Search NASA⌕ Search

SEARCH · Search NASA

Results for “Microstructures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60

Microstructural evolution of an aluminide coating on alloy 625 during wet air exposure at 900 °C and 1000 °C

The microstructural changes of the aluminized alloy 625 during cyclic oxidation in air + 6% H 2 O at 900 °C and 1000 °C were analyzed using optical metallography (OM), scanning electron microscopy (SEM) with energy and wave length dispersive X-ray analysis (EDX/WDX) as well as electron backscatter diffraction (EBSD). An in-house developed thermodynamic-kinetic procedure was employed to predict the microstructural evolution of aluminized alloy 625 during high temperature exposure by considering simultaneously occurring surface oxidation and interdiffusion processes. Because of the lack of mobility data for the relevant alloying elements in the σ-phase, assumptions for the mobilities were made based on the value of the mobilities in α-Cr. Despite these assumptions, the calculated results were found to be in good agreement with experimental observations. The complete depletion of β-NiAl in the coating observed during exposure at 1000 °C was correctly predicted by the model. The model was also able to infer dissolution of the precipitate phases α-Cr and σ in the interdiffusion zone during exposures at 900 °C and 1000 °C. The model was yet unable to predict the formation of the μ-phase in the alloy after 1000 h of exposure at 1000 °C. The developed modelling method offers the potential to predict microstructural changes of aluminized nickel base alloys thus reducing cost and time consuming experimental efforts.

36 MATERIALS SCIENCE↗

Effect of CMAS viscosity on the infiltration depth in thermal barrier coatings of different microstructures

Calcium magnesium aluminum silicate (CMAS) is one of the leading concerns for the gas turbine industry. The effects of CMAS viscosity and the coating microstructure on CMAS infiltration depth were explored by conducting a time dependent interaction study. Three CMAS compositions were used from literature, and their viscosities predicted through FactSage viscosity module were drastically different. The interaction was carried out on three different TBCs synthesized using the solution precursor plasma spray process (SPPS): two of the TBCs were made of yttrium aluminum garnet (YAG) having different microstructures that promote different modes of CMAS infiltration, and one TBC was made of gadolinium zirconate (GZO). All samples had stress relieving vertical cracks and different intensities of horizontally banded porosity, (inter pass boundaries IPBs). A concentration of 100 mg/cm 2 of CMAS was applied on the TBCs which were then subjected to a 5-minute interaction at 1300 °C. Samples were analyzed using scanning electron microscopy (SEM), electron dispersive X-ray spectroscopy (EDXS), and transmission electron microscopy (TEM). Low viscosity CMAS readily penetrated the TBCs while more viscous CMAS showed less penetration. The depth of CMAS infiltration depended on the coating microstructure. In the YAG with IPBs, the CMAS spread horizontally in the IPBs before infiltrating deeper, resulting in reduced infiltration depth compared to other samples in spite of having wider vertical cracks. TEM and EDXS analysis were performed to investigate the phases present in the CMAS-TBC interaction region in YAG. Two regions were chosen, the top TBC surface in direct contact with the sea of CMAS, and the region at the CMAS penetration ended within the coating. Finally, the results showed that no secondary phases like apatite were observed in YAG, thus it can be concluded that the arrest of CMAS happened solely because of CMAS viscosity and the short infiltration time.

36 MATERIALS SCIENCE↗

Microstructural Characterization of Next Generation Nuclear Graphites

This article reports the microstructural characteristics of various petroleum and pitch based nuclear graphites (IG-110, NBG-18, and PCEA) that are of interest to the next generation nuclear plant program. Bright-field transmission electron microscopy imaging was used to identify and understand the different features constituting the microstructure of nuclear graphite such as the filler particles, microcracks, binder phase, rosette-shaped quinoline insoluble (QI) particles, chaotic structures, and turbostratic graphite phase. The dimensions of microcracks were found to vary from a few nanometers to tens of microns. Furthermore, the microcracks were found to be filled with amorphous carbon of unknown origin. The pitch coke based graphite (NBG-18) was found to contain higher concentration of binder phase constituting QI particles as well as chaotic structures. The turbostratic graphite, present in all of the grades, was identified through their elliptical diffraction patterns. The difference in the microstructure has been analyzed in view of their processing conditions.

01 COAL, LIGNITE, AND PEAT↗

Self-Organization and Nitrogen Incorporation in Diamond-Like Carbon Microstructures Synthesized by Nonthermal Plasma

Nonthermal plasma activation of light alkanes is an encouraging decarbonization strategy to produce chemicals or fuels from abundant and/or flared carbon sources. However, prolific carbon growth on both the catalyst and electrode has limited its practicality, requiring additional knowledge of the carbon structure and growth mechanism before breakthroughs are realized. Furthermore, visual evidence is provided for nonuniform diamond-like carbon (DLC) microstructures that materialize in a coaxial dielectric barrier discharge (DBD) reactor flowing ethane and He at 278 K. Through a connection to known behaviors of DBD microdischarge patterns, the microstructure spacing was controlled by altering the applied voltage (ΔV) of the plasma or the burning voltage (U b ). Additionally, carbon valorization through nitrogen incorporation from N 2 was explored as an orthogonal solution to carbon mitigation, with N/C values >0.25 achieved and both sp 2 and sp 3 C–N bonding observed in the microstructures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Investigation of MgO additives on microstructure and properties of thin LLZO electrolytes for all-solid-state batteries

To realize high-energy density lithium lanthanum zirconate (LLZO)-based solid-state batteries (SSB), LLZO electrolytes should be fabricated with low thickness and high mechanical strength. An effective strategy for strengthening ceramic materials is to use additives. Here, we employed MgO nanopowders and fibers as additives for the thin LLZO electrolyte in order to improve the mechanical strength. The microstructure, mechanical properties, and electrochemical properties are characterized to investigate the effects of adding MgO and sintering time. The MgO remains at grain boundaries after sintering, making the microstructure of LLZO fine and uniform. The mechanical strength of the MgO-added LLZO was enhanced by more than 60% while maintaining high ionic conductivity (1 × 10 -4 S cm -1 ) at room temperature. Li symmetric cells using the MgO fiber–LLZO and MgO powder–LLZO exhibit 2 and 3 times higher critical current density (CCD) than those of pure LLZO, and a solid-state full cell exhibits stable cycling performance. Further, these results demonstrate that the use of MgO nanopowder or fiber as an additive for thin LLZO is beneficial for high-current density cycling, by improving mechanical properties and microstructure.

25 ENERGY STORAGE↗

Influence of a Transient Hexagonal Phase on the Microstructure and Morphological Stability of NiSi Films

The morphological stability of NiSi is investigated when 40% of Si is mixed into an as deposited 10 nm Ni film. When annealing at 3?C/s, scanning electron microscopy images and in situ sheet-resistance measurements show that NiSi agglomeration is delayed by more than 100?C. In situ x-ray diffraction reveals that NiSi grows from an unusual transient hexagonal ?-nickel-silicide phase. The significant improvement of the NiSi film's morphological stability can be related to its microstructure, with large grains and a strong texture. This peculiar microstructure is compared to the microstructure of the ?-nickel-silicide precursor by electron backscattering diffraction and pole figures.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Modulating nanomagnetism in Ni{sub 80}Fe{sub 20}/(Ni,Fe)O thin films by tuning the interfacial microstructure using ion bombardment

The strength, polarity, and temperature dependence of the exchange bias field in ferromagnet/antiferromagnet thin film systems depend critically on the nature of the interfacial microstructure. Using ion bombardment during film deposition, we have found a way to modulate the interface microstructure, providing unique control over the exchange bias magnetism. We demonstrate interfacial microstructure modulation in Ni{sub 80}Fe{sub 20}/(Ni,Fe)O thin films, where different ion bombardment energies alter the exchange coupling between the (Ni,Fe)O and Ni{sub 80}Fe{sub 20} interfaces. One interface configuration provides positive or negative exchange coupling depending on whether the film was cooled with or without an external magnetic field, while another interface configuration results in the more typical negative exchange coupling independent of the field cooling.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Characterization of polycrystals with elongated duplex microstructure by inversion of ultrasonic backscattering data

In this letter a simple analytical ultrasonic backscattering model is proposed for determination of characteristic microstructural scales in polycrystalline materials with elongated grains. The inversion methodology for microstructural parameters is based on backscattering coefficient ratios measured in different propagation directions. The ultrasonic backscattering measurements were performed on a Ti alloy sample with a duplex microstructure and the model was applied to experimental data inversion to size the material microtexture.

36 MATERIALS SCIENCE↗

Effects of Al-5Ti-1B master alloy on the microstructural evaluation of a highly alloyed aluminum alloy produced by SIMA process

This study was undertaken to investigate the influence of Al-5Ti-1B master alloy on the structural characteristics of Al-12Zn-3 Mg-2.5Cu aluminum alloy. The optimum amount of Ti containing master alloy for proper grain refining was selected as 6 wt.%. A modified strain-induced, melt-activated (SIMA) process for semi-solid processing of alloys was proposed. In order to examine the effectiveness of the modified SIMA process, the recrystallized microstructures of the Al alloy (Al-12Zn-3 Mg-2.5Cu) prepared by the modified SIMA processes were macroscopically. The modified SIMA process employed casting, warm multi-forging, recrystallization and partial melting instead of the conventional process. Reheating condition to obtain a fine globular microstructure was optimized. The microstructure evolution of reheated Al-12Zn-3 Mg-2.5Cu aluminum alloy was characterized by SEM (Scanning electron microscopy) and optical microscopy. In this study the relation between the induced strain with size and shape of grain size has been studied. Results indicated that with the increase of strain sphericity of particles, their size decreases and sphericity takes place in less reahiting time.

36 MATERIALS SCIENCE↗

Product gas evolution above planar microstructured model catalysts--A combined scanning mass spectrometry, Monte Carlo, and Computational Fluid Dynamics study

The transport and distribution of reaction products above catalytically active Pt microstructures was studied by spatially resolved scanning mass spectrometry (SMS) in combination with Monte Carlo simulation and fluid dynamics calculations, using the oxidation of CO as test reaction. The spatial gas distribution above the Pt fields was measured via a thin quartz capillary connected to a mass spectrometer. Measurements were performed in two different pressure regimes, being characteristic for ballistic mass transfer and diffusion involving multiple collisions for the motion of CO{sub 2} product molecules between the sample and the capillary tip, and using differently sized and shaped Pt microstructures. The tip height dependent lateral resolution of the SMS measurements as well as contributions from shadowing effects, due to the mass transport limitations between capillary tip and sample surface at close separations, were evaluated and analyzed. The data allow to define measurement and reaction conditions where effects induced by the capillary tip can be neglected (''minimal invasive measurements'') and provide a basis for the evaluation of catalyst activities on microstructured model systems, e.g., for catalyst screening or studies of transport effects.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Electron Backscattered Diffraction Analysis Of Narrow Copper Interconnects In Cross-View To Investigate Scale Effect On Microstructure

In this article, we propose to use Electron Backscattered Diffraction (EBSD) to characterize microstructure of copper interconnects of thin metal level in top view and cross view. These two views give very complementary information about microstructure of copper and thus about recrystallization of copper during annealing. Moreover, for minimum width, as interconnect is two times thicker than wide; It will be easier to analyze smaller interconnect of 45 nm node technology in cross-section. We look for evolution of texture and microstructure of copper with line width in top view and in cross view. We highlight the presence of two recrystallization mechanisms and also the fact that transition from one to the other is progressive with competition of both mechanisms.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effect of Controlled Hot Rolling Parameters on Microstructure of a Nb-Microalloyed Steel Sheet

The design of controlled rolling process of microalloyed steel sheets is affected by several factors. In this investigation, effect of the reheating, finishing and coiling temperatures of rolling, which are considered as the most effective parameters on microstructure of hot rolled products has been studied. For this purpose, seven different reheating temperatures between 1000 to 1300 deg. C with 50 deg. C increments, three different finishing temperatures of 950, 900 and 850 deg. C below the non-recrystallization temperature and one temperature of 800 deg. C in the inter critical range and four different coiling temperatures of 550, 600, 650 and 700 deg. C were chosen. By soaking the specimens in furnace, the grain coarsening temperature (T{sub gc}) is obtained about 1250 deg. C. Hence, for these kinds of steels, the reheating temperature 1200 to 1250 deg. C is recommended. Moreover, it is observed that decreasing the coiling and finishing temperatures causes more grain refinement of microstructure and the morphology is changed from polygonal ferrite to acicular one. Findings of this research provide a good connection among reheating, finishing and coiling temperatures and microstructural features of Nb-microalloyed steel sheets.

36 MATERIALS SCIENCE↗

Influence of high power impulse magnetron sputtering plasma ionization on the microstructure of TiN thin films

HIPIMS (High Power Impulse Magnetron Sputtering) discharge is a new PVD technology for the deposition of high-quality thin films. The deposition flux contains a high degree of metal ionization and nitrogen dissociation. The microstructure of HIPIMS-deposited nitride films is denser compared to conventional sputter technologies. However, the mechanisms acting on the microstructure, texture and properties have not been discussed in detail so far. In this study, the growth of TiN by HIPIMS of Ti in mixed Ar and N{sub 2} atmosphere has been investigated. Varying degrees of metal ionization and nitrogen dissociation were produced by increasing the peak discharge current (I{sub d}) from 5 to 30 A. The average power was maintained constant by adjusting the frequency. Mass spectrometry measurements of the deposition flux revealed a high content of ionized film-forming species, such as Ti{sup 1+}, Ti{sup 2+} and atomic nitrogen N{sup 1+}. Ti{sup 1+} ions with energies up to 50 eV were detected during the pulse with reducing energy in the pulse-off times. Langmuir probe measurements showed that the peak plasma density during the pulse was 3 x 10{sup 16} m{sup -3}. Plasma density, and ion flux ratios of N{sup 1+}: N{sub 2}{sup 1+} and Ti{sup 1+}: Ti{sup 0} increased linearly with peak current. The ratios exceeded 1 at 30 A. TiN films deposited by HIPIMS were analyzed by X-ray diffraction, and transmission electron microscopy. At high I{sub d}, N{sup 1+}: N{sub 2}{sup 1+} > 1 and Ti{sup 1+}: Ti{sup 0} > 1 were produced; a strong 002 texture was present and column boundaries in the films were atomically tight. As I{sub d} reduced and N{sup 1+}: N{sub 2}{sup 1+} and Ti{sup 1+}: Ti{sup 0} dropped below 1, the film texture switched to strong 111 with a dense structure. At very low I{sub d}, porosity between columns developed. The effects of the significant activation of the deposition flux observed in the HIPIMS discharge on the film texture, microstructure, morphology and properties are discussed.

36 MATERIALS SCIENCE↗

Texture and microstructure evolution in single-phase Ti{sub x}Ta{sub 1-x}N alloys of rocksalt structure

The mechanisms controlling the structural and morphological features (texture and microstructure) of ternary transition metal nitride thin films of the Ti{sub x}Ta{sub 1-x}N system, grown by various physical vapor deposition techniques, are reported. Films deposited by pulsed laser deposition, dual cathode magnetron sputtering, and dual ion beam sputtering have been investigated by means of x-ray diffraction in various geometries and scanning electron microscopy. We studied the effects of composition, energetic, and kinetics in the evolution of the microstructure and texture of the films. We obtain films with single and mixed texture as well as films with columnar ''zone-T'' and globular type morphology. The results have shown that the texture evolution of ternary transition metal nitrides as well as the microstructural features of such films can be well understood in the framework of the kinetic mechanisms proposed for their binary counterparts, thus giving these mechanisms a global application.

36 MATERIALS SCIENCE↗

Low temperature magnetic behaviour of glass-covered magnetic microwires with gradient nanocrystalline microstructure

Slow nanocrystallization driving dynamics can be affected by the combination of two factors: sample residual stresses and sample geometry. This effect is evidenced at the initial stages of nanocrystallization of amorphous CoFeSiBCuNb magnetic microwires. Transmission electron microscopy observations indicate how crystallization at temperatures between 730 and 780 K results in a graded microstructure where the crystallization at the surface skin of the microwire, which remains almost amorphous, differs from that of the middle, where elongated grains are observed, and inner regions. However, samples annealed at higher temperatures present a homogeneous microstructure. The effect of gradient microstructure on magnetic properties has been also analyzed and a loss of bistable magnetic behaviour at low temperatures, from that obtained in the amorphous and fully nanocrystallized sample, has been observed and ascribed to changes in sign of magnetostriction for measuring temperatures below 100 K.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Fire performance, microstructure and thermal degradation of an epoxy based nano intumescent fire retardant coating for structural applications

Intumescent fire retardant coating (IFRC) is a passive fire protection system which swells upon heating to form expanded multi-cellular char layer that protects the substrate from fire. In this research work, IFRC’s were developed using different flame retardants such as ammonium polyphosphate, expandable graphite, melamine and boric acid. These flame retardants were bound together with the help of epoxy binder and cured together using curing agent. IFRC was then reinforced with nano magnesium oxide and nano alumina as inorganic fillers to study their effect towards fire performance, microstructure and thermal degradation. Small scale fire test was conducted to investigate the thermal insulation of coating whereas fire performance was calculated using thermal margin value. Field emission scanning electron microscopy was used to examine the microstructure of char obtained after fire test. Thermogravimetric analysis was conducted to investigate the residual weight of coating. Results showed that the performance of the coating was enhanced by reinforcement with nano size fillers as compared to non-filler based coating. Comparing both nano size magnesium oxide and nano size alumina; nano size alumina gave better fire performance with improved microstructure of char and high residual weight.

36 MATERIALS SCIENCE↗

The influence of sintering temperature on microstructure and mechanical properties of Ni-Al intermetallics fabricated by SPS

In the present study PN85Yu15 was used as elemental powder to produce a sintered compound with Ni3Al as main phase. The Spark Plasma Sintering (SPS) technique is used to compact the powders. The powder was sintered in a temperature range between 1000°C and 1150°C to observe the influence of the sintering temperature on the microstructure and the mechanical properties. The microstructure was observed with optical microscope (OM), the phase composition was characterized by X-ray diffraction (XRD) technique. Density and microhardness were observed and compared the values with the results of other researchers. The compressive-, density- and microhardness tests show as clear result that with increasing the sintering temperature nearly all properties become better and also the microstructure studies show that porous places become less.

36 MATERIALS SCIENCE↗

Nanoscale microstructure effects on hydrogen behavior in rapidly solidified aluminum alloys

The present work summarizes recent progress in the investigation of nanoscale microstructure effects on hydrogen behavior in rapidly solidified aluminum alloys foils produced at exceptionally high cooling rates. We focus here on the potential of modification of hydrogen desorption kinetics in respect to weak and strong trapping sites that could serve as hydrogen sinks in Al materials. It is shown that it is important to elucidate the surface microstructure of the Al alloy foils at the submicrometer scale because rapidly solidified microstructural features affect hydrogen trapping at nanostructured defects. We discuss the profound influence of solute atoms on hydrogen−lattice defect interactions in the alloys. with emphasis on role of vacancies in hydrogen evolution; both rapidly solidified pure Al and conventionally processed aluminum samples are considered.

36 MATERIALS SCIENCE↗