Search NASA⌕ Search

SEARCH · Search NASA

Results for “Dynamic parameter”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60

Study of CO2 laser smoothing of surface roughness in fused silica

Small micrometer-sized roughness on optical surfaces, caused by laser damage and/or redeposition of laser ablated material, can cause local electric field intensification which may lead to damage initiation both on the optics and/or downstream. We examined the smoothing of etched periodic surface structures on SiO{sub 2} substrate with 10.6 {micro}m CO{sub 2} laser using atomic force microscopy. The characteristic surface tension driven mass flow of the glass under different laser parameters were simulated using computational fluid dynamics and correlated with experimental results. We found that during CO{sub 2} laser polishing the estimate viscosity of the silica glass appears to be higher than typical literature values measured at a temperature similar to the laser heating conditions. This discrepancy can be explained by the observation that at high temperature, a significant portion of the hydroxyl content in the layer of heated silica glass can diffuse out resulting in a much stiffer glass.

42 ENGINEERING↗

Exploring the effect of fluid dynamics and kinetic mechanisms on n-heptane autoignition in transient jets

The influence of physical parameters and of flow patterns on the prediction of n-heptane ignition dynamic in transient reacting n-heptane jets, in high pressure environment under laminar conditions, has been explored by using different kinetic mechanisms. Some preliminary transient laminar flamelet computations have been performed, thus showing that the sensitivity of the ignition time to strain rate depends on the kinetic mechanism used. Therefore, the structure of the reacting jet, in particular the localization of ignition spots, is investigated. The results show that, if the initial temperature of the reacting mixture is out of the intermediate range (800-1000 K) towards lower values, the fluid dynamics has an essential role. In this case, the ignition delay time is almost insensitive to the specific kinetic mechanism adopted, conversely it is severely shortened by increasing the streamwise velocity. The burning spot is located in the core of fuel roll-up, where low values of scalar dissipation rate occur. Nevertheless, the most reactive mixture fraction conditions are well predicted by chemical kinetics, as they are in good agreement with those computed for the one-dimensional diffusion layer. When the initial temperature of fuel and air is increased in the intermediate range, ignition is strongly dependent on the kinetic mechanism used. In these cases, the choice of an accurate chemical scheme is fundamental in order to obtain reliable results. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Noise elimination algorithm for modal analysis

Modal analysis is an ongoing interdisciplinary physical issue. Modal parameters estimation is applied to determine the dynamic characteristics of structures under vibration excitation. Modal analysis is more challenging for the measured vibration response signals are contaminated with noise. This study develops a mathematical algorithm of structured low rank approximation combined with the complex exponential method to estimate the modal parameters. Physical experiments using a steel cantilever beam with ten accelerometers mounted, excited by an impulse load, demonstrate that this method can significantly eliminate noise from measured signals and accurately identify the modal frequencies and damping ratios. This study provides a fundamental mechanism of noise elimination using structured low rank approximation in physical fields.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Dynamic Tuning of Seismic Signal Detector Trigger Levels for Local Networks

The quality of automatic signal detections from sensor networks depends on individual detector trigger levels (TLs) from each sensor. The largely manual process of identifying effective TLs is painstaking and does not guarantee optimal configuration settings, yet achieving superior automatic detection of signals and ultimately, events, is closely related to these parameters. In this paper, we present a Dynamic Detector Tuning (DDT) system that automatically adjusts effective TL settings for signal detectors to the current state of the environment by leveraging cooperation within a local neighborhood of network sensors. After a stabilization period, the DDT algorithm can adapt in near-real time to changing conditions and automatically tune a signal detector to identify (detect) signals from only events of interest. Our current work focuses on reducing false signal detections early in the seismic signal processing pipeline, which leads to fewer false events and has a significant impact on reducing analyst time and effort. This system provides an important new method to automatically tune detector TLs for a network of sensors and is applicable to both existing sensor performance boosting and new sensor deployment. Finally, with ground truth on detections from a local neighborhood of seismic sensors within a network monitoring the Mount Erebus volcano in Antarctica, we show that DDT reduces the number of false detections by 18% and the number of missed detections by 11% when compared with optimal fixed TLs for all sensors.

58 GEOSCIENCES↗

Relativistic Modeling of Ultra-Short Electron Pulse Propagation

The ultrafast electron microscopy, electron diffraction, electron crystallography, and nanocrystallography methods opened the possibility of studying the coherent structural dynamics of matter. The time resolution of the ultrafast electron microscopy and electron diffraction methods determined by the duration of electron pulses is the key parameter of experimental setups. This paper treats electron pulse dynamics in the field free drift region specifically for applications in atomic imaging. The electron beam is modeled as a system of particles (N) with N = 1000 and N = 10 000 electrons. The beam propagates for a certain period of time (1–4 ns); during its propagation, electron distribution parameters (over coordinates and velocities) are calculated to characterize the temporal profile and uncertainty in the electron wavelength at the sample. The results of applying relativistic dynamic equations show that nonrelativistic results are satisfactorily applicable (with 15 per cent or better accuracy) for modeling short electron pulse elongation and broadening at 30 keV and lower energies. However, the results of such modeling may be significantly in error for intermediate energies (300 keV), and for the fast relativistic beams (3 MeV) they become completely wrong. The relative reduction in Coulomb repulsion effects at higher energies is known, however; we give a comprehensive treatment that allows a quantitative picture. Using high-energy electron pulses results in almost complete elimination of the repulsive Coulomb effect. Dispersion of electron velocities becomes much lower at higher energies. For 3 MeV electrons, electron pulse duration as well as its radius does not noticeably change even after traveling for 4 ns (1.2 m). Even at 300 keV, the pulse duration increase is negligible until 1 ns (0.2 m). A simple mean-field model suggested in [13] has been extended to arbitrarily fast relativistic electron pulses with good correspondence to direct dynamic modeling.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Mathematical Foundations for Uncertainty Quantification in Materials Design. Final Report

Final report DE-SC0010723. Our key accomplishment in the first year of the grant is that we started developing pathwise information theory-based and goal-oriented sensitivity analysis and parameter identification methods for complex high-dimensional dynamics and in particular of nonequilibrium extended systems. The combination of these novel methodologies provide the first methods in the literature which are capable to handle UQ questions for stochastic complex systems with some or all of the following features: (a) multi-scale models with a very large number of parameters, (b) spatially distributed systems such as Kinetic Monte Carlo or Langevin Dynamics, (c) non-equilibrium processes typically associated with coupled physico-chemical mechanisms, driven boundary conditions, etc. The first two such publications sponsored by the grant, have just been published.

36 MATERIALS SCIENCE↗

Coupled land surface–subsurface hydrogeophysical inverse modeling to estimate soil organic carbon content and explore associated hydrological and thermal dynamics in the Arctic tundra

Quantitative characterization of soil organic carbon (OC) content is essential due to its significant impacts on surface–subsurface hydrological–thermal processes and microbial decomposition of OC, which both in turn are important for predicting carbon–climate feedbacks. While such quantification is particularly important in the vulnerable organic-rich Arctic region, it is challenging to achieve due to the general limitations of conventional core sampling and analysis methods, and to the extremely dynamic nature of hydrological–thermal processes associated with annual freeze–thaw events. In this study, we develop and test an inversion scheme that can flexibly use single or multiple datasets – including soil liquid water content, temperature and electrical resistivity tomography (ERT) data – to estimate the vertical distribution of OC content. Our approach relies on the fact that OC content strongly influences soil hydrological–thermal parameters and, therefore, indirectly controls the spatiotemporal dynamics of soil liquid water content, temperature and their correlated electrical resistivity. We employ the Community Land Model to simulate nonisothermal surface–subsurface hydrological dynamics from the bedrock to the top of canopy, with consideration of land surface processes (e.g., solar radiation balance, evapotranspiration, snow accumulation and melting) and ice–liquid water phase transitions. For inversion, we combine a deterministic and an adaptive Markov chain Monte Carlo (MCMC) optimization algorithm to estimate a posteriori distributions of desired model parameters. For hydrological–thermal-to-geophysical variable transformation, the simulated subsurface temperature, liquid water content and ice content are explicitly linked to soil electrical resistivity via petrophysical and geophysical models. We validate the developed scheme using different numerical experiments and evaluate the influence of measurement errors and benefit of joint inversion on the estimation of OC and other parameters. We also quantify the propagation of uncertainty from the estimated parameters to prediction of hydrological–thermal responses. We find that, compared to inversion of single dataset (temperature, liquid water content or apparent resistivity), joint inversion of these datasets significantly reduces parameter uncertainty. We find that the joint inversion approach is able to estimate OC and sand content within the shallow active layer (top 0.3 m of soil) with high reliability. Due to the small variations of temperature and moisture within the shallow permafrost (here at about 0.6 m depth), the approach is unable to estimate OC with confidence. However, if the soil porosity is functionally related to the OC and mineral content, which is often observed in organic-rich Arctic soil, the uncertainty of OC estimate at this depth remarkably decreases. Our study documents the value of the new surface–subsurface, deterministic–stochastic inversion approach, as well as the benefit of including multiple types of data to estimate OC and associated hydrological–thermal dynamics.

58 GEOSCIENCES↗

Dynamic modeling of a single-stage downward firing, entrained flow gasifier

The gasifier is the heart of the integrated gasification combined cycle (IGCC), a technology that has emerged as an attractive alternative to conventional coal-fired power plant technology due to its higher efficiency and cleaner environmental performance especially with the option of CO{sub 2} capture and sequestration. Understanding the optimal performance of the gasifier is therefore paramount for the efficient operation of IGCC power plants. Numerous gasifier models of varying complexity have been developed to study the various aspects of gasifier performance. These range from simple one-dimensional (1D) process-type models to rigorous higher order 2-3D models based on computational fluid dynamics (CFD). Whereas high-fidelity CFD models can accurately predict most key aspects of gasifier performance, they are computationally expensive and typically take hours to days to execute on high-performance computers. Therefore, faster 1D partial differential equation (PDE)-based models are required for use in dynamic simulation studies, control system analysis, and training applications. A number of 1D gasifier models can be found in the literature, but most are steady-state models that have limited application in the practical operation of the gasifier. As a result, 1D PDE-based dynamic models are needed to further study and predict gasifier performance under a wide variety of process conditions and disturbances. In the current study, a 1D transient model of a single-stage downward-fired GE/Texaco-type entrained-flow gasifier has been developed. The model comprises mass, momentum and energy balances for the gas and solid phases. The model considers the initial gasification processes of water evaporation and coal devolatilization. In addition, the key heterogeneous and homogeneous chemical reactions have been modeled. The resulting time-dependent PDE model is solved using the well-known method of lines approach in Aspen Custom Modeler®, whereby the PDEs in the spatial domain are discretized and the resulting differential algebraic equations (DAEs) are then integrated over time using a dynamic integrator. The dynamic response results of the gasifier performance parameters to certain disturbances commonly encountered during practical operation are presented. These disturbances include ramp and step changes to input variables such as coal flow rate, oxygen-to-coal ratio and water-to-coal ratio among others. Comparison of model predictions to available dynamic data will also be discussed.

01 COAL, LIGNITE, AND PEAT↗

Effects of collision cascade density on radiation defect dynamics in 3C-SiC

Effects of the collision cascade density on radiation damage in SiC remain poorly understood. We study damage buildup and defect interaction dynamics in 3C-SiC bombarded at 100 °C with either continuous or pulsed beams of 500 keV Ne, Ar, Kr, or Xe ions. Here, we find that bombardment with heavier ions, which create denser collision cascades, results in a decrease in the dynamic annealing efficiency and an increase in both the amorphization cross-section constant and the time constant of dynamic annealing. The cascade density behavior of these parameters is non-linear and appears to be uncorrelated. Our results demonstrate clearly (and quantitatively) an important role of the collision cascade density in dynamic radiation defect processes in 3C-SiC.

36 MATERIALS SCIENCE↗

Posterior predictive modeling using multi-scale stochastic inverse parameter estimates.

Multi-scale binary permeability field estimation from static and dynamic data is completed using Markov Chain Monte Carlo (MCMC) sampling. The binary permeability field is defined as high permeability inclusions within a lower permeability matrix. Static data are obtained as measurements of permeability with support consistent to the coarse scale discretization. Dynamic data are advective travel times along streamlines calculated through a fine-scale field and averaged for each observation point at the coarse scale. Parameters estimated at the coarse scale (30 x 20 grid) are the spatially varying proportion of the high permeability phase and the inclusion length and aspect ratio of the high permeability inclusions. From the non-parametric, posterior distributions estimated for these parameters, a recently developed sub-grid algorithm is employed to create an ensemble of realizations representing the fine-scale (3000 x 2000), binary permeability field. Each fine-scale ensemble member is instantiated by convolution of an uncorrelated multiGaussian random field with a Gaussian kernel defined by the estimated inclusion length and aspect ratio. Since the multiGaussian random field is itself a realization of a stochastic process, the procedure for generating fine-scale binary permeability field realizations is also stochastic. Two different methods are hypothesized to perform posterior predictive tests. Different mechanisms for combining multi Gaussian random fields with kernels defined from the MCMC sampling are examined. Posterior predictive accuracy of the estimated parameters is assessed against a simulated ground truth for predictions at both the coarse scale (effective permeabilities) and at the fine scale (advective travel time distributions). The two techniques for conducting posterior predictive tests are compared by their ability to recover the static and dynamic data. The skill of the inference and the method for generating fine-scale binary permeability fields are evaluated through flow calculations on the resulting fields using fine-scale realizations and comparing them against results obtained with the ground truth fine-scale and coarse-scale permeability fields.

58 GEOSCIENCES↗

Bethe ansatz approach to quench dynamics in the Richardson model

By instantaneously changing a global parameter in an extended quantum system, an initially equilibrated state will afterwards undergo a complex nonequilibrium unitary evolution whose description is extremely challenging. A nonperturbative method giving a controlled error in the long time limit remained highly desirable to understand general features of the quench induced quantum dynamics. In this paper we show how integrability (via the algebraic Bethe ansatz) gives one numerical access, in a nearly exact manner, to the dynamics resulting from a global interaction quench of an ensemble of fermions with pairing interactions (Richardson's model). This possibility is deeply linked to the specific structure of this particular integrable model which gives simple expressions for the scalar product of eigenstates of two different Hamiltonians. We show how, despite the fact that a sudden quench can create excitations at any frequency, a drastic truncation of the Hilbert space can be carried out therefore allowing access to large systems. The small truncation error which results does not change with time and consequently the method grants access to a controlled description of the long time behavior which is a hard to reach limit with other numerical approaches.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

An Experimental and Computational Study of a Single Diesel Droplet Impinging on a Dry Surface

This work presents experiments and computational simulations of a single diesel droplet impinging on a dry surface to provide a better understanding of the dynamics of the impingement process. The experimental work was carried out at several substrate surface temperatures where a single diesel droplet was dropped from a precision syringe pump to provide a specific droplet diameter and impact velocity. The effect of the surface temperature on the temporal evolution of the droplet spreading factor, dynamic contact angle, and contact line velocity was studied. The experimental study on the temporal evolution of the droplet-wall interaction was used to develop a dynamic contact angle model for computational simulations. Using an in-house multiphase flow solver, simulations of the single diesel droplet impingement were performed. The simulation results of the spreading factor were compared to the experimental results and the effects of liquid temperature and contact angle model parameters were investigated. The development of a dynamic contact angle model for diesel droplets enhances the ability to study diesel droplet impingement, an important factor in diesel fuel injection. With an accurate dynamic contact angle model, future studies can be performed at scales and velocities representative of the conditions present in internal combustion engines.

Markt, D.↗

WE-AB-303-07: Computational Monitoring Framework of Four-Dimensional Dose Distributions During Treatment Time Based On a 2D/3D Registration with Adaptive Transformation Parameters in Lung Stereotactic Body Radiotherapy

Purpose: The aim of this study was to develop a computational framework for monitoring four-dimensional (4D) dose distributions during treatment time based on a 2D/3D registration with adaptive transformation parameters (ATPs) in lung stereotactic body radiotherapy (SBRT). Methods: The 4D dose distributions during the SBRT were calculated by applying a pencil beam convolution (PBC) algorithm to simulated 4D-computed tomography (CT) images during treatment time (hereinafter referred to as “treatment” 4D-CT images). The “treatment” 4D-CT images were derived by deforming 3D planning CT images by using transformation parameters so that 2D planning portal dose images (PDIs) can resemble 2D dynamic clinical PDIs in each frame, which were derived from electronic portal imaging device (EPID) images. The transformation parameters were optimized by the Levenberg- Marquardt (LM) algorithm. The optimized transformation parameters in a certain frame were adaptively employed as initial transformation parameters for optimization of the parameters in the consecutive frame. Gamma pass rates (3mm/3%) between dynamic clinical PDIs and dynamic “treatment” PDIs derived from the “treatment” 4D-CT images were measured for comparing the proposed frameworks without and with the ATPs. These proposed frameworks were applied to the EPID dynamic images (40 frames) of two patients with lung cancer, who underwent the SBRT. Results: Gamma pass rates without and with the ATPs were 83.01±4.42% and 89.31±3.18% on average, respectively (p<0.05). Moreover, percentage errors between prescribed doses and estimated doses at an isocenter by the proposed frameworks without and with the ATPs were 10.67±5.66% and 6.34±0.47% on average, respectively (p<0.05). Conclusion: The proposed framework with ATPs could be useful to ensure the quality of the SBRT by monitoring 4D dose distributions during treatment time.

60 APPLIED LIFE SCIENCES↗

Stability analysis and observational constraints in scalar tensor theory

We study FRW cosmology for scalar tensor theory where two scalar functions nonminimally coupled to the geometry and matter lagrangian. In a framework to investigate stability and attractor solutions of the model in the phase space, we simultaneously solve the dynamical system and best fit the stability and model parameters with the observational data. The approach imposes restrictions on the model constraints while providing information about the universe dynamics. The model predict current accelerating universe, with a phantom crossing in near future.

79 ASTRONOMY AND ASTROPHYSICS↗

Inter-comparison of dynamic models for radionuclide transfer to marine biota in a Fukushima accident scenario

We report an inter-comparison of eight models designed to predict the radiological exposure of radionuclides in marine biota. The models were required to simulate dynamically the uptake and turnover of radionuclides by marine organisms. Model predictions of radionuclide uptake and turnover using kinetic calculations based on biological half-life (TB1/2) and/or more complex metabolic modelling approaches were used to predict activity concentrations and, consequently, dose rates of 90Sr, 131I and 137Cs to fish, crustaceans, macroalgae and molluscs under circumstances where the water concentrations are changing with time. For comparison, the ERICA Tool, a model commonly used in environmental assessment, and which uses equilibrium concentration ratios, was also used. As input to the models we used hydrodynamic forecasts of water and sediment activity concentrations using a simulated scenario reflecting the Fukushima accident releases. Although model variability is important, the intercomparison gives logical results, in that the dynamic models predict consistently a pattern of delayed rise of activity concentration in biota and slow decline instead of the instantaneous equilibrium with the activity concentration in seawater predicted by the ERICA Tool. The differences between ERICA and the dynamic models increase the shorter the TB1/2 becomes; however, there is significant variability between models, underpinned by parameter and methodological differences between them. The need to validate the dynamic models used in this intercomparison has been highlighted, particularly in regards to optimisation of the model biokinetic parameters.

Vives i Batlle, J.↗

Higgs dynamics during inflation

We investigate inflationary Higgs dynamics and constraints on the Standard Model parameters assuming the Higgs potential, computed to next-to-next leading order precision, is not significantly affected by new physics. For a high inflationary scale H ∼ 10{sup 14} GeV suggested by BICEP2, we show that the Higgs is a light field subject to fluctuations which affect its dynamics in a stochastic way. Starting from its inflationary value the Higgs must be able to relax to the Standard Model vacuum well before the electroweak scale. We find that this is consistent with the high inflationary scale only if the top mass m{sub t} is significantly below the best fit value. The region within 2σ errors of the measured m{sub t}, the Higgs mass m{sub h} and the strong coupling α{sub s} and consistent with inflation covers approximately the interval m{sub t}∼<171.8 GeV+0.538(m{sub h}−125.5 GeV) with 125.4 GeV∼<m{sub h}∼<126.3 GeV. If the low top mass region could be definitively ruled out, the observed high inflationary scale alone, if confirmed, would seem to imply new physics necessarily modifying the Standard Model Higgs potential below the inflationary scale.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Final Technical Report: Mathematical Foundations for Uncertainty Quantification in Materials Design

We developed path-wise information theory-based and goal-oriented sensitivity analysis and parameter identification methods for complex high-dimensional dynamics and in particular of non-equilibrium extended molecular systems. The combination of these novel methodologies provided the first methods in the literature which are capable to handle UQ questions for stochastic complex systems with some or all of the following features: (a) multi-scale stochastic models such as (bio)chemical reaction networks, with a very large number of parameters, (b) spatially distributed systems such as Kinetic Monte Carlo or Langevin Dynamics, (c) non-equilibrium processes typically associated with coupled physico-chemical mechanisms, driven boundary conditions, hybrid micro-macro systems, etc. A particular computational challenge arises in simulations of multi-scale reaction networks and molecular systems. Mathematical techniques were applied to in silico prediction of novel materials with emphasis on the effect of microstructure on model uncertainty quantification (UQ). We outline acceleration methods to make calculations of real chemistry feasible followed by two complementary tasks on structure optimization and microstructure-induced UQ.

97 MATHEMATICS AND COMPUTING↗

An analysis of parameters affecting ampacity in aircraft bipolar MVDC power cables via coupled electrical, thermal, and computational fluid dynamic modelling

Abstract The next generation of aircraft, including more electric aircraft and all‐electric aircraft (AEA), requires electric power systems with high power density and low system mass specifications. Increasing the voltage of the system to the range of a few kV, medium voltage (MV), is a reasonable approach to achieving high‐power‐density and low‐system‐mass EPSs for aircraft applications. Higher voltages, however, pose many challenges for aviation MV power cables such as arcs and arc tracking, partial discharges (PDs), and thermal management. In this regard, thermal management is more challenging since heat transfer by convection is greatly reduced at wide‐body aircraft's cruising altitudes due to the reduced air pressure. In this paper, a finite element method (FEM) model is developed in COMSOL Multiphysics for an aircraft bipolar MVDC (±5 kV) power cable. Using the model, the maximum permissible cable current at a low pressure of 18.8 kPa (at an altitude of 12.2 km from sea level, the usual cruising altitude for wide‐body aircraft) is calculated. Also, an analytical model is developed based on analytical and proven empirical correlations governing conductive, radiative, and convective heat transfers at the steady state to estimate the ampacity of the bipolar cable system at reduced pressure. It was shown that the proposed analytical model can be used for atmospheric pressure and systems with a larger number of poles, expanding its range of applications. The results of the FEM and analytical models correlate at wide ranges of parameters such as ambient temperature, duct size, distance between the positive and negative pole cables, and the overall diameter of the cables. The influence of horizontal and vertical arrangement of poles is included in the analytical model. The results of this study can be used to design bipolar MVDC power cable systems for the envisaged wide‐body AEA.

Azizi, Arian↗