Search NASA⌕ Search

SEARCH · Search NASA

Results for “EXPERIMENTATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

An experimental and theoretical evaluation of increased thermal diffusivity phase change devices

This study was to experimentally evaluate and mathematically model the performance of phase change thermal control devices containing high thermal conductivity metal matrices. Three aluminum honeycomb filters were evaluated at five different heat flux levels using n-oct-adecane as the test material. The system was mathematically modeled by approximating the partial differential equations with a three-dimensional implicit alternating direction technique. The mathematical model predicts the system quite well. All of the phase change times are predicted. The heating of solid phase is predicted exactly while there is some variation between theoretical and experimental results in the liquid phase. This variation in the liquid phase could be accounted for by the fact that there are some heat losses in the cell and there could be some convection in the experimental system.

White, S. P.↗
NASA NTRS1972

An experimental-theoretical study of free vibrations of plates on elastic point supports

A theoretical and experimental study is made to investigate the effect on plate vibrations of varying the stiffness of corner elastic point supports. A theoretical model is developed using a Rayleigh-Ritz analysis which approximates the plate mode shapes as products of free-free beam modes. The elastic point supports are modelled both as massless translational springs, and springs with tip masses. The tip masses are included to better represent the experimental supports. An experiment is constructed using the bending stiffness of horizontal beams to support a square plate at its four corners. The stiffness of these supports can be varied over such a range that the plate fundamental frequency is lowered to 40% of the rigid support frequency. The variation with support stiffness of the frequencies of the first eight plate modes is measured, and compared with the theoretical results. The plate mode shapes for rigid supports are analyzed using holographic interferometry. There is excellent agreement between the theoretical and experimental results, except for high plate modes where the theoretical model is demonstrated to be inadequate.

Leuner, T. R.↗
NASA NTRS1973

Theoretical and experimental internal flow characteristics of a 13.97-centimeter-diameter inlet at STOL takeoff and approach conditions

The theoretical and experimental internal flow characteristics of a 13.97-cm-diam inlet with centerbody retracted and extended are presented at STOL takeoff and approach operating conditions. The theoretical results were obtained from incompressible potential flow corrected for compressibility and boundary layer. Comparisons between theoretical internal surface static-pressure distributions and experimental data are presented for free-stream velocities of 0, 24, 32, and 45 m/sec for a range of inlet incidence angles from 0 to 50 deg. Surface static-pressure distributions are illustrated at circumferential locations of 0, 60, 120, and 180 deg. Surface Mach number distributions from the stagnation point to the diffuser exit are presented along with turbulent boundary-layer shape factors. In general, good agreement was found between the theoretical and experimental surface static pressure distributions.

Albers, J. A.↗
NASA NTRS1973

Analytical and experimental performance of optimal controller designs for a supersonic inlet

The techniques of modern optimal control theory were applied to the design of a control system for a supersonic inlet. The inlet control problem was approached as a linear stochastic optimal control problem using as the performance index the expected frequency of unstarts. The details of the formulation of the stochastic inlet control problem are presented. The computational procedures required to obtain optimal controller designs are discussed, and the analytically predicted performance of controllers designed for several different inlet conditions is tabulated. The experimental implementation of the optimal control laws is described, and the experimental results obtained in a supersonic wind tunnel are presented. The control laws were implemented with analog and digital computers. Comparisons are made between the experimental and analytically predicted performance results. Comparisons are also made between the results obtained with continuous analog computer controllers and discrete digital computer versions.

Zeller, J. R.↗
NASA NTRS1973

A study of the thermoregulatory characteristics of a liquid-cooled garment with automatic temperature control based on sweat rate: Experimental investigation and biothermal man-model development

Experimental results for three subjects walking on a treadmill at exercise rates of up to 590 watts showed that thermal comfort could be maintained in a liquid cooled garment by using an automatic temperature controller based on sweat rate. The addition of head- and neck-cooling to an Apollo type liquid cooled garment increased its effectiveness and resulted in greater subjective comfort. The biothermal model of man developed in the second portion of the study utilized heat rates and exchange coefficients based on the experimental data, and included the cooling provisions of a liquid-cooled garment with automatic temperature control based on sweat rate. Simulation results were good approximations of the experimental results.

Chambers, A. B.↗
NASA NTRS1974

Experimental and analytical determination of vibration characteristics of corrugated, flexibly supported, heat-shield panels

Experimental and analytical natural frequencies, nodal patterns, and typical modal displacements for a corrugated, flexibly supported, heat-shield panel are discussed. Good correlation was found between the experimental data and NASTRAN analytical results for the corrugated panel over a relatively wide frequency spectrum covered in the investigation. Of the two experimental techniques used for mode shape and displacement measurements (a noncontacting displacement sensor system and a holographic technique using a helium-neon, continuous-wave laser), the holographic technique was found, in the present investigation, to be faster and better suited for determining a large number of complex nodal patterns of the corrugated panel.

Carden, H. D.↗
NASA NTRS1974

Comparison of interference-free numerical results with sample experimental data for the AEDC wall-interference model at transonic and subsonic flow conditions

Numerical results obtained from two computer programs recently developed with NASA support and now available for use by others are compared with some sample experimental data taken on a rectangular-wing configuration in the AEDC 16-Foot Transonic Tunnel at transonic and subsonic flow conditions. This data was used in an AEDC investigation as reference data to deduce the tunnel-wall interference effects for corresponding data taken in a smaller tunnel. The comparisons were originally intended to see how well a current state-of-the-art transonic flow calculation for a simple 3-D wing agreed with data which was felt by experimentalists to be relatively interference-free. As a result of the discrepancies between the experimental data and computational results at the quoted angle of attack, it was then deduced from an approximate stress analysis that the sting had deflected appreciably. Thus, the comparisons themselves are not so meaningful, since the calculations must be repeated at the proper angle of attack. Of more importance, however, is a demonstration of the utility of currently available computational tools in the analysis and correlation of transonic experimental data.

Newman, P. A.↗
NASA NTRS1974

Analytical and experimental investigation of flow fields of annular jets with and without swirling flow

Analytical and experimental studies were performed to define the flowfield of annular jets, with and, without swirling flow. The analytical model treated configurations with variations of flow angularities, radius ratio, and swirl distributions. Swirl distributions characteristic of stator vanes and rotor blade rows, where the total pressure and swirl distributions are related were incorporated in the mathematical model. The experimental studies included tests of eleven nozzle models, both with and, without swirling exhaust flow. Flowfield surveys were obtained and used for comparison with the analytical model. This comparison of experimental and analytical studies served as the basis for evaluation of several empirical constants as required for application of the analysis to the general flow configuration. The analytical model developed during these studies is applicable to the evaluation of the flowfield and overall performance of the exhaust of statorless lift fan systems that contain various levels of exhaust swirl.

Simonson, M. R.↗
NASA NTRS1975

Experimentally determined stiffness and damping of an inherently compensated air squeeze-film damper

Values of damping and stiffness were determined experimentally for an externally pressurized, inherently compensated, compressible squeeze-film damper up to excitation frequencies of 36,000 cycles per minute. Experimental damping values were higher than theory predicted at low squeeze numbers and less than predicted at high squeeze numbers. Experimental values of air film stiffness were less than theory predicted at low squeeze numbers and much greater at higher squeeze numbers. Results also indicate sufficient damping to attenuate amplitudes and forces at the critical speed when using three dampers in the flexible support system of a small, lightweight turborotor.

Cunningham, R. E.↗
NASA NTRS1976

Tests of a reduced-scale experimental model of a building solar heating-cooling system

An experimental solar heating and cooling system model has been built and operated, combining elements that are programmable (e.g., heating and cooling load of a building and collected solar energy) with experimental equipment. The experimental system model was based on the loads and components used in the Solar Building Test Facility (SBTF), which includes a 1394 sq m solar collector field at NASA Langley. These tests covered 5 continuous days under summer conditions. For the system model up to 55 percent of the simulated collected solar energy was used for the building load. This amount of solar energy supplied 35 percent of the building cooling load. Heat loss was significant. If tank heat loss were eliminated, which would make it similar to the actual SBTF, 75 percent of the collected solar energy would be used. This amount would supply approximately 50 percent of the building cooling load. A higher fraction of solar energy is possible with a more performance-optimized system.

Namkoong, D.↗
NASA NTRS1976

An analytical and experimental evaluation of a Fresnel lens solar concentrator

An analytical and experimental evaluation of line focusing Fresnel lenses with application potential in the 200 to 370 C range was studied. Analytical techniques were formulated to assess the solar transmission and imaging properties of a grooves down lens. Experimentation was based on a 56 cm wide, f/1.0 lens. A Sun tracking heliostat provided a nonmoving solar source. Measured data indicated more spreading at the profile base than analytically predicted, resulting in a peak concentration 18 percent lower than the computed peak of 57. The measured and computed transmittances were 85 and 87 percent, respectively. Preliminary testing with a subsequent lens indicated that modified manufacturing techniques corrected the profile spreading problem and should enable improved analytical experimental correlation.

Hastings, L. J.↗
NASA NTRS1977

Experimental studies of trailing-edge conditions on an oscillating airfoil at frequency parameters of up to one

This paper describes an investigation to find the range of reduced frequencies over which the classical Kutta-Joukowsky condition is valid and the nature of deviations beyond this range. An NACA 64A010 airfoil with a 15-cm chord is supported between the side walls of a 25-cm x 35-cm low-speed wind tunnel and oscillated over reduced frequencies ranging from 0.05 to 1.2. The experimentally determined loading near the trailing edge is measured and compared with unsteady incompressible small-disturbance theory. Experimental data are obtained both with and without a boundary-layer trip. It is observed that application of the Kutta-Joukowsky condition in the theoretical analysis is valid below a reduced frequency of about 0.6 in predicting the loading in the trailing-edge region. At reduced frequencies beyond 0.8, the predicted results underestimate the measured loading near the trailing edge, and the deviations increase further with reduced frequency. Similarly, the experimental phase angle of the loading in the trailing-edge region agrees reasonably with the linear theory up to k = 0.8 but lags the predicted value beyond k = 0.8.

Satyanarayana, B.↗
NASA NTRS1977

NASA/Pratt and Whitney experimental clean combustor program: Engine test results

A two-stage vorbix (vortex burning and mixing) combustor and associated fuel system components were successfully tested in an experimental JT9D engine at steady-state and transient operating conditions, using ASTM Jet-A fuel. Full-scale JT9D experimental engine tests were conducted in a phase three aircraft experimental clean combustor program. The low-pollution combustor, fuel system, and fuel control concepts were derived from phase one and phase two programs in which several combustor concepts were evaluated, refined, and optimized in a component test rig. Significant pollution reductions were achieved with the combustor which meets the performance, operating, and installation requirements of the engine.

Roberts, R.↗
NASA NTRS1978

A parametric experimental study of the interference effects and the boundary-condition coefficient of slotted wind-tunnel walls

An experimental study of slotted upper and lower walls in a two-dimensional transonic wind tunnel with solid sidewalls is reported. Results are presented for several slot spacings and slot openness ratios. The experimental data are pressure measurements which were made on an airfoil model and on a sidewall near one of the slotted walls. The slotted-wall boundary-condition coefficient, which relates the pressure and streamline curvature near the wall, is determined from the wall pressure measurements. The measured wall-induced interference is correlated with the experimental values for the boundary-condition coefficient. This correlation is compared with theory.

Everhart, J. L.↗
NASA NTRS1978

A parametric experimental study of the slotted-wall boundary condition

An experimental study of slotted upper and lower walls in a two dimensional transonic wind tunnel with solid sidewalls is reported. Results are presented for several slot spacings and slot openness ratios. The experimental data were pressure measurements which were made on an airfoil model and on a sidewall near one of the slotted walls. The slotted-wall boundary condition coefficient, which related the pressure and streamline curvature near the wall, was determined from the wall pressure measurements. The measured wall-induced interference was correlated with the experimental values for the boundary condition coefficient. This correlation was compared with theory.

Everhart, J. L.↗
NASA NTRS1978

An analytical and experimental study of sound propagation and attenuation in variable-area ducts

The performance of sound suppression techniques in ducts that produce refraction effects due to axial velocity gradients was evaluated. A computer code based on the method of multiple scales was used to calculate the influence of axial variations due to slow changes in the cross-sectional area as well as transverse gradients due to the wall boundary layers. An attempt was made to verify the analytical model through direct comparison of experimental and computational results and the analytical determination of the influence of axial gradients on optimum liner properties. However, the analytical studies were unable to examine the influence of non-parallel ducts on the optimum linear conditions. For liner properties not close to optimum, the analytical predictions and the experimental measurements were compared. The circumferential variations of pressure amplitudes and phases at several axial positions were examined in straight and variable-area ducts, hard-wall and lined sections with and without a mean flow. Reasonable agreement between the theoretical and experimental results was obtained.

Nayfeh, A. H.↗
NASA NTRS1979

A comparison of simulated and experimental wave spectra in the nearshore region

The results of comparing the experimental spectra measured over the shelf with spectra measured in deepwater conditions indicated that statistically significant changes occurred over the shelf region that could be attributed to shoaling and refraction effects. The comparison of the simulated spectra with the experimental agreed well at the 80% confidence level for all but the most inshore data segment. The total energy also showed similar agreement. However, the theoretical frequency at which peak spectral density occurred did not follow the decreasing trend seen in the experimental data. Guidelines are proposed for determining the type wavefield to which the modeling technique can best be applied, and caution is given on the selection of the digitization rate necessary to ensure sufficient detail for analysis of wave data.

Morris, W. D.↗