Search NASA⌕ Search

SEARCH · Search NASA

Results for “task design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

Design of 3-D Nacelle near Flat-Plate Wing Using Multiblock Sensitivity Analysis (ADOS)

One of the major design tasks involved in reducing aircraft drag is the integration of the engine nacelles and airframe. With this impetus, nacelle shapes with and without the presence of a flat-plate wing nearby were optimized. This also served as a demonstration of the 3-D version of the recently developed aerodynamic design optimization methodology using sensitivity analysis, ADOS. The required flow analyses were obtained by solving the three-dimensional, compressible, thin-layer Navier-Stokes equations using an implicit, upwind-biased, finite volume scheme. The sensitivity analyses were performed using the preconditioned version of the SADD scheme (sensitivity analysis on domain decomposition). In addition to demonstrating the present method's capability for automatic optimization, the results offered some insight into two important issues related to optimizing the shapes of multicomponent configurations in close proximity. First, inclusion of the mutual interference between the components resulted in a different shape as opposed to shaping an isolated component. Secondly, exclusion of the viscous effects compromised not only the flow physics but also the optimized shapes even for isolated components.

Eleshaky, Mohamed E.↗

Integrated application of active controls (IAAC) technology to an advanced subsonic transport project. Initial ACT configuration design study

The initial ACT configuration design task of the integrated application of active controls (IAAC) technology project within the Energy Efficient Transport Program is summarized. A constrained application of active controls technology (ACT) resulted in significant improvements over a conventional baseline configuration previously established. The configuration uses the same levels of technology, takeoff gross weight, payload, and design requirements/objectives as the baseline, except for flying qualities, flutter, and ACT. The baseline wing is moved forward 1.68 m. The configuration incorporates pitch-augmented stability (which enabled an approximately 10% aft shift in cruise center of gravity and a 45% reduction in horizontal tail size), lateral/directional-augmented stability, an angle of attack limiter, wing load alleviation, and flutter mode control. This resulted in a 930 kg reduction in airplane operating empty weight and a 3.6% improvement in cruise efficiency, yielding a 13% range increase. Adjusted to the 3590 km baseline mission range, this amounts to 6% block fuel reduction and a 15.7% higher incremental return on investment, using 1978 dollars and fuel cost.

Source record↗

Human Research Program Human Health Countermeasures Element Bone and Muscle Risk Standing Review Panel (SRP)

The Bone and Muscle Risk Standing Review Panel (SRP) met at the NASA Johnson Space Center (JSC) on October 4-6, 2009 to discuss the areas of current and future research targeted by the Human Health Countermeasures (HHC) Element of the Human Research Program (HRP). Using evidence-based knowledge as a background for identified risks to astronaut health and performance, NASA had identified gaps in knowledge to address those risks. Ongoing and proposed tasks were presented to address the gaps. The charge to the Bone and Muscle Risk SRP was to review the gaps, evaluate whether the tasks addressed these gaps and to make recommendations to NASA s HRP Science Management Office regarding the Panel's review. The Bone and Muscle Risk SRP consisted of scientists who are experts in muscle, bone, or both and could evaluate the existing evidence with sufficient knowledge of the potential effects of long duration exposure to microgravity. More important, although expertise in basic science is important, the SRP was requested to evaluate the practicality of the proposed efforts in light of the realistic demands placed on the HRP. In short, all tasks presented in the Integrated Research Plan (IRP) should address specific questions related to the challenges faced by the astronauts as a result of prolonged exposure to microgravity. All tasks proposed to fill the gaps in knowledge should provide applied, translational data necessary to answer the specific questions. Several presentations were made to the SRP during the site visit and the SRP spent sufficient time to address the panel charge, either as a group or in separate sessions for the Bone and Muscle Risk subgroups. The SRP made a final debriefing to the HRP Program Scientist, Dr. John B. Charles, on October 6, 2009. Taking the evidence and identified risks as givens, the SRP concluded that 1) integration of information should lead to a more comprehensive approach to identifying the gaps, 2) not all tasks addressed the gaps as stated in the IRP, 3) better access should be given to the SRP to existing data to include in its review, and 4) there were some missing gaps and tasks. As a result the SRP recommended 1) combining certain gaps, which in some cases were addressed with identical tasks, 2) additional gaps and tasks to address some of the gaps, 3) deleting some gaps and tasks to better focus the efforts of NASA s HRP in prioritizing their efforts, and 4) prioritizing gaps to address significant issues needing resolution in the short term while maintaining an awareness of long-term goals. The SRP commended the efforts by the HHC Element to integrate knowledge gaps and design tasks to address the higher order questions. This integration did not apply to the Bone and Muscle Risk alone, but the musculoskeletal system as its functions integrate with issues in

Glowacki, Julie↗

Linear modelling of attentional resource allocation

Eight subjects time-shared performance of two compensatory tracking tasks under conditions when both were of constant difficulty, and when the control order of one task (designated primary) was varied over time within a trial. On line performance feedback was presented on half of the trials. The data are interpreted in terms of a linear model of the operator's attention allocation system, and suggest that this allocation is strongly suboptimal. Furthermore, the limitations in reallocating attentional resources between tasks, in response to difficulty fluctuations were not reduced by augmented performance feedback. Some characteristics of the allocation system are described, and reasons for its limitations suggested.

Pierce, B.↗

Mars habitat

The objective of this study is to develop a conceptual design for a permanently manned, self-sustaining Martian facility, to accommodate a crew of 20 people. The goal is to incorporate the major functions required for long term habitation in the isolation of a barren planet into a thriving ecosystem. These functions include living, working, service, and medical facilities as well as a green house. The main design task was to focus on the internal layout while investigating the appropriate structure, materials, and construction techniques. The general concept was to create a comfortable, safe living environment for the crew members for a stay of six to twelve months on Mars. Two different concepts were investigated, a modular assembly reusable structure (MARS) designated Lavapolis, and a prefabricated space frame structure called Hexamars. Both models take into account factors such as future expansion, radiation shielding, and ease of assembly.

Ayers, Dale↗

Benefits of Matching Domain Structure for Planning Software: The Right Stuff

We investigated the role of domain structure in software design. We compared 2 planning applications, for a Mission Control group (International Space Station), and measured users speed and accuracy. Based on our needs analysis, we identified domain structure and used this to develop new prototype software that matched domain structure better than the legacy system. We took a high-fidelity analog of the natural task into the laboratory and found (large) periformance differences, favoring the system that matched domain structure. Our task design enabled us to attribute better periormance to better match of domain structure. We ran through the whole development cycle, in miniature, from needs analysis through design, development, and evaluation. Doing so enabled inferences not just about the particular systems compared, but also provided evidence for the viability of the design process (particularly needs analysis) that we are exploring.

Billman, Dorrit Owen↗

The environmental control and life support system for a lunar base - What drives its design

It is noted that no single ECLSS is uniquely applicable to a mission of given crew size and duration; all mission parameters, together with details of other systems, must accordingly be factored into the lunar base ECLSS design process that is presently discussed. Experience to date with ECLSS design tasks indicates that mission planners and systems engineers should refrain from emphasizing the 'closed loop' aspects of such systems, since even the best regenerative processes will involve expendable materials that must be resupplied; resupply logistics will accordingly constitute a considerable effort of lunar base operation. Technology development status for processes and subsystems is identified as a major ECLSS design driver.

Hypes, Warren D.↗

The C-5A active lift distribution control system

The ALDCS development and design tasks, ALDCS functional configuration, and resulting challenges encountered while accomplishing the first phase of the program are described. These tasks are establishing system requirements and criteria and synthesizing a system mechanization to meet the desired load alleviation, stability margins, flight safety, and flying qualities performance. Results of the ALDCS development and prototype system flight simulation programs, and control law optimization including system stability, handling qualities and structural load analyses are presented, along with concluding remarks relative to the system design integration.

Hargrove, W. J.↗

Alloy Design Workbench-Surface Modeling Package Developed

NASA Glenn Research Center's Computational Materials Group has integrated a graphical user interface with in-house-developed surface modeling capabilities, with the goal of using computationally efficient atomistic simulations to aid the development of advanced aerospace materials, through the modeling of alloy surfaces, surface alloys, and segregation. The software is also ideal for modeling nanomaterials, since surface and interfacial effects can dominate material behavior and properties at this level. Through the combination of an accurate atomistic surface modeling methodology and an efficient computational engine, it is now possible to directly model these types of surface phenomenon and metallic nanostructures without a supercomputer. Fulfilling a High Operating Temperature Propulsion Components (HOTPC) project level-I milestone, a graphical user interface was created for a suite of quantum approximate atomistic materials modeling Fortran programs developed at Glenn. The resulting "Alloy Design Workbench-Surface Modeling Package" (ADW-SMP) is the combination of proven quantum approximate Bozzolo-Ferrante-Smith (BFS) algorithms (refs. 1 and 2) with a productivity-enhancing graphical front end. Written in the portable, platform independent Java programming language, the graphical user interface calls on extensively tested Fortran programs running in the background for the detailed computational tasks. Designed to run on desktop computers, the package has been deployed on PC, Mac, and SGI computer systems. The graphical user interface integrates two modes of computational materials exploration. One mode uses Monte Carlo simulations to determine lowest energy equilibrium configurations. The second approach is an interactive "what if" comparison of atomic configuration energies, designed to provide real-time insight into the underlying drivers of alloying processes.

Abel, Phillip B.↗

AESOP: An interactive computer program for the design of linear quadratic regulators and Kalman filters

AESOP is a computer program for use in designing feedback controls and state estimators for linear multivariable systems. AESOP is meant to be used in an interactive manner. Each design task that the program performs is assigned a "function" number. The user accesses these functions either (1) by inputting a list of desired function numbers or (2) by inputting a single function number. In the latter case the choice of the function will in general depend on the results obtained by the previously executed function. The most important of the AESOP functions are those that design,linear quadratic regulators and Kalman filters. The user interacts with the program when using these design functions by inputting design weighting parameters and by viewing graphic displays of designed system responses. Supporting functions are provided that obtain system transient and frequency responses, transfer functions, and covariance matrices. The program can also compute open-loop system information such as stability (eigenvalues), eigenvectors, controllability, and observability. The program is written in ANSI-66 FORTRAN for use on an IBM 3033 using TSS 370. Descriptions of all subroutines and results of two test cases are included in the appendixes.

Lehtinen, B.↗

Allowable response delay for large aircraft

The degree of permissible time delay in an airliner flight control system is presently sought by means of a pilot-in-the-loop moving base flight simulator, assuming the characteristics of an advanced L-1011 aircraft variant. Test pilots and engineers from the U.S. Navy, the airliner manufacturer, and NASA Langley were used in a task which encompassed approach and landing after recovery from offsets in localizer and glide slope, during calm, turbulent, and cross-wind conditions. The data obtained in the course of 279 runs included statistics on pilot workload and performance as well as pilot opinion. Preliminary results indicate that requirements for a 0.1-sec maximum delay in aircraft response are excessively conservative for large aircraft, where an offset landing maneuver is the critical design task. Lateral axis delays appear to be more critical than longitudinal ones.

Meyer, R. T.↗

Effects of transient propellant dynamics on deployment of large liquid stages in zero-gravity with application to Shuttle/Centaur

This paper describes the application of a recently developed CFD program, HYDR-3D, to the analysis of separation of the Centaur G-Prime vehicle from the Shuttle Orbiter. The typical application presented illustrates a particularly difficult design task - deployment of a large, liquid-filled, densely packaged vehicle from a manned vehicle. Since it represents a potential catastrophic hazard, a vast number of conditions and parameters must be analyzed to ensure tolerance of at least two credible failures. Validation of the HYDR-3D program against zero- and low-gravity experimental data is also presented. Using the fluid dynamics program, this approach can be used confidently to analyze and determine design requirements for a variety of OTV/space-station deployment and docking problems.

Martin, R. E.↗

Object-Oriented Multi-Disciplinary Design, Analysis, and Optimization Tool

An Object-Oriented Optimization (O3) tool was developed that leverages existing tools and practices, and allows the easy integration and adoption of new state-of-the-art software. At the heart of the O3 tool is the Central Executive Module (CEM), which can integrate disparate software packages in a cross platform network environment so as to quickly perform optimization and design tasks in a cohesive, streamlined manner. This object-oriented framework can integrate the analysis codes for multiple disciplines instead of relying on one code to perform the analysis for all disciplines. The CEM was written in FORTRAN and the script commands for each performance index were submitted through the use of the FORTRAN Call System command. In this CEM, the user chooses an optimization methodology, defines objective and constraint functions from performance indices, and provides starting and side constraints for continuous as well as discrete design variables. The structural analysis modules such as computations of the structural weight, stress, deflection, buckling, and flutter and divergence speeds have been developed and incorporated into the O3 tool to build an object-oriented Multidisciplinary Design, Analysis, and Optimization (MDAO) tool.

Pak, Chan-gi↗

Handling Qualities Evaluations of Low Complexity Model Reference Adaptive Controllers for Reduced Pitch and Roll Damping Scenarios

National Aeronautics and Space Administration (NASA) researchers have conducted a series of flight experiments designed to study the effects of varying levels of adaptive controller complexity on the performance and handling qualities of an aircraft under various simulated failure or damage conditions. A baseline, nonlinear dynamic inversion controller was augmented with three variations of a model reference adaptive control design. The simplest design consisted of a single adaptive parameter in each of the pitch and roll axes computed using a basic gradient-based update law. A second design was built upon the first by increasing the complexity of the update law. The third and most complex design added an additional adaptive parameter to each axis. Flight tests were conducted using NASA s Full-scale Advanced Systems Testbed, a highly modified F-18 aircraft that contains a research flight control system capable of housing advanced flight controls experiments. Each controller was evaluated against a suite of simulated failures and damage ranging from destabilization of the pitch and roll axes to significant coupling between the axes. Two pilots evaluated the three adaptive controllers as well as the non-adaptive baseline controller in a variety of dynamic maneuvers and precision flying tasks designed to uncover potential deficiencies in the handling qualities of the aircraft, and adverse interactions between the pilot and the adaptive controllers. The work was completed as part of the Integrated Resilient Aircraft Control Project under NASA s Aviation Safety Program.

Hanson, Curt↗

Subsonic Ultra Green Aircraft Research: Phase IV Final Report – Volume I Mach 0.80 Transonic Truss-Braced Wing High-Speed Design Report

This design report summarizes work performed by the Boeing Subsonic Ultra-Green Aircraft Research (SUGAR) team from December 2016 through June 2018. In Phase IV of the SUGAR program, Boeing is working to improve the productivity of a TTBW configuration by updating the Mach 0.745 vehicle concept to operate efficiently at Mach 0.80. Due to the aerodynamic and structural design challenges associated with adapting the design to a higher speed, design tasks have been broken into several subtasks. The information in this report (Volume I) documents the development of a Mach 0.80 vehicle outer mold line, maturation of TTBW structural concepts, and presents a preliminary high-liftsystem assessment. Results from these studies were integrated into an aircraft-level performance code that estimates the benefits of TTBW technology, both on its own and as a part of the SUGAR integrated technology suite. The aerodynamic performance results presented herein detail the high cruise efficiency of the TTBW concept operating at M=0.80. Results from the RANS code OVERFLOW indicate that the TTBW is aerodynamically well suited for operation at the design M=0.80 transonic cruise Mach number. Aircraft-level performance predictions show that the TTBW offers a 7.2% improvement in fuel burn (per seat) for an economic mission of 900nm, and a 9.0% improvement in fuel burn (per seat) for a 3500nm mission with full passenger payload, relative to an aspect ratio 13 conventional tube and wing configuration of equivalent technology. Integration of the TTBW performance benefits into the SUGAR technology suite shows a 55.9% reduction in fuel burn (for the economic mission) relative to the reference (SUGAR Free) aircraft, which is a consistently sized traditional cantilever wing, single-aisle transport typical of the 2008 fleet. This benefit does not include the performance improvement potential of hybrid-electric systems studied in earlier phases of the SUGAR program Structural concept development work completed in Phase IV has identified several strut attachment concepts that are worth additional development activity – an inboard strut attachment swivel joint concept (which enables the strut to carry axial loads while avoiding strut bending induced by wing twist during flight) significantly simplifies the construction of the main strut. An outboard offset strut attachment concept holds significant potential for further reductions in wing-strut interference drag. Based on work performed to date on Phase IV and the previous phases of the SUGAR program, the TTBW concept continues to remain a viable concept for significantly improving the performance of future aircraft. High-fidelity aerodynamic analysis of the Mach 0.80 TTBW aircraft has shown fuel burn improvement that has exceeded initial expectations despite the increase in cruise Mach number. Structural concept maturation has continued to refine the TTBW structure, and has found no obvious ‘show-stoppers’ to date. Therefore, the potential benefit of improved performance through the use of a very high aspect ratio strut-braced wing continues to warrant additional study

SUGAR↗

Cognitive Functioning in Space Exploration Missions: A Human Requirement

Solving cognitive issues in the exploration missions will require implementing results from both Human Behavior and Performance, and Space Human Factors Engineering. Operational and research cognitive requirements need to reflect a coordinated management approach with appropriate oversight and guidance from NASA headquarters. First, this paper will discuss one proposed management method that would combine the resources of Space Medicine and Space Human Factors Engineering at JSC, other NASA agencies, the National Space Biomedical Research Institute, Wyle Labs, and other academic or industrial partners. The proposed management is based on a Human Centered Design that advocates full acceptance of the human as a system equal to other systems. Like other systems, the human is a system with many subsystems, each of which has strengths and limitations. Second, this paper will suggest ways to inform exploration policy about what is needed for optimal cognitive functioning of the astronaut crew, as well as requirements to ensure necessary assessment and intervention strategies for the human system if human limitations are reached. Assessment strategies will include clinical evaluation and fitness-to-perform evaluations. Clinical intervention tools and procedures will be available to the astronaut and space flight physician. Cognitive performance will be supported through systematic function allocation, task design, training, and scheduling. Human factors requirements and guidelines will lead to well-designed information displays and retrieval systems that reduce crew time and errors. Means of capturing process, design, and operational requirements to ensure crew performance will be discussed. Third, this paper will describe the current plan of action, and future challenges to be resolved before a lunar or Mars expedition. The presentation will include a proposed management plan for research, involvement of various organizations, and a timetable of deliverables.

Fiedler, Edan↗

Machine-learning Solution for Automatic Spacesuit Motion Recognition and Measurement from Conventional Video

Extravehicular Activity (EVA) spacesuits exhibit unique movement patterns due to their design characteristics. Mobility assessments using traditional motion capture systems are cost prohibitive and not feasible for some training conditions (e.g., simulated lunar outdoor terrain). This paper aims to present the ongoing development of machine learning solutions to quantify suit motions from conventional videos without special sensors or hardware. Preliminary work into this field was promising but given the fast growth in deep/machine learning technologies, external expertise was sought from open-source communities. Partnerships were formed with the NASA JSC Center of Excellence for Collaborative Innovation (CoCEI) and an execution crowdsourcing platform partner to solicit machine learning framework developments from external contenders. NASA provided contenders with images and video clips of spacesuits with simultaneously measured motion capture data during EVA simulation tasks. The contenders used this data to train and develop generalized algorithms to predict motions. At the end of the crowdsourcing event, the top five solutions were selected from 250 submissions. Each submission was tested and scored using video clips not previously disclosed to the contenders. The weighted scoring metrics measured how well the algorithm detected the suit shape, the 2D suit joint detection accuracy, and 3D joint detection accuracy. The winning solution was able to achieve roughly 85% prediction accuracy. Overall, the algorithms could efficiently detect various types of spacesuits and motions across different EVA environments such as the NASA Active Response Gravity Offload System (ARGOS). After continued improvements and validation, the fully developed system will enable EVA stakeholders to quantify suit kinematic patterns, which can help optimize suit, hardware, and task designs.

Linh Vu↗

B-1 AFT Nacelle Flow Visualization Study

A 2-month program was conducted to perform engineering evaluation and design tasks to prepare for visualization and photography of the airflow along the aft portion of the B-1 nacelles and nozzles during flight test. Several methods of visualizing the flow were investigated and compared with respect to cost, impact of the device on the flow patterns, suitability for use in the flight environment, and operability throughout the flight. Data were based on a literature search and discussions with the test personnel. Tufts were selected as the flow visualization device in preference to several other devices studied. A tuft installation pattern has been prepared for the right-hand aft nacelle area of B-1 air vehicle No.2. Flight research programs to develop flow visualization devices other than tufts for use in future testing are recommended. A design study was conducted to select a suitable motion picture camera, to select the camera location, and to prepare engineering drawings sufficient to permit installation of the camera. Ten locations on the air vehicle were evaluated before the selection of the location in the horizontal stabilizer actuator fairing. The considerations included cost, camera angle, available volume, environmental control, flutter impact, and interference with antennas or other instrumentation.

Celniker, Robert↗