Search NASA⌕ Search

SEARCH · Search NASA

Results for “Defect modelling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60
All sourcesNASA NTRSDOE OSTI
NASA NTRS2009

Chromosomal Aberrations in DNA Repair Defective Cell Lines: Comparisons of Dose Rate and Radiation Quality

Chromosome aberration yields were assessed in DNA double-strand break repair (DSB) deficient cells after acute doses of gamma-rays or high-LET iron nuclei, or low dose-rate (0.018 Gy/hr) gamma-rays. We studied several cell lines including fibroblasts deficient in ATM (product of the gene that is mutated in ataxia telangiectasia patients) or NBS (product of the gene mutated in the Nijmegen breakage syndrome), and gliomablastoma cells that are proficient or lacking in DNA-dependent protein kinase, DNA-PK activity. Chromosomes were analyzed using the fluorescence in-situ hybridization (FISH) chromosome painting method in cells at the first division post-irradiation and chromosome aberrations were identified as either simple exchanges (translocations and dicentrics) or complex exchanges (involving >2 breaks in 2 or more chromosomes). Gamma radiation induced higher yields of both simple and complex exchanges in the DSB repair defective cells than in the normal cells. The quadratic dose-response terms for both chromosome exchange types were significantly higher for the ATM and NBS defective lines than for normal fibroblasts. However, the linear dose-response term was significantly higher only for simple exchanges in the NBS cells. Large increases in the quadratic dose response terms indicate the important roles of ATM and NBS in chromatin modifications that facilitate correct DSB repair and minimize aberration formation. Differences in the response of AT and NBS deficient cells at lower doses suggests important questions about the applicability of observations of radiation sensitivity at high dose to low dose exposures. For all iron nuclei irradiated cells, regression models preferred purely linear and quadratic dose responses for simple and complex exchanges, respectively. All the DNA repair defective cell lines had lower Relative biological effectiveness (RBE) values than normal cells, the lowest being for the DNA-PK-deficient cells, which was near unity. To further investigate the sensitivity differences for low and low high doses, we performed chronic low dose-rate irradiation, and have begun studies with ATM and Nibrin inhibitors and siRNA knockout of these proteins. Results support the conclusion that for the endpoint of simple chromosomal aberrations (translocation or dicentrics), the increased radiation sensitivity of AT cells found at high doses (>1 Gy) does not carry over to low doses or doserates, while NBS cells show increased sensitivity for both high and low dose exposures.

George, K. A.↗
DOE OSTI2024

As‐Doped Polycrystalline CdSeTe: Localized Defects, Carrier Mobility and Lifetimes, and Impact on High‐Efficiency Solar Cells

Abstract The efficiency potential for single‐junction photovoltaics (PV) is described by the detailed balance model, which requires the elimination of nonradiative recombination and perfect minority carrier collection. Improvements in GaAs, Si, and perovskite PV follow this model. It might be more complex for CdTe, a leading thin‐film PV technology. While lifetime, passivation, and doping goals for 25% efficient CdTe solar cells are largely reached, voltage is ≈20% below the detailed balance limit. Why is that? In Se‐alloyed CdSe x Te 1‐x (Se is required for >20% efficiency) additional losses can occur due to electrostatic and bandgap fluctuations and due to electronic trap states. To understand mechanisms limiting CdSeTe solar cell performance and to suggest improvements, carrier dynamics, and transport in CdSe x Te 1‐x with variation in Se composition and as doping is analyzed. It is shown that trapping, likely due to anion‐site defects and their complexes, is correlated with low charge carrier mobility of 0.1–0.6 cm 2 (Vs) −1 . Even with 1000 ns charge carrier lifetimes, carrier diffusion length is less than the absorber thickness, reducing efficiency to ≈23%. Device simulations are used to analyze the performance of CdSe x Te 1‐x solar cells; thermodynamic models are not sufficient for absorbers with electronic disorder and trapping.

14 SOLAR ENERGY↗
NASA NTRS2005

Structural Verification of the Redesigned Space Shuttle Bipod Foam Closeout

This document outlines the structural verification approach for the Space Shuttle External Tank Forward Bipod Foam Closeout. Due to the Space Shuttle Columbia accident, debris has become a major concern. The intent of the structural verification is to ensure that any debris shed from the bipod is within acceptable limits. Since cohesive failure due to internal defects was identified as the most likely cause of the STS-107 bipod ramp foam failure, verification for this failure mode receives particular emphasis. However, all failure modes for TPS are considered and appropriate verification rationale is developed for each failure mode. Figure 1 depicts the structural verification of a production design where analysis and test are the primary methods of verification. It can be seen that the successful completion of structural verification is dependent on three main areas: 1. Production process control and quality assurance must ensure that test articles and/or analytical models are representative of (or conservatively envelope) production hardware in terms of geometry, materials and processing. Variability and defects must be considered. 2. Flight environments must be sufficiently characterized to bound driving environments for all failure modes. Applied environments, either test or analytical, must be representative of flight environments and have a load factor that satisfies design requirements. 3. Structural verification must include all failure modes. A comprehensive list of failure modes and the underlying failure mechanisms has been generated based on flight and test experience. Verification tests and / or analyses must address each failure mode. ET TPS Verification is accomplished by a combination of analysis, test, and similarity.

Poole, Eric L.↗
DOE OSTI2025

Tiny Bubbles: Combined HR(S)TEM and 4D-STEM Analysis of Sub-Nanometer He Bubbles in Au

Irradiation produces a distribution of defect sizes in materials, with the smallest defects often below one nanometer in size and approaching the scale of a single unit cell in metals. While high-resolution scanning transmission electron microscopy (STEM)-based imaging can directly image structures at this level, techniques such as four-dimensional STEM (4D-STEM) enable characterization of materials across large fields of view, capturing a more representative volume that can be valuable for quantifying defects, their distributions, and the associated strain fields. Here we present a combined HRSTEM and 4D-STEM approach to study the model system of He bubble implantation in an Au thin film. The present work is of general interest for the study of materials in extreme environments, as it demonstrates an effective way to characterize even the tiniest sub-nanometer sized He bubbles in addition to larger irradiation defects.

atomic-resolution STEM↗
DOE OSTI2022

The role of deviatoric stress and dislocations on the α to ω phase transformation in Ti

Under extreme conditions, α-Ti becomes unstable and transforms either into β-Ti at high temperature or into ω-Ti at high pressure. In what concerns the α to ω phase transformation (PT), there has been a wide range of experimentally reported transition pressures from approximately 2 to 15 GPa at room temperature. Deviatoric stresses and internal defects are often assumed to be the root cause of this variation. Here, in this study, these postulates are revisited using both continuum mechanics and molecular dynamics (MD) simulations. First, a simple continuum model, assuming linear elasticity and isotropic plasticity, is developed to describe the effects of applied stress and dislocations on the stability of an ω nucleus in an infinite α domain. Second, a new MD simulation method is developed to generate an ω nucleus in the α domain utilizing the displacement field identified from the topological analysis. Results from MD simulations show that despite the fact that phase diagrams typically delineate the limits between two phases in terms of only P and T, deviatoric stress promotes the α to ω phase transformation by reducing the critical radius above which an ω nucleus is stable. Furthermore, the required deviatoric stress to nucleate and stabilize a nanoscale ω nucleus is likely emanating from the internal stress of defects such as dislocations. The MD-informed micromechanics models are used to identify favorable configurations where dislocations help favor the α to ω transformation. These configurations show that the interaction with a basal or prismatic dislocation reduces the critical radius of a ω nucleus by about 10 or 16 %, respectively. In addition, prismatic edge dislocations are found to promote the growth of ω nucleus when interacting with the ($\bar{1}$$\bar{1}$20) α //(0001) ω interface. Importantly, a simple model of the arrival of dislocation at an ω nucleus suggests that PT does not necessarily require a pile-up to be present but could alternatively be mediated by a constant rapid flow of dislocations.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Anisotropic shock response of single-crystalline β-phase tin shock physics, molecular dynamics, plasticity

Mesoscale simulations of the dynamic response of polycrystalline metals to shockwave compression can provide unique insight in to the nature of the various physical mechanisms responsible for material failure. This approach requires a constitutive description for individual grains and boundaries, including defects such as dislocations, within an explicit representation of the microstructure geometry and evolving deformation fields. Computational models of the single-crystal constituents cannot be unambiguously constrained by traditional measurements of the shock or stress-strain response of polycrystalline metals. Instead, these models require comprehensive measurements of the anisotropic shock response of single crystals for their calibration and validation. We present a coordinated experimental and simulation campaign on the shock response of single-crystalline β-phase tin demonstrating a remarkable anisotropic elastic-plastic response of the metal. This anisotropy will be explained with the help of molecular dynamics simulations that show preferred twinning in one orientation.

36 MATERIALS SCIENCE↗
NASA NTRS1992

Calculation of fully three-dimensional separated flow with an unsteady viscous-inviscid interaction method

Three previous papers have shown that the viscous inviscid numerical methods were capable of calculating separated turbulent flows. The 'Semi-inverse method' and the models of the first author allow the computation of massive separations, stalled flows, and shock wave-boundary layer interactions, in two-dimensional or quasi-three-dimensional conditions, from low speeds to supersonic speeds. The 'Semi-implicit' method for time-consistent coupling allows for the computation of time-accurate transonic separated flow and buffer computations in two-dimensions. The present paper shows that the viscous-inviscid interaction approach is also able to compute the fully three-dimensional flow separation phenomena. The method is based on a thin-layer approximation of the theory of 'Defect-Formulation' that provides the viscous-inviscid splitting of the Navier-Stokes equations. A parametric analytical modelling of the 3D-turbulent velocity profiles is involved. Numerically, the 3D-velocity profiles are discretized in the normal z-direction and driven by parametric integral 3D-equations in direct or inverse modes in the x-direction. The viscous-inviscid coupling is fully 3D and solved the time-consistency problem with an extension of the 'Semi-implicit' method previously suggested in two-dimensions. A 3D inviscid subroutine with TSP approximation is used. Results are obtained for transonic steady flows over wings with shock-induced transonic separation. The method provides results for highly three-dimensional flow separations, such as induced by a three-dimensional through at the wall of a flat plate. The 3D viscous-inviscid coupling and the 3D model of the velocity field provide three-dimensional instantaneous skin-friction lines whose patterns exhibit the same complex topology as Navier-Stokes solvers, with foci, nodes, and saddle-points.

Leballeur, J. C.↗
DOE OSTI2023

Towards deep computer vision for in-line defect detection in polymer electrolyte membrane fuel cell materials

Polymer Electrolyte Membrane (PEM) fuel cells are a promising source of alternative energy. However, their production is limited by a lack of well-established methods for quality control of their constituent materials like the membrane-electrode assembly during roll-to-roll manufacturing. One potential solution is the implementation of deep learning methods to detect unwanted defects through their detection in scanned images. Here we explore the detection of defects like scratches, pinholes, and scuffs in a sample dataset of PEM optical images using two deep learning algorithms: Patch Distribution Modeling (PaDiM) for unsupervised anomaly detection and Faster-RCNN for supervised object detection. Both methods achieve scores on performance metrics (ROC-AUC and PRO-AUC for PaDiM and AP for Faster-RCNN) that are comparable to their scores on benchmark datasets. These methods also have the potential to detect a wider range of defects compared to IR thermography and previous optical inspection methods. Overall, deep learning shows promise at detecting relevant defects of interest and has the potential to achieve real-time defect detection.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2022

Temporal and spatial laser intensification within nodular defects overcoated with multilayer dielectric mirrors over a wide range of defect geometries

The nodular defect shape and the laser incidence angle have a dramatic impact on the spatial distribution of light intensification within the nodule as well as how the laser light is drained from the defect. Nodular defect geometries unique to ion beam sputtering, ion-assisted deposition, and electron-beam (e-beam) deposition, respectively, are modeled in this parametric study over a wide range of nodular inclusion diameters and layer count for optical interference mirror coatings constructed with quarter-wave thicknesses and capped with a half wave of the low index material. It was found for hafnia ($n$=1.9) and silica ($n$=1.45) multilayer mirrors that the light intensification in nodular defects with a $C$ factor of 8, typical of e-beam deposited coatings deposited with a wide range of deposition angles, was maximized for a 24-layer design. For intermediate size inclusion diameters, increasing the layer count for normal incidence multilayer mirrors reduced the light intensification within the nodular defect. A second parametric study explored the impact of the nodule shape on the light intensification for a fixed number of layers. In this case, there is a strong temporal trend for the different nodule shapes. Narrow nodules tend to drain more laser energy through the bottom of the nodule into the substrate while wide nodules tend to drain more laser energy through the top of the nodule when irradiated at normal incidence. Further, at a 45° incidence angle, waveguiding is an additional method to drain laser energy from the nodular defect. Finally, laser light resonates within nodular defects longer than within the adjacent nondefective multilayer structure.

47 OTHER INSTRUMENTATION↗
NASA NTRS1980

Modeling of radiation damage in silicon solar cells

One MeV electron irradiation produces preponderantly isolated vacancy interstitial pairs. If neither of these defects is mobile, the concentration of each grows linearly with fluence. Annealing of damage depends on the nature of the damage. Vacancy interstitial pairs which are bound by an interaction such that they mutually annihilate rather than dissociate are termed close pairs; close pair recovery usually occurs at a lower temperature than the temperature at which long distance defect migration occurs. Annealing of the remaining frozen in damage occurs when a temperature is reached where the vacancy or interstitial is mobile; usually the interstitial is more mobile than the vacancy. The recovery occurs in two regimes which may be resoluable.

Oehrlein, G.↗
DOE OSTI2021

Development of NDE/NDT Tools for High-Volume & High-Speed Inspection of CFRP Structures in Automotive Manufacturing

Main advantages of the air-coupled ultrasound testing (ACUT) and electromagnetic testing (EMT) techniques for NDE of CFRP composites were non-contact sensing, scalability for high-speed inspection, cost-effectiveness, and non-hazardous operation. Despite these advantages, no systems that would satisfy the project requirements were commercially available. Hence, one of the major efforts of the Michigan State University (MSU) team at the initial stage of the project was to close this technological gap by developing, optimizing, and validating array sensors that would provide sufficient sensitivity, spatial coverage, and resolution for robust defect detection. Optimization of the ACUT and EMT sensor designs was performed using experimentally validated finite element models. Initial experiments using array probes were conducted on relatively flat CFRP samples. In parallel, the MSU team designed and assembled a portable platform with two robotic arms. The robots were equipped with newly designed sensors that enabled high-speed NDE of curved CFRP parts. Presently, the developed robotic platform can be used as a demo/template NDE system, which is easily adaptable to manufacturing environments and in-line NDE. The ACUT NDE system developed by the MSU team used a high-power 4-channel pulser receiver for parallel data acquisition. The array probes were designed by stacking commercially available ACUT transducers, which operated in the frequency range between 100 kHz and 500 kHz. MSU optimized the excitation procedure and developed wave focusing cones so as to reduce the crosstalk between the transducers and to provide higher pulse repletion frequency (PRF). The through-transmission (TT) and single-side access (SSA) inspection modes were successfully implemented. In the TT-ACUT, structural defects in CFRP were detected by passing ultrasonic waves through the test part. Hence, the ACUT transmitters and receivers needed to be placed on the opposite sides of the test part. In the SSA-ACUT, guided waves (GW) were excited in the test part using the transmitters and were sensed by the receivers from the same side. Multi-channel TT-ACUT and SSA-ACUT provided high-speed NDE, and were successfully validated on CFRP test samples with interlaminar delaminations and other embedded defects The EM techniques developed by the MSU team included: 1) eddy current testing (ECT), 2) capacitive imaging (CI) and hybrid dual-mode imaging. In ECT, structural damage was detected in CFRP using coils sensor arrays. In ECT, the excitation magnetic field is generated by passing an alternating current through a coil, which is placed above the test sample. The excitation field penetrates the conductive sample and induces the eddy currents in its transect. In turn, the eddy currents generate the reaction field, which affects the total field sensed by a coil. Hence, the presence of structural flaws will alter the eddy current flow and the picked-up signal. ECT is mostly sensitive to local changes of the electric conductivity of the test sample, and CFRPs are mostly conductive in the direction of carbon fibers. Hence, ECT was well suited for the detection of fiber damage/fiber irregularities. The MSU team developed printed circuit boards (PCB) with coil sensor arrays optimized for NDE of CFRP. Unlike most commercial probes designed for ECT of metallic structures, the MSU array probes were designed for operation in [1-10] MHz frequency range, which was optimal for low-conductive CFRP. Multiple sensing topologies (coil groups excitation/sensing arrangements) were implemented and successfully validated. Capacitive Imaging (CI) technique developed by MSU was complementary to ECT. In contrast to ECT, which was sensitive to local changes of the electrical conductivity, the CI was sensitive to local changes of the dielectric constant. Therefore, CI could provide information about matrix damage/matrix irregularities in CFRP. The MSU CI sensor arrays were made of multiple circular or rectangular open-plate capacitors printed on PCB. Sensors of this type are not commercially available. In addition to ECT and CI, the MSU team developed a hybrid (dual-mode) inductive/capacitive measurement technique that synergistically combined the benefits of inductive and capacitive sensing for rapid NDE of fiber reinforced polymer (FRP) composite structures. Fiber damage and fiber irregularities in FRPs were detected by configuring hybrid sensors as coil sensors. Similarly, matrix damage, matrix irregularities and interlaminar delaminations were detected by configuring hybrid sensors as capacitive sensors. ECT and CI were performed sequentially by means of electronic switching. Hence, eliminating the need for mounting two separate sensor arrays on the probe. Portable robotic platform was developed by MSU for multi-technique high-speed NDE of CFRP test parts. The platform had two 6-axis robots, which enabled inspection of curved parts in approximately a 6×6×6 ft 3 active scan area. On the software side, the MSU team integrated scripts for NDE hardware control with scripts for robot motion control. MSU also implemented automated path planning for the robots, reconstruction of part’s surfaces via stereovision, 3D rendering of inspection data, and image processing algorithms for enhanced defect detection. Automotive composite parts manufactured by Plasan Composites from Phase I were used to validate the ACUT and EMT techniques on representative testbeds. Among those parts were three X-braces for a Dodge Viper, one composite calibration plaque with known defects at known locations, and four other test sections, including sections from a front splitter, a corner section from a composite hood, and a high-pressure RTM panel made using non crimp fabric. Other test samples included CFRP and GFRP calibration plates with fiber/matrix defects fabricated at MSU/CVRC.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Engineering quantum-coherent defects: The role of substrate miscut in chemical vapor deposition diamond growth

The engineering of defects in diamond, particularly nitrogen-vacancy (NV) centers, is important for many applications in quantum science. A materials science approach based on chemical vapor deposition (CVD) growth of diamond and in situ nitrogen doping is a promising path toward tuning and optimizing the desired properties of the embedded defects. Herein, with the coherence of the embedded defects in mind, we explore the effects of substrate miscut on the diamond growth rate, nitrogen density, and hillock defect density, and we report an optimal angle range for the purposes of engineering coherent ensembles of NV centers in diamond according to our growth parameters. We provide a model that quantitatively describes hillock nucleation in the step-flow regime of CVD growth, shedding insight on the physics of hillock formation. We also report significantly enhanced incorporation of nitrogen at hillock defects, opening the possibility for templating hillock-defect-localized NV center ensembles for quantum applications.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2023

Hydrogen-induced degradation dynamics in silicon heterojunction solar cells via machine learning

Abstract Among silicon-based solar cells, heterojunction cells hold the world efficiency record. However, their market acceptance is hindered by an initial 0.5% per year degradation of their open circuit voltage which doubles the overall cell degradation rate. Here, we study the performance degradation of crystalline-Si/amorphous-Si:H heterojunction stacks. First, we experimentally measure the interface defect density over a year, the primary driver of the degradation. Second, we develop SolDeg, a multiscale, hierarchical simulator to analyze this degradation by combining Machine Learning, Molecular Dynamics, Density Functional Theory, and Nudged Elastic Band methods with analytical modeling. We discover that the chemical potential for mobile hydrogen develops a gradient, forcing the hydrogen to drift from the interface, leaving behind recombination-active defects. We find quantitative correspondence between the calculated and experimentally determined defect generation dynamics. Finally, we propose a reversed Si-density gradient architecture for the amorphous-Si:H layer that promises to reduce the initial open circuit voltage degradation from 0.5% per year to 0.1% per year.

14 SOLAR ENERGY↗
DOE OSTI2021

A Rate Theory Model of Radiation-Induced Swelling in an Austenitic Stainless Steel

Many rate theory models of cavity (void) swelling have been published over the past 50 years, all having the same, or similar, structures. A rigorous validation of the models has not been possible because of the dearth of information concerning the microstructures that correspond with the swelling data. Whereas the lack of microstructure information is still an issue for historical swelling data, in the past 10–20 years data have been published on the evolution of the microstructure (point defect yields from collision cascades, cavity number densities, and dislocation densities/yield strengths) allowing certain gaps in information to be filled when considering historic swelling data. With reasonable estimates of key microstructure parameters, a standard rate theory model can be applied, and the model parameter space explored, in connection with historical swelling data. By using published data on: (i) yield strength as a function of dose and temperature (to establish an empirical expression for dislocation density evolution); (ii) cavity number densities as a function of temperature; and (iii) freely migrating defect (FMD) production as a function of primary knock-on atom (PKA) spectrum, the necessary parameter and microstructure inputs that were previously unknown can be used in model development. This paper describes a rate-theory model for void swelling of 316 stainless steel irradiated in the EBR-2 reactor as a function of irradiation temperature and neutron dose.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Mixture-of-Experts for Multi-Domain Defect Identification in Non-Destructive Inspection

Composite materials are widely used in aircraft structures because of their superior mechanical properties. However, their complex failure modes require sophisticated inspection methods to ensure structural integrity. Ultrasonic testing (UT) is a common non-destructive inspection (NDI) technique for aircraft composites that can detect internal and external defects with high resolution and accuracy. Despite their effectiveness, traditional UT methods rely on the manual interpretation of ultrasonic signals, which is time-consuming, labor-intensive, and subjective. Furthermore, processing such large-scale data, particularly across materials of varying thicknesses, significantly increases the computational demands of deep learning model optimization. To overcome these challenges, we propose an efficient sparse mixture-of-experts (MoE) model with a multi-level loss function and introduce four novel training objectives to improve computational efficiency and accuracy in identifying surface defects in composite aircraft materials. Here, we evaluated our approach on material with multiple thicknesses or domains comprising various defects. Our experimental results demonstrate higher accuracy and F1-Score, with only 10% training epochs compared to baseline MoE.

composite materials↗
DOE OSTI2023

Probing supersymmetric black holes with surface defects

It has long been conjectured that the large N deconfinement phase transition of $\mathcal{N}$ = 4 SU(N) super-Yang-Mills corresponds via AdS/CFT to the Hawking-Page transition in which black holes dominate the thermal ensemble, and quantitative evidence of this has come through the recent matching of the superconformal index of $\frac{1}{16}$-BPS states to the supersymmetric black hole entropy. Here we introduce the half-BPS Gukov-Witten surface defect as a probe of the superconformal index, which also serves as an order parameter for the deconfinement transition. This can be studied directly in field theory as a modification of the usual unitary matrix model or in the dual description as a D3-brane probe in the background of a (complex) supersymmetric black hole. Using a saddle point approximation, we determine our defect index in the large N limit as a simple function of the chemical potentials and show independently that it is reproduced by the renormalized action of the brane in the black hole background. Along the way, we also comment on the Cardy limit and the thermodynamics of the D3-brane in the generalized ensemble. The defect index sharply distinguishes between the confining and the deconfining phases of the gauge theory and thus is a supersymmetric non-perturbative order parameter for these large N phase transitions which deserves further investigation. Finally, our work provides an example where the properties of a black hole coupled to an external system can be analyzed precisely.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
NASA NTRS2005

Mouse infection models for space flight immunology

Several immunological processes can be affected by space flight. However, there is little evidence to suggest that flight-induced immunological deficits lead to illness. Therefore, one of our goals has been to define models to examine host resistance during space flight. Our working hypothesis is that space flight crews will come from a heterogeneous population; the immune response gene make-up will be quite varied. It is unknown how much the immune response gene variation contributes to the potential threat from infectious organisms, allergic responses or other long term health problems (e.g. cancer). This article details recent efforts of the Kansas State University gravitational immunology group to assess how population heterogeneity impacts host health, either in laboratory experimental situations and/or using the skeletal unloading model of space-flight stress. This paper details our use of several mouse strains with several different genotypes. In particular, mice with varying MHCII allotypes and mice on the C57BL background with different genetic defects have been particularly useful tools with which to study infections by Staphylococcus aureus, Salmonella typhimurium, Pasteurella pneumotropica and Ehrlichia chaffeensis. We propose that some of these experimental challenge models will be useful to assess the effects of space flight on host resistance to infection.

Review↗
NASA NTRS2003

Phase Sensitive X-Ray Diffraction Imaging Study of Protein Crystals

The study of defects and growth of protein crystals is of importance in providing a fundamental understanding of this important category of systems and the rationale for crystallization of better ordered crystals for structural determination and drug design. Yet, as a result of the extremely weak scattering power of x-rays in protein and other biological macromolecular crystals, the extinction lengths for those crystals are extremely large and, roughly speaking, of the order of millimeters on average compared to the scale of micrometers for most small molecular crystals. This has significant implication for x-ray diffraction and imaging study of protein crystals, and presents an interesting challenge to currently available x-ray analytical techniques. We proposed that coherence-based phase sensitive x-ray diffraction imaging could provide a way to augment defect contrast in x-ray diffraction images of weakly diffracting biological macromolecular crystals. I shall examine the principles and ideas behind this approach and compare it to other available x-ray topography and diffraction methods. I shall then present some recent experimental results in two model protein systems-cubic apofemtin and tetragonal lysozyme crystals to demonstrate the capability of the coherence-based imaging method in mapping point defects, dislocations, and the degree of perfection of biological macromolecular crystals with extreme sensitivity. While further work is under way, it is intended to show that the observed new features have yielded important information on protein crystal perfection and nucleation and growth mechanism otherwise unobtainable.

Hu, Z. W.↗