Search NASA⌕ Search

SEARCH · Search NASA

Results for “surface treatment”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS2004

Treated Carbon Nanofibers for Storing Energy in Aqueous KOH

A surface treatment has been found to enhance the performances of carbon nanofibers as electrode materials for electrochemical capacitors in which aqueous solutions of potassium hydroxide are used as the electrolytes. In the treatment, sulfonic acid groups are attached to edge plane sites on carbon atoms. The treatment is applicable to a variety of carbon nanofibers, including fibrils and both single- and multiple-wall nanotubes. The reason for choosing nanofibers over powders and other forms of carbon is that nanofibers offer greater power features. In previous research, it was found that the surface treatment of carbon nanofibers increased energy-storage densities in the presence of acid electrolytes. Now, it has been found that the same treatment increases energy-storage densities of carbon nanofibers in the presence of alkaline electrolytes when the carbon is paired with a NiOOH electrode. This beneficial effect varies depending on the variety of carbon substrate to which it is applied. It has been conjectured that the sulfonic acid groups, which exist in a deprotonated state in aqueous KOH solutions, undergo reversible electro-chemical reactions that are responsible for the observed increases in energystorage capacities. The increases can be considerable: For example, in one case, nanofibers exhibited a specific capacitance of 34 Farads per gram before treatment and 172 Farads per gram (an increase of about 400 percent) after treatment. The most promising application of this development appears to lie in hybrid capacitors, which are devices designed primarily for storing energy. These devices are designed to be capable of (1) discharge at rates greater than those of batteries and (2) storing energy at densities approaching those of batteries. A hybrid capacitor includes one electrode like that of a battery and one electrode like that of an electrochemical capacitor. For example, a hybrid capacitor could contain a potassium hydroxide solution as the electrolyte, a carbon capacitor electrode, and a nickel hydroxide battery electrode. By making the capacitor electrode of treated carbon nanofibers instead of another carbon material, one could obtain greater energy-storage capacity.

Firsich, David W.↗
NASA NTRS1975

Development of high temperature resistant graphite fiber coupling agents

Surface treatments were investigated as potential coupling agents to improve the elevated temperature shear strength retention of polyimide/graphite and polyphenylquinoxaline/graphite composites. The potential coupling agents were evaluated by fiber strand tensile tests, fiber and composite weight losses at 533 and 588K, and by interlaminar shear strength retention at 533 and 588K. The two surface treatments selected for more extensive evaluation were a coating of Ventromer T-1, a complex organometallic reaction product of titanium tetrachloride and trimethyl borate, and a polyphenylquinoxaline (PPQ) sizing which was pyrolyzed in nitrogen to form a carbonaceous layer on the fiber. Pyrolyzed polyphenylquinoxaline is a satisfactory coupling agent for polyimide/Thornel 300 graphite fiber composites. During 1000 hours aging at 588K such composites lose a little over half their transverse tensile strength, and suffer a slight loss in flexural modulus. No degradation of flexural strength or interlaminar shear strength occured during 1000 hours aging at 588K. None of the coupling agents examined had a markedly beneficial effect with polyphenylquinoxaline composites.

Griffin, R. N.↗
NASA NTRS1992

Invacuo tribological evaluation of coarse-pitch gears for use on the Space Station alpha joint

Existing invacuo or ambient test data of slow-speed (less than 30 meters/minute pitch line velocity), coarse-pitch gears could not be found suitable for use in evaluating gear materials and surface treatments for the gear-driven bearing race of the Solar Alpha Rotary Joint (SARJ) for Space Station Freedom (SSF). Gear testing was conducted by AEC-Able Engineering Company, Inc. to obtain design data for this critical SSF component. Some bull gear/pinion/lubrication combinations endured over 600,000 cycles (100 SSF years) without measurable wear, while other combinations experienced surface treatment degradation after only 40,000 cycles (seven SSF years). No catastrophic failures, such as seizing or tooth breakage, occurred during any test, all of which were run at least 201,000 cycles (34.5 SSF years). Specific results such as debris characteristics, mechanical efficiencies, effectiveness and degradation of lubrication, and wear data for the various gear combinations tested are described.

Allen, Scotty R.↗
NASA NTRS2011

Modifying Matrix Materials to Increase Wetting and Adhesion

In an alternative approach to increasing the degrees of wetting and adhesion between the fiber and matrix components of organic-fiber/polymer matrix composite materials, the matrix resins are modified. Heretofore, it has been common practice to modify the fibers rather than the matrices: The fibers are modified by chemical and/or physical surface treatments prior to combining the fibers with matrix resins - an approach that entails considerable expense and usually results in degradation (typically, weakening) of fibers. The alternative approach of modifying the matrix resins does not entail degradation of fibers, and affords opportunities for improving the mechanical properties of the fiber composites. The alternative approach is more cost-effective, not only because it eliminates expensive fiber-surface treatments but also because it does not entail changes in procedures for manufacturing conventional composite-material structures. The alternative approach is best described by citing an example of its application to a composite of ultra-high-molecular- weight polyethylene (UHMWPE) fibers in an epoxy matrix. The epoxy matrix was modified to a chemically reactive, polarized epoxy nano-matrix to increase the degrees of wetting and adhesion between the fibers and the matrix. The modification was effected by incorporating a small proportion (0.3 weight percent) of reactive graphitic nanofibers produced from functionalized nanofibers into the epoxy matrix resin prior to combining the resin with the UHMWPE fibers. The resulting increase in fiber/matrix adhesion manifested itself in several test results, notably including an increase of 25 percent in the maximum fiber pullout force and an increase of 60-65 percent in fiber pullout energy. In addition, it was conjectured that the functionalized nanofibers became involved in the cross linking reaction of the epoxy resin, with resultant enhancement of the mechanical properties and lower viscosity of the matrix.

Zhong, Katie↗
NASA NTRS1959

Spectral Emittance of Uncoated and Ceramic-Coated Inconel and Type 321 Stainless Steel

The normal spectral emittance of Inconel and type 321 stainless steel with different surface treatments was measured at temperatures of 900, 1,200, 1,500, and 1,800 F over a wavelength range of 1.5 to 15 microns. The measurements involved comparison of the radiant energy emitted by the heated specimen with that emitted by a comparison standard at the same temperature by means of a recording double-beam infrared spectrophotometer. The silicon carbide comparison standard had previously been calibrated against a laboratory black-body furnace. Surface treatments included electropolishing, sandblasting, electro-polishing followed by oxidation in air for 1/2 hour at 1,800 F, sandblasting followed by oxidation in air for 1/2 hour at 1,800 F, application of National Bureau of Standards coating A-418, and application of NBS ceramic coating N-143. The normal spectral emittance of both alloys in the electropolished condition was low and decreased very slightly with increasing wavelength while in the sandblasted condition it was somewhat higher and did not vary appreciably with wavelength. The oxidation treatment greatly increased the normal spectral emittance of both the electropolished and sandblasted type 321 stainless steel specimens and of the electropolished Inconel specimens and introduced some spectral selectivity into the curves. The oxidation increased the normal spectral emittance of the sandblasted Inconel specimens only moderately. Of the specimens to which a coating about 0.002 inch thick was applied, those coated with A-418 had higher emittance at all wavelengths than did those coated with N-143, and the coated specimens of Inconel had higher spectral emittance at all wavelengths than did the corresponding specimens of type 321 stainless steel. Both coatings were found to be partially transparent to the emitted energy at this thickness but essentially opaque at a thickness of 0.005 inch. Coated specimens with 0.005 inch or more of coating did not show the effect of the underlying metal on spectral emittance, and there was no significant difference at wavelengths greater than about five microns in the normal spectral emittance of specimens having the two coatings. At shorter wavelengths the normal spectral emittance of specimens coated with A-418 was greater than that of specimens coated with N-143.

Richmond, Joseph C.↗
NASA NTRS1976

Simulated studies of wear and friction in total hip prosthesis components with various ball sizes and surface finishes

Experiments were conducted on a newly designed total hip joint simulator. The apparatus closely simulates the complex motions and loads of the human hip in normal walking. The wear and friction of presently used appliance configurations and materials were determined. A surface treatment of the metal femoral ball specimens was applied to influence wear. The results of the investigation indicate that wear can be reduced by mechanical treatment of metal femoral ball surfaces. A metallographic examination and surface roughness measurements were made.

Swikert, M. A.↗
NASA NTRS1981

Improved liquid phase epitaxial GaAs for low series resistance Schottky barrier mixer diodes

Millimeter wave Schottky barrier mixer diodes are extremely important devices for radio astronomy. The performance of the Schottky diodes depends largely on the characteristics and quality of the GaAs epitaxial materials used. Systematic manipulation of the liquid phase epitaxial growth conditions and substrate surface treatments has yielded significantly improved surface morphology. Initial problems of high resistivity interfacial layers have been reduced without the use of an in situ etchback. Two-micron diameter Schottky diodes fabricated from epitaxial layers grown at 725 C exhibit a 9-ohm series resistance very near the theoretical minimum.

Binari, S. C.↗
NASA NTRS1988

Extending Fatigue Lives Of Selected Alloys

Rejuvenating treatments demonstrated. Experiments with three alloys show some combinations of heat treatment, hot isostatic pressing, and/or surface treatment extends cycle lives of fatigue-damaged or fatigue-precracked specimens. For each alloy, tests were first done to determine "baseline" high-cycle-fatigue lives and high-cycle-fatigue failure modes over range of test conditions. Controlled fatigue damage introduced into specimens. Damaged specimens subjected to candidate rejuvenating treatments, then tested to failure. Effectiveness of each treatment judged by comparing fatigue data of damaged and treated specimens to "baseline" fatigue and data taken at same test conditions.

Matejczyk, D. E.↗
NASA NTRS1998

Ion Implantation of Perfluoropolyether-Lubricated Surfaces for Improved Tribological Performance

For over 30 years, perfluoropolyethers (PFPE's) have been the liquid lubricants of choice for space applications because of their proven tribological performance and desirable properties, such as low vapor pressure and a wide liquid temperature range. These oils are used in such space mechanisms as gyroscopes, scanning mirrors, actuators, and filter wheels. In the past few years, there have been several incidents during which PFPE-lubricated space mechanisms have shown anomalous behavior. These anomalies are thought to be the result of PFPE degradation. Investigative research focused on understanding and modeling the degradation of PFPE lubricants has shown that PFPE's degrade and lose their desirable properties while under boundary-lubricated, sliding/rolling contacts and at elevated temperatures. These performance deficiencies are strongly dependent on the surface chemistry and reactivity of the lubricated contacts, which dictate the formation of harmful catalytic by-products. One way to inhibit tribo-induced degradation may be to use passivated surfaces that do not promote the formation of harmful by-products. Such a passivated surface would inhibit PFPE degradation and increase the lifetime of the lubricated mechanism. Ion implantation is one such passivation technique. This surface-treatment technique can modify the surface properties of materials without affecting either the properties or dimensions of the bulk material beneath the treated layer. By introducing a foreign species into a submicron surface layer, ion implantation can induce unique surface microstructures.

Shogrin, Brad↗
NASA NTRS1988

Interfaces in polymer, ceramic, and metal matrix composites; Proceedings of the Second International Conference on Composite Interfaces (ICCI-II), Cleveland, OH, June 13-17, 1988

The present conference on interfacial factors in advanced composite materials discusses such topics in their development status and properties as silane coupling, the electrochemical and plasma-surface treatment of carbon fibers, fiber surface-analytical techniques, polymer molecular scale characterization by atom-probe field-ion microscopy, the study of carbon fiber-epoxy resin interface interactions by means of labeling techniques, and the surface tailoring of SiC by ion implantation. Also discussed are developments in laser light-scattered photoelasticity, microstructural evolutions under heat treatment and radiation damage, TEM for composites, the interfaces of carbon fiber-reinforced Al composites, the influence of the interface on macroscopic composite properties, and the status of the theoretical understanding of composite interfaces.

Ishida, Hatsuo↗
NASA NTRS1990

New Materials And Treatments For Turbopump Bearings

Report evaluates materials and surface treatments for bearings for liquid-oxygen turbopumps. Key properties sought for application are low friction, low wear, and resistance to corrosion and rolling-contact fatigue.

Wedeven, L. D.↗
NASA NTRS2019

Plasma Surface Functionalization of AFP Manufactured Composites for Improved Adhesive Bond Performance

Application of carbon fiber reinforced polymer (CFRP) as a high-performance structural material has widespread application in the present aerospace industry. However, as-processed composite materials require a comprehensive surface treatment prior to bonding to remove contaminants and impart surface functionality and topography to overcome their poor adhesion properties. Atmospheric pressure plasma jet treatment (APPJT) has been increasingly garnering attention as an alternate method for surface preparation of CFRP. This method has been reported to achieve success in imparting favorable polar functional groups into the composite surfaces enhancing wettability and surface energy of the bonded surfaces. In some cases, APPJT has been demonstrated to remove contaminants or, in the case of silicones, convert them to silica. In this study, an atmospheric pressure plasma jet (APPJ) system was used for surface activation of a composite laid-up by an automated fiber placement (AFP) machine. Surface modifications prior to and after treatment were characterized using water contact angle (WCA) measurements, X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), and atomic force microscopy (AFM). Double cantilever beam (DCB) tests were performed to quantify the bonding performance of the composites. The results show a marked enhancement of the mode I interlaminar fracture toughness with the application of APPJT.

Sarikaya, Ibrahim↗
NASA NTRS1975

Effect of polymer properties and adherend surfaces on adhesion

The surface properties associated with good adhesive joints were evaluated in terms of application of adhesive bonding in aerospace technology. The physical and chemical nature was determined of Ti and Al adherend surfaces after various surface treatments, and the effects on fracture surfaces of high temperature aging, and variations in amide, anhydride, and solvent during polymer synthesis. The effects were characterized of (1) high temperature during shear strength testing, (2) fiber-reinforced composites as adherends, (3) acid/base nature of adherends, (4) aluminum powder adhesive filler, and (5) bonding pressure.

Dwight, D. W.↗
NASA NTRS2004

Structural Evaluation of Radially Expandable Cardiovascular Stents Encased in a Polyurethane Film

A method of encasing cardiovascular stents with an expandable polyurethane coating has been developed to provide a smooth homogeneous inner wall allowing for a confluent growth of endothelial cells. In this design, the metal wire stent structure is completely covered by the polyurethane film minimizing biocorrosion of the metal (stainless steel or nitinol), and providing a homogeneous surface for surface treatment and incorporation of various eluting drugs to prevent platelet aggregation while supporting endothelialization. The polyurethane surface was treated with a helium plasma for sterilization and promotes growth of cells. The paper details the performance of the coated film to expand with the metal stent up to 225 % during deployment. We present stress/strain behavior of polyurethane films, and subsequent plasma treatment of the surface and the adhesion of the coating to the stent structure upon expansion. A film of less than 25 tm was found to be sufficient for corrosion resistance and flexibility without producing any excess stress on the stent structure. Straining the film to 225 % and plasma modification did not affect the mechanical and surface properties while allowing for improved biocompatibility as determined by the critical surface tension, surface chemistry, and roughness.

Trigwell, Steve↗
NASA NTRS1977

Surface photovoltage in exciton absorption range in CdS

The high resolution, intrinsic spectra of surface photovoltage are reported for semiconducting n-type CdS single crystals. At reduced temperatures (120-160 K) the spectra exhibit three sharp maxima due to A, B and C free exciton transitions. Energy positions of these lines and valence band parameters (spin-orbit and crystal field splittings) estimated from surface photovoltage are in good agreement with values obtained by other methods. The excitonic transitions are very sensitive to surface treatment, i.e. polishing, etching, background illumination and surface doping. The mechanism of direct interaction of free excitons with surface states is proposed to explain exciton lines in surface photovoltage.

Morawski, A.↗