Search NASA⌕ Search

SEARCH · Search NASA

Results for “DRILL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60

Basic Data Report for Piezometers PZ-13, PZ-14, and PZ-15 and Shallow Subsurface Water

The Site and Preliminary Design Validation (SPDV) pile is located in the southwest corner of Section 21, Township 22 South, Range 31 East in Eddy County, New Mexico, adjacent to the Waste Isolation Pilot Plant (WIPP) operational area. During August 2007, piezometers (PZ)-13, PZ-14, and PZ-15 were drilled around the SPDV pile to determine if shallow subsurface water (SSW) existed around the SPDV pile and, if so, provide a means to monitor. These piezometers were drilled with a combination of hollow-stem auger and air-assisted hollow-stem auger drilling. Below the surficial dunes and Berino soil, piezometers PZ-13 and PZ-14 encountered in order, from shallowest to deepest, the Mescalero caliche, Gatuña Formation, Santa Rosa Formation, and Dewey Lake Formation. Piezometer PZ-15 was completed in the Gatuña Formation, having not encountered the lower formations by the time SSW was detected. Water was encountered in all wells. Piezometers were constructed of 2-inch polyvinyl chloride casing and 15 feet of 0.020-inch slot screen. Water samples were obtained and analyzed for each well. Based on the results of the installation of the piezometers, analysis of water levels, and geological analysis, it is concluded that the water levels identified in PZ-13 and PZ-14 are the result of the SPDV pile runoff or infiltration prior to being lined. Water in PZ-15 is much shallower and chemically different that water in the other two wells, indicating another source, such as recharge and infiltration from the east of the SPDV pile.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Basic Data Report for Piezometers PZ-13, PZ-14, and PZ-15, and Shallow Subsurface Water (Rev. 1)

The Site and Preliminary Design Validation (SPDV) pile is located in the southwest corner of Section 21, Township 22 South, Range 31 East in Eddy County, New Mexico, adjacent to the Waste Isolation Pilot Plant (WIPP) operational area. During August 2007, piezometers (PZ)-13, PZ-14, and PZ-15 were drilled around the SPDV pile to determine if shallow subsurface water (SSW) existed around the SPDV pile and, if so, provide a means to monitor. These piezometers were drilled with a combination of hollow-stem auger and air-assisted hollow-stem auger drilling. Below the surficial dunes and Berino soil, piezometers PZ-13 and PZ-14 encountered in order, from shallowest to deepest, the Mescalero caliche, Gatuña Formation, Santa Rosa Formation, and Dewey Lake Formation. Piezometer PZ-15 was completed in the Gatuña Formation, having not encountered the lower formations by the time SSW was detected. Water was encountered in all wells. Piezometers were constructed of 2-inch polyvinyl chloride casing and 15 feet of 0.020-inch slot screen. Water samples were obtained and analyzed for each well. Based on the results of the installation of the piezometers, analysis of water levels, and geological analysis, it is concluded that the water levels identified in PZ-13 and PZ-14 are the result of the SPDV pile runoff or infiltration prior to being lined. Water in PZ-15 is much shallower and chemically different that water in the other two wells, indicating another source, such as recharge and infiltration from the east of the SPDV pile.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Basic Data Report for Piezometers PZ-13, PZ-14, and PZ-15, and Shallow Subsurface Water (Rev. 2)

The Site and Preliminary Design Validation (SPDV) pile is located in the southwest corner of Section 21, Township 22 South, Range 31 East in Eddy County, New Mexico, adjacent to the Waste Isolation Pilot Plant (WIPP) operational area. During August 2007, piezometers (PZ)-13, PZ-14, and PZ-15 were drilled around the SPDV pile to determine if shallow subsurface water (SSW) existed around the SPDV pile and, if so, provide a means to monitor. These piezometers were drilled with a combination of hollow-stem auger and air-assisted hollow-stem auger drilling. Below the surficial dunes and Berino soil, piezometers PZ-13 and PZ-14 encountered in order, from shallowest to deepest, the Mescalero caliche, Gatuña Formation, Santa Rosa Formation, and Dewey Lake Formation. Piezometer PZ-15 was completed in the Gatuña Formation, having not encountered the lower formations by the time SSW was detected. Water was encountered in all wells. Piezometers were constructed of 2-inch polyvinyl chloride casing and 15 feet of 0.020-inch slot screen. Water samples were obtained and analyzed for each well. Based on the results of the installation of the piezometers, analysis of water levels, and geological analysis, it is concluded that the water levels identified in PZ-13 and PZ-14 are the result of the SPDV pile runoff or infiltration prior to being lined. Water in PZ-15 is much shallower and chemically different that water in the other two wells, indicating another source, such as recharge and infiltration from the east of the SPDV pile.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Basic Data Report for Piezometers PZ-13, PZ-14, and PZ-15, and Shallow Subsurface Water (Rev. 3)

The Site and Preliminary Design Validation (SPDV) pile is located in the southwest corner of Section 21, Township 22 South, Range 31 East in Eddy County, New Mexico, adjacent to the Waste Isolation Pilot Plant (WIPP) operational area. During August 2007, piezometers (PZ)-13, PZ-14, and PZ-15 were drilled around the SPDV pile to determine if shallow subsurface water (SSW) existed around the SPDV pile and, if so, provide a means to monitor. These piezometers were drilled with a combination of hollow-stem auger and air-assisted hollow-stem auger drilling. Below the surficial dunes and Berino soil, piezometers PZ-13 and PZ-14 encountered in order, from shallowest to deepest, the Mescalero caliche, Gatuña Formation, Santa Rosa Formation, and Dewey Lake Formation. Piezometer PZ-15 was completed in the Gatuña Formation, having not encountered the lower formations by the time SSW was detected. Water was encountered in all wells. Piezometers were constructed of 2-inch polyvinyl chloride casing and 15 feet of 0.020-inch slot screen. Water samples were obtained and analyzed for each well. Based on the results of the installation of the piezometers, analysis of water levels, and geological analysis, it is concluded that the water levels identified in PZ-13 and PZ-14 are the result of the SPDV pile runoff or infiltration prior to being lined. Water in PZ-15 is much shallower and chemically different that water in the other two wells, indicating another source, such as recharge and infiltration from the east of the SPDV pile.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

CT Scans of Cores Metadata, Utqiagvik (Barrow), Alaska, 2015

Individual ice cores were collected from Barrow Environmental Observatory in Barrow, Alaska, throughout 2013 and 2014. Cores were drilled along different transects to sample polygonal features (i.e. the trough, center and rim of high, transitional and low center polygons). Most cores were drilled around 1 meter in depth and a few deep cores were drilled around 3 meters in depth. Three-dimensional images of the frozen cores were constructed using a medical X-ray computed tomography (CT) scanner. TIFF files can be uploaded to ImageJ (an open-source imaging software) to examine soil structure and soil densities within each core.The Next-Generation Ecosystem Experiments: Arctic (NGEE Arctic), was a 15-year research effort (2012-2027) to reduce uncertainty in Earth System Models by developing a predictive understanding of carbon-rich Arctic ecosystems and feedbacks to climate. NGEE Arctic was supported by the Department of Energy's Office of Biological and Environmental Research.The NGEE Arctic project had two field research sites: 1) located within the Arctic polygonal tundra coastal region on the Barrow Environmental Observatory (BEO) and the North Slope near Utqiagvik (Barrow), Alaska and 2) multiple areas on the discontinuous permafrost region of the Seward Peninsula north of Nome, Alaska.Through observations, experiments, and synthesis with existing datasets, NGEE Arctic provided an enhanced knowledge base for multi-scale modeling and contributed to improved process representation at global pan-Arctic scales within the Department of Energy's Earth system Model (the Energy Exascale Earth System Model, or E3SM), and specifically within the E3SM Land Model component (ELM).

54 ENVIRONMENTAL SCIENCES↗

Analysis of Rotary Steerable Systems versus Conventional Mud Motors for Vertical and Horizontal Wells in the Caney Formation, Southwest Oklahoma

Rotary steerable systems (RSS) have transformed directional drilling over the years and are becoming widely accepted throughout the world. RSS technology has been proven to provide the required strength and agility in challenging and abrasive environments as well as provide a higher rate of penetration (ROP) by allowing more weight transfer to the bit. Due to the higher price of RSS, some companies have stayed loyal to the conventional bent housing (CBH) with a performance drilling motor, regardless of the RSS benefits. This paper examines the performance and cost benefits of standalone RSS (SA-RSS), motor driven RSS (MD-RSS), and CBH systems. Three wells drilled in the Caney formation in Southwestern Oklahoma were selected for the analysis. Results showed that using RSS in the 12.25” intermediate vertical section and the 8.75”/8.5” lateral section was more cost effective than a CBH system. The cost per foot for the CBH was 1.6 to 2.3 times higher than RSS in the vertical section and 1.7 times higher in the lateral section. The RSS ROP was 2.3 to 4.8 times faster than CBH in the vertical section and 1.6 times faster in the lateral section.

Hayes, John↗

Produced Fluid Induced Mineralogy and Elemental Alterations of Caney Shale, Southern Oklahoma

ABSTRACT This study involves batch reactor experiments and subsequent analyses of samples from Caney Shale in the Ardmore Basin of South-Central Oklahoma. Samples include mainly rock cores and cuttings recovered from two wells respectively drilled vertically through and horizontally across the Caney Shale. Mineralogical compositions are obtained by X-Ray Diffraction (XRD) measurements whilst microstructure and elemental distribution are acquired by Scanning Electron Microscopy/Energy Dispersive Spectroscopy (SEM/EDS) respectively. Batch experiments are then conducted using selected rock samples and produced fluid from the Caney Formation. Deionized water is also reacted with some samples to serve as standard. Experiments are conducted at 95°C and ambient pressure for 7 and 30 days to assess the geochemical rock-fluid interactions. Results show rock mineralogical compositions are predominantly quartz, feldspar, carbonates, and clay with minor pyrite. Post-experimental mineralogical changes observed in samples include increased amorphous entities especially within the clay portions of XRD plots and dissolution of feldspar and carbonate minerals and formation of new mineral phases, mostly clays and salts. These are corroborated by EDS elemental analyses which show decreased elemental compositions. The implications of reactions mentioned above include but not limited to, scale formation, clay fines migration and shale softening all of which pose significant permeability impairment on formation over time. INTRODUCTION Shale reservoirs account for a large share of unconventional reservoirs in the world (Lyu et al., 2015). However, ultra-low permeability and high clay compositions pose significant challenges when producing from these reservoirs (Dawuda and Srinivasan, 2022, 2023). Producing from these reservoirs therefore requires horizontal drilling and hydraulic fracturing technologies which have proven their efficacy in generating substantial permeability in reservoirs to ensure production (Fujian et al., 2019; Liu et al., 2018). Even after expensive horizontal drilling and hydraulic fracturing, geochemical reactions between engineered fluids and formation leads to fracture constriction and adversely impact petrophysical properties (permeability and porosity) of the reservoir. These technologies are therefore under constant development and improvement in various aspects to ensure fine tuning for specific reservoirs. Under present conditions, much of the hydrocarbon reserves in unconventional shale reservoirs are left unproduced due to rapid decline in permeability following resumption to production after hydraulic fracturing. It is therefore essential to understand the range of geochemical reactions that cause rapid depletion of permeability after hydraulic fracturing and apply these to each shale reservoir to ensure substantial recovery rates.

Awejori, G. A.↗

3D Play Fairway Analysis for Examining of Superhot Reservoir Production Scenarios

The DEEPEN (DE-risking Exploration for geothermal Plays in magmatic ENvironments) project was a multi-laboratory, international effort to reduce uncertainty and improve resource characterization in superhot geothermal systems. Building on this foundation, this work advances open-source tools designed to lower the exploration risk and cost of superhot geothermal projects while promoting transparency, reproducibility, and efficiency in exploration workflows. These tools are being tested at two key sites: (1) the Nesjavellir Geothermal Area in Iceland, where the Icelandic Deep Drilling Project (IDDP) will drill its third well, and (2) Newberry Volcano in Oregon, USA, where Mazama Energy will pilot the first superhot enhanced geothermal system (EGS). A major outcome is the creation of a modular, open-source Python framework for play fairway analysis (PFA) in 2D and 3D, called geoPFA. The PFA workflow has been expanded to produce pseudo conceptual models, and will soon be refined to assess reservoir components through integration with the thermo-hydraulic-mechanical-chemical (THMC) simulator TReactMech, to enable iterative coupling between PFA and THMC models, improving characterization of superhot systems. All three of the Icelandic Deep Drilling Project's production scenarios were analyzed via this framework: (1) a superhot deep injection well paired with conventional production wells at Nesjavellir, (2) a superhot deep production well at Nesjavellir, and (3) superhot enhanced geothermal system at Newberry Volcano. This analysis provides useful insights around conceptual modeling of these production scenarios, helping to inform decisions around which scenario is best suited for which types of environments.

15 GEOTHERMAL ENERGY↗

Technique for anchoring fasteners to honeycomb panels

Two-piece fastener bushing provides mounting surface for components on a three-inch thick honeycomb structure. Specially constructed starter drill and sheet metal drill permit drilling without misalignment. Tapered knife-edge cutting tool removes honeycomb core material without tearing the adjacent material.

Brown, W. J.↗

Application of ERTS and EREP images to geologic investigations of the basin and range: Colorado plateau boundary in northwestern and north-central Arizona

The author has identified the following significant results. In the course of the ERTS investigation in the Cataract Creek Basin of the Coconino Plateau it was recognized that shallow perched ground water associated with the Kaibab Limestone could be discovered by means of drilling guided by geologic mapping aided by the use of ERTS imagery. At the Globe Ranch, the perched water table is only 5 meters beneath the surface at the site of the original, hand dug well. Recharge occurs from local runoff and from direct precipitation on the outcrop belt of the sandstone. This well provides water for the ranch at the rate of about 1,000 gallons a week. In order to explore the possibility of further developing this aquifer, unit 5 was mapped over an area of about 50 square miles in the vicinity of the hand-dug well, with negative results. A new location was then picked for drilling based on the occurrence of unit 5 in a favorable structural setting. This location was along a normal fault, and it was anticipated that water might be structurally trapped within the down-dropped block of the fault. Four shallow testholes were drilled and all encountered water. These four water-bearing holes are currently being monitored and will be tested to determine potential production of water from the local sandstone aquifer.

Goetz, A. F. H.↗

Ar-40/Ar-36 variations in Apollo 15 and 16 regolith

Values of Ar-40/Ar-36 have been determined for a large number of Apollo 15 and Apollo 16 fines, including samples from a range of depths in the Apollo 15 and 16 deep drill cores. Most of the Ar-40 in these samples is 'excess Ar-40' in that it has not been produced by in situ decay of K. Values of Ar-40/Ar-36 range from 0.74 to 4.35 and demonstrate that the regolith is not well mixed over depths of several cm or over surface distances greater than about 100 m. However, fines collected over surface distances of less than a few tens of meters tend to possess similar ratios. Values of Ar-40/Ar-36 in the Apollo 15 drill core increase with depth by nearly a factor of four (0.74 to 2.86) in the 0 to 80 cm depth range, then decrease for greater depths. Values of Ar-40/Ar-36 in the Apollo 16 drill core are nearly constant at about 1.3, except for the deepest sample analyzed (about 2.7). Concentrations of glass-bonded agglutinate particles in the fines tend to correlate with lower Ar-40/Ar-36, and may indicate that dynamic regolith processes also affect the trapped Ar-40/Ar-36.

Bogard, D. D.↗

The Marysville, Montana Geothermal Project

Drilling the first geothermal well in Montana presented many challenges, not only in securing materials and planning strategies for drilling the wildcat well but also in addressing the environmental, legal, and institutional issues raised by the request for permission to explore a resource which lacked legal definition. The Marysville Geothermal Project was to investigate a dry hot rock heat anomaly. The well was drilled to a total depth of 6790 feet and many fractured water bearing zones were encountered below 1800 feet.

Mcspadden, W. R.↗

Automatic Collection of Rock and Soil Samples

Proposed machine would sample rock or soil automatically. Mounted on a wheeled or tracked vehicle, machine positions drill for cut at any angle from horizontal to vertical, moves power head to drive drill into cut, and stores drilled core in a container. New concept may also be useful in terrestrial agricultural and geologic surveys.

Kyrias, G. M.↗

Mechanical Coal-Face Fracturer

Radial points on proposed drill bit take advantage of natural fracture planes of coal. Radial fracture points retracted during drilling and impacted by piston to fracture coal once drilling halts. Group of bits attached to array of pneumatic drivers to fracture large areas of coal face.

Collins, E. R., Jr.↗

Advanced composite aileron for L-1011 transport aircraft: Aileron manufacture

The fabrication activities of the Advanced Composite Aileron (ACA) program are discussed. These activities included detail fabrication, manufacturing development, assembly, repair and quality assurance. Five ship sets of ailerons were manufactured. The detail fabrication effort of ribs, spar and covers was accomplished on male tools to a common cure cycle. Graphite epoxy tape and fabric and syntactic epoxy materials were utilized in the fabrication. The ribs and spar were net cured and required no post cure trim. Material inconsistencies resulted in manufacturing development of the front spar during the production effort. The assembly effort was accomplished in subassembly and assembly fixtures. The manual drilling system utilized a dagger type drill in a hydraulic feed control hand drill. Coupon testing for each detail was done.

Dunning, E. G.↗

Primary sedimentary structures and the internal architecture of a Martian sand body in search of evidence for sand transport and deposition

Lunar experiences show that unmanned sample return missions, despite limitations on sample size, can produce invaluable data to infer crustal processes, regolith processes, regolith-atmosphere/ionosphere interaction processes, etc. Drill cores provide a record of regolith evolution as well as a more complete sample of the regolith than small scoops and/or rakes. It is proposed that: (1) a hole be drilled in a sand body to obtain continuous oriented cores; a depth of about 10 m would be compatible with what we know of bed form hierarchy of terrestrial stream deposits; (2) two trenches, at right angles to each other and close to the drill-hole, be dug and the walls scraped lightly such that primary/internal sedimentary structures of the sand body become visible; (3) the walls of the trenches be made gravitationally stable by impregnation techniques; (4) acetate or other peels of a strip on each wall be taken; and (5) appropriately scaled photographs of the walls be taken at different sun-angles to ensure maximum ease of interpretation of sedimentary structures; and, to correlate these structural features with those in the core at different depth levels of the core.

Basu, Abhijit↗

A core handling device for the Mars Sample Return Mission

A core handling device for use on Mars is being designed. To provide a context for the design study, it was assumed that a Mars Rover/Sample Return (MRSR) Mission would have the following characteristics: a year or more in length; visits by the rover to 50 or more sites; 100 or more meter-long cores being drilled by the rover; and the capability of returning about 5 kg of Mars regolith to Earth. These characteristics lead to the belief that in order to bring back a variegated set of samples that can address the range of scientific objetives for a MRSR mission to Mars there needs to be considerable analysis done on board the rover. Furthermore, the discrepancy between the amount of sample gathered and the amount to be returned suggests that there needs to be some method of choosing the optimal set of samples. This type of analysis will require pristine material-unaltered by the drilling process. Since the core drill thermally and mechanically alters the outer diameter (about 10 pct) of the core sample, this outer area cannot be used. The primary function of the core handling device is to extract subsamples from the core and to position these subsamples, and the core itself if needed, with respect to the various analytical instruments that can be used to perform these analyses.

Gwynne, Owen↗

Distillation of H2O from hard-frozen Martian permafrost

The authors present a method for distillation of hard-frozen Martian permafrost. A cable-tool is drilled into hard frozem permafrost to a depth of 10 to 20 m. They calculate that a 10 m hole could be drilled in a few days. A 10 m shaft with a diameter equal to the bore is inserted into the hole, and a air tight tent-like structure is erected over the borehole. Photovoltaic cells mounted on the tent supply electrical energy that is dissipated in the shaft. Drilling power can be supplied by other sources. With 1000 watts, the shaft can be heated to near 350 K, producing relatively high temperatures in the vicinity of the borehole. Surrounding H2O is vaporized and diffuses up through the regolith. The authors calculate that a tent of a radius of no more than a few meters would intercept most of the H2O as it diffused to the surface. Calculations suggest that it would require perhaps 30 days to extract H2O from most of the volume drained by this technique. Assuming that the hard frozen regolith is no more than 10 percent ice, the author's calculate that that about 2890 kg of H2O could be extracted in 30 days. Since the nominal requirement for each crew member is about 5 kg/day, one such borehole might be expected to supply enough H2O to maintain a crew of 5 for perhaps 100 days. Additional engineering studies will be done to attempt to improve the capacity or efficiency of this method.

Zent, A. P.↗