Search NASA⌕ Search

SEARCH · Search NASA

Results for “yaw angle”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Yaw and spin effects on high intensity sound generation and on drag of training projectiles with ring cavities

Projectiles containing axisymmetric ring cavities constitute aeroacoustic sources. These produce high intensity tones which are used for coding in the SAWE (Simulation of Area Weapons Effects) system. Experimental data obtained in a free jet facility are presented describing the effects of yaw, spin and geometric projectile parameters on sound pressure and drag. In general, the sound pressure decreases with increasing yaw angle whereas the drag increases. Spin tends to increase sound pressure levels because of a reduction in asymmetry of flow. Drag increases at zero yaw approximately as the 1.5 power of sound wavelength. A significant part of the drag increase appears to be due to energy loss by sound radiation.

Parthasarathy, S. P.↗
NASA NTRS1978

An investigation of drag reduction for tractor trailer vehicles

Force and moment data were obtained from a one-twenty-fifth scale wind tunnel model of a cab-over-engine tractor trailer combination. The tests define the aerodynamic characteristics of the baseline (unmodified) vehicle and several modified configurations. The primary modifications consist of: (1) greatly increased forebody corner radii, (2) a smooth fairing over the cab-to-trailer gap, (3) a smoothed underbody, and (4) rear streamlining (boattailing)of the trailer. Tests were conducted for yaw angles from 0 deg to 30 deg. The reduction in drag, relative to the baseline, obtained by combining the modifications are compared for the zero yaw condition with full scale coast down drag results for similar configurations. The drag reductions obtained from the model and full scale tests are in good agreement.

Muirhead, V. U.↗
NASA NTRS1977

Investigation of a stall deterrent system utilizing an acoustic stall sensor

A simple rugged acoustic stall sensor which has an output proportional to angle of attack near wing stall has been evaluated on a Cessna 319 aircraft. A sensor position has been found on the wing where the sensor output is only slightly affected by engine power level, yaw angle, flap position and wing roughness. The NASA LRC General Aviation Simulator has been used to evaluate the acoustic sensor output as a control signal for active stall deterrent systems. It has been found that a simple control algorithm is sufficient for stall deterrence.

Bennett, A. G.↗
NASA NTRS1985

Numerical solution of the full-potential equation for rotors and oblique wings using a new wake model

A three-dimensional, full-potential, quasi-steady code TFAR1 is proposed for calculating the transonic flow past a lifting helicopter rotor blade and oblique wing. The TFAR1 uses a two-dimensional nonlinear wake-model that allows a jump in velocity potential to propagate with the local fluid flow in the wake. Rotor calculations were made for a single blade at an advance ratio of 0.3, a rotational tip Mach number of 0.7, and at 0-degree incidence. A 1/7-scale model of the Cobra Operational Load Survey (OLS) rotor blade is calculated, and the pressure distributions are compared to the measurements for azimuth angles 0, 30, 60, 90, 120, and 150 degrees at the 95 percent spanwise station of the OLS blade. Furthermore, an oblique wing with Korn airfoil was calculated at the high transonic free-stream Mach number of 0.9791, zero incidence, and yaw angle of 40 degrees. The TFAR1, coupled with a helicopter performance code CAMRAD (Johnson, 1981), provides a full-potential code for calculating the entire flow field for a multiple-bladed rotor in transonic lifting forward flight.

Chang, I.-C.↗
NASA NTRS1992

Non-propulsive aerodynamic noise

In the first part of the paper, the contribution of airframe noise to total aircraft noise on approach is assessed for a large current technology transport and for the same airframe powered with bypass ratio 10 engines with an additional 5 dB noise suppression applied to the fan and turbine noise sources. The airframe noise of the envisioned advanced subsonic transport is 2 EPNdB less than the largest contributor to the total aircraft noise, the fan inlet. The noise impact of the airframe noise, as measured by noise contour area, is 1/4 that of fan noise. Further fan noise reduction efforts should not view airframe noise as an absolute noise floor. In the second part of the paper, the results from one recent cavity noise wind tunnel experiment is reported. A cavity of dimensions 11.25 in. (28.58 cm) long, 2.5 in. (6.35 cm) wide, and variable depth was tested in the Mach number range of .20 through .90. Reynolds number varied from 5 to 100 million per foot (16 to 328 million per meter). The 1/d ratio was varied from 4.4 to 20.0. The model was tested at yaw angles from 0 to 15 degrees. In general, the deeper the cavity, the greater the amplitude of the acoustic tones. Reynolds number appeared to have little effect on acoustic tone amplitudes. Tone amplitude and bandwidth changed with Mach number. The effect of yaw on acoustic tones varied with Reynolds number, Mach number, 1/h, and mode number. At Mach number 0.90, increased yaw shifted the tone frequencies of the higher modal frequencies to lower frequencies. As cavity depth decreased, the effect of yaw decreased.

Willshire, William L., Jr.↗
NASA NTRS1987

Structure of supersonic turbulent flow past a sharp fin

The three-dimensional shock-wave/turbulent-boundary-layer interaction generated by a sharp fin is examined both experimentally and theoretically at Mach 3 for a fin angle 20 deg and Reynolds number 900,000. This study represents an extension of previous research for the sharp fin configuration to stronger interactions. The experimental data include surface pressure profiles, surface streamline patterns, and boundary-layer profiles of pitot pressure and yaw angle. Two separate theoretical approaches or 'models' were employed. Both models utilize the three-dimensional compressible Navier-Stokes equations in mass-averaged variables. The theoretical approach of Knight (1984 and 1985) employs the algebraic turbulent eddy-viscosity model of Baldwin and Lomax (1978), and the theoretical model of Horstman (1984) employs the two-equation turbulence model of Jones and Launder (1972) coupled with the wall function model of Viegas et al. (1985).

Knight, Doyle D.↗
NASA NTRS1973

Low-speed wind tunnel investigation of the lateral-directional characterisitcs of a large-scale variable wing-sweep fighter model in the high-lift configuration

The low-speed characteristics of a large-scale model of the F-14A aircraft were studied in tests conducted in the Ames Research Center 40- by 80-Foot Wind Tunnel. The primary purpose of the present tests was the determination of lateral-directional stability levels and control effectiveness of the aircraft in its high-lift configuration. Tests were conducted at wing angles of attack between minus 2 deg and 30 deg and with sideslip angles between minus 12 deg and 12 deg. Data were taken at a Reynolds number of 8.0 million based on a wing mean aerodynamic chord of 2.24 m (7.36 ft). The model configuration was changed as required to show the effects of direct lift control (spoilers) at yaw, yaw angle with speed brake deflected, and various amounts and combinations of roll control.

Eckert, W. T.↗
NASA NTRS1961

Laminar Heat-Transfer and Pressure Measurements at a Mach Number of 6 on Sharp and Blunt 15 deg Half-Angle Cones at Angles of Attack Up to 90 deg

Two circular conical configurations having 15 deg half-angles were tested in laminar boundary layer at a Mach number of 6 and angles of attack up to 90 deg. One cone had a sharp nose and a fineness ratio of 1.87 and the other had a spherically blunted nose with a bluntness ratio of 0.1428 and a fineness ratio of 1.66. Pressure measurements and schlieren pictures of the flow showed that near-conical flow existed up to an angle of attack of approximately 60 deg. At angles of attack above 70 deg high-pressure areas were present near the base and the bow shock wave was considerably curved. Comparison of the results with simply applied theories showed that on the stagnation line pressures may be predicted by Newtonian theory, and heat transfer by local yawed-cylinder theory based on the yaw angle of the windward generator and the local radius of the cone. Base effects increased the heat transfer in a region extending forward approximately 15 to 30 percent of the windward generator. Circumferential pressure distributions were higher than the corresponding Newtonian distribution and a better prediction was obtained by modifying the theory to match the pressure at 90 deg from the windward generator to that on the surface of the cone at an angle of attack of 0 deg. Circumferential heat-transfer distributions were predicted satisfactorily up to about 60 deg from the stagnation line by using Lees' heat-flux distribution based on the Newtonian pressure. The effects of nose bluntness at large angles of attack were very small in the region beyond two nose radii from the point of tangency.

Conti, Raul J.↗
NASA NTRS1993

Computation of crossing shock/turbulent boundary layer interaction at Mach 8.3

A three-dimensional (3D) hypersonic crossing shock wave/turbulent boundary-layer interaction is examined numerically at Mach 8.3. The test geometry consists of a pair of opposing sharp fins of angle alpha = 15 deg, mounted on a flat plate. Two theoretical models are evaluated. The full (3D) Reynolds-averaged Navier-Stokes equations are solved using the Baldwin-Lomax and the Rodi (modified k-epsilon) turbulence models. Computed results for both cases show good agreement with experiment for flat plate surface pressure and for flowfield profiles of pitot pressure and yaw angle, indicating that the flowfield is primarily rotational and inviscid. Fair to poor agreement is obtained for surface heat transfer, indicating a need for more accurate turbulence models. The overall flowfield structure is similar to that observed in previous crossing shock interaction studies.

Narayanswami, N.↗
NASA NTRS1993

Numerical simulation of crossing/turbulent boundary layer interaction at Mach 8.3 comparison of zero and two-equation turbulence models

A 3D hypersonic crossing shock wave/turbulent boundary layer interaction is examined numerically. The test geometry consists of a pair of opposing sharp fins of angle alpha = 15 deg mounted on a flat plate. The freestream Mach number is 8.28. Two theoretical models are evaluated. The full 3D Reynolds-averaged Navier-Stokes equations are solved using the Baldwin-Lomax algebraic turbulent eddy viscosity model and the Rodi turbulence model. Computed results for both cases show good agreement with experiment for flat plate surface pressure and for pitot pressure and yaw angle profiles in the flowfield. General agreement is obtained for surface flow direction. Fair to poor agreement is obtained for surface heat transfer, indicating a need for more accurate turbulence models. The overall flowfield structure is similar to that observed in previous crossing shock interaction studies.

Narayanswami, N.↗
NASA NTRS1989

Measurement resolution of noise directivity patterns from acoustic flight tests

The measurement resolution of noise directivity patterns from acoustic flight tests was investigated. Directivity angle resolution is affected by the data reduction parameters, the aircraft velocity and flyover altitude, and by deviations of the aircraft from the desired flight path. Equations are developed which determine bounds for the lateral and longitudinal directivity angle resolution as a function of the nominal directivity angle. The equations are applied to a flight test data base and the effects of several flight conditions and data reduction parameters on the directivity angle resolution are presented. The maximum directivity angle resolution typically occurs when the aircraft is at or near the overhead position. In general, directivity angle resolution improves with decreasing velocity, increasing altitude, increasing sampling rate, decreasing block size, and decreasing block averages. Deviations from the desired ideal flight path will increase the resolution. For the flight experiment considered in this study, an average of two flyovers were required at each test condition to obtain an acceptable flight path. The ability of the pilot to maintain the flight track improved with decreasing altitude, decreasing velocity, and practice. Due to the prevailing wind conditions, yaw angles of as much as 20 deg were required to maintain the desired flight path.

Conner, David A.↗
NASA NTRS1992

Structure of supersonic turbulent flow past a swept compression corner

The structure of the shock wave/turbulent boundary-layer interaction generated by a 3D swept compression corner has been investigated through a combined experimental and theoretical research program. The flowfield geometry is defined by the streamwise compression angle alpha and the sweep angle lambda of the corner. The present study examines two different configurations, namely (alpha, lambda) = (24 deg, 40 deg) and (24 deg, 60 deg) at Mach 3 and Re sigma infinity about 9 x 10 exp 5. The theoretical model is the 3D Reynolds-averaged compressible Navier-Stokes equations with turbulence incorporated using a turbulent eddy viscosity. The calculated flowfields display general agreement with experimental data for surface pressure and good agreement with experimental flowfield profiles of pitot pressure and yaw angle. The principal feature of the flowfield is a large vortical structure approximately aligned with the corner. The entrainment of incoming fluid into the vortical structure is strongly affected by the sweep angle lambda. Viscous (turbulent and molecular) effects appear to be important only in the immediate vicinity of the surface and in an isolated region within the interaction and near the corner.

Knight, Doyle D.↗
NASA NTRS1975

Geometric theory of horizon scanners

The note presents a general geometrical theory of spacecraft horizon scanners for the purpose of actual attitude determination, as opposed to just attitude stabilization. Analysis is carried out in terms of the scanning angles and three sets of auxiliary axes: the scanner axes, the nonscanning axes, and the orbital axes. Euler angles (yaw, pitch, and roll) transform the orbital axes to the nonscanning axes, and spacecraft attitude is determined directly from the attitude of the nonscanning axes relative to the orbital axes. In most applications the scanning speed is fast, so that it can be assumed that the attitude of the spacecraft does not change during a scan; however, a perturbation analysis is provided for errors committed by neglecting attitude changes. The analysis is valid for all types of scanners; in addition, the case where two scanners with different half-cone angles are used is considered.

Fang, B. T.↗
NASA NTRS1992

The hypersonic shock wave-turbulent boundary layer interaction generated by a sharp fin at Mach 8.2

A combined experimental and numerical study has been conducted on the hypersonic shock-wave turbulent-boundary layer interaction at Mach 8.2 generated by a single fin of angles alpha = 10 and 15 deg. Three models are considered: (1) the 3D compressible Reynolds-averaged Navier-Stokes (RANS) equations using the k-epsilon turbulence model, (2) the 3D RANS using the Rodi turbulence model, and (3) the conical RANS using the Baldwin-Lomax algebraic turbulence model. The computations are compared with various experimental data. The computations using models (1) and (2) show quantitatively very similar results and very good agreement with experimental data for surface pressure and skin friction. Comparison with boundary layer profiles of pitot pressure and yaw angle are also generally good, but the peak surface heat transfer is overestimated by up to 48 percent. The effect of the laminar boundary layer on the fin is restricted to the immediate vicinity of the fin surface. Conical calculations using model (3) show substantially poorer agreement with experiment.

Knight, Doyle D.↗
NASA NTRS1993

Characterization of cavity flow fields using pressure data obtained in the Langley 0.3-Meter Transonic Cryogenic Tunnel

Static and fluctuating pressure distributions were obtained along the floor of a rectangular-box cavity in an experiment performed in the LaRC 0.3-Meter Transonic Cryogenic Tunnel. The cavity studied was 11.25 in. long and 2.50 in. wide with a variable height to obtain length-to-height ratios of 4.4, 6.7, 12.67, and 20.0. The data presented herein were obtained for yaw angles of 0 deg and 15 deg over a Mach number range from 0.2 to 0.9 at a Reynolds number of 30 x 10(exp 6) per ft with a boundary-layer thickness of approximately 0.5 in. The results indicated that open and transitional-open cavity flow supports tone generation at subsonic and transonic speeds at Mach numbers of 0.6 and above. Further, pressure fluctuations associated with acoustic tone generation can be sustained when static pressure distributions indicate that transitional-closed and closed flow fields exist in the cavity. Cavities that support tone generation at 0 deg yaw also supported tone generation at 15 deg yaw when the flow became transitional-closed. For the latter cases, a reduction in tone amplitude was observed. Both static and fluctuating pressure data must be considered when defining cavity flow fields, and the flow models need to be refined to accommodate steady and unsteady flows.

Tracy, M. B.↗
NASA NTRS2004

An Experimental Study Synthetic Jets from Rectangular Orifices

Results of an experimental investigation on isolated synthetic jets in crossflow from rectangular orifices of different aspect ratio and orientation are presented. Three aspect ratios, AR = 4, 8, and 16, with pitch a = 90deg., were investigated, Additionally, the AR = 8 case was pitched at 20 deg.. The yaw angle, , was varied through 0 deg., 10 deg., 45 deg. and 90 deg.. All orifices had same exit area and the data were compared with synthetic as well as steady jet from a circular orifice of same area. Hotwire measurements were performed to obtain all three components of mean velocity and turbulent stresses. Data were acquired for momentum-flux ratio up to J = 50. Distributions of time- and phase-averaged data were obtained on the cross sectional plane at x/D = 0.5, 5 and 10, as well as on the axial plane of the symmetry. Qualitative flowfield similarity between synthetic and steady jets is observed. However, high-momentum 'cap' above the low-momentum 'dome', characteristic of steady jets, does not necessarily appear in the synthetic jet. The position and shape of the high-momentum region depend on the distance from the orifice, pitch, yaw as well as momentum-flux ratio. Consequently, the location of the minimum velocity in the 'dome' measured at the plane of symmetry, y(submin), is adopted as a reference for penetration estimate and trajectory comparison. For AR = 16, the dome is the largest in area with maximum velocity deficit. However, the penetration is somewhat higher for AR = 4. Increase in yaw reduces the spatial extent of the dome and the penetration height but augments the velocity deficit. At low J the dome is connected to the boundary layer and traces of the cap of high momentum fluid are visible above it. Increase in J lifts the dome and reorganizes the high-momentum fluid around its perimeter, eventually bringing it underneath. Phase-averaged data document dynamic topological changes within the cycle. Phase-averaged streamwise velocity contours on the cross-sectional plane exhibit behavior commensurate with that seen in time-averaged data at various J.

Milanovic, Ivana M.↗
NASA NTRS1972

In-orbit flexible spacecraft dynamics program

A continuous flexible body nonlinear dynamics computer program is used for simulating the spinning mode performance of a spacecraft under applied control torques. The program takes into account the continuous flexible nature of the antennas by representing deflections in terms of shape functions and integrated the spatial dependence in the formulation of the equations of motion. Comparison of RAE flight data on roll, pitch, and yaw with predictions of the computer program in the gravity gradient mode show fair to good agreement in roll and pitch and excellent agreement in the yaw angle.

Fedor, J. V.↗