Search NASA⌕ Search

SEARCH · Search NASA

Results for “unidirectional rates”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

A new test machine for measuring friction and wear in controlled atmospheres to 1200 C

This paper describes a new high temperature friction and wear test apparatus (tribometer) at NASA Lewis Research Center, Cleveland, Ohio. The tribometer can be used as a pin-on-disk or pin-on-ring configuration and is specially designed to measure the tribological properties of ceramics and high temperature metallic alloys from room temperature to 1200 C. Sliding mode can be selected to be either unidirectional at velocities up to 22 m/sec or oscillating at frequencies up 4.5 Hz and amplitudes up to + or - 60 deg. The test atmosphere is established by a controlled flow rate of a purge gas. All components within the test chamber are compatible with oxidizing, inert, or reducing gases.

Sliney, Harold E.↗
NASA NTRS1995

Processing and properties of fiber reinforced polymeric matrix composites: I. IM7/LARC(TM)-PETI-7 polyimide composites

A phenylethynyl terminated imide oligomer formed from the reaction of benzophenone tetracarboxylic acid dianhydride, an 75:25 molar ratio of 4,4'-oxydianiline and meta-phenylenediamine and 4-phenylethynylphthalic anhydride as the endcapper at a theoretical number average molecular weight (Mn) of approximately 3,700 g/mol was evaluated as a composite resin matrix. A glass transition temperature (Tg) of 315 deg C was reached after 250 deg C/1 hr annealing of the matrix resin. Unidirectional prepreg was made by coating an N-methylpyrrolidinone solution of the amide acid oligomer onto unsized IM7 graphite fibers. The thermal and rheological properties and the solvent/volatile depletion rates of the amide acid/NMP system were determined. This information was used to successfully design a molding cycle for composite fabrication. Composites molded under 800 Psi at 371 C consistently yielded good consolidation as measured by C-scan and optical photomicrography. The composite's short beam shear strength (SBS), longitudinal and transverse flexural strengths and moduli were measured at various temperatures. These composites exhibited excellent room temperature (RT) longitudinal flexural strength and modulus and RT SBS strength retention at 177 C.

Hou, Tan-Hung↗
NASA NTRS2001

Durability Evaluation of Selected Solid Lubricating Films

An investigation was conducted to examine the coefficients of friction, wear rates, and durability of bonded molybdenum disulfide (MoS2), magnetron-sputtered MoS2, ion-plated silver, ion-plated lead, magnetron-sputtered diamondlike carbon (MS DLC), and plasma-assisted, chemical-vapor-deposited DLC (PACVD DLC) films in sliding contact with 6-mm-diameter AISI 440C stainless steel balls. Unidirectional ball-on-disk sliding friction experiments were conducted with a load of 5.9 N and a sliding velocity of 0.2 m/s at room temperature in three environments: ultrahigh vacuum (vacuum pressure, 7 x 10(exp -7) Pa), humid air (relative humidity, approx. 20 percent), and dry nitrogen (relative humidity, less than 1 percent). The main criteria for judging the performance of the solid lubricating films were coefficient of friction and wear rate, which had to be less than 0.3 and on the order of 10(exp -6) cu mm/N.m or less, respectively. The bonded MoS2 and magnetron-sputtered MoS2 films met the criteria in all three environments. The ion-plated lead and silver films met the criteria only in ultrahigh vacuum but failed in humid air and in dry nitrogen. The MS DLC and PACVD DLC films met the requirements in humid air and dry nitrogen but failed in ultrahigh vacuum.

Miyoshi, Kazuhisa↗
NASA NTRS1972

Response of trapped particles to a collapsing dipole moment.

Particle motion in the secularly varying geomagnetic field is investigated in terms of a dipolar magnetic field with decreasing magnetic moment M. For dM/dt equal to the rate of decay of the earth's dipole component, we find there is drift in B-L space, resulting in an inward drift of particles accompanied with increased energy and unidirectional intensity. Secular variation of the geomagnetic field appears to be a dominant mechanism for radial drift in the inner radiation belt.

Heckman, H. H.↗
NASA NTRS1991

A new test machine for measuring friction and wear in controlled atmospheres to 1200 C

This paper describes a new high-temperature friction and wear test apparatus (tribometer). The tribometer can be used as a pin-on-disk or pin-on-ring configuration and is specially designed to measure the tribological properties of ceramics and high temperature metallic alloys from room temperature to 1200 C. Sliding mode can be selected to be either unidirectional at velocities up to 22 m/sec or oscillating at frequencies up to 4.6 Hz and amplitudes up to + or - 60 deg. The test atmosphere is established by a controlled flow rate of a purge gas. All components within the test chamber are compatible with oxidizing, inert or reducing gases.

Sliney, Harold E.↗
NASA NTRS1997

Computational Simulation of Composite Behavior

Composite microfracture technique developed here is based on the concept of global strain energy release rate. Step-by-step procedures were outlined to evaluate composite microfracture. The technique can predict microfracture initiation/propagation, predict the "structural fracture toughness", and establish the hierarchy of fracture modes. Both unidirectional and cross-ply metal-matrix composite laminates were evaluated for microfracture, subjected to thermal and mechanical loads. Five NASA reports were published as shown in the bibliography and several presentations were made at the technical conferences/ symposia. Work was also performed to develop simplified micromechanics and macromechanics for ceramic matrix composites. A novel fiber sub-structuring technique was developed, which divides the fiber into several "slices" and applies the micromechanics equation at the "slice" level, which are then integrated upwards to get the ply and the laminate properties. It allows for a more accurate representation of interfacial conditions such as partial interface bond etc. It also predicts the stress-strain behavior of a composite up to failure by taking into account material properties dependence upon temperature as well as stress redistribution that occurs due to damage initiation and propagation. A computer code CEMCAN (Ceramic Matrix Composites Analyzer) which includes all these capabilities has been developed as a part of this research activity.

Keith, Theo G., Jr.↗
NASA NTRS1986

Effect of adherend thickness and mixed mode loading on debond growth in adhesively bonded composite joints

Symmetric and unsymmetric double cantilever beam (DCB) specimens were tested and analyzed to assess the effect of: (1) adherend thickness, and (2) a predominantly mode I mixed mode loading on cyclic debond growth and static fracture toughness. The specimens were made of unidirectional composite (T300/5208) adherends bonded together with EC3445 structural adhesive. The thickness was 8, 16, or 24 plies. The experimental results indicated that the static fracture toughness increases and the cyclic debond growth rate decreases with increasing adherend thickness. This behavior was related to the length of the plastic zone ahead of the debond tip. For the symmetric DCB specimens, it was further found that displacement control tests resulted in higher debond growth rates than did load control tests. While the symmetric DCB tests always resulted in cohesive failures in the bondline, the unsymmetric DCB tests resulted in the debond growing into the thinner adherend and the damage progressing as delamination in that adherend. This behavior resulted in much lower fracture toughness and damage growth rates than found in the symmetric DCB tests.

Mangalgiri, P. D.↗
NASA NTRS2016

Using Tabulated Experimental Data to Drive an Orthotropic Elasto-Plastic Three-Dimensional Model for Impact Analysis

An orthotropic elasto-plastic-damage three-dimensional model with tabulated input has been developed to analyze the impact response of composite materials. The theory has been implemented as MAT 213 into a tailored version of LS-DYNA being developed under a joint effort of the FAA and NASA and has the following features: (a) the theory addresses any composite architecture that can be experimentally characterized as an orthotropic material and includes rate and temperature sensitivities, (b) the formulation is applicable for solid as well as shell element implementations and utilizes input data in a tabulated form directly from processed experimental data, (c) deformation and damage mechanics are both accounted for within the material model, (d) failure criteria are established that are functions of strain and damage parameters, and mesh size dependence is included, and (e) the theory can be efficiently implemented into a commercial code for both sequential and parallel executions. The salient features of the theory as implemented in LS-DYNA are illustrated using a widely used composite - the T800S/3900-2B[P2352W-19] BMS8-276 Rev-H-Unitape fiber/resin unidirectional composite. First, the experimental tests to characterize the deformation, damage and failure parameters in the material behavior are discussed. Second, the MAT213 input model and implementation details are presented with particular attention given to procedures that have been incorporated to ensure that the yield surfaces in the rate and temperature dependent plasticity model are convex. Finally, the paper concludes with a validation test designed to test the stability, accuracy and efficiency of the implemented model.

Polymer Matrix Composites↗
NASA NTRS1991

Analysis of thermomechanical fatigue of unidirectional titanium metal matrix composites

Thermomechanical fatigue (TMF) data was generated for a Ti-15V-3Cr-3Al-3Sn (Ti-15-3) material reinforced with SCS-6 silicon carbide fibers for both in-phase and out-of-phase thermomechanical cycling. Significant differences in failure mechanisms and fatigue life were noted for in-phase and out-of-phase testing. The purpose of the research is to apply a micromechanical model to the analysis of the data. The analysis predicts the stresses in the fiber and the matrix during the thermal and mechanical cycling by calculating both the thermal and mechanical stresses and their rate-dependent behavior. The rate-dependent behavior of the matrix was characterized and was used to calculate the constituent stresses in the composite. The predicted 0 degree fiber stress range was used to explain the composite failure. It was found that for a given condition, temperature, loading frequency, and time at temperature, the 0 degree fiber stress range may control the fatigue life of the unidirectional composite.

Mirdamadi, M.↗
DOE OSTI2023

Using Homogenized Models to Explore the Effect of Fracture Densities on Weathering

Despite its importance, only a few researchers have incorporated the effects of fracturing into models of reactive transport for rock weathering. Here we explore 2D simulations that describe weathering under conditions of diffusive and advective transport within heterogeneous media consisting of rocky blocks and fractures. In our simulations, the Darcy velocities vary in space and time and depend on weathering processes within the rock matrix. We explore simulations with saturated and unsaturated flow for weathering bedrock that consists of blocks separated by inert or weathered material. The simulations show that a simplified homogenized model can approximate exact solutions for some of the simulated columns and hills and can allow exploration of coupling between flow and reaction in fractured rock. These hillslope simulations document that, even in the presence of 2D water flow, i) an increase in fracture density results in faster weathering advance rates; and ii) the water table locates deeper for a rock system that is weathered and fractured rather than weathered and unfractured. Some of these patterns have also been observed for natural systems. But these simulations also highlight how simplified models that do not use appropriate averaging of heterogeneities can be inaccurate in predicting weathering rate for natural systems. For example, if water flows both vertically and laterally through the vadose zone of a hill, then a prediction of the depth of regolith that is based on modeling strictly unidirectional downward infiltration will be unrealistically large. Likewise, if the fracture density observed near the land surface is used in a model to predict depth of weathering for a system where the fracture density decreases downward, the model will overestimate regolith depth. Learning how to develop accurately homogenized models could thus enable better conceptual models and predictions of weathering advance in natural systems.

58 GEOSCIENCES↗
NASA NTRS1975

An investigation of the failure and fracture behavior of graphite/epoxy laminates

A fundamental investigation of the fracture behavior of fiber reinforced composites is discussed. It is suggested that experimental and analytical investigations should compliment each other. Further, it is suggested that in order to understand and mathematically model composite fracture it is necessary to explore, understand and characterize the stress-strain behavior of each type of laminate tested from initial loading to incipient fracture. That is, it is not only necessary to perform fracture studies but it is necessary to perform stress-strain characterization and failure studies as well. For this reason a literature survey is presented in which these three elements are discussed. An experimental program to determine tensile properties of unnotched and notched unidirectional and multi-directional laminates composed of Hercules AS Fiber and 3501 Resin is described. Experimental unnotched moduli and strengths are presented, discussed and compared to lamination theory predictions. It is shown that rate effects are small and that lamination theory gives good results for moduli but not for strengths.

Brinson, H. F.↗
NASA NTRS2001

Inexpensive Method for Growing Unidirectional Oriented Materials Using Friction-Transferred Poly(tetrafluoroethylene) Substrates

In recent years, there has been an increasing interest in properties of unidirectional materials grown on highly oriented polymer surfaces such as the poly(tetrafluoroethylene) (PTFE) films coated onto smooth glass surfaces. In this technique, a thin PTFE film is deposited by sliding or rubbing a Teflon bar over a heated glass surface at a specific temperature. Depending on the pressure, temperature and sliding rate the thickness of deposited layers can be varied from 30 A to 150 A. The PTFE-coated substrate is simple yet surprising versatile for oriented growth of many organic, inorganic and polymer. The significant aspect of PTFE films is their unusual ability to molecularly align a wide variety of materials grown onto them from solution, melt or vapor phase deposition, at temperature below the melting point of PTFE (approx. 340 C). The PTFE structure may be derived, in part, from the multitude of ridges forming in the film and these ridges can presumably provide effective nucleation sites to induce the unidirectional growth of variety of materials. Electron diffraction studies of these films revealed that the PTFE macromolecules are oriented parallel to each other along the sliding direction. Direct observation of the film thickness, molecular structure and individual fluorine atoms from these highly oriented films were achieved using atomic force microscopy (AFM). In this paper, we also report the first direct observation of individual fluorine atoms, and the measurement of the fluorine-helix and carbon-helix radii to be 1.70 A and 0.54 A, respectively.

Lee, Jonathan A.↗
NASA NTRS1990

Mixed-Mode Bending Method for Delamination Testing

A mixed mode delamination test procedure was developed combining double cantilever beam (DCB) mode I loading and end-notch fixture (ENF) mode II loading on a split unidirectional laminate. By loading with a lever, a single applied load simultaneously produces mode I and mode II bending loads on the specimen. This mixed-mode bending (MMB) test was analyzed using both finite-element procedures and beam theory to calculate the mode I and mode II components of strain-energy release rate G(sub I) and G(sub II), respectively. A wide range of G(sub I)/G(sub II) ratios can be produced by varying the load position on the lever. As the delamination extended, the G(sub I)/G(sub II) ratios varied by less than 5%. Beam theory equations agreed closely with the finite-element results and provide a basis for selection of G(sub I)/G(sub II) test ratios and a basis for computing the mode I and mode II components of measured delamination toughness. The MMB test was demonstrated using AS4/PEEK (APC2) unidirectional laminates. The MMB test introduced in this paper is rather simple and is believed to offer several advantages over most current mixed-mode test.

Reeder, James R.↗
NASA NTRS1994

Micromechanical modeling of damage growth in titanium based metal-matrix composites

The thermomechanical behavior of continuous-fiber reinforced titanium based metal-matrix composites (MMC) is studied using the finite element method. A thermoviscoplastic unified state variable constitutive theory is employed to capture inelastic and strain-rate sensitive behavior in the Timetal-21s matrix. The SCS-6 fibers are modeled as thermoplastic. The effects of residual stresses generated during the consolidation process on the tensile response of the composites are investigated. Unidirectional and cross-ply geometries are considered. Differences between the tensile responses in composites with perfectly bonded and completely debonded fiber/matrix interfaces are discussed. Model simulations for the completely debonded-interface condition are shown to correlate well with experimental results.

Sherwood, James A.↗
NASA NTRS1988

A mixed-mode bending apparatus for delamination testing

A mixed-mode delamination test procedure was developed combining double cantilever beam mode I loading and end notch flexure mode II loading on a split unidirectional laminate. By loading the specimen with a lever, a single applied load simultaneously produces mode I and II bending loads on the specimen. This mixed mode bending (MMB) test was analyzed using both finite element procedures and beam theory to calculate the mode I and II components of strain energy release rate, G sub I and G sub II, respectively. The analyses showed that a wide range of G sub I/G sub II ratios could be produced by varying the applied load position on the loading lever. As the delamination extended, the G sub I/G sub II ratios varied by less than 5 percent. The simple beam theory equations were modified to account for the elastic interaction between the two arms of the specimen and to account for shear deformations. The resulting equations agreed closely with the finite element results and provide a basis for selection of G sub I/G sub II test ratios and a basis for computing the mode I and II components of measured delamination toughness. The MMB specimen analysis and test procedures were demonstrated using unidirectional laminates.

Crews, John H., Jr.↗
DOE OSTI2025

Interplay of Nanoscale Strain and Smectic Susceptibility in Kagome Superconductors

Exotic quantum solids can host electronic states that spontaneously break rotational symmetry of the electronic structure, such as electronic nematic phases and unidirectional charge density waves (CDWs). When electrons couple to the lattice, uniaxial strain can be used to anchor and control this electronic directionality. Here, we reveal an unusual impact of strain on unidirectional “smectic” CDW orders in kagome superconductors AV 3⁢ Sb 5 using spectroscopic-imaging scanning tunneling microscopy. We discover local decoupling between the smectic electronic director axis and the direction of anisotropic strain. While the two can generally be aligned along the same direction in regions of a small CDW gap, the tendency for alignment decreases in regions where the CDW gap is the largest. This feature, in turn, suggests nanoscale variations in smectic susceptibility, which we attribute to a combination of local strain and electron correlation strength. Overall, we observe an unusually high decoupling rate between the smectic electronic director of the three-state Potts order and anisotropic strain, revealing weak smectoelastic coupling in the CDW phase of kagome superconductors. This finding is phenomenologically different from the extensively studied nematoelastic coupling in the Ising nematic phase of Ising nematic phase of Fe-based superconductor bulk single crystals, providing a contrasting picture of how strain can control electronic unidirectionality in different families of quantum materials.

Wang, Yidi [Boston College, Chestnut Hill, MA (Uni↗
NASA NTRS2021

Numerical Validation of Composite Panel Impact Tests

Researchers have met the challenge of modeling impact events involving composite targets for a variety of applications in a variety of ways. In this paper, the theory and implementation details of an orthotropic visco-elastic-visco-plastic material model with strain rate dependence are discussed. The model is driven by experimental data from quasi-static as well as high strain rate tests, and the data is used in defining the deformation, damage and failure sub-models. Validation data is generated by shooting a hollow 50 g Al-2024 projectile at different velocities against a flat panel target made of unidirectional composite material in a 16-ply [(0/90/45/-45)_(2)]_(S) layup. Explicit dynamic finite element analyses of four high speed tests involving one contained (projectile rebounded) and three uncontained (projectile penetrated) impact tests show that the developed material model and modeling techniques yield reasonable and acceptable predictions.

Orthotropic Composite↗
NASA NTRS1985

Advances and trends in structures and dynamics; Proceedings of the Symposium, Washington, DC, October 22-25, 1984

Among the topics discussed are developments in structural engineering hardware and software, computation for fracture mechanics, trends in numerical analysis and parallel algorithms, mechanics of materials, advances in finite element methods, composite materials and structures, determinations of random motion and dynamic response, optimization theory, automotive tire modeling methods and contact problems, the damping and control of aircraft structures, and advanced structural applications. Specific topics covered include structural design expert systems, the evaluation of finite element system architectures, systolic arrays for finite element analyses, nonlinear finite element computations, hierarchical boundary elements, adaptive substructuring techniques in elastoplastic finite element analyses, automatic tracking of crack propagation, a theory of rate-dependent plasticity, the torsional stability of nonlinear eccentric structures, a computation method for fluid-structure interaction, the seismic analysis of three-dimensional soil-structure interaction, a stress analysis for a composite sandwich panel, toughness criterion identification for unidirectional composite laminates, the modeling of submerged cable dynamics, and damping synthesis for flexible spacecraft structures.

Noor, A. K.↗