Results for “stream processing” — Page 6

NASA NTRS2010

A Data Filter for Identifying Steady-State Operating Points in Engine Flight Data for Condition Monitoring Applications

This paper presents an algorithm that automatically identifies and extracts steady-state engine operating points from engine flight data. It calculates the mean and standard deviation of select parameters contained in the incoming flight data stream. If the standard deviation of the data falls below defined constraints, the engine is assumed to be at a steady-state operating point, and the mean measurement data at that point are archived for subsequent condition monitoring purposes. The fundamental design of the steady-state data filter is completely generic and applicable for any dynamic system. Additional domain-specific logic constraints are applied to reduce data outliers and variance within the collected steady-state data. The filter is designed for on-line real-time processing of streaming data as opposed to post-processing of the data in batch mode. Results of applying the steady-state data filter to recorded helicopter engine flight data are shown, demonstrating its utility for engine condition monitoring applications.

Simon, Donald L.↗

NASA NTRS1975

Application of the theory of jet stream to the asteroidal belt

The possibility of incorporating the resonant effect and jet stream formation process into the problems of the Hilda asteroids and Kirkwood gaps is discussed qualitatively. It appears that formation of the precursor jet streams of the resonant asteroids in the main belt would be suppressed due to the collisional perturbation effect of the ambient matter in this region. Together with the biased distribution of near-resonant asteroids, the depletion across the Kirkwood gaps could be understood. Within the context of jet stream theory the existence of Hilda asteroids outside the main belt requires the original limit of the main belt to be not much more extensive than the present value of 3.5 AU. This is suggestive of a cosmogonic origin of the observed outer limit.

Ip, W.-H.↗

NASA NTRS1989

AFTI/F-111 airplane mission adaptive wing operational flight evaluation technique using uplinked pilot command cues

NASA and the USAF have conducted a program to investigate aircraft performance improvements utilizing a mission adaptive wing (MAW). The MAW was designed and developed for the AFTI/F-111 variable-sweep aircraft to provide a hydraulically driven, smooth, and continuous variable camber of the trailing and leading edges as a function of maneuvering requirements or of flight conditions. The remotely augmented vehicle facility (RAV) at the NASA DFRF, as utilized in the MAW investigations, is described. The RAV was a dedicated, ground based, general purpose facility capable of receiving a data stream downlinked from a test vehicle, processing this data stream in a digital computer, and transmitting processed data back to the test vehicle. It is shown that this method of flight testing provides a technique that can evaluate highly dynamic maneuvers.

Kempel, Robert W.↗

NASA NTRSDate not supplied

A System to Provide Deterministic Flight Software Operation and Maximize Multicore Processing Performance: The Safe and Precise Landing – Integrated Capabilities Evolution (SPLICE) Datapath

A method and design are described for a system that processes multiple data streams, utilizing a multicore asymmetric processing architecture, that eliminates data interrupts to the application processors. The design supports a deterministic environment for flight software in NASA’s Safe and Precise Landing – Integrated Capabilities Evolution (SPLICE) project. The SPLICE project develops sensor, algorithm, and compute technologies for Precision Landing and Hazard Avoidance (PL&HA) capabilities. The compute technology for SPLICE is the Descent and Landing Computer (DLC). The DLC hosts several SPLICE algorithms with high computational resource requirements that must be executed in a real-time and deterministic manner. The software runs on a custom Single Board Computer (SBC), with a Xilinx Ultrascale+ Multiprocessor System-on-a-Chip (MPSoC). Input data for the flight software is from a variety of sensors, unique with respect to data rate and packet size. A data path between the SPLICE sensors and algorithms is designed to efficiently deliver this data to the flight software using the MPSoC asymmetric processing cores and Field Programmable Gate Array (FPGA) fabric. This is implemented in a manner that isolates the application processors running the flight software from interrupts associated with the input data. By leveraging real-time processors on the MPSoC, and a structure with the appropriate interfaces in the shared memory on the SBC, the flight software can use the full set of application processors. The available utilization for each processor in this set is also maximized for the SPLICE applications, providing a sufficiently deterministic execution environment without the cost and overhead of a real-time operating system.

heterogeneous processing system↗

NASA NTRS2023

A System to Provide Deterministic Flight Software Operation and Maximize Multicore Processing Performance: The Safe and Precise Landing – Integrated Capabilities Evolution (SPLICE) Datapath

A method and design are described for a system that processes multiple data streams, utilizing a multicore asymmetric processing architecture, that eliminates data interrupts to the application processors. The design supports a deterministic environment for flight software in NASA’s Safe and Precise Landing – Integrated Capabilities Evolution (SPLICE) project. The SPLICE project develops sensor, algorithm, and compute technologies for Precision Landing and Hazard Avoidance (PL&HA) capabilities. The compute technology for SPLICE is the Descent and Landing Computer (DLC). The DLC hosts several SPLICE algorithms with high computational resource requirements that must be executed in a real-time and deterministic manner. The software runs on a custom Single Board Computer (SBC), with a Xilinx Ultrascale+ Multiprocessor System-on-a-Chip (MPSoC). Input data for the flight software is from a variety of sensors, unique with respect to data rate and packet size. A data path between the SPLICE sensors and algorithms is designed to efficiently deliver this data to the flight software using the MPSoC asymmetric processing cores and Field Programmable Gate Array (FPGA) fabric. This is implemented in a manner that isolates the application processors running the flight software from interrupts associated with the input data. By leveraging real-time processors on the MPSoC, and a structure with the appropriate interfaces in the shared memory on the SBC, the flight software can use the full set of application processors. The available utilization for each processor in this set is also maximized for the SPLICE applications, providing a sufficiently deterministic execution environment without the cost and overhead of a real-time operating system.

David K. Rutishauser↗

NASA NTRS1973

Application of ERTS-1 imagery to detecting and mapping modern erosion features, and to monitoring erosional changes, in southern Arizona

The author has identified the following significant results. ERTS-1 multispectral images have been used, without additional data, to prepare three maps at 1:1 million scale of the 18,000 sq. mi. project area: (1) modern (post-1890 A. D.) arroyos and channels; (2) types of stream channels; and (3) potential erodibility of soils; surficial deposits, and bedrock. Also completed was the collection and compilation of ground truth geologic, soil, and hydrologic data. Field studies to obtain ground control for the photointerpretive mapping include: (1) measurements, at many sites, of the depth, width, and channel characteristics of arroyos and gullies, and cross profiles of stream channels, flood plains, and Holocene terraces; and (2) stratigraphic measurements of the Holocene alluvial deposits. Significant conclusions from these extensive stratigraphic studies are: Slow deposition of sediment was the dominant process on stream lowlands throughout the project area for at least 2000 years prior to 1890 A.D. The deposition was broken by only two relatively brief and minor erosional episodes of regional importance, when channels no more than a third of the depth of modern channels were cut. The modern erosion has produced within about 80 years substantially more and larger arroyos than any erosion episode during the last 2000 years, and the end is not in sight.

Morrison, R. B.↗

NASA NTRS1985

Liquid droplet radiator program at the NASA Lewis Research Center

The NASA Lewis Research Center and the Air Force Rocket Propulsion Laboratory (AFRPL) are jointly engaged in a program for technical assessment of the Liquid Droplet Radiator (LDR) concept as an advanced high performance heat ejection component for future space missions. NASA Lewis has responsibility for the technology needed for the droplet generator, for working fluid qualification, and for investigating the physics of droplets in space; NASA Lewis is also conducting systems/mission analyses for potential LDR applications with candidate space power systems. For the droplet generator technology task, both micro-orifice fabrication techniques and droplet stream formation processes have been experimentally investigated. High quality micro-orifices (to 50 micron diameter) are routinely fabricated with automated equipment. Droplet formation studies have established operating boundaries for the generation of controlled and uniform droplet streams. A test rig is currently being installed for the experimental verification, under simulated space conditions, of droplet radiation heat transfer performance analyses and the determination of the effect radiative emissivity of multiple droplet streams. Initial testing has begun in the NASA Lewis Zero-Gravity Facility for investigating droplet stream behavior in microgravity conditions. This includes the effect of orifice wetting on jet dynamics and droplet formation. Results for both Brayton and Stirling power cycles have identified favorable mass and size comparisons of the LDR with conventional radiator concepts.

Presler, A. F.↗

NASA NTRS1986

Liquid droplet radiator program at the NASA Lewis Research Center

The NASA Lewis Research Center and the Air Force Rocket Propulsion Laboratory (AFRPL) are jointly engaged in a program for technical assessment of the Liquid Droplet Radiator (LDR) concept as an advanced high performance heat ejection component for future space missions. NASA Lewis has responsibility for the technology needed for the droplet generator, for working fluid qualification, and for investigating the physics of droplets in space; NASA Lewis is also conducting systems/mission analyses for potential LDR applications with candidate space power systems. For the droplet generator technology task, both micro-orifice fabrication techniques and droplet stream formation processes have been experimentally investigated. High quality micro-orifices (to 50 micron diameter) are routinely fabricated with automated equipment. Droplet formation studies have established operating boundaries for the generation of controlled and uniform droplet streams. A test rig is currently being installed for the experimental verification, under simulated space conditions, of droplet radiation heat transfer performance analyses and the determination of the effect radiative emissivity of multiple droplet streams. Initial testing has begun in the NASA Lewis Zero-Gravity Facility for investigating droplet stream behavior in microgravity conditions. This includes the effect of orifice wetting on jet dynamics and droplet formation. Results for both Brayton and Stirling power cycles have identified favorable mass and size comparisons of the LDR with conventional radiator concepts.

Presler, A. F.↗

DOE OSTI2025

Challenges in Product Selectivity for Electrocatalytic Reduction of Amine-Captured CO 2 : Implications for Reactive Carbon Capture

CO 2 is a potential feedstock for carbon-based fuels or materials, but is only available in dilute streams. Integrated processes for CO 2 capture and conversion directly valorize the CO 2 captured by sorbent materials, skipping the energetically expensive sorbent regeneration step. Amines are the most heavily studied liquid-phase sorbent materials for CO 2 capture from dilute streams. Amines react with CO 2 in a 2:1 ratio to form the corresponding ammonium carbamate. Ammonium carbamate [NH 4 ][H 2 NCO 2 ] was tested as the substrate using the highly selective and robust CO 2 -to-formate reduction electrocatalyst [( tBu POCOP)Ir(H)(NCCH 3 ) 2 ], where ( tBu POCOP) is the tridentate pincer ligand 2,6-bis(di tert -butyl-phosphonito). When ammonium carbamate was used as the substrate instead of CO 2 , only hydrogen was produced. An equivalent electrolysis with ammonium hexafluorophosphate with CO 2 also resulted in primarily hydrogen. Methyl carbamate and urea were also tested as substrates as proxies for carbamate that do not contain an equivalent of ammonium, and there was also negligible reduction to carbon-based products. These results indicate that the loss of selectivity observed for aminecaptured CO 2 , or ammonium carbamate, is likely due to the generation of the acidic ammonium equivalent as well as the greater challenge of reducing carbamate compared to CO 2 . This study illustrates that catalysts with high selectivity for concentrated CO 2 can favor hydrogen evolution and loss of carbon-based products when amine-captured CO 2 is used instead.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NASA NTRS1977

Removal of contaminant gases from an electrolytic urine pretreatment process

The effluent gas stream from an electrolytic urine pretreatment process was analyzed by gas chromatography-mass spectroscopy and wet chemical methods to determine its composition. The major constituents were identified as: hydrogen, carbon dioxide, oxygen, nitrogen, water vapor, and chlorine. The trace impurities were chlorinated light hydrocarbons, and a number of other organic impurities in the low ppm range. Several methods of removing all of the undesirable gases to levels acceptable for return to a space cabin atmosphere were investigated experimentally. A subsystem concept comprised of the following sequential unit processes and operations was successfully demonstrated: (1) raw urine scrubbing, (2) silica gel sorption, (3) dilution with cabin air, and (4) catalytic oxidation.

Colombo, G. V.↗

DOE OSTI2026

Process design for recovering rare-earth elements from mine tailings with low rare-earth concentrations via sequential leaching and solvent extraction

Rare earth elements (REEs) are essential for advanced technologies and yet face significant supply chain risks due to their concentrated global production and limited domestic availability. Addressing this challenge requires efficient processes capable of upgrading low-grade secondary resources such as mine tailings. In this study, we developed a novel separation flowsheet that integrates sequential leaching and 2-stage solvent extraction (SX) processes to recover high-purity heavy REEs (HREEs) and light REEs (LREEs) from a simulated mine-tailing concentrate containing 2.4 wt% total REEs (TREEs; 0.6 wt% LREEs and 1.8 wt% HREEs). Sequential leaching with controlled pH adjustment selectively precipitated REEs while retaining the large amount of impurities in the solution, producing an REE-enriched leachate by following leaching processes with roughly twice the REE concentration and half the impurity concentration compared to that of single-step leaching. The optimized SX flowsheet employed Cyanex 572 to extract HREEs and Fe over LREEs, followed by Fe removal using tributyl phosphate (TBP), while the raffinate stream was processed by SX with di(2-ethylhexyl)phosphoric acid (D2EHPA) to recover LREEs under optimized conditions balancing both extraction efficiency and purity. Although increased extractant availability in the organic phase improved LREE recovery, it also increased co-extraction of Ca, underscoring trade-offs in process optimization. Both HREE- and LREE-rich solutions were subsequently precipitated into solid products via oxalate precipitation, resulting in high-purity REE solids containing ∼92.0 wt% HREEs (∼95.7 wt% TREEs) and ∼92.8 wt% LREEs (∼94.0 wt% TREEs). In conclusion, this proof-of-concept study using simulated mine tailings demonstrates a promising approach for upgrading low-grade REE resources, while highlighting the need for future validation with real materials.

Mine tailings↗

NASA NTRS2013

Lunar Sulfur Capture System

The Lunar Sulfur Capture System (LSCS) protects in situ resource utilization (ISRU) hardware from corrosion, and reduces contaminant levels in water condensed for electrolysis. The LSCS uses a lunar soil sorbent to trap over 98 percent of sulfur gases and about two-thirds of halide gases evolved during hydrogen reduction of lunar soils. LSCS soil sorbent is based on lunar minerals containing iron and calcium compounds that trap sulfur and halide gas contaminants in a fixed-bed reactor held at temperatures between 250 and 400 C, allowing moisture produced during reduction to pass through in vapor phase. Small amounts of Earth-based polishing sorbents consisting of zinc oxide and sodium aluminate are used to reduce contaminant concentrations to one ppm or less. The preferred LSCS configuration employs lunar soil beneficiation to boost concentrations of reactive sorbent minerals. Lunar soils contain sulfur in concentrations of about 0.1 percent, and halogen compounds including chlorine and fluorine in concentrations of about 0.01 percent. These contaminants are released as gases such as H2S, COS, CS2,HCl, and HF during thermal ISRU processing with hydrogen or other reducing gases. Removal of contaminant gases is required during ISRU processing to prevent hardware corrosion, electrolyzer damage, and catalyst poisoning. The use of Earth-supplied, single-use consumables to entirely remove contaminants at the levels existing in lunar soils would make many ISRU processes unattractive due to the large mass of consumables relative to the mass of oxygen produced. The LSCS concept of using a primary sorbent prepared from lunar soil was identified as a method by which the majority of contaminants could be removed from process gas streams, thereby substantially reducing the required mass of Earth-supplied consumables. The LSCS takes advantage of minerals containing iron and calcium compounds that are present in lunar soil to trap sulfur and halide gases in a fixedbed reactor downstream of an in-ISRU process such as hydrogen reduction. The lunar-soil-sorbent trap is held at a temperature significantly lower than the operating temperature of the hydrogen reduction or other ISRU process in order to maximize capture of contaminants, but is held at a high enough temperature to allow moisture to pass through without condensing. The lunar soil benefits from physical beneficiation to remove ultrafine particles (to reduce pressure drop through a fixed bed reactor) and to upgrade concentrations of iron and/or calcium compounds (to improve reactivity with gaseous contaminants).

Berggren, Mark↗

NASA NTRS2003

Web Audio/Video Streaming Tool

In order to promote NASA-wide educational outreach program to educate and inform the public of space exploration, NASA, at Kennedy Space Center, is seeking efficient ways to add more contents to the web by streaming audio/video files. This project proposes a high level overview of a framework for the creation, management, and scheduling of audio/video assets over the web. To support short-term goals, the prototype of a web-based tool is designed and demonstrated to automate the process of streaming audio/video files. The tool provides web-enabled users interfaces to manage video assets, create publishable schedules of video assets for streaming, and schedule the streaming events. These operations are performed on user-defined and system-derived metadata of audio/video assets stored in a relational database while the assets reside on separate repository. The prototype tool is designed using ColdFusion 5.0.

Guruvadoo, Eranna K.↗

NASA NTRS1986

Solar wind proton temperature-velocity relationship

Helios 1 data are analyzed to find an experimental fit for the temperature-velocity relationship at 1 AU. It is shown that the proton temperature-velocity changes at a velocity of approximately 500 km/s. Interplanetary dynamic processes, i.e., stream interactions, are shown to affect the temperature-velocity relationships less than 22 percent; the functional form of these relationships appears to be preserved throughout the solar cycle. It is pointed out that any comprehensive model of the solar wind will have to address the difference in the temperature-velocity relationship between the low- and high-speed wind, since this is a product of the acceleration and subsequent heating process generating the solar wind.

Lopez, R. E.↗

NASA NTRS2005

Portable Airborne Laser System Measures Forest-Canopy Height

(PALS) is a combination of laser ranging, video imaging, positioning, and data-processing subsystems designed for measuring the heights of forest canopies along linear transects from tens to thousands of kilometers long. Unlike prior laser ranging systems designed to serve the same purpose, the PALS is not restricted to use aboard a single aircraft of a specific type: the PALS fits into two large suitcases that can be carried to any convenient location, and the PALS can be installed in almost any local aircraft for hire, thereby making it possible to sample remote forests at relatively low cost. The initial cost and the cost of repairing the PALS are also lower because the PALS hardware consists mostly of commercial off-the-shelf (COTS) units that can easily be replaced in the field. The COTS units include a laser ranging transceiver, a charge-coupled-device camera that images the laser-illuminated targets, a differential Global Positioning System (dGPS) receiver capable of operation within the Wide Area Augmentation System, a video titler, a video cassette recorder (VCR), and a laptop computer equipped with two serial ports. The VCR and computer are powered by batteries; the other units are powered at 12 VDC from the 28-VDC aircraft power system via a low-pass filter and a voltage converter. The dGPS receiver feeds location and time data, at an update rate of 0.5 Hz, to the video titler and the computer. The laser ranging transceiver, operating at a sampling rate of 2 kHz, feeds its serial range and amplitude data stream to the computer. The analog video signal from the CCD camera is fed into the video titler wherein the signal is annotated with position and time information. The titler then forwards the annotated signal to the VCR for recording on 8-mm tapes. The dGPS and laser range and amplitude serial data streams are processed by software that displays the laser trace and the dGPS information as they are fed into the computer, subsamples the laser range and amplitude data, interleaves the subsampled data with the dGPS information, and records the resulting interleaved data stream.

Nelson, Ross↗

NASA NTRS2003

Regenerable Incinerator Exhaust Purification and Trace Contaminant Control System

In this novel approach to air purification, contaminants removed from a process air stream by a high-capacity adsorbent are displaced periodically by a warm, high-humidity, reverse-flow air stream. Displaced contaminants flow into a closed regeneration loop, in which organic compounds are oxidized catalytically and acid gases are removed by a gas- water contactor (which also serves as the source of the water vapor). These features are expected to result in a design that has few expendables and lower energy consumption than alternative regenerable techniques. The joint project between NASA Ames Research Center and Vanderbilt University has completed its third year. Breadboard development continues at NASA Ames, while Vanderbilt has completed most of its adsorption equilibria development. Vanderbilt has completed its fixed-bed apparatus for investigation of dynamic adsorption and desorption processes for trace organic compounds and water vapor, and is continuing its development of the mathematical model describing the column dynamics.

Finn, John E.↗

DOE OSTI2025

Beta-Amino Carboxylate (BAC) non-aqueous physical solvents for enhanced CO2 separations in pre-combustion carbon capture, industrial CO 2 capture, and biogas upgrading processes

Novel beta-amino carboxylate (BAC) solvents have been synthesized and tested to efficiently capture carbon dioxide (CO 2 ) from process gas streams with CO 2 partial pressure intermediate between pre-combustion and post-combustion capture. The BAC solvents have molecular structures characterized by alkyl-substituted amides or esters containing a secondary amine functional group on the second carbon from the carbonyl carbon (referred to as the beta “β” carbon). The ester or amide functional group combined with optimal steric crowding around the amine nitrogen by proximate alkyl groups are tailored to modify the strength of CO 2 binding in the solvent. The solvents possess high CO 2 solubilities and high gas selectivity including good CO 2 /H 2 O selectivity and can be utilized for CO 2 absorption over a range of partial pressures. Due to low volatility, many of the solvents can be operated at or above ambient temperature which eliminates solvent chilling and allows regeneration using low grade waste heat. These novel solvents offer an opportunity for efficient carbon capture for a range of applications including biogas upgrading, hydrogen production, and pre-combustion carbon capture.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2025

Efficient Streaming Dynamic Mode Decomposition

We propose a reformulation of the streaming dynamic mode decomposition method that requires maintaining a single orthonormal basis, thereby reducing computational redundancy. The proposed efficient streaming dynamic mode decomposition method results in a constant-factor reduction in computational complexity and memory storage requirements. Numerical experiments on representative canonical dynamical systems show that the enhanced computational efficiency does not compromise the accuracy of the proposed method.

97 MATHEMATICS AND COMPUTING↗