Search NASA⌕ Search

SEARCH · Search NASA

Results for “Flow separation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60

An algebraic RNG-based turbulence model for three-dimensional turbomachinery flows

An algebraic eddy viscosity turbulence model based on Renormalization Group (RNG) theory for complex three-dimensional turbomachinery flows is presented. Modifications are made to the baseline RNG model for wakes and separated flows. The model has several advantages over popular algebraic models most notably its lack of empirically determined coefficients. The model is used to compute the mean flow in a low speed axial compressor rotor. The agreement with blade boundary layer and radial flow experimental data is very good and shows improvement over the Baldwin-Lomax model. The development of the tip leakage vortex is also well predicted. The computed wake decay also compares favorably with recent experimental data.

Kirtley, K. R.↗

Hypersonic rarefied flow about a compression corner - DSMC simulation and experiment

The phenomena of shock/boundary-layer interactions and flow separation are investigated using both computational and experimental methods for low-density hypersonic flow about two-dimensional compression corners. The numerical calculations are made with the direct simulation Monte Carlo (DSMC) method. Experimental measurements provide information concerning the flowfield structure and surface flow patterns by means of gas glow discharge and oil flow pictures, respectively. Comparison of the two data sets provides a qualitative basis for assessing the ability of the DSMC method to describe such flows.

Moss, James N.↗

Nonequilibrium turbulence modeling effects on transonic vortical flows about delta wings

The Johnson-King turbulence model that is a viable method for calculating two dimensional transonic separated flows was extended into three dimensions. The implementation was done for Navier Stokes flow solvers written in general curvilinear coordinates. The present approach used in turbulence modeling is based on streamwise integration of an ordinary differential equation (o.d.e.) that governs the maximum Reynolds shear stress behavior. Streamwise integration of the o.d.e. approach was found to offer great mathematical simplicity and economy for three dimensional Navier Stokes methods. Thus, the new method is quick, simple, and very cheap. The new method was first checked against the data of a well known transonic axisymmetric bump experiment, and a good agreement was obtained. Later, the new method was used to compute the flow around a low aspect ratio wing in a transonic wind tunnel. Finally it was employed to study the nonequilibrium turbulence effects on the transonic vortical flows about a 65 deg sweep round leading edge delta wing.

Unver Kaynak↗

Control of unsteady shock-induced turbulent boundary layer separation upstream of blunt fins

Fluctuating wall pressure measurements have been made on centerline upstream of blunt fins in a Mach 5 turbulent boundary layer. Standard time series analysis and conditional sampling algorithms have been used to examine the effects of leading edge sweepback, leading edge shape, and fin root modifications on the fluctuating pressures. Leading edge sweep considerably reduces the mean and rms pressure loading at the fin root, the extent of the region of unsteady separation shock motion, and the separation length. The frequency of pressure fluctuations in the intermittent region increases with leading edge sweepback, while the spectral content of pressure fluctuations in the separated region is virtually unchanged by leading edge sweep. A swept hemicylindrically blunted root fillet reduces the centerline upstream influence and intermittent region length by 50 percent, and reduces the mean and rms pressure loading at the fin root by about 75 percent and 95 percent respectively. Experiments using hemicylindrical, wedge shaped and flat leading edges show that while separated flow scales increase with increasing 'bluntness', intermittent region length and root loading decrease, and separation shock frequency increases.

Kleifges, K.↗

Pressure Distributions and Wave Drag Due to Two-Dimensional Fabrication-Type Surface Roughness on an Ogive Cylinder at Mach Numbers of 1.61 and 2.01

An investigation has been made at Mach numbers of 1.61 and 2.01 and over a range of free-stream Reynolds number per foot from about 1.2 x 10(exp 6) to 8.3 x 10(exp 6) to determine the pressure distributions and wave drags due to two-dimensional fabrication-type surface roughness. Ten types of surface roughness, including step, wave, crease, and swept configurations were investigated. The tests were made on an ogive cylinder of fineness ratio 12.2, the roughness elements covering the cylindrical portion of the model. The results indicate that wave drag is the major component of the drag due to roughness at supersonic speeds. The pressure distributions over the roughness elements were generally found to be in good agreement with linearized two-dimensional theory except for regions of the elements affected by boundary-layer separation and shock detachment. There was little or no effect of Reynolds number except on the pressures within the regions influenced by separation or shock detachment. Inasmuch as most of the roughness configurations were affected by flow separation and shock detachment, there was generally an effect of Reynolds number on the roughness wave drag. This wave drag decreased as the free-stream Reynolds number was decreased.

Czarnecki, K. R.↗

Predicting Flutter and Forced Response in Turbomachinery

TURBO-AE is a computer code that enables detailed, high-fidelity modeling of aeroelastic and unsteady aerodynamic characteristics for prediction of flutter, forced response, and blade-row interaction effects in turbomachinery. Flow regimes that can be modeled include subsonic, transonic, and supersonic, with attached and/or separated flow fields. The three-dimensional Reynolds-averaged Navier-Stokes equations are solved numerically to obtain extremely accurate descriptions of unsteady flow fields in multistage turbomachinery configurations. Blade vibration is simulated by use of a dynamic-grid-deformation technique to calculate the energy exchange for determining the aerodynamic damping of vibrations of blades. The aerodynamic damping can be used to assess the stability of a blade row. TURBO-AE also calculates the unsteady blade loading attributable to such external sources of excitation as incoming gusts and blade-row interactions. These blade loadings, along with aerodynamic damping, are used to calculate the forced responses of blades to predict their fatigue lives. Phase-lagged boundary conditions based on the direct-store method are used to calculate nonzero interblade phase-angle oscillations; this practice eliminates the need to model multiple blade passages, and, hence, enables large savings in computational resources.

VanZante, Dale E.↗

Perceived Noise Analysis for Offset Jets Applied to Commercial Supersonic Aircraft

A systems analysis was performed with experimental jet noise data, engine/aircraft performance codes and aircraft noise prediction codes to assess takeoff noise levels and mission range for conceptual supersonic commercial aircraft. A parametric study was done to identify viable engine cycles that meet NASA's N+2 goals for noise and performance. Model scale data from offset jets were used as input to the aircraft noise prediction code to determine the expected sound levels for the lateral certification point where jet noise dominates over all other noise sources. The noise predictions were used to determine the optimal orientation of the offset nozzles to minimize the noise at the lateral microphone location. An alternative takeoff procedure called "programmed lapse rate" was evaluated for noise reduction benefits. Results show there are two types of engines that provide acceptable mission range performance; one is a conventional mixed-flow turbofan and the other is a three-stream variable-cycle engine. Separate flow offset nozzles reduce the noise directed toward the thicker side of the outer flow stream, but have less benefit as the core nozzle pressure ratio is reduced. At the systems level for a three-engine N+2 aircraft with full throttle takeoff, there is a 1.4 EPNdB margin to Chapter 3 noise regulations predicted for the lateral certification point (assuming jet noise dominates). With a 10% reduction in thrust just after clearing the runway, the margin increases to 5.5 EPNdB. Margins to Chapter 4 and Chapter 14 levels will depend on the cumulative split between the three certification points, but it appears that low specific thrust engines with a 10% reduction in thrust (programmed lapse rate) can come close to meeting Chapter 14 noise levels. Further noise reduction is possible with engine oversizing and derated takeoff, but more detailed mission studies are needed to investigate the range impacts as well as the practical limits for safety and takeoff regulations.

Turbofans↗

Dynamic stall: An example of strong interaction between viscous and inviscid flows

A study was done of the phenomena concerning profiles in dynamic stall configuration, and more specially those related to pitch oscillations. The most characteristic experimental results on flow separations with a vortex character, and their repercussions on local pressures and total forces were analyzed. Some aspects of the methods for predicting flows with the presence (or not) of boundary layer separation are examined, as well as the main simplified methods available to date for the calculation of total forces in such configurations.

Philippe, J. J.↗

A Computational Study for the Utilization of Jet Pulsations in Gas Turbine Film Cooling and Flow Control

This report is the second part of a three-part final report of research performed under an NRA cooperative Agreement contract. The first part is NASA/CR-2012-217415. The third part is NASA/CR-2012-217417. Jets have been utilized in various turbomachinery applications in order to improve gas turbines performance. Jet pulsation is a promising technique because of the reduction in the amount of air removed from compressor. In this work two areas of pulsed jets applications were computationally investigated using the commercial code Fluent (ANSYS, Inc.); the first one is film cooling of High Pressure Turbine (HPT) blades and second one is flow separation control over Low Pressure Turbine (LPT) airfoil using Vortex Generator Jets (VGJ). Using pulsed jets for film cooling purposes can help to improve the effectiveness and thus allow higher turbine inlet temperature. Effects of the film hole geometry, blowing ratio and density ratio of the jet, pulsation frequency and duty cycle of blowing on the film cooling effectiveness were investigated. As for the low-pressure turbine (LPT) stages, the boundary layer separation on the suction side of airfoils can occur due to strong adverse pressure gradients. The problem is exacerbated as airfoil loading is increased. Active flow control could provide a means for minimizing separation under conditions where it is most severe (low Reynolds number), without causing additional losses under other conditions (high Reynolds number). The effects of the jet geometry, blowing ratio, density ratio, pulsation frequency and duty cycle on the size of the separated region were examined in this work. The results from Reynolds Averaged Navier-Stokes and Large Eddy Simulation computational approaches were compared with the experimental data.

Kartuzova, Olga V.↗

Active Control of Separation From the Flap of a Supercritical Airfoil

Zero-mass-flux periodic excitation was applied at several regions on a simplified high-lift system to delay the occurrence of flow separation. The NASA Energy Efficient Transport (EET) supercritical airfoil was equipped with a 15% chord simply hinged leading edge flap and a 25% chord simply hinged trailing edge flap. Detailed flow features were measured in an attempt to identify optimal actuator placement. The measurements included steady and unsteady model and tunnel wall pressures, wake surveys, arrays of surface hot-films, flow visualization, and particle image velocimetry (PIV). The current paper describes the application of active separation control at several locations on the deflected trailing edge flap. High frequency (F(+) approximately equal to 10) and low frequency amplitude modulation (F(+) sub AM approximately equal to 1) of the high frequency excitation were used for control. It was noted that the same performance gains were obtained with amplitude modulation and required only 30% of the momentum input required by pure sine excitation.

Melton, LaTunia Pack↗

Plume effects on the flow around a blunted cone at hypersonic speeds

Tests at M = 8.2 show that a simulated rocket plume at the base of a blunted cone can cause large areas of separated flow, with dramatic effects on the heat transfer rate distribution. The plume was simulated by solid discs of varying sizes or by an annular jet of gas. Flow over the cone without a plume is fully laminar and attached. Using a large disc, the boundary layer is laminar at separation at the test Reynolds number. Transition occurs along the separated shear layer and the boundary layer quickly becomes turbulent. The reduction in heat transfer associated with a laminar separated region is followed by rising values as transition occurs and the heat transfer rates towards the rear of the cone substantially exceed the values obtained without a plume. With the annular jet or a small disc, separation occurs much further aft, so that heat transfer rates at the front of the cone are comparable with those found without a plume. Downstream of separation the shear layer now remains laminar and the heat transfer rates to the surface are significantly lower than the attached flow values.

Atcliffe, P.↗

Use of experimental separation limits in the theoretical design of V/STOL inlets

Experimental data from several model inlets are used to generate two parameters which are related to the limit of operation for inlet flow separation. One parameter, called the diffusion ratio, is the ratio of the peak velocity on the inlet surface to the velocity at the diffuser exit and is related to the boundary-layer separation at low throat Mach numbers. The other parameter, the peak Mach number on the inlet surface, is related to the separation at high throat Mach numbers. These parameters are easily calculated from potential flow solutions and thus can be used as a design tool in screening proposed inlet geometries. An illustrative example of an application to an inlet design study for a tilt nacelle VTOL airplane is presented. The value of contraction ratio required to meet the operating requirements yet allow the inlet to remain free of separation as indicated by the two separation parameters is shown.

Boles, M. A.↗

Flow prediction over a transport multi-element high-lift system and comparison with flight measurements

Accurate prediction of surface-pressure distributions, merging boundary-layers, and separated-flow regions over multi-element high-lift airfoils is required to design advanced high-lift systems for efficient subsonic transport aircraft. The availability of detailed measurements of pressure distributions and both averaged and time-dependent boundary-layer flow parameters at flight Reynolds numbers is critical to evaluate computational methods and to model the turbulence structure for closure of the flow equations. Several detailed wind-tunnel measurements at subscale Reynolds numbers were conducted to obtain detailed flow information including the Reynolds-stress component. As part of a subsonic-transport high-lift research program, flight experiments are conducted using the NASA-Langley B737-100 research aircraft to obtain detailed flow characteristics for support of computational and wind-tunnel efforts. Planned flight measurements include pressure distributions at several spanwise locations, boundary-layer transition and separation locations, surface skin friction, as well as boundary-layer profiles and Reynolds stresses in adverse pressure-gradient flow.

Vijgen, P. M. H. W.↗

Leeward flow over delta wings at supersonic speeds

A survey was made of the parameters affecting the development of the leeward symmetric separated flow over slender delta wings immersed in a supersonic stream. The parameters included Mach number, Reynolds number, angle of attack, leading-edge sweep angle, and body cross-sectional shape, such that subsonic and supersonic leading-edge flows are encountered. It was seen that the boundaries between the various flow regimes existing about the leeward surface may conveniently be represented on a diagram with the components of angle of attack and Mach number normal to the leading edge as governing parameters.

Szodruch, J. G.↗

An experimental investigation of the separating/reattaching flow over a backstep

Reynolds number effects on the evolution of the turbulence structure in the recovery region of a turbulent separated flow generated by a backward-facing step were studied experimentally. Five different flow conditions and four Reynolds numbers were investigated. All single point measurements were conducted on the plane of symmetry of the wind tunnel starting at approximately x/h = 10 for each flow condition. The upper limit of the measuring domain depends upon the physical size of the tunnel and ranged from 50 to 114 step heights. It is apparent that most of the boundary layer recovery was captured by the experiment. Normal stresses, shear stress, mixing length scales and eddy viscosity are shown, while the higher order velocity products related to the diffusion of the turbulence energy are planned for latter stages of the data analysis.

Jovic, Srboljub↗

Use of experimental separation limits in the theoretical design of V/STOL inlets

Experimental data from several model inlets have been used to generate two parameters which are related to the limit of operation for inlet flow separation. One parameter, called the diffusion ratio, is the ratio of the peak velocity on the inlet surface to the velocity at the diffuser exit and is related to the boundary-layer separation at low throat Mach numbers. The other parameter, the peak Mach number on the inlet surface, is related to the separation at high throat Mach numbers. These parameters are easily calculated from potential flow solutions and thus can be used as a design tool in screening proposed inlet geometries. Any of the geometric design variables can be analyzed by this technique; but, this paper is restricted to the consideration of the internal lip contraction ratio. An illustrative example of an application to an inlet design study for a tilt nacelle VTOL airplane is presented. The study will show what value of contraction ratio is required to meet the operating requirements yet allow the inlet to remain free of separation as indicated by the two separation parameters.

Boles, M. A.↗

First observation and characterization of vortex flow in steel micronozzles for high-pressure diesel injection

Vortex flows can be observed in many industrial systems. One of the most intricate vortex flows is the one formed in high-pressure fuel injector nozzles, which dynamics and influence on initial jet formation have been veiled due to great difficulties in observation of micro-scale fluids enclosed with steel nozzles. In this study, an X-ray tracer imaging method was used to visualize the transient fluid motion in steel micronozzles for the high-pressure diesel injection. The 1 μm-size tungsten particles were added to the diesel so that well-contrasted X-ray images of in-nozzle flows can be recorded with high-energy polychromatic X-ray beams. The X-ray images revealed, for the first time, the transient behavior of vortex flow, vortex-type cavitation and flow separation inside the steel nozzle. The needle-lift dependence of in-nozzle vortex flow dynamics was then modeled and correlated to those observed in large-scale optical nozzles in previous studies. Here, the results showed that the in-nozzle vortex and emerging jet flow characteristics of the practical nozzle were similar with those of large-scale nozzles, which suggested that the results of previous fundamental studies can be closely linked to practical cases.

42 ENGINEERING↗

A model of the high-latitude ionospheric convection pattern

Mathematical expressions have been constructed that allow the large-scale global convection characteristics of the high-latitude ionosphere to be reproduced. The model contains no discontinuities in the ion convection velocity and as such should be useful in F region chemical models. The number of variables in the model allow such features as the dayside throat and the Harang discontinuity to be modeled. The applicability of the model to magnetospheric physics is limited by the exclusion of large-magnitude small-scale flow features associated with discrete arcs and by the inability of the model to produce separate flow cells at the same local time.

Heelis, R. A.↗