Single stage experimental evaluation of compressor blading with slots and vortex generators. Part 1 - Analysis and design of stages 4 and 5
Analysis and design of compressor blading with slots and vortex generators
Brent, J. A.↗
SEARCH · Search NASA
Results for “vortex generators”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Vortex generators as a means for increasing rotor performance
Field tests on a horizontal axis wind turbine (HAWT) have shown that Vortex Generators (VGs) can increase the efficiency of large propeller type (horizontal axis) wind turbines. VGs are devices which are attached to the surfaces of an aerodynamic body to influence the boundary layer behavior. It is pointed out that VGs were originally developed for delaying stall on aircraft wings. An investigation was conducted regarding the possibility to employ VGs also for the improvement of the performance of an intermediate size HAWT with a diameter in the range from 24 to 46 meters. This investigation included wind tunnel tests involving a rotor blade tip section, and field tests. The wind tunnel tests showed that VGs can improve the peak lift capabilities of the section while only slightly increasing the drag. The field tests showed that VGs can increase the rotor power in winds above 6 m/s.
Corrigan, R. D.↗
Transition Delay via Vortex Generators in a Hypersonic Boundary Layer at Flight Conditions
The potential of realizable, stationary streaks undergoing non-modal growth to stabilize a hypersonic boundary-layer flow and, subsequently, delay the laminar-turbulent transition onset, is studied via numerical computations. The geometry and flow conditions are selected to match a relevant trajectory location from the ascent phase of the HIFiRE-1 flight experiment, namely, a 7-degree half-angle cone with 2.5 mm nose radius, freestream Mach number of 5.30, freestream unit Reynolds number equal to 13.42 x 10(exp 6)/m, and wall-to-adiabatic temperature ratio of approximately 0.35 over most of the test article. This paper investigates flow modifications induced by wall-mounted vortex generators (VGs), followed by an analysis of the modal instability of the perturbed, streaky boundary-layer flow. Results are presented both for a single array of VGs that was designed on the basis of optimal growth theory and for a VG configuration involving two separate arrays with opposite orientations that ware designed to provide staged control of flow instabilities while simultaneously reducing the amplification of streak instabilities resulting from the control devices. Earlier research had shown that the onset of transition during the HIFiRE-1 flight experiment, which did not include any control devices, correlated with an amplification factor of N = 14.7 for the planar Mack modes. If one assumes that the transition N -factor is not affected by the introduction of the VGs, then the control configurations based on a single array of VGs and two separate arrays would result in a transition delay of 17% and 40%, respectively. These findings suggest a passive flow control s to induce streaks that would delay transition in hypersonic boundary dominated by Mack-mode instabilities.
Incompressible boundary layer↗
Single-stage experimental evaluation of compressor blading with slots and vortex generators. Part 3 - Data and performance for stage 4
Data and performance of stage four of compressor blades with slots and vortex generators
Brent, J. A.↗
Single-stage experimental evaluation of compressor blading with slots and vortex generators. Part 4 - Supplemental data for stage 4
Supplementary data tables for single stage experimental evaluation of compressor blading with slots and vortex generators
Brent, J. A.↗
On the aerodynamics and performance of active vortex generators
As a building block in the development of smart lift-enhancement devices, a new concept for flow control using active vortex generators (AVGs) is presented. Ramp, wedge, and doublet wedge (Wheeler) VG configurations are investigated. The AVGs are designed to conform to the surface of the wing section at low alpha. As the section approaches the stall, they are deployed and accordingly, alpha(stall) and C(lmax) are increased. A qualitative analysis of the flow around the various VG configurations was conducted in a low speed wind tunnel at 1.6 ft/s and a Reynolds number of approximately 3400. The results demonstrate that ramp VGs produce vortices that have the longest distance at breakdown. The VGs were also applied to a 25-in. span, 8-in. chord NACA 4415 wing section. Optimization studies were conducted on the spanwise spacing, chordwise position, and size of statically deployed VGs. The test results demonstrate a 14-percent increase in C(lmax) while increasing alpha (stall) by up to 3.
Barrett, Ron↗
Simulations Of On Demand Vortex Generators
The development of a two-dimensional viscous incompressible flow generated by an off center thin oscillating bd on top of a cavity is studied computationally as a prototype of vortex generators. The lid is placed asymmetrically over the cavity so that the gap size is different on either side of the cavity. An adaptive numerical scheme, based on high resolution viscous vortex methods, is used to integrate the vorticity/velocity formulation of the Navier-Stokes equations with the no-slip boun.lary condition enforced on the lid and cavity walls. Depending on the a amplitude and frequency of the oscillation as well as the the gap size, vorticity is ejected in the fluid above the cavity either from the large and/or the small gap. The results of the computations complement ongoing experimental work.
Koumoutsakos, P.↗
Direct numerical simulations of on-demand vortex generators: Mathematical formulation
The objective of the present research is the development and application of efficient adaptive numerical algorithms for the study, via direct numerical simulations, of active vortex generators. We are using innovative computational schemes to investigate flows past complex configurations undergoing arbitrary motions. Some of the questions we try to answer are: Can and how may we control the dynamics of the wake? What is the importance of body shape and motion in the active control of the flow? What is the effect of three-dimensionality in laboratory experiments? We are interested not only in coupling our results to ongoing, related experimental work, but furthermore to develop an extensive database relating the above mechanisms to the vortical wake structures with the long-range objective of developing feedback control mechanisms. This technology is very important to aircraft, ship, automotive, and other industries that require predictive capability for fluid mechanical problems. The results would have an impact in high angle of attack aerodynamics and help design ways to improve the efficiency of ships and submarines (maneuverability, vortex induced vibration, and noise).
Koumoutsakos, Petros↗
Stability Analysis of Streaks Induced By Optimized Vortex Generators
Numerical computations are performed to investigate the potential for transition control in an axisymmetric boundary layer via fully realizable, streamwise stationary streaks induced by an azimuthally periodic array of surface mounted vortex generators (VGs). Previous work has shown that suitable streaks of this type can significantly reduce the growth of Mack’s second mode instabilities, but large streak amplitudes can make the flow susceptible to previously absent streak instabilities that can become the leading cause of transition. Here, we use the adjoint capabilities of the SU2 flow solver to optimize the VG shape to maximize the reduction in the growth of second-mode disturbances while also preventing the streak amplitudes from reaching large enough values to precipitate an earlier onset of transition via streak instabilities. The geometry and the freestream flow conditions are selected to match a relevant trajectory lo-cation from the HIFiRE-1 flight experiment. Results show that the optimized VGs can increase the mean streak amplitude by 117% with respect to a manually developed baseline design. The stability of this optimized basic state is analyzed via the plane-marching parabolized stability equations, predicting a fully laminar flow over the entire cone, or equivalently, yielding transition delay of 130% versus the 17% for the baseline VGs.
Boundary layer transition↗
Surface pressure measurements on the blade of an operating Mod-2 wind turbine with and without vortex generators
Pressure measurements covering a range of wind velocities were made at one span location on the surface of an operating Mod-2, 2500 kW, wind turbine blade. The data, which were taken with and without vortex generators installed on the leading edge, show the existence of higher pressure coefficients than would be expected from two-dimensional wind tunnel data. These high pressure ratios may be the result of three-dimensional flow over the blade, which delays flow separation. Data are presented showing the repetitiveness of abrupt changes in the pressure distribution that occur as the blade rotates. Calculated values of suction and flap coefficients are also presented.
Nyland, Ted W.↗
Vortex-generating coolant-flow-passage design for increased film-cooling effectiveness and surface coverage
The thermal film-cooling footprints observed by infrared imagery for three coolant-passage configurations embedded in adiabatic-test plates are discussed. The configurations included a standard round-hole cross section and two orientations of a vortex-generating flow passage. Both orientations showed up to factors of four increases in both film-cooling effectiveness and surface coverage over that obtained with the round coolant passage. The crossflow data covered a range of tunnel velocities from 15.5 to 45 m/sec with blowing rates from 0.20 to 2.05. A photographic streakline flow visualization technique supported the concept of the counterrotating apability of the flow passage design and gave visual credence to its role in inhibiting flow separation.
Papell, S. S.↗
Flow Control on Low-Pressure Turbine Airfoils Using Vortex Generator Jets
Motivation - Higher loading on Low-Pressure Turbine (LPT) airfoils: Reduce airfoil count, weight, cost. Increase efficiency, and Limited by suction side separation. Growing understanding of transition, separation, wake effects: Improved models. Take advantage of wakes. Higher lift airfoils in use. Further loading increases may require flow control: Passive: trips, dimples, etc. Active: plasma actuators, vortex generator jets (VGJs). Can increased loading offset higher losses on high lift airfoils. Objectives: Advance knowledge of boundary layer separation and transition under LPT conditions. Demonstrate, improve understanding of separation control with pulsed VGJs. Produce detailed experimental data base. Test and develop computational models.
Volino, Ralph J.↗
Theoretical performance of a vortex generator type of cloud droplet sampler
One of the goals of the NASA global tropospheric research program is understanding the chemical processes which influence the chemistry of the natural troposphere. An important element of this program is the study of the role of heterogenous chemistry in global tropospheric chemical cycles. Any study of the part which clouds play in the chemistry of tropospheric trace constituents requires a determination of cloud water chemical composition. There exists, therefore, a need for highly efficient collector devices which can obtain unbiased samples of cloud water in sufficient quantities aboard an aircraft platform. A promising concept which could meet the dual requirements of accurate sampling and efficient collection of cloud water droplets in the vortex generator. This concept involves an inertial separator which uses the centrifugal force of a rotating airstream. The separator is built into a commercial device which has been used for many years as a dust separator for air breathing engines. Attention is given to the optimization of the sampler design.
Miller, I. M.↗
Subsonic longitudinal and lateral-directional static aerodynamic characteristics of a general research fighter configuration employing a jet sheet vortex generator
A configuration concept for developing vortex lift, which replaces the physical wing strake with a jet sheet generated fluid strake, was investigated on a general research fighter model. The vertical and horizontal location of the jet sheet with respect to the wing leading edge was studied over a momentum coefficient range from 0 to 0.24 in the Langley 7- by 10-foot high speed tunnel over a Mach number range from 0.3 to 0.8. The angle of attack range studied was from -2 to 30 deg at sideslip angles of 0, -5, and 5 deg. Test data are presented without analysis.
Huffman, J. K.↗
Characteristics of wake vortex generated by a Boeing 727 jet transport during two-segment and normal ILS approach flight paths
A series of flight tests was conducted to evaluate the vortex wake characteristics of a Boeing 727 (B727-200) aircraft during conventional and two-segment ILS approaches. Twelve flights of the B727, which was equipped with smoke generators for vortex marking, were flown and its vortex wake was intentionally encountered by a Lear Jet model 23 (LR-23) and a Piper Twin Comanche (PA-30). Location of the B727 vortex during landing approach was measured using a system of photo-theodolites. The tests showed that at a given separation distance there were no readily apparent differences in the upsets resulting from deliberate vortex encounters during the two types of approaches. Timed mappings of the position of the landing configuration vortices showed that they tended to descend approximately 91 m(300 ft) below the flight path of the B727. The flaps of the B727 have a dominant effect on the character of the trailed wake vortex. The clean wing produces a strong, concentrated vortex but as the flaps are lowered, the vortex system becomes more diffuse. Pilot opinion and roll acceleration data indicate that 4.5 n.mi. would be a minimum separation distance at which roll control of light aircraft (less than 5,670 kg (12,500 lb) could be maintained during parallel encounters of the B727's landing configuration wake. This minimum separation distance is generally in scale with results determined from previous tests of other aircraft using the small roll control criteria.
Kurkowski, R. L.↗
Modeling of vortex generated sound in solid propellant rocket motors
There is considerable evidence based on both full scale firings and cold flow simulations that hydrodynamically unstable shear flows in solid propellant rocket motors can lead to acoustic pressure fluctuations of significant amplitude. Although a comprehensive theoretical understanding of this problem does not yet exist, procedures were explored for generating useful analytical models describing the vortex shedding phenomenon and the mechanisms of coupling to the acoustic field in a rocket combustion chamber. Since combustion stability prediction procedures cannot be successful without incorporation of all acoustic gains and losses, it is clear that a vortex driving model comparable in quality to the analytical models currently employed to represent linear combustion instability must be formulated.
Flandro, G. A.↗
Use of Vortex Generators to Reduce Distortion for Mach 1.6 Streamline-Traced Supersonic Inlets
Reduce the total pressure distortion at the engine-fan face due to low-momentum flow caused by the interaction of an external terminal shock at the turbulent boundary layer along a streamline-traced external-compression (STEX) inlet for Mach 1.6.
supersonic inlets↗
Historical Overview of Research on Lift-Generated Vortex Wakes
A historical overview is presented of research conducted on the structure and modification of the vortices generated by the lifting surfaces of subsonic transport aircraft. Although primarily presented from an experimental point of view, the use of relatively compact theoretical formulations and concepts are used to indicate the progress made. It is pointed out that the first objective of the research is to reduce the magnitude of the hazard potential posed by the wakes of aircraft by modifying the aerodynamics of the wake-generating aircraft. A secondary objective is to develop the technology that will make it possible to safely avoid vortex wakes in the airport environment for increased capacity. If either or both objectives are achieved, the hazard posed by vortex wakes should have a greatly reduced impact on the operational capacity of airports for landings and takeoffs. Since a satisfactory solution to either of these two goals have not yet been achieved, the last part of the presentation will be devoted to a discussion of some requirements that have been placed on any prospective solution to either goal, if is to be acceptable. The material to be used in the presentation is published in the open literature.
Rossow, Vernon J.↗