Search NASA⌕ Search

SEARCH · Search NASA

Results for “wide”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Triple-halide wide–band gap perovskites with suppressed phase segregation for efficient tandems

Wide–band gap metal halide perovskites are promising semiconductors to pair with silicon in tandem solar cells to pursue the goal of achieving power conversion efficiency (PCE) greater than 30% at low cost. However, wide–band gap perovskite solar cells have been fundamentally limited by photoinduced phase segregation and low open-circuit voltage. Here, we report efficient 1.67–electron volt wide–band gap perovskite top cells using triple-halide alloys (chlorine, bromine, iodine) to tailor the band gap and stabilize the semiconductor under illumination. We show a factor of 2 increase in photocarrier lifetime and charge-carrier mobility that resulted from enhancing the solubility of chlorine by replacing some of the iodine with bromine to shrink the lattice parameter. We observed a suppression of light-induced phase segregation in films even at 100-sun illumination intensity and less than 4% degradation in semitransparent top cells after 1000 hours of maximum power point (MPP) operation at 60°C. By integrating these top cells with silicon bottom cells, we achieved a PCE of 27% in two-terminal monolithic tandems with an area of 1 square centimeter.

14 SOLAR ENERGY↗
DOE OSTI2020

Formation of wide-blocky calcite veins by extreme growth competition

Liassic limestones on the coast of Somerset in the UK contain dense arrays of calcite microveins with a common, but poorly understood microstructure, characterized by laterally wide crystals that form bridges across the vein. We investigated the mechanisms of formation and evolution of these ‘wide-blocky’ vein microstructures using a combination of high-resolution analytical methods, including virtual petrography, optical cathodoluminescence and scanning electron microscopy techniques (e.g. energy-dispersive X-ray spectrometry, back-scattered electron imaging, cathodoluminescence and electron back-scattered diffraction), laboratory experiments and multiphase field modelling. Our results indicate that the studied veins formed in open, fluid-filled fractures, each in a single opening and sealing episode. As shown by the optical and electron back-scattered diffraction images, the vein crystals grew epitaxially on grains of the wall rock and we hypothesize that their growth rates differed depending on whether the crystals were on a wall rock grain substrate that fractured intergranularly (slow growth rates) or transgranularly (rapid growth rates). Our multiphase field models support this hypothesis, showing that wide, blocky crystals only form where there are significant differences in the growth rate and are dependent on the type of seed grain. These results provide strong evidence for extreme growth competition, a process that we propose controls vein-filling in many micritic carbonate reservoirs, as well as demonstrate that the characteristics of the fracture wall can affect the filling processes in syntaxial veins. Supplementary material: The description and images of the studied thin sections are available at https://doi.org/10.6084/m9.figshare.c.5172371 . High-resolution optical microscopy mosaics (under plane-polarized- and crossed polarized light) of the thin section collection in PetroScan file format are available on request from the authors.

Geology↗
DOE OSTI2022

Temporal and spatial laser intensification within nodular defects overcoated with multilayer dielectric mirrors over a wide range of defect geometries

The nodular defect shape and the laser incidence angle have a dramatic impact on the spatial distribution of light intensification within the nodule as well as how the laser light is drained from the defect. Nodular defect geometries unique to ion beam sputtering, ion-assisted deposition, and electron-beam (e-beam) deposition, respectively, are modeled in this parametric study over a wide range of nodular inclusion diameters and layer count for optical interference mirror coatings constructed with quarter-wave thicknesses and capped with a half wave of the low index material. It was found for hafnia ($n$=1.9) and silica ($n$=1.45) multilayer mirrors that the light intensification in nodular defects with a $C$ factor of 8, typical of e-beam deposited coatings deposited with a wide range of deposition angles, was maximized for a 24-layer design. For intermediate size inclusion diameters, increasing the layer count for normal incidence multilayer mirrors reduced the light intensification within the nodular defect. A second parametric study explored the impact of the nodule shape on the light intensification for a fixed number of layers. In this case, there is a strong temporal trend for the different nodule shapes. Narrow nodules tend to drain more laser energy through the bottom of the nodule into the substrate while wide nodules tend to drain more laser energy through the top of the nodule when irradiated at normal incidence. Further, at a 45° incidence angle, waveguiding is an additional method to drain laser energy from the nodular defect. Finally, laser light resonates within nodular defects longer than within the adjacent nondefective multilayer structure.

47 OTHER INSTRUMENTATION↗
DOE OSTI2024

Genome-wide Association Study Identifies Candidate Loci with Major Contributions to the Genetic Control of Pod Morphological Traits in Snap Bean

Snap beans are cultivars of common bean (Phaseolus vulgaris) that are cultivated for their fleshy immature pods that exhibit a wide diversity of pod shapes and sizes. The genetic basis of the snap bean pod shape is complex and involves the interaction of multiple genes. This study used a snap bean diversity panel composed of heirloom and improved cultivars used in North America and genome-wide association studies (GWAS) to investigate the genetic basis of pod morphological characteristics, including length, width, height, width/height ratio, and coefficients of variation (CVs). The GWAS detected multiple genomic regions associated with each pod trait, with a total of 20 quantitative trait loci (QTLs) for pod length, 9 for pod width, 14 for pod height, and 10 for pod width/height ratio. Regarding theCVof each pod trait, genome-wide association analyses detected six QTL for lengthCVs, five for widthCVs, 15 for heightCVs, and six for width/height ratioCVs. Thirteen regions in seven chromosomes were associated with two or more pod traits. Eighteen QTLs for pod traits in this study colocated with previously reported QTLs for pod and seed traits. The QTL intervals encompass gene models with homologues in other species that are involved in the control of developmental processes. These results capture the complex nature of the genetic control of snap bean pod traits and confirm the significance of genomic regions harboring overlapping QTLs identified in this and other studies. The phenotypic expression of pod traits in snap bean appears to be under the control of a few genomic regions with a strong effect with additional contributions of multiple small-effect regions. Validation of the function of the candidate genes identified in associated regions will contribute to our understanding of legume pod development.

Agriculture↗
DOE OSTI2021

Highly Integrated Wide Bandgap Power Module for Next Generation Plug-In Vehicles (Final Report)

Wide bandgap devices are key enablers for high power density traction inverters. A highly integrated wide bandgap (WBG) power module enables higher temperature operation, higher inverter efficiency and overall smaller die area with the same power delivery. However, it requires careful design of the power module to take advantage of all the superior material properties that silicon carbide (SiC) provides over conventional silicon (Si) Insulated Gate Bipolar Transistor (IGBT) based design. This project developed an efficient and densely packed SiC power module for an automotive traction inverter application. Extensive study was performed to select the best performing SiC die considering a wide range of temperature variation, suitability to integrate into target packaging, robust body diode performance and overall high electrical efficiency. Multiple design ideas were explored to achieve lower stray inductance for both power loop and signal loop, uniform current distribution, compact form factor, and very high thermal performance. The final power module package includes all six inverter switches in the same module (six-pack) with die sintered at both bottom and top surfaces utilizing high performance substrate to achieve high electrical and thermal performance. Two power module variants were developed using 900 V and 1200 V devices for operating at two different high voltage levels (> 600 V HV battery). Both power modules were comprehensively characterized, and high efficiency operation of the inverter was confirmed through analysis. Finally, a complete functional inverter was built with the 1200V power modules using other essential components (HV capacitors, gate driver board, controller board, current sensor, connectors etc.) and tested using GM’s standard test procedure. There are several challenges associated with adopting WBG devices for high voltage operation. In order to assess and mitigate those challenges, GM and subrecipients of this project have conducted multiple detailed studies. This includes phase current reconstruction using integrated Rogowski coil, device junction temperature estimation using on-state gate resistance, modeling and testing the effect of high voltage and fast switching on motor insulation and bearings, partial discharge inception voltage measurement under different environmental conditions. Findings of all these studies are summarized in this report.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2022

Kilonova Detectability with Wide-Field Instruments [Slides]

A diverse set of instruments increase the chances of detecting and identifying a kilonova. Early observations increase the probability of detection. More sensitive wide-field ultraviolet instruments are needed as GW detectors reach design sensitivity. There is a dearth of wide-field infrared instruments. These results are useful for guiding kilonova searches following a GW detection and sGRD observation, proposals for time on current and upcoming instruments, and planning future wide-field instruments.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2022

Wide Bandgap Semiconductors for Extreme Temperature and Radiation Environments

With their greater voltage breakdowns, higher current limitations, and faster switching speeds, wide bandgap semiconductors are increasing in market application over the traditionally dominant silicon devices. Silicon carbide semiconductors have been increasing the efficiency and reducing the footprint of modern power electronics, and the increased electron mobility of gallium nitride semiconductors have been increasing the switching frequencies of radio frequency circuits. In extreme temperature (>225°C) applications and high radiation environments such as low earth orbit, deep space, and terrestrial nuclear reactors, silicon-based semiconductors degrade rapidly. Wide bandgap semiconductors are poised to disrupt the market for sensing, instrumentation, and communication circuitry in these hazardous environments by increasing the lifetime, safety, and reliability. This report outlines the advantages of using wide bandgap semiconductor materials in extreme temperature and radiation environments.

36 MATERIALS SCIENCE↗
DOE OSTI2022

WECC Wide-Area Oscillation Assessment and Trending Study Report

This project, Wide-area Oscillation Analysis and Trending Study, is sponsored by the Office of Electricity (OE) of the Department of Energy (DOE) who tasked Northwest National Laboratory (PNNL) to conduct this research. Staff of Federal Energy Regulatory Commission (FERC) have been involved in the project as observers and have provided advisory comments and suggestions. The primary objective of this study is to assess whether there are significant trends in the wide-area oscillatory behavior with respect to the significant generation-mix changes brought by the increased penetration of RES in the WECC system. The work performed in this project is considered to be complimentary to previous work by NERC/industry and covers the aspects that have not been studied or trended before. The trending analysis presented in this report can serve as reference for future grid planning and operation of the WECC system. In this report, how the changes in the generation mix can impact the frequency and damping ratio (DR) of WECC wide-area oscillation modes has been studied. Thorough data-based and model-based analyses have been carried out to analyze the current trends and then extended to evaluate the oscillation behaviors of the future WECC system.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2024

Joint Comments from the Department of Energy, National Nuclear Security Administration (DOE NNSA) Los Alamos Field Office and Triad National Security, LLC on the U.S. Environmental Protection Agency’s New Mexico State-Wide Municipal Separate Storm Sewer System Strawman General Permit

In December 2020 and March 2021, EPA issued two MS4 strawman permit drafts specific to the Los Alamos area. EPA made text changes in the 2 nd strawman permit based on stakeholder comments related to the initial draft. During the public meeting on the Los Alamos area designation decision held on February 13, 2024, EPA staff stated that comments from the past strawman permits would be incorporated into the new MS4 permit to be issued state-wide. However, it does not appear that any of the text changes from the 2 nd Los Alamos area strawman permit were included in this state-wide general MS4 strawman permit. For reference, the 2 nd Los Alamos area revised strawman permit is included with these comments as Attachment 2. Many of the following comments refer to or state EPA’s updated text included in the 2 nd Los Alamos area strawman permit. The updated text from this 2 nd strawman permit that are referenced in the following comments should be applicable state-wide and it is suggested that this past work be reconsidered and incorporated.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1975

Unique wide field of view visual simulation

Visual simulations are required to support investigations of the man-machine aspects of helicopter nap-of-the-earth flight. The visual simulation requirements are discussed vis-a-vis available technology. A wide field of view of the world outside the cockpit is necessary to provide adequate visual cues to the pilot. A unique design is described employing three TV monitors, collimating lenses, and electronics to selectively display a wide field of view without the use of a costly wide angle optical probe.

Niemela, J.↗
NASA NTRS1978

Optimization of the design parameters for a wide-band radiometric system

The optimun design parameters for a swept frequency wide-band radiometric antenna system for spacecraft applications are studied. Wide band antenna systems are needed to observe layered surfaces which are frequency sensitive and require multiple measurements for interpretation. The lowest frequency band of interest is between 1.4 to 2.8 Ghz. Starting with a given size reflector fed in the offset mode by a corrugated horn located at the focus of the parabola, the primary performance indexes; e.g., half power beamwidth, cross polarization level, and overall beam efficiency were calculated over a wide frequency range (two to one) for different physical horn dimensions and for different values of f/D ratio. These data are used to find the best design under given restriction of reflector size and blockage.

Agrawal, P. K.↗
NASA NTRS1977

System description and analysis. Part 1: Feasibility study for helicopter/VTOL wide-angle simulation image generation display system

A preliminary design for a helicopter/VSTOL wide angle simulator image generation display system is studied. The visual system is to become part of a simulator capability to support Army aviation systems research and development within the near term. As required for the Army to simulate a wide range of aircraft characteristics, versatility and ease of changing cockpit configurations were primary considerations of the study. Due to the Army's interest in low altitude flight and descents into and landing in constrained areas, particular emphasis is given to wide field of view, resolution, brightness, contrast, and color. The visual display study includes a preliminary design, demonstrated feasibility of advanced concepts, and a plan for subsequent detail design and development. Analysis and tradeoff considerations for various visual system elements are outlined and discussed.

Source record↗
NASA NTRS1982

Crucible Grows Wide Silicon Ribbon

Inexpensive manufacture of solar cells may require quality silicon ribbon crystals. One way to produce them is by growing wide dendritic webs, which can be very long and have high structural perfection. Dendrites grow from supercooled melt, so width of ribbon depends on how wide a region of supercooled molten silicon can be maintained in crucible. Elongated geometry of suscepter/crucible/lid assembly allows molten silicon to supercool over a wider region -- a necessary condition for the growth of wide dendritic crystal ribbon.

Seidensticker, R.↗
NASA NTRS1982

Wide Field and Planetary Camera for Space Telescope

The Space Telescope's Wide Field and Planetary Camera instrument, presently under construction, will be used to map the observable universe and to study the outer planets. It will be able to see 1000 times farther than any previously employed instrument. The Wide Field system will be located in a radial bay, receiving its signals via a pick-off mirror centered on the optical axis of the telescope assembly. The external thermal radiator employed by the instrument for cooling will be part of the exterior surface of the Space Telescope. In addition to having a larger (1200-12,000 A) wavelength range than any of the other Space Telescope instruments, its data rate, at 1 Mb/sec, exceeds that of the other instruments. Attention is given to the operating modes and projected performance levels of the Wide Field Camera and Planetary Camera.

Lockhart, R. F.↗
NASA NTRS1988

Wide binary stars at the Galactic poles

Results are reported from a search for high-Galactic-latitude wide binaries down to visual magnitude 14 on five digitized Schmidt-telescope plates. The data-reduction and analysis techniques are described in detail, and the results are presented in graphs and briefly characterized. The number of wide binaries and the estimated wide-binary number density are both three times smaller than those found by Bahcall and Soneira (1981), but still too large to be consistent with the predictions of physical models. Possible explanations for this discrepancy are explored.

Garnavich, Peter M.↗
NASA NTRS1991

A numerical procedure for recovering true scattering coefficients from measurements with wide-beam antennas

A numerical procedure for estimating the true scattering coefficient, sigma(sup 0), from measurements made using wide-beam antennas. The use of wide-beam antennas results in an inaccurate estimate of sigma(sup 0) if the narrow-beam approximation is used in the retrieval process for sigma(sup 0). To reduce this error, a correction procedure was proposed that estimates the error resulting from the narrow-beam approximation and uses the error to obtain a more accurate estimate of sigma(sup 0). An exponential model was assumed to take into account the variation of sigma(sup 0) with incidence angles, and the model parameters are estimated from measured data. Based on the model and knowledge of the antenna pattern, the procedure calculates the error due to the narrow-beam approximation. The procedure is shown to provide a significant improvement in estimation of sigma(sup 0) obtained with wide-beam antennas. The proposed procedure is also shown insensitive to the assumed sigma(sup 0) model.

Wang, Qinglin↗
NASA NTRS1991

A numerical procedure for recovering scattering coefficients from measurements with wide-beam antennas

A numerical procedure for estimating true scattering coefficients, sigma0, from measurements made using wide-beam antennas is discussed. The use of wide-beam antennas results in an inaccurate estimate of sigma0. To reduce this error, the authors propose a correction procedure that estimates the error resulting from the use of narrow-beam approximation and utilizes the error to obtain a more accurate estimate of sigma0. An exponential model is assumed to take into account the variation of sigma0 with incidence angles, and the model parameters are estimated from measured data. Based on the model and knowledge of the antenna pattern, the procedure calculates the error due to the narrow-beam approximation. The procedure is shown to provide a significant improvement in the estimation of sigma0 obtained in wide-beam antennas. The proposed procedure is also shown to be insensitive to the assumed sigma0 model.

Wang, Qinglin↗
NASA NTRS1993

Wide-angle imaging system with fiberoptic components providing angle-dependent virtual material stops

A strip imaging wide angle optical system is provided. The optical system is provided with a 'virtual' material stop to avoid aberrational effects inherent in wide angle optical systems. The optical system includes a spherical mirror section for receiving light from a 180 deg strip or arc of a target image. Light received by the spherical mirror section is reflected to a frustoconical mirror section for subsequent rereflection to a row of optical fibers. Each optical fiber transmits a portion of the received light to a detector. The optical system exploits the narrow cone of acceptance associated with optical fibers to substantially eliminate vignetting effects inherent in wide angle systems. Further, the optical system exploits the narrow cone of acceptance of the optical fibers to substantially limit spherical aberration. The optical system is ideally suited for any application wherein a 180 deg strip image need be detected, and is particularly well adapted for use in hostile environments such as in planetary exploration.

Vaughan, Arthur H.↗