linewidth, which is attributed to smoother QW interfaces and reduced fluctuations of the QW width.

carrier transport↗
DOE OSTI2026

Optimal Transfer Operators in Algebraic Two-Level Methods for Nonsymmetric and Indefinite Problems

Consider an algebraic two-level method applied to the 𝑛-dimensional linear system 𝐴⁢𝒙 = 𝒃 using fine-space preconditioner (i.e., “relaxation” or “smoother”) 𝑀, with 𝑀 ≈ 𝐴, restriction and interpolation 𝑅 and 𝑃, and algebraic coarse-space operator 𝐴 𝑐 : = 𝑅 ∗ ⁢𝐴⁢𝑃. Then, what are the best possible transfer operators 𝑅 and 𝑃 of a given dimension 𝑛 𝑐 < 𝑛? Brannick et al. [12] showed that when 𝐴 and 𝑀 are Hermitian positive definite (HPD), the optimal interpolation is such that its range contains the 𝑛 𝑐 smallest generalized eigenvectors of the matrix pencil (𝐴, 𝑀). Recently, in Ali et al. [5] we generalized this framework to the non-HPD setting, by considering both right (interpolation) and left (restriction) generalized eigenvectors of (𝐴, 𝑀) and defining corresponding nonsymmetric transfer operators {𝑅#, 𝑃#}. Tight convergence bounds for {𝑅#, 𝑃#} are derived in spectral radius, as well as a proof of pseudo-optimality. Note, {𝑅#, 𝑃#} are typically complex valued, which is not practical for real-valued problems. Here, in this work, we build on [5], first characterizing all inner products in which the coarse-space correction defined by {𝑅#, 𝑃#} is orthogonal. We then develop tight two-level convergence bounds in these norms, and prove that the underlying transfer operators {𝑅#, 𝑃#} are genuinely optimal. As a special case, our theory both recovers and extends the HPD results from [12]. Finally, we show how to construct optimal, real-valued transfer operators in the case of that 𝐴 and 𝑀 are real valued, but are not HPD. Numerical examples arising from a discretized advection-reaction equation, wave-equation, and Stokes equations are used to verify and illustrate the theory.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2023

Temperature uncertainty modelling with proxy structural data as geostatistical constraints for well siting: an example applied to Granite Springs Valley, NV, USA

Utilizing existing temperature and structural geology information around Granite Springs Valley, Nevada, we build 3D stochastic temperature models with the aims of evaluating the 3D uncertainty of temperature and choosing between candidate exploration well locations. The data used to support the modelling are measured temperatures and structural proxies from 3D geologic modelling (distance to fault, distance to fault intersections and terminations, Coulomb stress change and dilation tendency), the latter considered ‘secondary’ data. Two stochastic geostatistical techniques are explored for incorporating the structural proxies: cosimulation and local varying mean. With both the cosimulation and local varying mean methods, many equally-likely temperature models (i.e. realizations) are produced, from which temperature probability profiles are calculated at candidate well locations. To aid in choosing between the candidate locations, two quantities summarize the temperature probabilities: V prior and entropy. V prior quantifies the likelihood for economic temperatures at each candidate location, whereas entropy identifies where new information has the most potential to reduce uncertainty. In general, the cosimulation realizations have smoother spatial structure, and extrapolate high temperatures at candidate locations that are located along the direction of the longest spatial correlation, which are down dip from existing temperature logs. The smooth realizations result in tight temperature probability profiles that are easier to interpret, but they have unrealistic temperature reversals in some locations because of the dipping ellipsoid shape created and that the cosimulation technique does not enforce a conductive geothermal gradient as a baseline (i.e. linearly increasing temperature with depth). The local varying mean results produce realizations with more realistic geothermal gradients, with temperatures increasing downward since a depth-temperature relationship is included. However, because they have much noisier spatial nature compared to cosimulation, it is harder to interpret the temperature probability profiles. The different local varying mean results allow the geologist to determine which proxy (e.g. dilation v. distance to fault termination) should be used given the specific geothermal system. In general, V prior from local varying mean results identify locations that are close to high values for the structural proxies: areas with higher probabilities for higher temperatures. The entropy results identify where uncertainty is greatest and therefore new drilling information could be most useful. Though these techniques provide useful information, even when applied to areas of sparse data, our comparison of these two techniques demonstrates the need for new geothermal geostatistics techniques that combine the advantages of these two methods and that are tailored to the spatial uncertainty issues inherent in geothermal exploration.

15 GEOTHERMAL ENERGY↗
DOE OSTI2021

Visualizing Vehicle Acceleration and Braking Energy at Intersections along a Major Traffic Corridor

Automobiles approaching a controlled intersection need to brake and come to a full stop when the signal transitions from green to red, and the vehicle must later accelerate to normal speeds after the signal changes back to green. These stops and starts associated with normal signal changes lead to unnecessary energy consumption and vehicle emissions. Previous studies have revealed that the optimization of traffic intersections' signal controls and coordination facilitates smoother traffic flows with reduced stop-and-go driving, which can significantly reduce traffic congestion and unnecessary fuel waste. This paper presents an interactive visual analytics dashboard that allows transportation planners to explore and analyze energy consumption patterns resulting from temporally varying traffic signal phases at multiple intersections along a major transportation corridor using traffic simulation outputs. The visual dashboard is implemented as an accessible and responsive web application and employs a combination of visualization techniques to cover multiple aspects of vehicle acceleration and braking at multiple adjacent intersections along a corridor. The paper presents a case study of a simulated traffic scenario on the Shallowford Road traffic corridor located in Chattanooga, Tennessee to demonstrate the capability of the visual dashboard.

Xu, Haowen↗
DOE OSTI2023

pnnl/mlxrd

A multi-task neural network for the simultaneous identification of multiple compounds from XRD data obtained in a synchrotron-based hydrothermal fluid system. To enhance the alignment between the training and test datasets, random noise is introduced into the synthetic training dataset, and minor labeled experimental data is incorporated. Additionally, we employ a weighted cross-entropy loss function to address data imbalances and ensure smoother model training.

Li, Ang↗
DOE OSTI2026

NCCS High Performance GMRES Mixed Precision

HPG-MxP is a software package that performs a fixed number of multigrid preconditioned (using a Gauss-Seidel smoother) Generalized minimal residual (PGMRES) iterations in order to solve a possibly nonsymmetric large sparse linear system of equations. It is designed to be a benchmark to measure a computer's performance for sparse linear algebra workloads typical in scientific computing while allowing the use of mixed precision methods. The solution is required to have convergence characteristics and accuracy similar to double precision GMRES. It is based on the High Performance Conjugate Gradient Benchmark (HPCG) which restricts all implementations to use only the IEEE double precision format (FP64). The original implementation (https://github.com/hpg-mxp/hpg-mxp) was written by Ichitaro Yamazaki, Jennifer Loe, Christian Glusa, Sivasankaran Rajamanickam, Piotr Luszczek, and Jack Dongarra. Please refer to that repository for documentation on the original implementation. This version is maintained by the National Center for Computational Sciences at Oak Ridge National Laboratory. It is highly scalable and optimized for Oak Ridge Leadership Computing Facility (OLCF) systems, particularly Frontier.

Kashi, Aditya [Oak Ridge National Laboratory (ORNL↗