Search NASA⌕ Search

SEARCH · Search NASA

Results for “solvent quality”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1995

A simulated RTM process for fabricating polyimide (AMB-21) carbon fiber composites

An experimental polyimide matrix, AMB-21 - supplied by NASA/LeRC, was especially formulated to be non-carcinogenic. It was also expected to be amenable to a Resin Transfer Molding Process (RTM). AMB-21 is a solid at room temperature and must be heated to a very high temperature to obtain a fluid state. However, even after heating it to a realistic high temperature, it was found to be too viscous for use in a RTM process. As a result, a promising approach was experimented leading to the introduction of the resin into a solvent solution in order to obtain a viscosity suitable for RTM. A mixture of methanol and tetrahydroferone was found to be a suitable solvent mixture. The matrix solution was introduced into carbon-fiber preform using two techniques: (1) injection of matrix into a Resin Transfer Mold after positioning the preform into the 'mold cavity', and (2) infiltration of matrix into the preform using the 'autoclave through-the-thickness transfer process'. After completing the resin transfer (infiltration) process, the 'filled' preform was heated to 300 F for one hour to reduce the solvent content. The temperature was then increased to 400 F under a vacuum to complete the solvent evaporation and to remove volatile products of the polyimide imidization. The impregnated preform was removed from the mold and press-cured at 200 psi and 600 FF for two hours. The resulting panel was found to be of reasonably good quality. This observation was based on the results obtained from short beam shear strength (700-8000 psi) tests and microscopic examination of the cross-section indicating a very low level of porosity. Further, the flash around the molded panels from the compression molding was free of porosity indicating the removal of volatiles, solvents, and other imidization products. Based on these studies, a new RTM mold containing a diaphragm capable of applying 200 psi at 600 F has been designed and constructed with the expectation that it will allow the incorporation of all of the above processing steps, including the consolidation with the preform in the mold cavity. Moreover, the new diaphragm design will enable to process larger preform panels. Processing studies with the diaphragm mold are being initiated.

Avva, V. Sarma↗
DOE OSTI2024

Environmental and economic analyses of chemical recycling via dissolution of waste polyethylene terephthalate

Globally, more than 1000 organizations and 175 nations are facing the plastic waste problem and have realized the need to transition from “linear-to-circular” economy of plastics. While the current mechanical recycling technologies for plastics are struggling to increase the U.S. plastic recycling rates beyond 9%, chemical recycling technologies become important complementary technologies to the predominant mechanical recycling that are needed to realize the circular economy in plastics supply chains. Dissolution is one such chemical recycling technology that can recycle waste plastic back into high-quality virgin grade plastic. However, the environmental and economic impacts of chemical recycling of waste polyethylene terephthalate (PET) via dissolution technology using a green solvent are unknown. Our study evaluated environmental metrics such as greenhouse gas (GHG) emissions and cumulative energy demand, and economic metrics such as net present value (NPV), minimum selling price, payback period, return on investment, and discounted internal rate of return for three dissolution processes with polymer recovery via anti-solvent, evaporation, and cooling precipitation techniques. The dissolution process with evaporation technique was the most economically favorable, whereas that with cooling technique was the most environmentally favorable. The anti-solvent approach had low economic performance and the highest environmental impacts. The NPV for all of these technologies ranged from $2.67 MM to $10.93 MM for a capacity of 8,400 MT/year and was found to be the highest for dissolution with evaporation approach and the least for anti-solvent approach. The cradle-to-gate GHG emissions and energy demand for PET dissolution processes ranged from 1.33-3.77 kg CO2-eq/kg of chemically recycled (CR) PET and18.9-56.1 MJ/kg of CR-PET, respectively. These economic and environmental metrics will be helpful in evaluating the sustainability of circular PET supply chains in the U.S.

09 BIOMASS FUELS↗
DOE OSTI2025

Controlled Synthesis of SnO 2 Nanocrystals with Tunable Band Gaps

Tin(IV) oxide nanocrystals (SnO 2 NCs) have significant potential in various applications, with their performance closely related to their band gap. The band gap is influenced by the size and shape of the NCs, which can be precisely controlled by adjusting reaction conditions. In this study, we present deliberately designed synthesis protocols to produce high-quality SnO 2 NCs with tunable band gaps using different methods. Key factors affecting the synthesis include control of the oxidizing agent, reaction temperature, solvent selection, and reaction time optimization. The resulting NCs were characterized by using TEM, XRD, XPS, and optical spectroscopy. Notably, SnO 2 NCs synthesized by controlling the oxidizing agent (air injection) in a hot organic solution were smaller in size and exhibited abundant oxygen vacancies. In contrast, extending the reaction time or using ethanol as a solvent in hydrothermal systems facilitated larger spherical or rod-like SnO 2 NCs with fewer oxygen vacancies. Further analysis of the band gap and valence band maximum energy revealed that the abundant vacancies in SnO 2 NCs synthesized with the air-controlled hot organic solution method resulted in a narrower band gap and an upshifted valence band. These synthetic strategies illustrate the potential for deliberately designing SnO 2 NCs with optimized electronic structures for various applications.

band gap↗
DOE OSTI2025

Influence of functional additives, fillers, and pigments on thermal and catalytic pyrolysis of polyethylene for waste plastic upcycling

Pyrolysis offers a relatively green and economical method to convert waste plastics into valuable chemicals and fuels without the need for harmful solvents, toxic chemicals, or costly high-pressure reactors. Despite its popularity among chemical upcycling technologies, industrial adoption suffers from feedstock heterogeneity, low-quality products, and catalyst deactivation. Most plastics in our daily lives are formulated with functional additives, fillers, and colorants. These additives remaining in end-of-life waste streams increase feedstock heterogeneity, creating a challenging issue in recycling plastics. Still, the potential impacts of additives on the chemical upcycling of plastics have been poorly understood. In this study, polyethylene compounded with a range of widely used additives (antioxidants, stabilizers, pigments, fillers, slip agents, and flame retardants) was subjected to both thermal pyrolysis and catalytic pyrolysis in different catalyst-to-feedstock contact modes. It showed that many inorganic additives, such as talc, kaolin, CaCO 3 , TiO 2 , carbon black, and zinc stearate, facilitated polymer decomposition during pyrolysis, increasing light hydrocarbons while also promoting aromatic and carbon residue formation. Conversely, antioxidants and stabilizers inhibited depolymerization, favoring heavier hydrocarbons. During catalytic pyrolysis with HZSM-5 zeolite, additives strongly enhanced aromatic and catalytic coke formation, especially when there was direct contact between plastics and catalysts. Although certain additives seem beneficial in the short term by promoting polymer cracking and improving the selectivity of aromatics, the transport of the additives and their degradation products and increased carbon coking can contaminate products, deactivate or modify catalysts, and foul reactors. These findings address a critical knowledge gap in effectively converting waste plastics via a greener route.

42 ENGINEERING↗
NASA NTRS1988

Controlling Vapor Pressure In Hanging-Drop Crystallization

Rate of evaporation adjusted to produce larger crystals. Device helps to control vapor pressure of water and other solvents in vicinity of hanging drop of solution containing dissolved enzyme protein. Well of porous frit (sintered glass) holds solution in proximity to drop of solution containing protein or enzyme. Vapor from solution in frit controls evaporation of solvent from drop to control precipitation of protein or enzyme. With device, rate of nucleation limited to decrease number and increase size (and perhaps quality) of crystals - large crystals of higher quality needed for x-ray diffraction studies of macromolecules.

Carter, Daniel C.↗
NASA NTRS2001

Improved Detection Technique for Solvent Rinse Cleanliness Verification

The NASA White Sands Test Facility (WSTF) has an ongoing effort to reduce or eliminate usage of cleaning solvents such as CFC-113 and its replacements. These solvents are used in the final clean and cleanliness verification processes for flight and ground support hardware, especially for oxygen systems where organic contaminants can pose an ignition hazard. For the final cleanliness verification in the standard process, the equivalent of one square foot of surface area of parts is rinsed with the solvent, and the final 100 mL of the rinse is captured. The amount of nonvolatile residue (NVR) in the solvent is determined by weight after the evaporation of the solvent. An improved process of sampling this rinse, developed at WSTF, requires evaporation of less than 2 mL of the solvent to make the cleanliness verification. Small amounts of the solvent are evaporated in a clean stainless steel cup, and the cleanliness of the stainless steel cup is measured using a commercially available surface quality monitor. The effectiveness of this new cleanliness verification technique was compared to the accepted NVR sampling procedures. Testing with known contaminants in solution, such as hydraulic fluid, fluorinated lubricants, and cutting and lubricating oils, was performed to establish a correlation between amount in solution and the process response. This report presents the approach and results and discusses the issues in establishing the surface quality monitor-based cleanliness verification.

Hornung, S. D.↗
NASA NTRS2006

Automated Solvent Seaming of Large Polyimide Membranes

A solvent-based welding process enables the joining of precise, cast polyimide membranes at their edges to form larger precise membranes. The process creates a homogeneous, optical-quality seam between abutting membranes, with no overlap and with only a very localized area of figure disturbance. The seam retains 90 percent of the strength of the parent material. The process was developed for original use in the fabrication of wide-aperture membrane optics, with areal densities of less than 1 kg/m2, for lightweight telescopes, solar concentrators, antennas, and the like to be deployed in outer space. The process is just as well applicable to the fabrication of large precise polyimide membranes for flat or inflatable solar concentrators and antenna reflectors for terrestrial applications. The process is applicable to cast membranes made of CP1 (or equivalent) polyimide. The process begins with the precise fitting together and fixturing of two membrane segments. The seam is formed by applying a metered amount of a doped solution of the same polyimide along the abutting edges of the membrane segments. After the solution has been applied, the fixtured films are allowed to dry and are then cured by convective heating. The weld material is the same as the parent material, so that what is formed is a homogeneous, strong joint that is almost indistinguishable from the parent material. The success of the process is highly dependent on formulation of the seaming solution from the correct proportion of the polyimide in a suitable solvent. In addition, the formation of reliable seams depends on the deposition of a precise amount of the seaming solution along the seam line. To ensure the required precision, deposition is performed by use of an automated apparatus comprising a modified commercially available, large-format, ink-jet print head on an automated positioning table. The printing head jets the seaming solution into the seam area at a rate controlled in coordination with the movement of the positioning table.

Rood, Robert↗
DOE OSTI2025

Scalable mechanochemical synthesis of high-quality Prussian blue analogues for high-energy and durable potassium-ion batteries

Prussian blue analogues (PBAs) are recognized as promising cathode materials for potassium-ion batteries (PIBs), particularly the low-cost and high-energy K 2 Mn[Fe(CN) 6 ](KMnF). However, conventional solution-based synthesis inevitably introduces [Fe(CN) 6 ] 4− defects and lattice water while suffering low synthesis efficiency, unfavorable to the improvement of electrochemical performance and scalability. Here, in this work, we report a simple solvent-free mechanochemical strategy for the synthesis of a wide variety of K 2 M[Fe(CN) 6 ] (M = Mn, Mg, Ca, etc.) with negligible defects and water, and it is unprecedented to achieve kilogram-level products of high-quality KMnF within just 10 minutes. The as-prepared KMnF delivers a high energy density of 590 Wh kg −1 at 0.2 C and exhibits an astonishing stability over 10 000 cycles and rate ability up to 50 C in a potassium metal half-cell. Encouragingly, a high-areal-capacity pouch cell with 2.2 mAh cm −2 (16.5 mg cm −2 ) exhibits a capacity retention of 80.7% after 500 cycles. Furthermore, systematic in situ characterization reveals underlying mechanism insights into structure–performance relationships. Specifically, the fully coordinated Mn–N 6 octahedral configuration effectively suppresses Mn 3+ Jahn–Teller distortion, enabling reversible phase transitions under both high-voltage and long-term cycling conditions. In addition, minimal defects provide sufficient redox centers, while the continuous three-dimensional framework facilitates rapid K + diffusion kinetics. This work provides a new opportunity for the ultrafast, universal and scalable synthesis of high-quality PBAs, facilitating the practical application of PIBs while enabling precise structural and compositional design of novel PBAs.

Mechanochemical method↗
NASA NTRS1999

Solidification of II-VI Compounds in a Rotating Magnetic Field

This project is aimed at using a rotating magnetic field (RMF) to control fluid flow and transport during directional solidification of elemental and compound melts. Microgravity experiments have demonstrated that small amounts of residual acceleration of less than a micro-g can initiate and prolong fluid flow, particularly when there is a static component of the field perpendicular to the liquid solid interface. Thus a true diffusion boundary layer is not formed, and it becomes difficult to verify theories of solidification or to achieve diffusion controlled solidification. The RMF superimposes a stirring effect on an electrically conducting liquid, and with appropriate field strengths and frequencies, controlled transport of material through a liquid column can be obtained. As diffusion conditions are precluded and complete mixing conditions prevail, the technique is appropriate for traveling solvent zone or float zone growth methods in which the overall composition of the liquid can be maintained throughout the growth experiment. Crystals grown by RMF techniques in microgravity in previous, unrelated missions have shown exceptional properties. The objective of the project is two-fold, namely (1) using numerical modeling to simulate the behavior of a solvent zone with applied thermal boundary conditions and demonstrate the effects of decreasing gravity levels, or an increasing applied RMF, or both, and (2) to grow elements and II-VI compounds from traveling solvent zones both with and without applied RMFs, and to determine objectively how well the modeling predicts solidification parameters. Numerical modeling has demonstrated that, in the growth of CdTe from a tellurium solution, a rotating magnetic field can advantageously modify the shape of the liquid solid interface such that the interface is convex as seen from the liquid. Under such circumstances, the defect structure is reduced as any defects which are formed tend to grow out and not propagate. The flow of liquid, however, is complex due to the competing flow induced by the rotating magnetic field and the buoyancy driven convection. When the acceleration forces are reduced to one thousandth of gravity, the flow pattern is much simplified and well controlled material transport through the solvent zone can be readily achieved. Triple axis diffractometry and x-ray synchrotron topography have demonstrated that there is no significant improvement in crystal quality for HgCdTe grown on earth from a tellurium solution when a rotating magnetic field is applied. However, modeling shows that the flow in microgravity with a rotating magnetic field would produce a superior product.

Gillies, D. C.↗
NASA NTRS2001

Films, Preimpregnated Tapes and Composites Made from Polyimide "Salt-Like" Solutions

High quality films, preimpregnated tape (prepegs), and composites have been fabricated from polyimide precursor 'saltlike' solutions. These salt-like solutions have a low viscosity (5,000 to 10,000 cp) and a high solids content (50-65% by weight) and can be coated onto reinforcing fiber to produce prepegs with excellent tack and drape at 12-15% residual solvent (approximately 4-6% water from thermal imidization reaction). The processing of these types of prepegs significantly overcomes solvent removal problems and allows excellent fiber wet out. In addition, the physical characteristics of the polyimide precursor salt-like solutions permits processing into high-performance materials through the use of standard prepregging and composite fabrication equipment. The resultant composites are of high quality.

Cano, Roberto J.↗
NASA NTRS1987

Non-conventional approaches to food processing in CELSS. I - Algal proteins: Characterization and process optimization

Protein isolate obtained from green algae (Scenedesmus obliquus) cultivated under controlled conditions was characterized. Molecular weight determination of fractionated algal proteins using SDS-polyacrylamide gel electrophoresis revealed a wide spectrum of molecular weights ranging from 15,000 to 220,000. Isoelectric points of dissociated proteins were in the range of 3.95 to 6.20. Amino acid composition of protein isolate compared favorably with FAO standards. High content of essential amino acids leucine, valine, phenylalanine and lysine makes algal protein isolate a high quality component of CELSS diets. To optimize the removal of algal lipids and pigments supercritical carbon dioxide extraction (with and without ethanol as a co-solvent) was used. Addition of ethanol to supercritical CO2 resulted in more efficient removal of algal lipids and produced protein isolate with a good yield and protein recovery. The protein isolate extracted by the above mixture had an improved water solubility.

Nakhost, Z.↗
DOE OSTI2024

Tackling P3HT:Y‐Series Miscibility Through Advanced Processing for Tunable Aggregation

Abstract Polymer and small molecule blend thin films are of strong interest for organic electronics and particularly organic solar cells. The high miscibility in blends of ordinary P3HT and state‐of‐the‐art Y‐series non‐fullerene acceptors (NFAs) suppresses phase separation and aggregation challenging successful charge separation and transport. In a recent work, current‐induced doping (CID) is introduced, a method to precisely control the aggregation of Poly(3‐hexylthiophene) (P3HT) in solution. The highly ordered pre‐aggregation in solution is used here to control the P3HT aggregation in neat films and blends with Y12 (BTP‐4F‐12). This results in a 25‐fold increase in hole mobility in P3HT organic field‐effect transistor (OFET) devices and tunability of the P3HT aggregate quality in the presence of Y12 over large ranges. At the same time, particularly the Y12 long‐range ordering is heavily suppressed by increasing P3HT aggregation. However, solvent vapor annealing (SVA) leads to an extraordinarily high Y12 ordering, changes in the crystal orientation of Y12, and a further improvement of P3HT aggregation. A broad range of different degrees of aggregation of both materials can therefore be obtained in the final thin films solely by changing processing parameters without changing the composition of the material system.

Chemistry↗
DOE OSTI2022

On the optimized 3D printing and post-processing of PETG materials

Glycol-modified polyethylene terephthalate (PETG) is a reliable middle ground between polylactic acid and acrylonitrile butadiene styrene due to its light weight, impact resistance, toughness, flexibility, and cost-effectiveness. However, during 3D printing, the filament form is prone to oozing and stringing. In this study, we optimized the PETG printability via g-code setting and printing parameter modification, and consideration of filament quality, build plate temperature and leveling, and printing design complexity. Printed PETGs were thermally and chemically annealed, and post-processing conditions including annealing time, temperature, and solvent use were investigated. Mechanical properties were evaluated in terms of print parameter changes and post-processing techniques.

36 MATERIALS SCIENCE↗
NASA NTRS2000

Fluid Physics and Macromolecular Crystal Growth in Microgravity

The first protein crystallization experiment in microgravity was launched in April, 1981 and used Germany's Technologische Experimente unter Schwerelosigkeit (TEXUS 3) sounding rocket. The protein P-galactosidase (molecular weight 465Kda) was chosen as the sample with a liquid-liquid diffusion growth method. A sliding device brought the protein, buffer and salt solution into contact when microgravity was reached. The sounding rocket gave six minutes of microgravity time with a cine camera and schlieren optics used to monitor the experiment, a single growth cell. In microgravity a strictly laminar diffusion process was observed in contrast to the turbulent convection seen on the ground. Several single crystals, approx 100micron in length, were formed in the flight which were of inferior but of comparable visual quality to those grown on the ground over several days. A second experiment using the same protocol but with solutions cooled to -8C (kept liquid with glycerol antifreeze) again showed laminar diffusion. The science of macromolecular structural crystallography involves crystallization of the macromolecule followed by use of the crystal for X-ray diffraction experiments to determine the three dimensional structure of the macromolecule. Neutron protein crystallography is employed for elucidation of H/D exchange and for improved definition of the bound solvent (D20). The structural information enables an understanding of how the molecule functions with important potential for rational drug design, improved efficiency of industrial enzymes and agricultural chemical development. The removal of turbulent convection and sedimentation in microgravity, and the assumption that higher quality crystals will be produced, has given rise to the growing number of crystallization experiments now flown. Many experiments can be flown in a small volume with simple, largely automated, equipment - an ideal combination for a microgravity experiment. The term "protein crystal growth" is often historically used to describe these microgravity experiments. This is somewhat inaccurate as the field involves the study of many varied biological molecules including viruses, proteins, DNA, RNA and complexes of those structures. For this reason we use the term macromolecular crystal growth. In this chapter we review a series of diagnostic microgravity crystal growth experiments carried out principally using the European Space Agency (ESA) Advanced Protein Crystallization Facility (APCF). We also review related research, both experimental and theoretical, on the aspects of microgravity fluid physics that affect microgravity protein crystal growth. Our experiments have revealed some surprises that were not initially expected. We discuss them here in the context of practical lessons learnt and how to maximize the limited microgravity opportunities available.

Helliwell, John R.↗
DOE OSTI2023

Large-scale computational polymer solubility predictions and applications to dissolution-based plastic recycling

Dissolution-based plastic recycling is a promising approach to separate and recover high quality pure polymer resins from multicomponent plastic waste by exploiting differences in polymer solubility. The design of a dissolution-based polymer recycling process requires the selection of appropriate solvent systems and operating temperatures to dissolve only target polymers. Determining these parameters experimentally is challenging due to the wide range of solvents and temperatures possible for a given set of target polymers. In this work, we report a computational scheme that employs molecular dynamics simulations and the Conductor-like Screening Model for Realistic Solvents to predict polymer solubilities. Using this scheme, we established a computational solubility database for 8 common polymers and 1007 solvents at multiple temperatures and measured selected solubilities experimentally to validate computational predictions. Analysis of functional groups within this large database then provides chemical heuristics relating the molecular structures of good and non-solvents for selected polymers. We further developed a tool that automates the selection of solvents for all possible sequences in which target polymers can be selectively dissolved to guide the design of dissolution-based plastic recycling processes. Here, we demonstrate the application of these methods via multiple experimental case studies of representative dissolution-based polymer recycling processes in which pure polymer resins were successfully recovered from physical mixtures of polymers.

42 ENGINEERING↗
NASA NTRS1995

QFD analysis of RSRM aqueous cleaners

This paper presents a Quality Function Deployment (QFD) analysis of the final down-selected aqueous cleaners to be used on the Redesigned Solid Rocket Motor (RSRM) program. The new cleaner will replace solvent vapor degreasing. The RSRM Ozone Depleting Compound Elimination program is discontinuing the methyl chloroform vapor degreasing process and replacing it with a spray-in-air aqueous cleaning process. Previously, 15 cleaners were down-selected to two candidates by passing screening tests involving toxicity, flammability, cleaning efficiency, contaminant solubility, corrosion potential, cost, and bond strength. The two down-selected cleaners were further evaluated with more intensive testing and evaluated using QFD techniques to assess suitability for cleaning RSRM case and nozzle surfaces in preparation for adhesive bonding.

Marrs, Roy D.↗
NASA NTRS2024

Xplo-SA9T: Optimization of Sorbent Technology With Existing and New Amine Variants for Carbon Dioxide Removal and Humidity Control

Scrubbing of the spacesuit air stream to control humidity and regulate carbon dioxide (CO 2 ) relies on amine-loaded resins, colloquially known as sorbents. The efficacy of Rapid Cycle Amine technology relies on the propensity of nitrogens toward adsorption of CO 2 while simultaneously offering regenerative properties under vacuum or positive pressure. The commonly utilized sorbent, SA9T, was recreated and evaluated further to increase stability and serve as a benchmark comparison for newly synthesized amine sorbent technologies. Ongoing storage studies with eight different environments will allow the development of applicable storage protocols and provide insight into possible ammonia generation pathways. Attempts to alleviate the known issues with SA9T included the alteration of the primary amine (tetraethylenepentamine), the choice of resin, and the particle size distribution. In-house CO 2 breakthrough experiments were conducted using a specialized apparatus that can simulate spacesuit conditions, offering high-quality triplicate capacity analysis affording direct comparison to known adsorbents in the literature. Thermo-Desorption Gas Chromatography Mass Spectrometry studies on the synthesized materials revealed any reagent or solvent offgassing while Nuclear Magnetic Resonance spectroscopy tracked the stability of the bound amine. Scanning Electron Microscope images of sieved materials provided a more accurate size interpretation facilitating synthetic design and pressure drop elimination. All efficient sorbents were synthesized to a commercial batch scale subsequent to evaluation including Xplo-SA9T.

John R Tidwell↗