Search NASA⌕ Search

SEARCH · Search NASA

Results for “Linearization error”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60

Influence of Strain-Gage Balance Characteristics on the Precision Error of the Drag Coefficient

Improvements and results of a new method are presented that computes a pre-test estimate of the precision error of the drag coefficient of a wind tunnel model. The error estimate is defined as the part of the drag coefficient's precision error that is primarily associated with the precision error of the angle of attack measurement and physical characteristics of the chosen strain-gage balance. The method indirectly describes the precision error of the angle of attack measurement by using an assumed balance gage output variation of one microV/V. The physical characteristics of the balance, on the other hand, are described by partial derivatives of the axial and normal forces with respect to the strain-gage outputs. These derivatives can directly be obtained from the data reduction matrix of the balance. The precision error estimate itself is calculated by applying a simple explicit equation that uses the model reference area, the dynamic pressure, the angle of attack, the coefficients of the linear terms of the data reduction matrix, and the electrical output variation of one microvolt per volt as input. Precision errors at constant angle of attack may be visualized as contour plots by plotting them, for example, versus the Mach number and the total pressure. Characteristics of NASA's MC60E balance are used in combination with the reference area of a generic wind tunnel model in order to demonstrate that error estimates are independent of both the balance load format and the units chosen for the description of balance loads, model reference area, and the dynamic pressure. Finally, experimental data from a wind tunnel test of the Ames Check Standard Model in the NASA Ames 11-foot Transonic Wind Tunnel illustrates the application of the method to real-world test data.

precision error↗

PULSAR TIMING ERRORS FROM ASYNCHRONOUS MULTI-FREQUENCY SAMPLING OF DISPERSION MEASURE VARIATIONS

Free electrons in the interstellar medium cause frequency-dependent delays in pulse arrival times due to both scattering and dispersion. Multi-frequency measurements are used to estimate and remove dispersion delays. In this paper, we focus on the effect of any non-simultaneity of multi-frequency observations on dispersive delay estimation and removal. Interstellar density variations combined with changes in the line of sight from pulsar and observer motions cause dispersion measure (DM) variations with an approximately power-law power spectrum, augmented in some cases by linear trends. We simulate time series, estimate the magnitude and statistical properties of timing errors that result from non-simultaneous observations, and derive prescriptions for data acquisition that are needed in order to achieve a specified timing precision. For nearby, highly stable pulsars, measurements need to be simultaneous to within about one day in order for the timing error from asynchronous DM correction to be less than about 10 ns. We discuss how timing precision improves when increasing the number of dual-frequency observations used in DM estimation for a given epoch. For a Kolmogorov wavenumber spectrum, we find about a factor of two improvement in precision timing when increasing from two to three observations but diminishing returns thereafter.

79 ASTRONOMY AND ASTROPHYSICS↗

Spectral contaminant identifier for off-axis integrated cavity output spectroscopy measurements of liquid water isotopes

Developments in cavity-enhanced absorption spectrometry have made it possible to measure water isotopes using faster, more cost-effective field-deployable instrumentation. Several groups have attempted to extend this technology to measure water extracted from plants and found that other extracted organics absorb light at frequencies similar to that absorbed by the water isotopomers, leading to {delta}{sup 2}H and {delta}{sup 18}O measurement errors ({Delta}{delta}{sup 2}H and {Delta}{delta}{sup 18}O). In this note, the off-axis integrated cavity output spectroscopy (ICOS) spectra of stable isotopes in liquid water is analyzed to determine the presence of interfering absorbers that lead to erroneous isotope measurements. The baseline offset of the spectra is used to calculate a broadband spectral metric, m{sub BB}, and the mean subtracted fit residuals in two regions of interest are used to determine a narrowband metric, m{sub NB}. These metrics are used to correct for {Delta}{delta}{sup 2}H and {Delta}{delta}{sup 18}O. The method was tested on 14 instruments and {Delta}{delta}{sup 18}O was found to scale linearly with contaminant concentration for both narrowband (e.g., methanol) and broadband (e.g., ethanol) absorbers, while {Delta}{delta}{sup 2}H scaled linearly with narrowband and as a polynomial with broadband absorbers. Additionally, the isotope errors scaled logarithmically with m{sub NB}. Using the isotope error versus m{sub NB} and m{sub BB} curves, {Delta}{delta}{sup 2}H and {Delta}{delta}{sup 18}O resulting from methanol contamination were corrected to a maximum mean absolute error of 0.93 per mille and 0.25 per mille respectively, while {Delta}{delta}{sup 2}H and {Delta}{delta}{sup 18}O from ethanol contamination were corrected to a maximum mean absolute error of 1.22 per mille and 0.22 per mille . Large variation between instruments indicates that the sensitivities must be calibrated for each individual isotope analyzer. These results suggest that the properly calibrated interference metrics can be used to correct for polluted samples and extend off-axis ICOS measurements of liquid water to include plant waters, soil extracts, wastewater, and alcoholic beverages. The general technique may also be extended to other laser-based analyzers including methane and carbon dioxide isotope sensors.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Inertial navigation systems analysis.

This volume offers the avionic systems engineer a fundamental exposition of the mechanization and error analysis of inertial navigation systems. While the material is applicable to spacecraft and undersea navigation, emphasis is placed upon terrestrial applications on or slightly above the earth's surface. As a result, practical considerations are geared toward those aircraft navigation systems of particular current interest. Extensive use is made of perturbation techniques to develop linearized system equations, whose solutions closely approximate those obtained by nonlinear differential equations. A unified error analysis technique is developed that is applicable to virtually all system configurations. The technique provides a greatly simplified method for comparing the performance of competing system configurations.

Britting, K. R.↗

Realistic Covariance Generation for the GPM Spacecraft

A covariance realism process for NASA's Global Precipitation Measurement (GPM) spacecraft is detailed. The GPM spacecraft is in a low earth orbit, and performs collision avoidance maneuvers few times a year. Currently GPM is below the International Space Station (ISS). So, in addition to cataloged debris objects, GPM must contend with smallsat/cubesat objects that are deployed from the ISS. Both operational scenarios require complete knowledge of the expected GPM prediction errors as a function of time. In this study, we present a method for generating realistic predicted covariance that uses linear propagation of the covariance with the addition of process noise. Further analyses are presented for the process noise ''tuning'' that generates an inflation factor based on the observed error statistics of the predictive satellite trajectories when compared to the definitive ones. Different tuning strategies are considered and compared via a Goodness-of-Fit testing for the Gaussian properties of the scaled covariance. SpaceNav's realistic covariance generation approach takes into account the contribution of predicted maneuver errors in the increased propagation uncertainty. Corresponding maneuver uncertainty is injected into the state uncertainty, and is used within the collision avoidance process to determine the collision risk for close approach events that follow a maneuver. This is a critical step in the maneuver planning process that provides the satellite operator with an accurate quantification of the collision probability for planned maneuvers. Using this information, an informed decision can be made to proceed with a maneuver if the collision risk is acceptable. This approach is validated by Monte-Carlo simulations and results are presented.

spacecraft uncertainty propagation↗

Performance improvements of wavelength-shifting-fiber neutron detectors using high-resolution positioning algorithms

On the basis of FluoroBancroft linear-algebraic method [S.B. Andersson, Opt. Exp. 16, 18714 (2008)] three highly-resolved positioning methods were proposed for wavelength-shifting fiber (WLSF) neutron detectors. Using a Gaussian or exponential-decay light-response function (LRF), the non-linear relation of photon-number profiles vs. x-pixels was linearized and neutron positions were determined. The proposed algorithms give an average 0.03-0.08 pixel position error, much smaller than that (0.29 pixel) from a traditional maximum photon algorithm (MPA). The new algorithms result in better detector uniformity, less position misassignment (ghosting), better spatial resolution, and an equivalent or better instrument resolution in powder diffraction than the MPA. Moreover, these characters will facilitate broader applications of WLSF detectors at time-of-flight neutron powder diffraction beamlines, including single-crystal diffraction and texture analysis.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Rotatable broadband retarders for far infrared spectroscopic ellipsometry

Rotatable retarders have been developed for applications in spectroscopic, full Mueller Matrix ellipsometry in the far-IR spectral range. Several materials, such as silicon, KRS-5, and a commercial polymer plastic (TOPAS) have been utilized to achieve a fully adjustable retardation between 0{sup o} and 90{sup o}. Experimental characteristics of the rotatable retarders that utilize three- and four-bounce designs are compared with calculations. We discuss the effect of light focusing on the performance of these rotatable retarders. Broadband optical retarders are required for spectroscopic ellipsometry in its full Mueller matrix (MM) realization. Performance of the MM ellipsometer depends on the capability to produce substantially linearly-independent Stokes vectors for the light incident onto the sample. As has been shown, the errors in the measuredMMof the sample are proportional to the condition number of the 4 x 4 matrix composed of the Stokes vectors of four polarization states incident at the sample. It can be proven that it is impossible to cover the Poincare sphere with linearly-independent Stokes vectors by only changing the linear polarization at the input surface of a stationary retarder. As we will illustrate further in this paper, total coverage of the Poincare sphere is possible by rotating a tandem of a linear polarizer and a retarder with a retardation of 90{sup o}. It is this goal that we are trying to achieve in the retarder designs described in this paper.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Low Density Parity Check Codes Based on Finite Geometries: A Rediscovery and More

Low density parity check (LDPC) codes with iterative decoding based on belief propagation achieve astonishing error performance close to Shannon limit. No algebraic or geometric method for constructing these codes has been reported and they are largely generated by computer search. As a result, encoding of long LDPC codes is in general very complex. This paper presents two classes of high rate LDPC codes whose constructions are based on finite Euclidean and projective geometries, respectively. These classes of codes a.re cyclic and have good constraint parameters and minimum distances. Cyclic structure adows the use of linear feedback shift registers for encoding. These finite geometry LDPC codes achieve very good error performance with either soft-decision iterative decoding based on belief propagation or Gallager's hard-decision bit flipping algorithm. These codes can be punctured or extended to obtain other good LDPC codes. A generalization of these codes is also presented.

Kou, Yu↗

Computing in the presence of soft bit errors

It is shown that single-event-upsets (SEUs) due to cosmic rays are a significant source of single bit error in spacecraft computers. The physical mechanism of SEU, electron hole generation by means of Linear Energy Transfer (LET), it discussed with reference made to the results of a study of the environmental effects on computer systems of the Galileo spacecraft. Techniques for making software more tolerant of cosmic ray effects are considered, including: reducing the number of registers used by the software; continuity testing of variables; redundant execution of major procedures for error detection; and encoding state variables to detect single-bit changes. Attention is also given to design modifications which may reduce the cosmic ray exposure of on-board hardware. These modifications include: shielding components operating in LEO; removing low-power Schottky parts; and the use of CMOS diodes. The SEU parameters of different electronic components are listed in a table.

Rasmussen, R. D.↗

Error analysis of low-fidelity models for wake steering based on field measurements

The observations collected by two scanning lidars deployed on the roof of a 2.8-MW turbine undergoing a series of imposed yaw offsets are analyzed. The wake lateral displacement detected by the rear-facing lidar correlates well with the yaw offset sensed by the forward-facing lidar. We find that the high-frequency part of the yaw offset signal is connected to wake meandering, whereas the low frequency component is a good predictor for wake displacement due to yaw misalignment. Conditionally averaged wake velocity data for different yaw offsets are used as benchmarks for the validation of a linearized Reynolds-averaged Navier-Stokes and an empirical wake model. A mean error as low as 2% and a good prediction of the wake trajectory are achieved, provided that the wake recovery rate matches the observations.

17 WIND ENERGY↗

Accuracy of momentum and gyrodensity transport in global gyrokinetic particle-in-cell simulations

Gyrokinetic Particle-In-Cell (PIC) simulations based on conservative Lagrangian formalisms admit transport equations for conserved quantities such as gyrodensity and toroidal momentum, and these can be derived for arbitrary wavelength, even though previous applications have used the long-wavelength approximation. In control-variate PIC simulations, a consequence of the different treatment of the background (f{sub 0}) and perturbed parts (δf), when a splitting f = f{sub 0} + δf is performed, is that analytical transport relations for the relevant fluxes and moments are only reproduced in the large marker number limit. The transport equations for f can be used to write the inconsistency in the perturbed quantities explicitly in terms of the sampling of the background distribution f{sub 0}. This immediately allows estimates of the error in consistency of momentum transport in control-variate PIC simulations. This inconsistency tends to accumulate secularly and is not directly affected by the sources and noise control in the system. Although physical tokamaks often rotate quite strongly, the standard gyrokinetic formalism assumes weak perpendicular flows, comparable to the drift speed. For systems with such weak flows, maintaining acceptably small relative errors requires that a number of markers scale with the fourth power of the linear system size to consistently resolve long-wavelength evolution. To avoid this unfavourable scaling, an algorithm for exact gyrodensity transport has been developed, and this is shown to allow accurate simulations with an order of magnitude fewer markers.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

PDE-constrained high-order mesh optimization

Here, we present a novel framework for PDE-constrained r-adaptivity of high-order meshes. The proposed method formulates mesh movement as an optimization problem, with an objective function defined as a convex combination of a mesh quality metric and a measure of the accuracy of the PDE solution obtained via finite element discretization. The proposed formulation achieves optimized, well-defined high-order meshes by integrating mesh quality control, PDE solution accuracy, and robust gradient regularization. We adopt the Target-Matrix Optimization Paradigm to control geometric properties across the mesh, independent of the PDE of interest. To incorporate the accuracy of the PDE solution, we introduce error measures that control the finite element discretization error. The implicit dependence of these error measures on the mesh nodal positions is accurately captured by adjoint sensitivity analysis. Additionally, a convolution-based gradient regularization strategy is used to ensure stable and effective adaptation of high-order meshes. We demonstrate that the proposed framework can improve mesh quality and reduce the error by up to 10 times for the solution of Poisson and linear elasto-static problems. The approach is general with respect to the dimensionality, the order of the mesh, the types of mesh elements, and can be applied to any PDE that admits well-defined adjoint operators.

Computer science↗

Effective data sampling strategies and boundary condition constraints of physics-informed neural networks for identifying material properties in solid mechanics

Material identification is critical for understanding the relationship between mechanical properties and the associated mechanical functions. However, material identification is a challenging task, especially when the characteristic of the material is highly nonlinear in nature, as is common in biological tissue. In this work, we identify unknown material properties in continuum solid mechanics via physics-informed neural networks (PINNs). To improve the accuracy and efficiency of PINNs, we develop efficient strategies to nonuniformly sample observational data. We also investigate different approaches to enforce Dirichlet-type boundary conditions (BCs) as soft or hard constraints. Finally, we apply the proposed methods to a diverse set of time-dependent and time-independent solid mechanic examples that span linear elastic and hyperelastic material space. The estimated material parameters achieve relative errors of less than 1%. As such, this work is relevant to diverse applications, including optimizing structural integrity and developing novel materials.

97 MATHEMATICS AND COMPUTING↗

Catalytic hydroprocessing of fast pyrolysis oils: Impact of biomass feedstock on process efficiency

Here, we report here on an experimental study to produce refinery-ready fuel blendstocks via catalytic hydrodeoxygenation (upgrading) of pyrolysis oil using several biomass feedstocks and various blends. Blends were tested along with the pure materials to determine the effect of blending on product yields and qualities. Within experimental error, oil yields from fast pyrolysis and upgrading are shown to be linear functions of the blend components. Switchgrass exhibited lower fast pyrolysis and upgrading yields than the woody samples, which included clean pine, oriented strand board (OSB), and a mix of pinon and juniper (PJ). The notable exception was PJ, for which the poor upgrading yield of 18% was likely associated with the very high viscosity of the PJ fast pyrolysis oil (947 cp). The highest fast pyrolysis yield (54% dry basis) was obtained from clean pine, while the highest upgrading yield (50%) was obtained from a blend of 80% clean pine and 20% OSB (CP 8 OSB 2 ). For switchgrass, reducing the fast pyrolysis temperature to 450 degrees C resulted in a significant increase to the pyrolysis oil yield and reduced hydrogen consumption during hydrotreating, but did not directly affect the hydrotreating oil yield. The water content of fast pyrolysis oils was also observed to increase linearly with the summed content of potassium and sodium, ranging from 21% for clean pine to 37% for switchgrass. Multiple linear regression models demonstrate that fast pyrolysis is strongly dependent upon the contents lignin and volatile matter as well as the sum of potassium and sodium.

09 BIOMASS FUELS↗

Array-based, parallel hierarchical mesh refinement algorithms for unstructured meshes

In this paper, we describe an array-based hierarchical mesh refinement capability through uniform refinement of unstructured meshes for efficient solution of PDE's using finite element methods and multigrid solvers. A multi-degree, multi-dimensional and multi-level framework is designed to generate the nested hierarchies from an initial coarse mesh that can be used for a variety of purposes such as in multigrid solvers/preconditioners, to do solution convergence and verification studies and to improve overall parallel efficiency by decreasing I/O bandwidth requirements (by loading smaller meshes and in memory refinement). We also describe a high-order boundary reconstruction capability that can be used to project the new points after refinement using high-order approximations instead of linear projection in order to minimize and provide more control on geometrical errors introduced by curved boundaries.The capability is developed under the parallel unstructured mesh framework "Mesh Oriented dAtaBase" (MOAB Tautges et al. (2004)). We describe the underlying data structures and algorithms to generate such hierarchies in parallel and present numerical results for computational efficiency and effect on mesh quality. Furthermore, we also present results to demonstrate the applicability of the developed capability to study convergence properties of different point projection schemes for various mesh hierarchies and to a multigrid finite-element solver for elliptic problems.

97 MATHEMATICS AND COMPUTING↗

Enhanced MPM framework with multipatch isogeometric analysis for geotechnical applications

Achieving stable stress solutions at large strains using the Material Point Method (MPM) is challenging due to the accumulation of errors associated with geometry discretization, cell-crossing noise, and volumetric locking. Several simplified attempts exist in the literature to mitigate these errors, including higher-order frameworks. However, the stability of the MPM solution in such frameworks has been limited to simple geometries and the single-phase formulation (i.e., neglecting pore fluid). Although never explored, multipatch isogeometric analysis offers desirable qualities to simulate complex geometries while mitigating errors in the MPM. The degree of required high-order spatial integration has also never been investigated to infer a minimum limit for the stability of the stress solution in MPM. This paper presents a general-purpose numerical framework for simulating stable stresses in porous media, capturing both near incompressibility and multiphase interactions. First, the numerical framework is presented considering Non-Uniform Rational B-splines (NURBS) to perform isogeometric analysis (IGA) in MPM. Additionally, a volumetric strain smoothing algorithm is used to alleviate errors associated with volumetric locking. Second, the manifestation of cell-crossing errors is assessed via a series of problems with orders ranging from linear to cubic interpolation functions. Third, the use of NURBS is investigated and verified for problems with circular geometries. Finally, multipatch analysis is deployed to simulate plane strain and 3D penetration in soils, considering nearly incompressible elastoplastic (total stress) analysis and fully-coupled hydro-mechanical (effective stress) analysis. The stability of the solution is also analyzed for different constitutive models. From the results, it can be concluded that the framework using cubic interpolation functions with strain smoothing is the most convenient, presenting stable stress solutions for a broad range of multiphase geotechnical applications.

58 GEOSCIENCES↗

Exploiting Kronecker structure in exponential integrators: Fast approximation of the action of φ $-$functions of matrices via quadrature

Here, in this article, we propose an algorithm for approximating the action of φ $-$ functions of matrices against vectors, which is a key operation in exponential time integrators. In particular, we consider matrices with Kronecker sum structure, which arise from problems admitting a tensor product representation. The method is based on quadrature approximations of the integral form of the φ $-$ functions combined with a scaling and modified squaring method. Owing to the Kronecker sum representation, only actions of 1D matrix exponentials are needed at each quadrature node and assembly of the full matrix can be avoided. Additionally, we derive a priori bounds for the quadrature error, which show that, as expected by classical theory, the rate of convergence of our method is supergeometric. Guided by our analysis, we construct a fast and robust method for estimating the optimal scaling factor and number of quadrature nodes that minimizes the total cost for a prescribed error tolerance. We investigate the performance of our algorithm by solving several linear and semilinear time-dependent problems in 2D and 3D. The results show that our method is accurate and orders of magnitude faster than the current state-of-the-art.

97 MATHEMATICS AND COMPUTING↗

Tests of the DFT Ladder for the Fulminic Acid Challenge

Properties of the historically pivotal fulminic acid (HCNO) molecule have been computed with a panoply of 473 density functionals of all varieties, providing a snapshot of the performance of contemporary density functional theory (DFT) for a challenging chemical system. Exhaustive tabulations and statistical analyses have been carried out for geometric parameters, vibrational frequencies, barriers to linearity, and the HCN–O dissociation energy. As the DFT ladder is climbed, confusion rather than consensus ensues regarding the details of the distinctive, extremely flat H–C–N bending potential of fulminic acid and whether the equilibrium structure is linear or bent. While high-ranking DFT functionals produce the smallest errors for the HCN + O( 3 P) → HCNO reaction energy, lower rungs emerge as the best performers for many of the bond distances and harmonic vibrational frequencies. This research shows that the current DFT zoo of approximations does not constitute a transparent ladder of increasingly accurate methods that consistently converges on definitive predictions for various properties of HCNO. Additional analyses are performed on the side effects of popular dispersion corrections on the covalently bonded properties and thermochemistry of HCNO.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗