Search NASA⌕ Search

SEARCH · Search NASA

Results for “Cyclic loading”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60

Prediction of elemental creep

Cyclic and steady-state creep tests were performed to provide data which were used to develop predictive equations. These equations, describing creep as a function of stress, temperature, and time, were developed through the use of a least squares regression analyses computer program for both the steady-state and cyclic data sets. Comparison of the data from the two types of tests, revealed that there was no significant difference between the cyclic and steady-state creep strains for the L-605 sheet under the experimental conditions investigated (for the same total time at load). Attempts to develop a single linear equation describing the combined steady-state and cyclic creep data resulted in standard errors of estimates higher than obtained for the individual data sets. A proposed approach to predict elemental creep in metals uses the cyclic creep equation and a computer program which applies strain and time hardening theories of creep accumulation.

Davis, J. W.↗

A crack-closure model for predicting fatigue crack growth under aircraft spectrum loading

The present paper is concerned with the development and application of an analytical model of cyclic crack growth that includes the effects of crack closure. The model was based on a concept like the Dugdale model, but was modified to leave plastically deformed material in the wake of the advancing crack tip. The model was used to correlate crack growth rates under constant-amplitude loading and to predict crack growth under aircraft spectrum loading on 2219-T851 aluminum alloy plate material. The predicted crack growth lives agreed well with experimental data. The ratio of predicted-to-experimental lives ranged from 0.66 to 1.48.

Newman, J. C., Jr.↗

High temperature inelastic deformation of the B1900 + Hf alloy under multiaxial loading - Theory and experiment

The multiaxial deformation behavior of the Ni-based alloy B1900 + Hf has been studied at elevated temperatures in the range of 649-982 C. Combined tension/torsion cyclic tests were performed on thin-wall tubular specimens under both in-phase and out-of-phase strain-controlled loading cycles. Both straining conditions resulted in stress loci of comparable magnitude, exhibiting no difference in cyclic hardening response. A phase angle was observed between the deviatoric stress and the incremental plastic strain vectors during 90-deg out-of-phase strain cycling, and nonproportional stress relaxation occurred under biaxial strain hold. The overall results have been used to assess the flow law, the hardening equations, and the applicability of the J2-based, elastic-viscoplastic model of Bodner-Partom (1979) for multiaxial loading conditions. The overall agreement between theory and experiment is good. Discrepancies are discussed in relation to micromechanical considerations.

Chan, K. S.↗

Sensitivity of acoustic predictions to variation of input parameters

The noise prediction code WOPWOP predicts the thickness and loading noise produced by a helicopter rotor, given the blade motion, rotor operating conditions, and fluctuating force distribution over the blade surface. However, the criticality of these various inputs, and their respective effects on the predicted acoustic field, have never been fully addressed. This paper examines the importance of these inputs, and the sensitivity of the acoustic predictions to a variation of each parameter. The effects of collective and cyclic pitch, as well as coning and flapping, are presented. Blade loading inputs are examined to determine the necessary spatial and temporal resolution, as well as the importance of the cordwise distribution. The acoustic predictions show regions in the acoustic field where significant errors occur when simplified blade motions or blade loadings are used. An assessment of the variation in the predicted acoustic field is balanced by a consideration of CPU time necessary for the various approximations.

Brentner, Kenneth S.↗

Loading Path Dependence of Forming Limit Diagram of a TRIP800 Steel

In this paper, the microstructure-based finite element modeling method is used in investigating the loading path dependence of formability of transformation induced plasticity (TRIP) steels. For this purpose, the effects of different loading path on the forming limit diagrams (FLD) of TRIP steels are qualitatively examined using the representative volume element (RVE) of a commercial TRIP800 steel. First, the modeling method was introduced, where a combined isotropic/kinematic hardening rule is adopted for the constituent phases in order to rightly describe the cyclic deformation behaviors of TRIP steels during the forming process with combined loading paths which may include the unloading between the two consecutive loadings. Material parameters for the constituent phases remained the same as those in the authors’ previous study [1] except for some adjustments for the martensite phase due to the introduction of the new combined hardening rule. Based on the new material parameters and new hardening rule, the predicted deformation behaviors of the TRIP800 steel show quite similar qualitative trends to those reported in other experimental works. Pseudo-forming limit strain diagrams (Pseudo-FLD) for the TRIP800 steel were, then, obtained for various loading paths. The computational results show that, similar to other single phase materials, the TRIP800 steel shows very sensitive loading path dependence in the strain-based forming limit diagrams (strain-FLD), but does not in the stress-based forming limit diagrams (stress-FLD), and that the phase transformation does not have significant effects on the FLD for the TRIP800 steel. From the observations in this study, the current modeling methods can be used in examining the qualitative trends of FLD of TRIP steels under different loading paths/prestrains.

Forming limit diagram↗

Matrix Fatigue Cracking Mechanisms of Alpha(2) TMC for Hypersonic Applications

The objective of this work was to understand matrix cracking mechanisms in a unidirectional alpha(sub 2) TMC in possible hypersonic applications. A (0)(sub 8) SCS-6/Ti-24Al-11Nb (at. percent) TMC was first subjected to a variety of simple isothermal and nonisothermal fatigue cycles to evaluate the damage mechanisms in simple conditions. A modified ascent mission cycle test was then performed to evaluate the combined effects of loading modes. This cycle mixes mechanical cycling at 150 and 483 C, sustained loads, and a slow thermal cycle to 815 C. At low cyclic stresses and strains more common in hypersonic applications, environment-assisted surface cracking limited fatigue resistance. This damage mechanism was most acute for out-of-phase nonisothermal cycles having extended cycle periods and the ascent mission cycle. A simple linear fraction damage model was employed to help understand this damage mechanism. Time-dependent environmental damage was found to strongly influence out-of-phase and mission life, with mechanical cycling damage due to the combination of external loading and CTE mismatch stresses playing a smaller role. The mechanical cycling and sustained loads in the mission cycle also had a smaller role.

Gabb, Timothy P.↗

Parametric analysis of a passive cyclic control device for helicopters

A parametric study of a passive device which provides a cyclic longitudinal control moment for a helicopter rotor was performed. It utilizes a rotor blade tip which is structurally decoupled from the blade inboard section. This rotor configuration is generally called the Free-Tip Rotor. A two dimensional numerical model was used to review the Constant Lift Tip Rotor, a predecessor of the current configuration, and then the same model was applied to the Passive Cyclic Control Device. The Constant Lift Tip was proven to have the ability to suppress the vibratory lift loading on the tip around the azimuth and to eliminate a significant negative lift peak on the advancing tip. The Passive Cyclic Control Device showed a once-per-revolution lift oscillation with a large amplitude, while minimizing the higher harmonic terms of the lift oscillation. This once-per-revolution oscillation results in the cyclic moment to trim the rotor longitudinally. A rotor performance analysis was performed by a three dimensional numerical model. It indicated that the vortices shed from the junction between the tip and the inboard section has a strong influence on the tip, and it may severely limit the tip performance. It was also shown that the Free-Tip allows the inboard section to have a larger twist, which results in a better performance.

Kumagai, H.↗

Universal Mechanism of Viscoplastic Deformation of Metallic Materials Far from Thermodynamics Equilibrium

The article gives results of structure formation in metallic materials after different types of deformation: tungsten after rolling, nickel after thermal cycling and nickel single crystal after rolling, aluminum single crystal after cyclic tension and aluminum alloys (D16, 2024-T3) after impulsive load. We used optical and electron microscopy methods for investigation of deformation structure formation and molecular dynamics method for computer modeling of the processes of plastic deformation (LAMMPS software). The following quantitative parameters were calculated during the simulation: energy of pair interaction, temperature, total cumulative pressure, stress tensor and pressure tensor. The study shows that the plastic flow of metallic materials with any initial structure at certain loading stage can be carried out by homogeneous mass transfer through channels with a liquid-like structure, from which follows that the dislocation mechanism of plastic deformation of crystals has a limited field of application. The main role has a synergistic structure formation in the conditions of distance from thermodynamic equilibrium. The relaxation processes proceed intensively after and during the process of destruction. The results of modeling have shown the possibility of forming channels of hydrodynamic flow without the participation of defects in the initial material.

36 MATERIALS SCIENCE↗

PPO foam - Liquid hydrogen insulation

An extensive fabrication and test program is described which has demonstrated the integrity of PPO (polyphenylene oxide) foam as an internal insulation. PPO is shown to be capable of withstanding multiple reuses on such cryogenic-fueled launch vehicles as the Space Shuttle. The major advantages of this internal insulation is the absence of a pressure load on the insulation, reduced handling damage, and minimization of cyclic thermal stresses by a 'warm' bond line.

Yates, G. B.↗

Fatigue life of organic fiber/epoxy pressure vessels

The cyclic fatigue life of 10.2-cm-diam cylindrical pressure vessels has been studied. The vessels were made of an organic fiber/epoxy composite. To determine the typical strength distribution of the vessels, 25 of them were internally pressurized until they burst. Twenty-five vessels were then tested under sinusoidal cycling at 1 Hz between 4% and 91% of the mean burst strength. An additional twenty-five vessels were tested between 4% and 91% with a rectangular pressure pulse at 1/3 Hz. A limited number of vessels were tested for stress rupture at the 91% level. Cyclic life was found to depend on time at peak load as well as the number of stress cycles.

Hamstad, M. A.↗

Elastic Properties in Tension and Shear of High Strength Nonferrous Metals and Stainless Steel - Effect of Previous Deformation and Heat Treatment

A resume is given of an investigation of the influence of plastic deformation and of annealing temperature on the tensile and shear elastic properties of high strength nonferrous metals and stainless steels in the form of rods and tubes. The data were obtained from earlier technical reports and notes, and from unpublished work in this investigation. There are also included data obtained from published and unpublished work performed on an independent investigation. The rod materials, namely, nickel, monel, inconel, copper, 13:2 Cr-Ni steel, and 18:8 Cr-Ni steel, were tested in tension; 18:8 Cr-Ni steel tubes were tested in shear, and nickel, monel, aluminum-monel, and Inconel tubes were tested in both tension and shear. There are first described experiments on the relationship between hysteresis and creep, as obtained with repeated cyclic stressing of annealed stainless steel specimens over a constant load range. These tests, which preceded the measurements of elastic properties, assisted in devising the loading time schedule used in such measurements. From corrected stress-set curves are derived the five proof stresses used as indices of elastic or yield strength. From corrected stress-strain curves are derived the secant modulus and its variation with stress. The relationship between the forms of the stress-set and stress-strain curves and the values of the properties derived is discussed. Curves of variation of proof stress and modulus with prior extension, as obtained with single rod specimens, consist in wavelike basic curves with superposed oscillations due to differences of rest interval and extension spacing; the effects of these differences are studied. Oscillations of proof stress and modulus are generally opposite in manner. The use of a series of tubular specimens corresponding to different amounts of prior extension of cold reduction gave curves almost devoid of oscillation since the effects of variation of rest interval and extension spacing were removed. Comparison is also obtained between the variation of the several properties, as measured in tension and in shear. The rise of proof stress with extension is studied, and the work-hardening rates of the various metals evaluated. The ratio between the tensile and shear proof stresses for the various annealed and cold-worked tubular metals is likewise calculated. The influence of annealing or tempering temperature on the proof stresses and moduli for the cold-worked metals and for air-hardened 13:2 Cr-Ni steel is investigated. An improvement of elastic strength generally is obtained, without important loss of yield strength, by annealing at suitable temperature. The variation of the proof stress and modulus of elasticity with plastic deformation or annealing temperature is explained in terms of the relative dominance of three important factors: namely, (a) internal stress, (b) lattice-expansion or work-hardening, and (c) crystal reorientation. Effective values of Poisson's ratio were computed from tensile and shear moduli obtained on tubular specimens. The variation of Poisson's ratio with plastic deformation and annealing temperature is explained in terms of the degree of anisotropy produced by changes of (a) internal stress and (b) crystal orientation.

METALS - ELASTICITY↗

High Temperature Tensile Properties and Fatigue Behavior of a Melt-Infiltrated SiC/SiC Composite

High temperature fatigue behavior of a woven, SiC/SiC ceramic matrix composite (CMC) was investigated in air at two temperatures. The reinforcement for the CMC consisted of 5HS Sylramic(Trademark) fabric with a [0deg/90deg]4s lay-up. The SiC matrix material was infiltrated into the fiber-preform with a slurry-cast, melt-infiltration process. Tensile and fatigue test specimens were machined from the CMC plates. Initially tensile tests were conducted to obtain the average values of tensile properties at 1038 and 1204 C. Subsequently, low-cycle fatigue (LCF) tests with zero and two-hour hold-times at the maximum stress were conducted at the same two temperatures. Fatigue life data generated in the LCF tests were used to determine the geometric mean fatigue lives. In this paper, the tensile behavior and the fatigue durability of the CMC determined under different loading conditions are documented. In addition, reductions observed in the cyclic lives of the composite due to the two hour hold-time at maximum tensile stress are discussed.

Kalluri, Sreeramesh↗

Wind turbine blade testing system using base excitation

An apparatus (500) for fatigue testing elongate test articles (404) including wind turbine blades through forced or resonant excitation of the base (406) of the test articles (404). The apparatus (500) includes a testing platform or foundation (402). A blade support (410) is provided for retaining or supporting a base (406) of an elongate test article (404), and the blade support (410) is pivotally mounted on the testing platform (402) with at least two degrees of freedom of motion relative to the testing platform (402). An excitation input assembly (540) is interconnected with the blade support (410) and includes first and second actuators (444, 446, 541) that act to concurrently apply forces or loads to the blade support (410). The actuator forces are cyclically applied in first and second transverse directions. The test article (404) responds to shaking of its base (406) by oscillating in two, transverse directions (505, 507).

42 ENGINEERING↗

PREDICTION OF CYCLIC VARIABILITY AND KNOCK-LIMITED SPARK ADVANCE (KLSA) IN SPARK-IGNITION (SI) ENGINE

Engine knock remains one of the major barriers to further improve the thermal efficiency of spark-ignition (SI) engines. SI engine is usually operated at knock-limited spark advance (KLSA) to achieve possibly maximum efficiency with given engine hardware and fuel properties. Co-optimization of fuels and engines is promising to improve engine efficiency, and predictive computational fluid dynamics (CFD) models can be used to facilitate this process. However, cyclic variability of SI engine demands that multi cycle results are required to capture the extreme conditions. In addition, Mach Courant Friedrichs-Lewy (CFL) number of 1 is desired to accurately predict the knock intensity (KI), resulting in unaffordable computational cost. In this study, a new approach to numerically predict KLSA using large Mach CFL of 50 with ten consecutive cycle simulation is proposed. This approach is validated against the experimental data for a boosted SI engine at multiple loads and spark timings with good agreements in terms of cylinder pressure, combustion phasing, and cyclic variation. Engine knock is predicted with early spark timing, indicated by significant pressure oscillation and end-gas heat release. Maximum amplitude of pressure oscillation analysis is performed to quantify the KI, and the slope change point in KI extrema is used to indicate the KLSA accurately. Using a smaller Mach CFL number of 5 also results in the same conclusions, thus demonstrating that this approach is insensitive to the Mach CFL number. The use of large Mach CFL number allows us to achieve fast turn-around time for multicycle engine CFD simulations.

CCV↗

Torsional and biaxial (tension-torsion) fatigue damage mechanisms in Waspaloy at room temperature

Strain controlled torsional and biaxial (tension-torsion) low cycle fatigue behavior of Waspaloy was studied at room temperature as a function of heat treatment. Biaxial tests were conducted under proportional and nonproportional cyclic conditions. The deformation behavior under these different cyclic conditions was evaluated by slip trace analysis. For this, a Schmidt-type factor was defined for multiaxial loading conditions, and it was shown that when the slip deformation is predominant, nonproportional cycles are more damaging than proportional or pure axial or torsional cycles. This was attributed to the fact that under nonproportional cyclic conditions, deformation was through multiple slip, as opposed to single slip for other loading conditions, which gave rise to increased hardening. The total life for a given test condition was found to be independent of heat treatment. This was interpreted as being due to the differences in the cycles to initiation and propagation of cracks.

Jayaraman, N.↗

Evaluation of the cyclic behavior of aircraft turbine disk alloys, part 2

Several nickel-base aircraft turbine disk superalloys were evaluated at 650 C for resistance to fatigue crack initiation and propagation under cyclic and cyclic/dwell conditions. Controlled strain low cycle fatigue (LCF) and controlled load crack propagation tests were performed and results utilized to provide a direct comparison among the alloys. Tests were performed on selected alloys to evaluate the effects of hold times, mean stresses, stress-dwell cycle types, inert environment, and contractor test methods. At the lower total strain ranges of interest, the alloys exhibited generally increasing initiation life with increasing tensile strength for both cyclic (0.33 Hz) and cyclic/dwell (900-sec hold per cycle) conditions. Rank order of the alloys by LCF initiation life changed substantially at higher strain ranges, approaching the rank order expected from monotonic tensile ductilities. The effect of the 900 sec (15 min) hold time fatigue life varied significantly from alloy to alloy. Generally, the higher-strength, finer-grained alloys exhibited more significant reductions in fatigue life due to the dwell. The effects of mean strain were found to be negligible and the effects of mean stress were pronounced. At high strain ranges the mean stress was near zero and did not contribute to reduction in life. At low strain ranges, however, mean stresses were large and significant reductions in LCF lives occurred.

Cowles, B. A.↗

Cyclic Fatigue of Brittle Materials with an Indentation-Induced Flaw System

The ratio of static to cyclic fatigue life, or 'h ratio', was obtained numerically for an indentation flaw system subjected to sinusoidal loading conditions. Emphasis was placed on developing a simple, quick lifetime prediction tool. The solution for the h ratio was compared with experimental static and cyclic fatigue data obtained from as-indented 96 wt.% alumina specimens tested in room-temperature distilled water.

Choi, Sung R.↗

Microstructure: Property correlation

Strain controlled torsional and biaxial (tension-torsion) low cycle fatigue behavior of Waspaloy was studied at room temperature as a function of heat treatment. Biaxial tests were conducted under proportional (when the axial and torsional strain cycles are in-phase) and non-proportional (when the axial and torsional strain cycles are 90 deg out-of-phase) cyclic conditions. The deformation behavior under these different cyclic conditions were evaluated by slip trace analysis. For this, a Schmidt-type factor was defined for multiaxial loading conditions and it was shown that when the slip deformation is predominant, non-proportional cycles are more damaging than proportional or pure axial or torsional cycles. This was attributed to the fact that under non-proportional cyclic conditions, deformation was through multiple slip as opposed single slip for other loading conditions, which gave rise to increased hardening. The total life for a given test condition was found to be independent of heat treatment. This was interpreted as being due to the differences in the cycles to initiation and propagation of cracks.

Jayaraman, N.↗