Search NASA⌕ Search

SEARCH · Search NASA

Results for “test support”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Results of South-East Flux Trap Dosimetry Measurements for the Advanced Test Reactor Critical Facility in support of Advanced Sensors and Instrumentation Development

Reactor dosimetry measurements are commonly used to validate simulation and modeling in nuclear reactor tests. Numerous standard dosimeter materials exist which are commonly utilized with sensitivities to different energy ranges of neutrons. At the Advanced Test Reactor (ATR), cobalt alloy and pure nickel wires are installed every cycle to monitor thermal- and fast-neutron fluence rates. However, there is growing interest in exploring less commonly used materials which are either more sensitive to different parts of the neutron energy spectrum or which can incorporate multiple activation paths in a single material. Epithermal and fast-neutron energies beyond the typical 1-MeV threshold are of particular interest. Two ATR-C Flux Runs took place during 2024; each flux run included supplemental dosimetry packages in the South-East Flux Trap (SEFT) Filler. The focus of the dosimetry package for flux run 23-4 was to test two novel dosimetry methods that can provide simultaneous thermal and threshold (fast) sensitivity in a single dosimeter wire. A selection of 3% Au in Cu alloyed wires were available that provided sensitivity to fast and thermal neutrons through 5 different reactions. Likewise, Fe offers multiple interaction pathways with sensitivity to both thermal and fast neutrons. The main question to be answered by these irradiations was if sufficient radioactivation would take place in the ATR-C SEFT during a nominal 20-minute irradiation at typical power levels (near 600Wth) to observe the threshold reactions that have smaller activation cross-sections than the thermal reactions without being saturated by interfering interactions and Compton continuum during the High-Purity Germanium (HPGe) measurements. The results from comparing the measurement results to anticipated activity levels provide confidence in our ability to activate both traditional and novel dosimetry materials in ATR-C, however not all the measured values matched with the predicted activities. This leaves further room for investigation both on the experimental and computational approaches for future irradiation experiments.

46 - INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AN↗
DOE OSTI2024

Flow Sensor Test Article (F-STAr) - Water Testing and Commissioning Report for FY2024

Argonne National Laboratory’s Mechanism Engineering Test Loop (METL) facility is developing new experimental testing capabilities with the Flow Sensor Test Article (F-STAr). F-STAr’s mission is to provide high flowrate, sodium submersible testing capabilities to support the development of sodium cooled nuclear fission reactors. Figure 1 shows a model of F-STAr (left) and a photo of the partially assembled test article (right) with several of the main components labeled. The system currently includes a large pump with desired flowrates of up to 100 GPM; an immersion heater with a maximum power of 5 kW; an immersion cooler with an estimated maximum cooling power of 2 kW; and an experimental test section to support sub-test articles. Initially, F-STAr will be setup for testing flow sensors, specifically Eddy Current Flow Sensors (ECFS). However, the system can be reconfigured to support a wide range of testing needs. For example, F-STAr could be setup to complete testing of hydraulic components, heat exchangers, hydrodynamic bearings, seals, and more. This report will provide an update on the development of F-STAr with a focus on the water testing and commissioning activities during Fiscal Year 2024 (FY24). First, the report will focus on describing the pump development. Specifically, updates will be provided on troubleshooting the pump’s excessive vibrational issues. In addition to updates on the pump, pressure-flowrate performance testing in water will be described. Furthermore, updates will be provided on a pump shaft bushing development as well as rigging procedures. Future work and paths forward for F-STAr will be described. Finally, a short summary on the ECFS development will be described at the end of the report.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2021

Structural Health Monitoring: Using an Autoencoder to Identify Damage in a Bolted Joint [Capstone Project]

Los Alamos National Laboratory (LANL) is an important fixture in the United States Department of Energy’s (DOE) National Nuclear Security Agency (NNSA) complex. LANL is one of the largest national laboratories in the country, and the laboratory’s primary mission is to support the nation’s nuclear stockpile. The lab functions as a design agencies for the NNSA and performs extensive testing on weapons as part of that mission. The shock and vibration test team at LANL utilizes electrodynamic shaker systems for important qualification testing in support of the laboratory’s mission. Modern engineering relies heavily on bolted joints to connect two objects. During these shaker tests, engineers depend on bolted joints to secure the test article to a fixture and the fixture to the table. The test article may be hazardous and contain high explosives which could create a safety issue if a bolted joint failed. A loss of preload in a bolt will affect the way energy is input to the system and may introduce nonlinearities as the joint opens and closes. The loss of preload can create challenges controlling the test and make acquired signals useless. Being able to monitor preload within bolted joints during testing can improve the quality of the data and keep workers safe.

42 ENGINEERING↗
DOE OSTI2021

Modeling and Analysis for Spent Nuclear Fuel Seismic Testing

Note: This is the final public release version of PNNL-31671 Draft, which was previously released to the sponsor for review. The intent is the public release version will be PNNL-31671. There are no significant changes from the earlier draft version. This unlimited distribution report is the deliverable for M3SF-21PN010202014: Modeling and Analysis for Spent Nuclear Fuel Seismic Testing. This report summarizes the modeling, analysis, and test plan support completed by Pacific Northwest National Laboratory for the spent nuclear fuel dry storage system seismic test plan through May of 2021. Test plan preparation is planned to continue until the seismic test is completed in July of 2022. This report covers preliminary structural dynamic model development and computer-aided design of test hardware. Based on preliminary modeling, the strongest earthquakes under consideration in this test program provide mechanical loading on the spent nuclear fuel that is comparable to the 30 cm cask drop scenario, although the loads do not appear to be strong enough to cause significant permanent deformation of the fuel assembly spacer grids. The potential for grid deformation during the test will be assessed when the proposed shake table motion becomes available. The weakest earthquakes considered in this test are expected to be comparable to the mechanical loads witnessed in the multimodal transportation test of 2017. The horizontal canister system is predicted to provide nearly-uniform loading condition on the fuel assemblies it contains, while the vertical cask system is predicted to cause non-uniform dynamic loads on the fuel assemblies. In the horizontal case, gravity keeps the fuel assemblies in contact with one basket wall surface unless the loads are strong enough to cause a separation. In the vertical case, the fuel assemblies are relatively long and slender, and seismic motion in the anticipated test range is predicted to cause the assemblies to lean, tilt, and impact the basket walls throughout the seismic event. These gap closures are a nonlinear force transmission condition, so the vertical system is expected to have more variation and variability than the horizontal system. While the horizontal system is expected to have a relatively more linear response than the vertical system, there is still the potential for nonlinear behavior in the horizontal system because the fuel assemblies are free to slide, bounce, and impact the basket walls if the seismic loads are strong enough. One major conclusion of this study is that the use of mixed fuel assemblies in the canister will be acceptable. There are differences in overall system response when the mass, center of gravity, or gaps are changed, but the changes in response are within the bounds of a system that contains completely homogeneous fuel assemblies. One important observation is that the loading for each individual fuel assembly within the vertical canister is expected to be different from that of the others because of nonlinearities in the system. The horizontal canister system is expected to have a more uniform and more predictable response than the vertical canister, making variations in fuel assembly characteristics easier to account for. One important recommendation that comes from this modeling work is to repeat some of the strongest shake tests at different angles, particularly for the vertical cask system. Modeling predicts that strong seismic motion will cause the fuel assemblies to close initial gaps and impact the fuel basket walls when the canister is in the vertical cask configuration. Each shake test will impose a pre-defined three-dimensional time history on the cask system.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Establishing Maximal Core Excess Reactivity Envelope for TREAT Test Vehicle Insertion

The Transient Reactor Test (TREAT) Facility is an air-cooled reactor composed of graphite-urania fuel encapsulated in zirconium alloy canisters and surrounded by ~2 ft (~61 cm) of nuclear grade graphite. The primary role of TREAT is to provide in-pile nuclear-heated safety research via transient testing [1]. The following work represents further analyses building upon previously reported work to support larger volume test vehicles within TREAT [2]. The Broad Use Specimen Transient Experiment Rig (BUSTER) provides ample versatility for numerous transient test concepts. However, future testing and experiment needs will require testing environments of different in-core footprints. The versatility of TREAT allows for the development of variegated core layouts with key limitations emplaced as operational safety temperature restrictions and available core reactivity. The focus of this current effort is to gauge core arrangements for TREAT core loadings to support centralized experimental testing of varying dimensional capacity. The total core excess reactivity (ER) was computed for different arrangements to establish comparison tables that enable ready assessment of core ER available for future experiment concepts. Test vehicle worths would then be necessary to establish available ER to support transient testing requirements and to perform reactor performance and safety calculations [3,4].

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2020

Comparison of Light-Weight Radioisotope Heater Unit (LWRHU) Historical Testing to Special Form Testing Requirements

This paper compares the Light-Weight Radioisotope Heater Unit (LWRHU) historical testing to Department of Transportation (DOT) Special Form criteria per 49 CFR Part 173, Shippers-General Requirements for Shipments and Packages, Section 469, Tests for special form Class 7 (radioactive) materials as specified in DOE-STD-1027, Hazard Categorization of DOE Nuclear Facilities. Compliance with the aforementioned criteria allows for the exclusion of radioactive sources from the facility’s nuclear material inventory. As part of a new program at Los Alamos National Laboratory (LANL), LWRHUs are planned to be moved into TA-55, PF-5 Power Source Assembly Area (PSAA) for assembly and testing activities. The PSAA Facility is categorized as a low hazard, non-nuclear facility per DOE STD-1027 and is described in TA55-PF-5-FHC-11-001, Facility Hazard Categorization of the PSAA at PF-5, TA-55. The Facility Hazard Categorization document states, there must be documentation that radioactive sources are engineered to pass the special form testing specified by DOT in 49 CFR 173.469, Tests for special form Class 7 (radioactive) materials or ANSI N43.6, Sealed Radioactive Sources - Classification. This paper documents the extensive historical environmental safety testing of the LWRHU and demonstrates its ability to survive potential launch safety accident scenarios. The testing results are used herein to demonstrate through a comparative analysis that the robust design of the LWRHU meets or exceeds the special form testing specifications in 49 CFR 173.469, enabling the LWRHU to be transported and handled in PF-5 in support of testing and assembly program.

07 ISOTOPE AND RADIATION SOURCES↗
DOE OSTI2024

Re-assembly and test of COMB dipole magnet with STAR® wires

Fermilab is developing the Conductor on Molded Barrel (COMB) magnet technology that works well with round REBCO conductors. COMB-STAR-1 magnet based on STAR wire by AMPeers was fabricated and tested in liquid nitrogen in 2023. The magnet demonstrated >90 Ic retention in the coils (before/after winding). Even though the magnet was not originally designed for operation at lower than 77 K temperatures, it was decided to test it in liquid helium to: - check the instrumentation and the DAQ system; - check the ability to detect resistive transitions or quenches and to protect the magnet; - gather the information on possible magnet design chances and upgrades of the test facility for future testing of HTS magnets. The magnet was re-assembled with a larger iron yoke and the axial supports and tested in liquid helium in 2024 at Fermilab s Vertical Magnet Test Facility (VMTF). It was the first HTS magnet test at that facility ever.

Kashikhin, Vadim↗
DOE OSTI2020

Testing of Crystalline Silicotitanate to Support Tank-Side Cesium Removal System Operations - 20458

The direct feed of waste from the Hanford tank farms to the Low-Activity Waste Facility at the Hanford Waste Treatment and Immobilization Plant requires an intermediate treatment step that prepares the waste for vitrification. Washington River Protection Solutions (WRPS) selected a near-tank treatment system known as the Tank-Side Cesium Removal (TSCR) system to perform the required intermediate treatment functions. The approach in the TSCR system is to filter waste supernatant with a sintered metal dead-end filter and then use a series of ion exchange columns to remove cesium; this system has several similarities to the Tank Closure Cesium Removal system that has been deployed on the Savannah River Site. The ion exchange media proposed for use is crystalline silicotitanate (CST), which is a non-elutable media with a high affinity for cesium. Because the media is non-elutable, loaded columns will be blown down with compressed air, moved into interim storage, and replaced with new columns when cesium capacity is reached. The assumed extent and rate of drying that could be achieved in the TSCR column geometry lacked confirmation by experimental data. In addition, once the columns are loaded with cesium, they generate flammable gases (primarily hydrogen) via radiolysis acting on any resident liquids, i.e., moisture, remaining in the media bed. An assessment of available information on CST concluded that gas generation data that bounds expected operational conditions were needed to support the TSCR system safety basis and planned operations. Working with WRPS, Pacific Northwest National Laboratory (PNNL) designed and conducted testing with CST media to address the need for (a) representative in-column drying data, and (b) bounding flammable gas generation data. Drying testing was performed using a full-height column with a diameter of approximately 2 inches with injected air at temperatures of 18 deg. C and 30 deg. C. Gas generation testing was conducted in an engineered bunker that allowed simultaneous irradiation of up to eight samples at a time. These two experimental approaches used at PNNL for the CST testing are summarized and the major outcomes are presented. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

Integrated Renewable Combined Heat and Power for Ethanol

Conference presentation at 48th International Technical Conference on Clean Energy (Clearwater Clean Energy Conference), Clearwater, Florida, June 16–19, 2024. This project evaluates the technical and economic feasibility of small‑scale combined heat and power (CHP) systems using corn stover to support bioenergy with carbon capture and storage (BECCS) at ethanol facilities. The work includes resource characterization, pilot‑scale gasification and CO 2 capture testing to support techno‑economic analysis, economic evaluation of CHP deployment and potential carbon revenue, and life‑cycle assessment of gasification‑based CHP systems.

09 BIOMASS FUELS↗
DOE OSTI2023

A Power Takeoff Device for a Small Marine Hydrokinetic Turbine Deployed from an Unmanned Floating Platform

The design, development, and field-testing of a power takeoff (PTO) device equipped with a ball-type continuously-variable transmission (B-CVT) for a small marine hydrokinetic (MHK) turbine deployed from a floating unmanned autonomous mobile catamaran platform is described. The turbine is a partially-submerged multi-blade undershot waterwheel (USWW). The objective is to develop a PTO for the optimal conversion of the MHK energy harnessed by the turbine to electric power, which is stored in battery banks onboard the MHK platform. Modeling, simulation, and bench testing of the USWW and PTO show the feasibility of utilizing the B-CVT's variable gear ratio to decouple the USWW and generator speeds, maintaining the waterwheel within its optimal tip speed ratio (TSR) while varying the generator speed, thereby increasing the efficiency of the PTO. Results of bench and field testing in support of characterizing the power conversion capabilities of the PTO are described. The system being developed is in support of potential self-powered autonomous mobile recharge stations for unmanned aerial vehicles (U A V s) operating in coastal zones. Field tests of the complete MHK platform with 9 blades on the waterwheel and wheel sub mergences of 10 and 12 inches (full blade submergence) were performed. The overall proof-of-concept was successfully demonstrated, with the system satisfactorily capturing and converting water flow energy into electricity. The feasibility of utilizing the B-CVT as a means of increasing the PTO power capture capabilities and efficiency is analyzed.

Pimentel, Hugo↗
DOE OSTI2024

Advanced Functional Membranes for Noble Gas Management: Fabrication and Testing of Membranes on Porous Support

We selected several porous materials including PNW-24, CC3, SAPO-34, SAPO-56 and PNW-6, as the basis for fabricating membranes for Kr/Xe separation. Initially, we synthesized powder samples of the candidates and confirmed their crystallinity and morphology with X-ray diffraction and microscopy. In the case of PNW-24 and PNW-6, we further confirmed its Xe selectivity through Xe and Kr adsorption experiments, while we relied on literature reports for CC3, SAPO-34 and SAPO-56. We subsequently proceeded to fabricate membranes on porous alumina supports using techniques such as seeded-assisted secondary growth, in-situ growth and solution-processed method. PXRD on the membranes verified that the structures were well-grown on the surface of alumina support, while SEM provided visual confirmation of particle morphology. Importantly, defects were not visually observed in the fabricated membranes, which was further verified with pressure retention tests. We analyzed the separation performance of the synthesized membranes using a dilute gas mixture comprising of xenon, krypton and argon. We focused on PNW-6 to optimize the synthesis reaction time and study the effects of time on gas separation. While more research is necessary to reach a comprehensive conclusion, in alignment with our milestones, we have successfully achieved our goals.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Improved Verification and Validation Testing and Tools [Slides]

All MCNP team supported V&V test suites are now developed in a separate repository from the MCNP source code within a Python-based framework. This entire framework will be distributed with the upcoming MCNP6.3 release. Most V&V test suites distributed with MCNP6.2 will be distributed in new framework. New V&V test suites are done or being worked on for the MCNP6.3 release.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2025

Experimental Validation of a High-Temperature Test Facility for Future Additive Manufactured Supercritical Carbon Dioxide Turbine Testing

For next-generation power plants to achieve high cycle efficiencies consistent with the Department of Energy's 65% efficiency target, turbomachinery capable of operating within high-temperature power cycles must be demonstrated. Pairing additively manufactured superalloy turbines with the supercritical carbon dioxide (sCO 2 ) power cycle could enable turbine inlet temperatures approaching 1300 °C while providing flexibility in turbine cooling strategies. Development of test facilities to characterize and validate such systems is crucial. In this study, a turbine test facility capable of achieving inlet conditions of 800 °C, 11 MPa, and 0.43 kg/s while accommodating complex auxiliary cooling flow requirements has been designed and constructed to support future testing of a Haynes 282 additively manufactured 30 kW turbine-generator system with advanced cooling channels. This facility enables characterization of aerodynamic performance, leakage, and windage losses. Details of the facility's construction and operation are presented, along with experimental validation tests using an orifice as an expansion device in place of the turbine. These tests confirm that the facility can reach the required conditions, distinguish regions of achievable steady and pseudo-steady conditions, and identify the heater power required for each point in the upcoming turbine campaign. The campaign confirmed that ISO 5167-2 can reliably predict orifice mass flow rates in extreme supercritical carbon dioxide conditions with deviations of 0.5–7.5%.

42 ENGINEERING↗
DOE OSTI2025

Nuclear Thermal Rocket Emulator for a Hardware-in-the-Loop Test Bed

To support NASA’s mission to use nuclear thermal rockets for future Mars missions, an instrumentation and control test bed has been built at Oak Ridge National Laboratory. The system is designed as a hardware-in-the-loop test bed for testing control elements and autonomous control algorithms for nuclear thermal propulsion rockets. The mock reactor system consists of a modular and scalable framework, using inexpensive components and open-source software. The hardware system consists of a two-phase flow loop and a mock reactor with six control drums. A single-board computer (NVIDIA Jetson) handles reactor core emulation and hosts a message queuing telemetry transport broker that allows user-deployed control algorithms to interact with the system hardware. The reactor emulator receives sensor data from the hardware and provides the simulated performance of the reactor under steady-state, transient, and fault conditions. The emulator uses a reactivity lookup table and the point kinetics equations to solve for the reactor dynamics in real time. Emulated reactor dynamics and sensor input inform the autonomous control algorithm’s decision-making in a closed-loop manner. The current system is capable of operating at 10 Hz, but faster cycle rates are an area of ongoing research. This test bed will enable NASA and other space vendors to rigorously test their autonomous control systems for NTP rockets under transient (reactor startup and shutdown), steady-state, and fault conditions to reduce development time and risk for autonomous control systems in future missions.

autonomous control↗
DOE OSTI2022

DESIGN AND TESTING OF A 275 BAR 700 DEGREE CELSIUS EXPANDER FOR AN INTEGRALLY GEARED SUPERCRITICAL CO2 COMPANDER

An integrally-geared (IG) compressor-expander (compander) for use in a nominal 10 MW-scale concentrated solar power (CSP) supercritical carbon dioxide (sCO2) plant application was designed, manufactured, and tested. The integrally-geared compander (IGC) developed for this application comprises multiple pinion shafts interacting through a single bull gear to create a compact package and utilize a lowcost, low-speed driver. The present work will detail the design of the high-pressure high-temperature expander casing on an integrally geared frame, and illustrate how the project successfully mitigated the risk of fatigue and creep while allowing for rapid thermal transients in the design. Furthermore, test data from the test campaign will be presented supporting the analysis. Test results also show temperature profiles during operation exceeding 720° Celsius.

wilkes, jason↗
DOE OSTI2024

FUEL PERFORMANCE STUDIES AT IDAHO NATIONAL LABORATORY MAKING USE OF THE BYRON FUEL SHIPMENT

In December of 2023 a shipment of commercially irradiated fuel rods from the Byron Generating Station in Illinois was successfully shipped to the Materials and Fuels Complex (MFC) at Idaho National Laboratory (INL). The make-up of the rods includes a mix of cladding types from traditional ZirloTM, advanced zirconium alloys, and chrome coated ZirloTM. Burnups range from regular end of life values to over 70 GWd/MTU rod average. The R&D plan for the rods involves multiple projects from developing licensing data for new claddings to integral transient tests to support burnup extension efforts in the United States. The R&D began in early 2024 with the nondestructive examinations of the rods after which they will be sectioned for microscopy, mechanical testing, and analytical chemistry. Additionally, many rod segments will be refabricated into new test pins and inserted into a static water capsule for integral Reactivity Initiated Accident (RIA) and Loss of Coolant Accident (LOCA) testing at the TREAT reactor.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Comparative post-irradiation examination of high burnup U-19Pu-10Zr: Assessing steady-state irradiation behavior against historical and modeled fuel performance

Here, the development of next-generation sodium-cooled fast reactors necessitates comprehensive research on metallic fuels to maximize economic performance while ensuring safe operation. In this study, we investigated the steady-state irradiation behavior of two high burnup U-19Pu-10Zr fuel pins, DP-36 and DP-40, in preparation for planned safety testing. Post-irradiation examination (PIE) was performed to quantify fuel column elongation, regions of low-density at the top of the fuel column, pin deformation, fission product distribution, fractional fission gas release, microstructural evolution, and fuel constituent redistribution. Benchmarking against existing PIE data from U-19Pu-10Zr fuel pins irradiated in EBR-II revealed consistent patterns in fuel column elongation and cladding diametral strain. However, both pins exhibited longer low-density structures, and destructive examination of DP-36 revealed more complex constituent redistribution patterns compared to previously reported data for ternary fuel pins. The steady-state irradiation of both pins was also modeled using BISON. Comparisons of PIE results with modeled predictions showed overall agreement in fractional fission gas release but consistent overestimation of axial and radial swelling due to gaseous and solid swelling models. These findings underscore the critical importance of pre-test characterization on test and sibling pins to accurately capture steady-state fuel behavior ahead of transient testing, thus establishing a baseline for post-test comparison. Additionally, these analyses identified key data gaps that warrant further investigation to improve the understanding and prediction of fuel swelling, thereby enhancing the synergy between modeling and experimental efforts in supporting accident testing.

BISON↗
DOE OSTI2021

Development of phenomena identification and ranking table for Westinghouse lead fast reactor’s safety

The Westinghouse Lead-cooled Fast Reactor (LFR) is a medium-size, passively safe, economic, Gen-IV nuclear reactor. An important effort within the Westinghouse LFR program is the development of the safety analysis methodology, which comprises computer code development, model development, and experimental testing. A key initial task associated with the development of the safety analysis methodology is the identification of processes and phenomena that affect the plant's capability to meet selected safety performance indicators. This is accomplished through the development of a Phenomena Identification and Ranking Table (PIRT) for selected accident scenarios which, for this specific PIRT effort, included selected postulated design basis accidents and hypothetical beyond design basis accidents in LFRs. This paper describes the role of PIRT in the development of the Westinghouse LFR safety analysis methodology and the process used in the PIRT development. Specifically, the Westinghouse LFR PIRT assessed importance of pertinent phenomena and identified gaps in their knowledge-base by evaluating current modeling capabilities and data available for validation. The ultimate goal was to provide guidance on computer code development and validation efforts and to prioritize testing to support LFR design and licensing. The key phenomena and processes that are deemed highly important for the safety performance indicators, but for which the state of knowledge is low, are presented. The testing program and analyses development are planned to address significant phenomena in the PIRT.

Lead fast reactor↗