Results for “tractor” — Page 6

NASA NTRS1987

Predictions of wing and pylon forces caused by propeller installation

Replacement of current turbojets by high-efficiency unducted propfans could have the unfortunate side effect of increasing cabin noise, essentially because unsteady-aerodynamic mechanisms are likely to be introduced whereby some of the energy saved may be lost again, to the production of propeller noise and to wing/pylon vibrations coupling to the cabin as a sounding board. The present study estimates theoretically associated harmonic aerodynamic forces for two candidate configurations: a pusher propeller which chops through the mean wake of the pylon supporting it, and in the process generates a blade-rate force driving the structure, and a tractor wing-mounted propeller, whose trailing rotating wake induces an unsteady downwash field generating unsteady wing airloads. Reported predictions of such propfan aerodynamic sources of structure-borne sound, or vibration, could be the basis for devising means for their mechanical isolation, and thus for the effective interruption of the structural noise path into the cabin. Both mechanisms are analyzed taking advantage of the high subsonic Mach number and high reduced frequency of the interaction between the impinging flow and the affected aerodynamic element.

Martinez, Rudolph↗

NASA NTRS1986

Installation aerodynamics of wing-mounted, single-rotation propfans

The installation of advanced (M = 0.8) turboprop propulsion systems on transport aircraft represents a challenging task to design engineers. The installation aerodynamics of wing-mounted, single-rotation, tractor turboprop systems have been extensively investigated by NASA Ames using a large powered semispan wind tunnel model. Two configurations have been studied: a straight under-the-wing (UTW) nacelle and a contoured over-the-wing (OTW) configuration. The installation characteristics of these two configurations are presented in terms of installed drag, wing pressure distributions, and surface oil flows. Through the use of wing leading-edge modifications, the installed drag of the UTW nacelle was reduced to less than isolated nacelle drag at the cruise condition of M = 0.8 with a wing C(L) of 0.5. At this condition, the favorable interference is attributed to the recovery of a portion of the swirl in the slipstream generated by the single rotation propeller. The OTW installation represented a much more difficult task. For the configuration tested, the installed drag was unacceptably high and demonstrated the sensitive nature of installing a nacelle/slipstream combination in the transonic flow regime.

Bencze, Daniel P.↗

NASA NTRS1986

High speed wind tunnel tests of the PTA aircraft

Propfans, advanced highly-loaded propellers, are proposed to power transport aircraft that cruise at high subsonic speeds, giving significant fuel savings over the equivalent turbofan-powered aircraft. NASA is currently sponsoring the Propfan Test Assessment Program (PTA) to provide basic data on the structural integrity and acoustic performance of the propfan. The program involves installation design, wind-tunnel tests, and flight tests of the Hamilton Standard SR-7 propfan in a wing-mount tractor installation on the Gulfstream II aircraft. This paper reports on the high-speed wind-tunnel tests and presents the computational aerodynamic methods that were employed in the analyses, design, and evaluation of the configuration. In spite of the complexity of the configuration, these methods provide aerodynamic predictions which are in excellent agreement with wind-tunnel data.

Aljabri, A. S.↗

NASA NTRS1987

Results of acoustic tests of a Prop-Fan model

Results of acoustic tests in a low speed open jet anechoic wind tunnel are presented for a counter rotation Prop-Fan model. The model tested had 5 front and 5 rear rotor blades with swept planform. Noise spectra are presented showing the influence of operating and configuration variables such as: (1) power absorption, (2) tip speed, (3) rotor-rotor spacing, (4) power split between the front and rear blade rows, (5) variation of the RPM ratio between front and rear blade rows, (6) tractor versus pusher (pylon effects), and (7) angle of attack. In addition to model scale results, calculated levels derived from test are presented showing the influence of the above variables on Effective Perceived Noise Level of a 13.1 ft diameter Prop-Fan at a flyover distance of 1500 ft. It was found that the strongest effects are caused by tip speed and power absorption. A significant finding was that there is an optimum operating tip speed for minimum noise for a given power absorption. Effects of other parametric variations are generally small but measurable. In order to minimize noise to meet airplane certification limits, operation at moderate tip speeds and power absorption is shown to be desirable. Accuracy of predicted Effective Perceived Noise Level is shown to be good with the best accuracy in the 590 to 670 ft/sec tip speed range.

Metzger, F.B.↗

NASA NTRS1987

Advanced turboprop wing installation effects measured by unsteady blade pressure and noise

A single rotation model propeller (SR-7A) was tested at simulated takeoff/approach conditions (Mach 0.2), in the NASA Lewis 9- by 15-Ft Anechoic Wind Tunnel. Both unsteady blade surface pressures and noise measurements were made for a tractor configuration with propeller/straight wing and propeller alone configurations. The angle between the wing chord and propeller axis (droop angle) was varied along with the wing angle of attack to determine the effects on noise and unsteady loading. A method was developed that uses unsteady blade pressure measurements to provide a quantitative indication of propeller inflow conditions, at least for a uniform (across the propeller disk) inflow angle. The wing installation caused a nearly uniform upwash at the propeller inlet as evidenced by the domination of the pressure spectra by the first shaft order. This inflow angle increased at a rate of almost 150 percent of that of the wing angle-of-attack for a propeller-wing spacing of 0.54 wing chords at a constant droop angle. The flyover noise, as measured by the maximum blade passing frequency level, correlates closely with the propeller inflow angle (approx. 0.6 dB per degree of inflow angle) for all droop angles and wing angles of attack tested, including the propeller alone data. Large changes in the unsteady pressure responses on the suction surface of the blade were observed as the advance ratio was varied. The presence of a leading edge vortex may explain this behavior since changes in the location of this vortex would change with loading (advance ratio).

Heidelberg, Laurence J.↗

NASA NTRS1986

Preliminary aerodynamic design considerations for advanced laminar flow aircraft configurations

Modern composite manufacturing methods have provided the opportunity for smooth surfaces that can sustain large regions of natural laminar flow (NLF) boundary layer behavior and have stimulated interest in developing advanced NLF airfoils and improved aircraft designs. Some of the preliminary results obtained in exploratory research investigations on advanced aircraft configurations at the NASA Langley Research Center are discussed. Results of the initial studies have shown that the aerodynamic effects of configuration variables such as canard/wing arrangements, airfoils, and pusher-type and tractor-type propeller installations can be particularly significant at high angles of attack. Flow field interactions between aircraft components were shown to produce undesirable aerodynamic effects on a wing behind a heavily loaded canard, and the use of properly designed wing leading-edge modifications, such as a leading-edge droop, offset the undesirable aerodynamic effects by delaying wing stall and providing increased stall/spin resistance with minimum degradation of laminar flow behavior.

Johnson, Joseph L., Jr.↗

NASA NTRS1987

Advanced turboprop wing installation effects measured by unsteady blade pressure and noise

A single rotation model propeller (SR-7A) was tested at simulated takeoff/approach conditions (Mach 0.2), in the NASA Lewis 9- by 15-Ft Anechoic Wind Tunnel. Both unsteady blade surface pressures and noise measurements were made for a tractor configuration with propeller/straight wing and propeller alone configurations. The angle between the wing chord and propeller axis (droop angle) was varied along with the wing angle of attack to determine the effects on noise and unsteady loading. A method was developed that uses unsteady blade pressure measurements to provide a quantitative indication of propeller inflow conditions, at least for a uniform (across the propeller disk) inflow angle. The wing installation caused a nearly uniform upwash at the propeller inlet as evidenced by the domination of the pressure spectra by the first shaft order. This inflow angle increased at a rate of almost 150 percent of that of the wing angle-of-attack for a propeller-wing spacing of 0.54 wing chords at a constant droop angle. The flyover noise, as measured by the maximum blade passing frequency level, correlates closely with the propeller inflow angle (approx. 0.6 dB per degree of inflow angle) for all droop angles and wing angles of attack tested, including the propeller alone data. Large changes in the unsteady pressure responses on the suction surface of the blade were observed as the advance ratio was varied. The presence of a leading edge vortex may explain this behavior since changes in the location of this vortex would change with loading (advance ratio).

Heidelberg, Laurence J.↗

NASA NTRS1987

All-theoretical prediction of cabin noise due to impingement of propeller vortices on a wing structure

Reported calculations of structure-borne cabin noise for a small twin engine aircraft powered by tractor propellers rely on the following three-stage methodological breakup of the problem: (1) the unsteady-aerodynamic prediction of wing lift harmonics caused by the whipping action of the vortex system trailed from each propeller; (2) the associated wing/fuselage structural response; (3) the cabin noise field for the computed wall vibration. The first part--the estimate of airloads--skirts a full-fledged aeroelastic situation by assuming the wing to be fixed in space while cancelling the downwash field of the cutting vortices. The model is based on an approximate high-frequency lifting-surface theory justified by the blade rate and flight Mach number of application. Its results drive a finite-element representation of the wing accounting for upper and lower skin surfaces, spars, ribs, and the presence of fuel. The fuselage, modeled as a frame-stiffened cylindrical shell, is bolted to the wing.

Martinez, R.↗

NASA NTRS1988

Aerodynamic interaction between propellers and wings

A combined computational/experimental investigation has been conducted to determine the time-averaged interactive performance of a propeller and wing in tractor configuration at Mach 0.1 and Re=470,000, based on a wind tunnel model wing chord of 8 in. Wing angle-of-attack was varied from 0 to +13 deg, and propeller advance ratio ranged from 2.4 (windmilling) to 1.1 (maximum power). Both a semiempirical model and a vortex lattice simulation were used in the computational analysis. Good agreement has been obtained between theory and experiment.

Witkowski, David↗

NASA NTRS1985

A performance and reliability model for thermal barrier coatings

A modeling technique for predicting the performance and reliability of TBC's is being developed at Solar Turbines Incorporated. The concept combines experimental coating property data with finite element analyses to predict the thermal and mechanical behavior of coating systems in service. A key feature of Solar's approach is the use of a four point flexure test to estimate coating strength distributions and to predict coating failure probability. This model was used to evaluate the effect of physical variations on coating performance in high heat flux rocket engine applications for NASA. Current work, promoted by Caterpillar Tractor Company for diesel engine applications, is being conducted to measure coating strength as a function of temperature, and future work will document strength degradation with time at temperature. Solar's interest lies in the application of TBCs to gas turbine engine components.

Batakis, A. P.↗

NASA NTRS1988

A manned lunar outpost. Design considerations for three key elements in an initial manned lunar outpost

The Initial Manned Lunar Outpost (IMLO) is proposed as the initial permanent base for manned activities on the Moon. The study concentrated on identifying the equipment, support systems, and initial base configuration necessary to accomplish the various science, industrial and exploration activities planned. The primary concepts of the MLO were the use of hard modules for habitation areas creating a flexible, modular transportation system; designing a multi-functional vehicle; and using an overhead radiation protection system. The transportation system, dubbed the Lunar Mobile Surface Transport System (LMSTS), carries the hard modules to the surface of the moon and provides a method to move them to the desired location through the use of interchangeable pallets. The avionics pallets are changed-out with wheel and hitch pallets, transforming the LMSTS into a "tractor trailer" used with the Multi-Functional Vehicle (MFV). The modules are placed under the Regolith Support Structure (RSS) which provides a stable environment and radiation protection for the entire base. The overhead structure was chosen over simply burying the modules to provide a study on the advantages and disadvantages of this type of system. The advantages include easy access to the exterior of the modules, providing a protected area for vehicles and equipment used in EVA, and creating an area of constant temperature. Disadvantages include a need for prefabrication of structural components, including the preconstruction and construction phases of the initial MLO. The design approach taken considered existing and near-term materials and technology only, without the consideration of possible future building technologies.

Bell, Larry↗

NASA NTRS1989

Structural tailoring of counter rotation propfans

The STAT program was designed for the optimization of single rotation, tractor propfan designs. New propfan designs, however, generally consist of two counter rotating propfan rotors. STAT is constructed to contain two levels of analysis. An interior loop, consisting of accurate, efficient approximate analyses, is used to perform the primary propfan optimization. Once an optimum design has been obtained, a series of refined analyses are conducted. These analyses, while too computer time expensive for the optimization loop, are of sufficient accuracy to validate the optimized design. Should the design prove to be unacceptable, provisions are made for recalibration of the approximate analyses, for subsequent reoptimization.

Brown, Kenneth W.↗

NASA NTRS1989

Near-field acoustic characteristics of a single-rotor propfan

The near-field noise characteristics of the SR-7L, an eight-blade, single-rotor, wing-mounted, tractor propfan have been determined. It is found that the noise is dominated by discrete tones, usually at the first order (and occasionally at the second or third order) of the blade-passage frequency. The highest noise levels were noted at conditions of high tip helical speeds and high dynamic pressures.

Bartel, H. W.↗

NASA NTRS1986

Analysis of results from wind tunnel tests of inlets for an advanced turboprop nacelle installation

Inlets for tractor installations of advanced turboprop propulsion systems were tested in three phases, covering a period from November, 1982 to January, 1984. Nacelle inlet configuration types included single scoop, twin scoop, and annular arrangements. Tests were performed with and without boundary layer diverters and several different diverter heights were tested for the single scoop inlet. This same inlet was also tested at two different axial positions. Test Mach numbers ranged from Mach 0.20 to 0.80. Types of data taken were: (1) internal and external pressures, including inlet throat recoveries; (2) balance forces, including thrust-minus-drag; and (3) propellar blade stresses.

Hancock, J. P.↗

NASA NTRS1988

Large-scale Advanced Prop-fan (LAP) high speed wind tunnel test report

High Speed Wind Tunnel testing of the SR-7L Large Scale Advanced Prop-Fan (LAP) is reported. The LAP is a 2.74 meter (9.0 ft) diameter, 8-bladed tractor type rated for 4475 KW (6000 SHP) at 1698 rpm. It was designated and built by Hamilton Standard under contract to the NASA Lewis Research Center. The LAP employs thin swept blades to provide efficient propulsion at flight speeds up to Mach .85. Testing was conducted in the ONERA S1-MA Atmospheric Wind Tunnel in Modane, France. The test objectives were to confirm that the LAP is free from high speed classical flutter, determine the structural and aerodynamic response to angular inflow, measure blade surface pressures (static and dynamic) and evaluate the aerodynamic performance at various blade angles, rotational speeds and Mach numbers. The measured structural and aerodynamic performance of the LAP correlated well with analytical predictions thereby providing confidence in the computer prediction codes used for the design. There were no signs of classical flutter throughout all phases of the test up to and including the 0.84 maximum Mach number achieved. Steady and unsteady blade surface pressures were successfully measured for a wide range of Mach numbers, inflow angles, rotational speeds and blade angles. No barriers were discovered that would prevent proceeding with the PTA (Prop-Fan Test Assessment) Flight Test Program scheduled for early 1987.

Campbell, William A.↗

NASA NTRS1990

Aeroacoustics of advanced propellers

The aeroacoustics of advanced, high speed propellers (propfans) are reviewed from the perspective of NASA research conducted in support of the Advanced Turboprop Program. Aerodynamic and acoustic components of prediction methods for near and far field noise are summarized for both single and counterrotation propellers in uninstalled and configurations. Experimental results from tests at both takeoff/approach and cruise conditions are reviewed with emphasis on: (1) single and counterrotation model tests in the NASA Lewis 9 by 15 (low speed) and 8 by 6 (high speed) wind tunnels, and (2) full scale flight tests of a 9 ft (2.74 m) diameter single rotation wing mounted tractor and a 11.7 ft (3.57 m) diameter counterrotation aft mounted pusher propeller. Comparisons of model data projected to flight with full scale flight data show good agreement validating the scale model wind tunnel approach. Likewise, comparisons of measured and predicted noise level show excellent agreement for both single and counterrotation propellers. Progress in describing angle of attack and installation effects is also summarized. Finally, the aeroacoustic issues associated with ducted propellers (very high bypass fans) are discussed.

Groeneweg, John F.↗

NASA NTRS1990

Aeroacoustics of advanced propellers

The aeroacoustics of advanced, high speed propellers (propfans) are reviewed from the perspective of NASA research conducted in support of the Advanced Turboprop Program. Aerodynamic and acoustic components of prediction methods for near and far field noise are summarized for both single and counterrotation propellers in uninstalled and configurations. Experimental results from tests at both takeoff/approach and cruise conditions are reviewed with emphasis on: (1) single and counterrotation model tests in the NASA Lewis 9 by 15 (low speed) and 8 by 6 (high speed) wind tunnels, and (2) full scale flight tests of a 9 ft (2.74 m) diameter single rotation wing mounted tractor and a 11.7 ft (3.57 m) diameter counterrotation aft mounted pusher propeller. Comparisons of model data projected to flight with full scale flight data show good agreement validating the scale model wind tunnel approach. Likewise, comparisons of measured and predicted noise level show excellent agreement for both single and counterrotation propellers. Progress in describing angle of attack and installation effects is also summarized. Finally, the aeroacoustic issues associated with ducted propellers (very high bypass fans) are discussed.

Groeneweg, John F.↗

NASA NTRS1991

Experimental results of a propeller/wing interaction study

Steady state measurements have been performed on a propellar and a wing in a tractor configuration, to investigate the consequences of mutual interference on overall performance. For certain geometries wing lift is found to be enhanced, and wing drag to be decreased. The unsteady nature of the propeller-wing aerodynamic interaction has been studied using flow visualization. Results obtained indicate that the tip vortex is severed at the wing leading edge, the severed tip vortex filaments shear in a spanwise direction relative to one another, and these displaced filaments deform to reconnect at the trailing edge.

Johnson, Robert T.↗