Search NASA⌕ Search

SEARCH · Search NASA

Results for “sweep testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

The role of modeling and flight testing in rotorcraft parameter identification

The importance of recognizing that each lower-order model used for rotorcraft parameter identification has a limited range of applicability is illustrated in some detail. Examples are given to illustrate the use of conditioning the test input signals and the potential of using multi-axis test inputs to enhance the parameter identifiability. The paper discusses the benefits and limitations of using frequency sweeps as flight-test input signals for identification of frequency response for rotorcraft and for the subsequent fitting of parametric transfer-function models. This paper demonstrates the major role played by analytical modeling and the understanding of the physics involved in the rotorcraft flight dynamics, particularly understanding the limit of lower-order models, in achieving successful rotorcraft parameter identification.

Chen, R. T. N.↗
NASA NTRS1995

Pressure-sensitive paint measurements on a supersonic high-sweep oblique wing model

The pressure-sensitive paint method was used in the test of a high-sweep oblique wing model, conducted in the NASA Ames 9- by 7-ft Supersonic Wind Tunnel. Surface pressure data was acquired from both the luminescent paint and conventional pressure taps at Mach numbers between M = 1.6 and 2.0. In addition, schlieren photographs of the outer flow were used to determine the location of shock waves impinging on the model. The results show that the luminescent pressure-sensitive paint can capture both global and fine features of the static surface pressure field. Comparison with conventional pressure tap data shows good agreement between the two techniques, and that the luminescent paint data can be used to make quantitative measurements of the pressure changes over the model surface. The experiment also demonstrates the practical considerations and limitations that arise in the application of this technique under supersonic flow conditions in large-scale facilities, as well as the directions in which future research is necessary in order to make this technique a more practical wind-tunnel testing tool.

McLachlan, B. G.↗
NASA NTRS1978

Swept group delay measurement

Direct recording of group delay measurements on a system under temperature and stress tests employs modulated carrier frequency sweep over an S or X band. Reference path and test paths to separate detectors utilize a power divider e.g., a directional coupler or a hybrid T junction. An initially balanced phase comparator is swept in frequency by modulated carrier over the band of interest for different conditions of temperature and/or mechanical stress to obtain characteristic group delay curves.

Trowbridge, D. L.↗
NASA NTRS1992

Environmental qualification testing of payload G-534, the Pool Boiling Experiment

Payload G-534, the prototype Pool Boiling Experiment (PBE), is scheduled to fly on the STS-47 mission in September 1992. This paper describes the purpose of the experiment and the environmental qualification testing program that was used to prove the integrity of the hardware. Component and box level vibration and thermal cycling tests were performed to give an early level of confidence in the hardware designs. At the system level, vibration, thermal extreme soaks, and thermal vacuum cycling tests were performed to qualify the complete design for the expected shuttle environment. The system level vibration testing included three axis sine sweeps and random inputs. The system level hot and cold soak tests demonstrated the hardware's capability to operate over a wide range of temperatures and gave wider latitude in determining which shuttle thermal attitudes were compatible with the experiment. The system level thermal vacuum cycling tests demonstrated the hardware's capability to operate in a convection free environment. A unique environmental chamber was designed and fabricated by the PBE team and allowed most of the environmental testing to be performed within the hardware build laboratory. The completion of the test program gave the project team high confidence in the hardware's ability to function as designed during flight.

Sexton, J. Andrew↗
NASA NTRS1992

Environmental qualification testing of the prototype pool boiling experiment

The prototype Pool Boiling Experiment (PBE) flew on the STS-47 mission in September 1992. This report describes the purpose of the experiment and the environmental qualification testing program that was used to prove the integrity of the prototype hardware. Component and box level vibration and thermal cycling tests were performed to give an early level of confidence in the hardware designs. At the system level, vibration, thermal extreme soaks, and thermal vacuum cycling tests were performed to qualify the complete design for the expected shuttle environment. The system level vibration testing included three axis sine sweeps and random inputs. The system level hot and cold soak tests demonstrated the hardware's capability to operate over a wide range of temperatures and gave the project team a wider latitude in determining which shuttle thermal altitudes were compatible with the experiment. The system level thermal vacuum cycling tests demonstrated the hardware's capability to operate in a convection free environment. A unique environmental chamber was designed and fabricated by the PBE team and allowed most of the environmental testing to be performed within the project's laboratory. The completion of the test program gave the project team high confidence in the hardware's ability to function as designed during flight.

Sexton, J. Andrew↗
DOE OSTI2015

Field testing of modular borehole monitoring with simultaneous distributed acoustic sensing and geophone vertical seismic profiles at Citronelle, Alabama: Field testing of MBM

A modular borehole monitoring concept has been implemented to provide a suite of well-based monitoring tools that can be deployed cost effectively in a flexible and robust package. The initial modular borehole monitoring system was deployed as part of a CO 2 injection test operated by the Southeast Regional Carbon Sequestration Partnership near Citronelle, Alabama. The Citronelle modular monitoring system transmits electrical power and signals, fibre-optic light pulses, and fluids between the surface and a reservoir. Additionally, a separate multi-conductor tubing-encapsulated line was used for borehole geophones, including a specialized clamp for casing clamping with tubing deployment. The deployment of geophones and fibre-optic cables allowed comparison testing of distributed acoustic sensing. We designed a large source effort (>64 sweeps per source point) to test fibre-optic vertical seismic profile and acquired data in 2013. The native measurement in the specific distributed acoustic sensing unit used (an iDAS from Silixa Ltd) is described as a localized strain rate. Following a processing flow of adaptive noise reduction and rebalancing the signal to dimensionless strain, improvement from repeated stacking of the source was observed. Conversion of the rebalanced strain signal to equivalent velocity units, via a scaling by local apparent velocity, allows quantitative comparison of distributed acoustic sensing and geophone data in units of velocity. We see a very good match of uncorrelated time series in both amplitude and phase, demonstrating that velocity-converted distributed acoustic sensing data can be analyzed equivalent to vertical geophones. We show that distributed acoustic sensing data, when averaged over an interval comparable to typical geophone spacing, can obtain signal-to-noise ratios of 18 dB to 24 dB below clamped geophones, a result that is variable with noise spectral amplitude because the noise characteristics are not identical. With vertical seismic profile processing, we demonstrate the effectiveness of downgoing deconvolution from the large spatial sampling of distributed acoustic sensing data, along with improved upgoing reflection quality. finally, we conclude that the extra source effort currently needed for tubing-deployed distributed acoustic sensing vertical seismic profile, as part of a modular monitoring system, is well compensated by the extra spatial sampling and lower deployment cost as compared with conventional borehole geophones.

58 GEOSCIENCES↗
NASA NTRS1997

Aerodynamics of a Simple Three-Dimensional High-Lift System

Experimental results are presented for a three-element high-lift system with a half-span flap and both a full- and three-quarter span slat. The simplified wing spanned the wind-tunnel test section with no wing sweep or wing tip. Full- and part-span slat configurations were tested to investigate the three-dimensional effects of a finite-span slat in a landing configuration. With a part-span slat, flow visualization and surface pressures revealed two vortices at the flap tip and one at the slat tip. Compared to the full-span slat case, the part-span slat configuration stalled at a lower angle of attack and yielded reduced lift at all angles of attack. At a representative approach attitude (10 deg), wake surveys indicated comparable induced drag for the full- and part-span slat configurations while the profile drag was more than doubled with a part-span slat. The vorticity contribution of the slat-tip vortex was minimal, suggesting that the vortex dissipates through viscous interaction with the main-element boundary layer. The addition of a lower-surface fence at the slat tip yielded two co-rotating vortices and partially alleviated the profile drag increase of the part-span slat.

Storms, Bruce↗
NASA NTRS2015

Performance Enhancement of a Full-Scale Vertical Tail Model Equipped with Active Flow Control

This paper describes wind tunnel test results from a joint NASA/Boeing research effort to advance active flow control (AFC) technology to enhance aerodynamic efficiency. A full-scale Boeing 757 vertical tail model equipped with sweeping jet actuators was tested at the National Full-Scale Aerodynamics Complex (NFAC) 40- by 80-Foot Wind Tunnel (40x80) at NASA Ames Research Center. The model was tested at a nominal airspeed of 100 knots and across rudder deflections and sideslip angles that covered the vertical tail flight envelope. A successful demonstration of AFC-enhanced vertical tail technology was achieved. A 31- actuator configuration significantly increased side force (by greater than 20%) at a maximum rudder deflection of 30deg. The successful demonstration of this application has cleared the way for a flight demonstration on the Boeing 757 ecoDemonstrator in 2015.

Whalen, Edward A.↗
NASA NTRS2018

Full-Scale Testing of Active Flow Control Enhanced Vertical Tail

This paper describes wind tunnel test results from a joint NASA/Boeing research effort to advance active flow control (AFC) technology to enhance aerodynamic efficiency. A full-scale Boeing 757 vertical tail model equipped with 37 sweeping jet actuators was tested at the National Full-Scale Aerodynamics Complex (NFAC) 40- by 80-Foot Wind Tunnel (40x80) at NASA Ames Research Center. The model was tested at a nominal airspeed of 100 knots and across rudder deflections and sideslip angles that covered the vertical tail flight envelope. The flow separation control optimization was performed at the maximum rudder deflection of 30° and sideslip angles of 0° and -7.5°. Greater than 20% increase in side force were achieved at maximum rudder deflection and the two sideslip angles with a 31-actuator configuration. AFC caused significant increases in suction pressure on the actuator side and associated side force enhancement. The successful demonstration of this application cleared the way for a subsequent flight demonstration on the Boeing 757 ecoDemonstrator in 2015.

Whalen, Edward A.↗
NASA NTRS1987

Supersonic boundary-layer transition on the LaRC F-106 and the DFRF F-15 aircraft. Part 1: Transition measurements and stability analysis

For the case of the F-15 flight tests, boundary layer transition was observed up to Mach numbers of 1.2. For very limited and specific flight conditions, laminar flow existed back to about 20 percent chord on the surface clean up glove. Hot film instrumentation was effective for locating the region of transition. For the F-106 flight tests, transition on the wing or vertical tail generally occurred very near the attachment line. Transition was believed to be caused by either attachment line contamination or strong cross flow development due to the high sweep angles of the test articles. The compressibility analysis showed that cross flow N-factors were in the range of 5 to 12 at transition.

Collier, Fayette S., Jr.↗
NASA NTRSDate not supplied

FUN3D Analyses in Support of the 1st AIAA Stability and Control Prediction Workshop

The 1st AIAA Stability and Control Prediction Workshop was created to establish best practices for the prediction of stability & control derivatives using computational fluid dynamics and assess the limitations of these computational methods when those best practices are applied. The inaugural workshop considers the ONERA version of the NASA/Boeing Common Research Model(CRM), which includes the wing, body, horizontal tail, and a vertical tail designed by ONERA. Wind tunnel tests have been conducted for this configuration with longitudinal tests having been previously published, in addition to unpublished data at small sideslip angles that will serve as ‘blind’ data for workshop data comparisons. Participants were provided a ‘family’ of unstructured grids for the full-span ONERA CRM model with the wind-tunnel sting included. This family of mixed-element grids consists of 5 levels of refinement (tiny, coarse, medium, fine, and extra fine) with surface and volume mesh scaling, resulting in a size range of 14.6 to 53.4 million nodes. In addition, a medium refinement mesh has been provided for the ONERA CRM configuration without a sting to evaluate the sting’s impact on static longitudinal stability characteristics. In addition to these workshop-provided grids, the present work also considers an equivalent ‘family’ of computational grids generated using Heldenmesh™, a rapid grid generation software by Helden Aerospace Corporation for creating high-quality, three-dimensional, mixed-element unstructured meshes. Because of the authors’ familiarity with this software, these additional grids were generated as a comparison to the workshop-provided grids and to better understand the implications of using volume-mirrored grids for stability and control predictions. The present work will contribute to the workshop with test case data generated using the NASA FUN3D code, a parallelized, unstructured, node-based, finite-volume discretization, Reynolds-averaged Navier-Stokes flow solver. Numerical simulations will be conducted using the Quadratic Constitutive Relationship (QCR) version of the Spalart-Allmaras (SA) turbulence model with negative turbulence variable provisions. Both steady and2nd-order, time-accurate simulation results are to be generated and compared for select test cases, as time permits, to investigate their impact on FUN3D predictions. The present work will consider the three primary workshop test cases: (1) grid convergence study, (2) Mach number effect on static stability, and (3) wind tunnel sting increments. Additionally, data will be provided for the two optional test cases, which include:(1) static stability derivative calculations and (2)sideslip angle sweeps. In each of the test cases, the vehicle is stationary, and the body is assumed to be rigid, where vehicle deformation has been accounted for in the model configuration geometry. For all test cases, longitudinal and lateral force and moment aerodynamic coefficients will be provided for the total configuration, in addition to a component-level breakdown that includes the port wing, starboard wing, fuselage, and tail.

CFD↗
DOE OSTI2026

Rhythm

Rhythm is a small Python framework that automates Cadence Spectre simulations from the command line. Instead of creating an ADE testbench, you'll write a Rhythm Recipe, a short, readable Python script that contains each step needed to test your circuit from setting up libraries and stimulus waveforms to setting up analyses and reading the results (in Rhythm, these steps are called stages). Need to run more than one simulation? Use a Rhythm Campaign to easily sweep across corners and test conditions with a live dashboard and multithreading support.

Quinn, Adam [Fermi National Accelerator Laboratory↗
NASA NTRS1939

Wind-tunnel Investigation of Effect of Yaw on Lateral-stability Characteristics I : Four N.A.C.A. 23012 Wings of Various Plan Forms with and Without Dihedral

Four N.A.C.A. 23012 wings were tested at several angles of yaw in the N.A.C.A. 7- by 10-foot wind tunnel. All the wings have rounded tips and, in plan form, one is rectangular and the others are tapered 3:1 with various amounts of sweep. Each wing was tested with two amounts of dihedral and with partial-span split flaps. The coefficients of lift, drag, and pitching moment are given for all the models at zero yaw. The coefficients of rolling moment, yawing moment, and side force are given for the rectangular wing at all values of yaw tested. The rate of change in the coefficients with angle of yaw is given in convenient form for stability calculations.

Bamber, M J↗
NASA NTRS2019

European Service Module - Structural Test Article (E-STA) Building Block Test Approach and Model Correlation Observations

The Orion European Service Module - Structural Test Article (E-STA) underwent sine vibration testing in 2016 using the Mechanical Vibration Facility (MVF) multi-axis shaker system at NASA Glenn Research Center’s (GRC) Plum Brook Station (PBS) Space Power Facility (SPF). The main objective was to verify the structural integrity of the European Service Module (ESM) under sine sweep dynamic qualification vibration testing. A secondary objective was to perform a fixed-base modal survey, while E-STA was still mounted to MVF, in order to achieve a test correlate the finite element model (FEM). To facilitate the E-STA system level correlation effort, a building block test approach was implemented. Modal tests were performed on two major subassemblies, the crew module/launch abort structure (CM/LAS) and the crew module adapter (CMA) mass simulators. These subassembly FEMs were individually correlated and then integrated into the E-STA FEM prior to the start of the E-STA sine vibration test. This paper summarizes the modal testing and model correlation efforts of both of these subassemblies and how the building block approach assisted in the overall correlation of the E-STA FEM. This paper will also cover modeling practices that should be avoided, recommended instrumentation positioning on complex structures, and the importance of the FEM geometrically matching CAD in sufficient detail in order to adequately replicate internal load paths. The goal of this paper is to inform the reader of the hard earned lessons learned and pitfalls to avoid when applying a building block test approach.

Winkel, James P.↗
NASA NTRS1972

Dynamic stability derivatives at angles of attack from minus 5 deg to 90 deg for a variable-sweep fighter configuration with twin vertical tails

An investigation was conducted in the Langley full-scale tunnel to determine the dynamic stability derivatives in pitch, roll, and yaw over an angle-of-attack range of -5 deg to 90 deg for a variable-sweep fighter configuration with twin vertical tails. The study consisted of forced-oscillation tests of a 1/10-scale model of the airplane at a Reynolds number of 0.4 million based on the reference wing mean aerodynamic chord. Tests were conducted for wing sweep angles of 22 deg, 35 deg, 50 deg, and 68 deg, and the effects of the vertical and horizontal tails, wing leading-edge slats, nose-mounted canards, and frequency of the oscillation were also evaluated.

Grafton, S. B.↗
NASA NTRS1995

Application of impact dampers in vibration control of flexible structures

Impact dampers belong to the category of passive vibration devices used to attenuate the vibration of discrete and continuous systems. An impact damper generally consists of a mass which is allowed to travel freely between two defined stops. Under the right conditions, the vibration of the structure to which the impact damper is attached will cause the mass of the impact damper to strike the structure. Previous analytical and experimental research work on the effect of impact dampers in attenuating the vibration of discrete and continuous systems have demonstrated their effectiveness. It has been shown in this study that impact dampers can increase the intrinsic damping of a lightly-damped flexible structure. The test structure consists of a slender flexible beam supported by a pin-type support at one end and supported by a linear helical flexible spring at another location. Sinusoidal excitation spanning the first three natural frequencies was applied in the horizontal plane. The orientation of the excitation and the test structure in the horizontal plane minimizes the effect of gravity on the behavior of the test structure. The excitation was applied using a linear sine sweep technique. The span of the test structure, the mass of the impact damper, the distance of travel, and the location of the impact damper along the span of the test structure were varied. The damping ratio are estimated for sixty test configurations. The results show that the impact damper significantly increases the damping ratio of the test structure. Statistical analysis of the results using the method of multiple linear regression indicates that a reasonable fit has been accomplished. It is concluded that additional experimental analysis of flexible structures in microgravity environment is needed in order to achieve a better understanding of the behavior of impact damper under conditions of microgravity. Numerical solution of the behavior of flexible structures equipped with impact dampers is also needed to predict stresses and deformations under operating conditions of microgravity in space applications.

Akl, Fred A.↗