Search NASA⌕ Search

SEARCH · Search NASA

Results for “surface direction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Analysis and testing for rotordynamic coefficients of turbulent annular seals with different, directionally homogeneous surface-roughness treatment for rotor and stator elements

A theory is presented, based on a simple modification of Hirs' turbulent lubrication equations, to account for different but directionally-homogeneous surface roughness treatments for the rotor and stator of annular seals. The theoretical results agree with von Pragenau's predictions that a damper seal which uses a smooth rotor and a rough stator yields more net damping than a conventional seal which has the same roughness for both the rotor and stator. Experimental results for four stators confirm that properly-designed roughened stators yield higher net damping values and substantially less leakage than seals with smooth surfaces. The best seal from both damping and leakage viewpoints uses a round-hole-pattern stator. Initial results for this stator suggest that, within limits, seals can be designed to yield specified ratios of stiffness to damping.

Childs, D. W.↗
NASA NTRS1975

Roles of airships in economic development

It is proposed that airships of known and tested technology could, in some cases, perform routine transport missions more economically than conventional transport modes. If infrastructure for direct surface transport is already in place or if such infrastructure can be justified by the size of the market and there are no unusual impediments to constructing it, then the airships of tested technology cannot normally compete. If, however, the surface routes would be unusually expensive or circuitous, or if they involve several transhipments, or if the market size is too small to spread infrastructure costs of conventional transport, the airships of tested technology present a workable alternative. A series of special cases are considered. The cases, though unusual, are not unique; there are several similar possible applications which, in total, would provide a reasonably large market for airships.

Beier, G. J.↗
NASA NTRS1977

Synthesis of silane and silicon in a non-equilibrium plasma jet

The feasibility of using a non-equilibrium hydrogen plasma jet as a chemical synthesis tool was investigated. Four possible processes were identified for further study: (1) production of polycrystalline silicon photovoltaic surfaces, (2) production of SiHCl3 from SiCl4, (3) production of SiH4 from SiHCl3, and (4) purification of SiCl4 by metal impurity nucleation. The most striking result was the recognition that the strongly adhering silicon films, amorphous or polycrystalline, produced in our studies could be the basis for preparing a photovoltaic surface directly; this process has potential advantages over other vapor deposition processes.

Calcote, H. F.↗
NASA NTRS1981

Stress concentration in the vicinity of a hole defect under conditions of Hertzian contact

Two dimensional photoelastic stress analyses were conducted for epoxy resin models containing a hole defect under the conditions of Hertzian contact. Stress concentrations around the defect were determined as a function of several parameters. The effect of tangential traction on the stress concentration was also determined. Sharp stress concentrations occur in the vicinity of both the left and the right side of the hole. The stress concentration becomes more distinct the larger the hole diameter and the smaller distance between the hole and the contact surface. The stress concentration is greatest when the disk imposing a normal load is located at the contact surface directly over the hole. The magnitude and the location of stress concentration varies with the distance between the Hertzian contact area and the hole. The area involved in a process of rolling contact fatigue is confined to a shallow region at both sides of the hole. It was found that the effect of tangential traction is comparatively small on the stress concentration around the hole.

Yamamoto, T.↗
NASA NTRS1981

Stress concentration in the vicinity of a hole defect under conditions of Hertzian contact

Two-dimensional photoelastic stress analyses were conducted for epoxy resin models containing a hole defect under the conditions of Hertzian contact. Stress concentrations around the defect were determined as a function of several parameters. These were hole diameter, its vertical distance from the contact surface, and the horizontal distance from the Hertzian contact area. Also determined was the effect of tangential traction (generated by a friction coefficient of 0.1) on the stress concentration. Sharp stress concentrations occur in the vicinity of both the left and the right side of the hole. The stress concentration becomes more distinct the larger the hole diameter and the smaller the distance between the hole and the contact surface. The stress concentration is greatest when the disk imposing a normal load is located at the contact surface directly over the hole. The magnitude and the location of stress concentration varies with the distance between the Hertzian contact area and the hole. Taking into account the stress amplitude, the area which can be involved in a process of rolling contact fatigue seems to be confined to a shallow region at both sides of the hole. The effect of tangential traction is comparatively small on the stress concentration around the hole.

Yamamoto, T.↗
NASA NTRS1982

Automatic algebraic coordinate generation

A computer software system has been developed to automatically generate two-dimensional coordinates from algebraic transformations. For topologically complex regions, a smooth assembly of the transformations can be used to automatically produce a composite mesh where a general gridded format is retained. The algebraic mesh generation system consists of a collection of operator subroutines which are applied to an established data structure and which automatically perform the necessary parts of mesh construction from a sequence of multisurface transformations. The system operators are discussed, taking into account the data base, the order of application, direct surface generators, geometric surface operators, surface generators from existing surfaces, transverse operators, mesh operators, assembly operators, and data visualization operators. Attention is given to applications related to airfoils.

Eiseman, P. R.↗
NASA NTRS1983

900 km of digital ocean wave spectra from the SEASAT SAR

One of the primary reasons for including the SAR in the complement of ocean microwave instruments on SEASAT was the global ocean wave spectra. An accurate, timely, and global knowledge of the full two dimensional or directional surface wave spectra has great value in both operational wave forecasting and in wave climatology, especially in the Southern Oceans. The sparse sampling obtainable from a single orbiting SAR would by itself be inadequate to reconstruct a global wave field, but when supplemented with auxiliary knowledge of the winds, the SAR might provide essential updates to a global wave model.

Beal, R. C.↗
NASA NTRS1983

Anisotropic thermal expansion effects in plasma-sprayed ZrO2-8 percent Y2O3 coatings

The thermal expansion properties of plasma-sprayed ZrO2-8-wt pct Y2O3 coatings, detached from the substrate, have been examined. Coatings were heat-treated in air or in argon. Anisotropic effects in the longitudinal (planar to the substrate surface) and transverse (perpendicular to the substrate surface) directions were measured and related to the coating structure. The thermal expansion coefficient of the coating is discussed in terms of the material's properties, such as the crack network and interlamellar boundary distribution. A precise model for the expansion behavior of coatings still needs attention, since no description of all of the contributing variables exists. A quantitative analysis of thermal properties of coatings will aid in future design and modeling of coating systems.

Berndt, C. C.↗
NASA NTRS1985

Flow control in a diffusing S-Duct

Accurate measurements have been made of secondary flow in a 1.51 area ratio diffusing 30 deg - 30 deg S-Duct with circulair cross section. Turbulent flow was entering the duct at Mach number of 0.6, the boundary layer thickness at the duct entrance was ten percent of the duct inlet diameter. Through measurements made, local flow velocity vector as well as static and total pressures mapping of the flow at several stations were obtained. Strong secondary flow was measured in the first bend which continued into the second bend with new vorticity produced in there in the opposite direction. Surface oil flow visualization and wall pressures indicated a region of separated flow starting at theta approximately equal to 22 deg on the inside of the first bend up to theta approximately equal to 44 deg on the outside of the second bend. The flow separated in 'cyclone' form and never reattached in the duct. As a result of the secondary flow and the flow separation, significant total pressure distortion was observed at the exit of the duct. Using flow control devices the separation was eliminated while the exit distortion was improved.

Vakili, A. D.↗
NASA NTRS1987

Regional sources and sinks of dust on Mars: Viking observations of Cerberus, Solis Planum and Syrtis Major

A study of seasonal variations of albedo features in the Cerberus, Solis Planum, and Syrtis Major regions was based on Viking Orbiter data obtained over more than one complete Martian year. Contour maps of Lambert albedo and single-point thermal inertia were constructed from the Infrared Thermal Mapper (IRTM) experiment data, and Orbiter images were used to determine the pattern and variability of regional winds (inferred from wind streak orientations). Coupled with ground-based radar data, these data allow the regional sediment transport direction, surface properties (texture, morphology, and roughness), and the implications of the observed seasonal and longer term dust redistribution to be investigated. Results are outlined.

Lee, Steven W.↗
NASA NTRS1988

Image processing software for imaging spectrometry data analysis

Imaging spectrometers simultaneously collect image data in hundreds of spectral channels, from the near-UV to the IR, and can thereby provide direct surface materials identification by means resembling laboratory reflectance spectroscopy. Attention is presently given to a software system, the Spectral Analysis Manager (SPAM) for the analysis of imaging spectrometer data. SPAM requires only modest computational resources and is composed of one main routine and a set of subroutine libraries. Additions and modifications are relatively easy, and special-purpose algorithms have been incorporated that are tailored to geological applications.

Mazer, Alan↗
NASA NTRS1987

Regional sources and sinks of dust on Mars: Viking observations of Cerberus, Solis Planum, and Syrtis Major

A study of seasonal variation of albedo features in the Cerberus, Solis Planum, and Syrtis Major regions was based on Viking Orbiter data obtained over more than one complete Martian year. Contour maps of Lambert albedo and single point thermal inertia were constructed from the Infrared Thermal Mapper experiment data, and Orbiter images were used to determine the pattern and variability of regional winds (inferred from wind streak orientations). Coupled with ground based radar data, these data allow the regional sediment transport direction, surface properties (texture, morphology, and roughness), and the implications of the observed seasonal and longer term dust redistribution to be investigated. Results are outlined.

Lee, Steven W.↗
NASA NTRS1990

Diurnal variation of marine stratocumulus over San Nicolas Island during the FIRE IFO

Preliminary analysis was made of data collected at San Nicolas Island during the Intensive Field Observation (IFO) phase of the First International Satellite Cloud Climatology Program's Regional Experiment (FIRE). Of particular interest was an examination of a distinct diurnal variation in the cloud properties, despite an apparent absence of diurnal forcing from the surface. Direct or indirect radiative modulation of such clouds, as proposed by Fravalo at el. (1981) and Turton and Nicholls (1987) indeed seems likely. Preliminary observational evidence for diurnal change in the marine stratocumulus adjacent to San Nicolas Island is presented. A comparison is then made between the observed behavior and predictions from theoretical models of the interactive effect of radiation on boundary layer clouds.

Davies, R.↗
NASA NTRS1993

C-SIDE: The control-structure interaction demonstration experiment

The Control-Structure Interaction Demonstration Experiment (C-SIDE) is sponsored by the Electro-Optics and Cryogenics Division of Ball Aerospace Systems Group. Our objective is to demonstrate methods of solution to structure control problems utilizing currently available hardware in a system that is an extension of our corporate experience. The larger space structures with which Ball has been associated are the SEASAT radar antenna, Shuttle Imaging Radar (SIR) -A, -B and -C antennas and the Radarsat spacecraft. The motivation for the C-SIDE configuration is to show that integration of active figure control in the radar's system-level design can relieve antenna mechanical design constraints. This presentation is primarily an introduction to the C-SIDE testbed. Its physical and functional layouts, and major components are described. The sensor is of special interest as it enables direct surface figure measurements from a remote location. The Remote Attitude Measurement System (RAMS) makes high-rate, unobtrusive measurements of many locations, several of which may be collocated easily with actuators. The control processor is a 386/25 executing a reduced order model-based algorithm with provision for residual mode filters to compensate for structure interaction. The actuators for the ground demonstration are non-contacting, linear force devices. Results presented illustrate some basic characteristics of control-structure interaction with this hardware. The testbed will be used for evaluation of current technologies and for research in several areas. A brief indication of the evolution of the C-SIDE is given at the conclusion.

Mohl, James B.↗
NASA NTRS1993

Thermal-infrared emission spectroscopy of natural surfaces: Application to coated surfaces

Thermal-infrared vibrational spectroscopy has great potential for remotely determining the composition of planetary surface materials by taking advantage of fundamental molecular vibrational modes that produce spectral features in the range from approximately 3 to greater than 50 microns. Much of the current interest in the thermal infrared wavelength region stems from the deployment of multispectral scanners, such as the Thermal Infrared Multispectral Scanner (TIMS) and the Mars Observer Thermal Emission Spectrometer (TES). In order to support these missions, it is necessary to develop an appropriate library of laboratory measurements. The purpose of this work was to develop a technique which, with a very limited set of assumptions, can be used to determine the emissivity of natural surfaces directly by using emitted energy.

Christensen, Philip R.↗
NASA NTRS1997

Bidirectional Brush Seals

Presented is a study of the use of a set of I.D./O.D. bidirectional press seals to reduce the leakage losses in a wave rotor. Relative to the baseline configuration, data indicate the use of brush seals enhanced wave rotor efficiency from 36 to 45 percent at low leakages (small rotor endwall gap spacings) and from 15 to 33 percent at high leakages (larger endwall gap spacings). These brush seals are capable of sealing positive or negative pressure drops with respect to the axial direction. Surface tribology for these tests suggested little evidence of grooving although the bristles appeared polished.

Hendricks, Robert C.↗