Search NASA⌕ Search

SEARCH · Search NASA

Results for “RISE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60

Development and Testing of Pulse Guns for Combustion Instability Testing

To test liquid rocket engines (LREs) for combustion instabilities, devices such as bombs are often used to create pressure wave disturbances. Bombs, while effective, are inherently dangerous, expensive, and difficult to procure. Over the years, pulse guns have been used as a safer and more cost-effective way to generate controlled pressure disturbances in engine chambers. In anticipation of the need for stability testing of prototype LREs at NASA Marshall Space Flight Center (MSFC), a set of pulse guns have been designed, fabricated, tested, and characterized. The pulse gun program is funded by the RS-25 Engine Program managed out of MSFC and funded by NASA’s Space Launch System (SLS) through the MSFC Liquid Engines Office (LEO). A pulse gun is a simple device – like a traditional gun, it has a breech and barrel section. However, unlike a traditional gun, there is no bullet, as the purpose of the pulse gun is strictly to fire a high pressure pulse. Instead of a firing pin and primer that would normally be used in a traditional gun, an initiator is used to activate the gun powder. The initiator is a highly reliable pyrotechnic initiator. For this study, clone versions of the NASA Standard Initiator (NSI) were used. The initiator is used to ignite a pre-measured amount of gun powder loaded into the breech. When the pressure of the burnt gun powder exceeds the set point of a downstream burst disk, the disk ruptures, allowing the high pressure pulse to travel downstream through the barrel section. A ballistic pressure transducer located in the breech section is used to measure the short duration, high pressure pulse. Some configurations of the pulse gun have barrel sections that include one or more additional ballistic pressure transducers. These additional pressure measurements help track the degradation and damping of the pulse as it travels out of the barrel section. The measurements may also be used to determine the velocity of pulse. The objective of this paper is to present the different variants of this newly-developed pulse gun and characterize performance over a range of parameters. The parameters include breech diameter, barrel length, amount of gun powder used, the way the gun powder is packed, and the pressure setting of the burst disk. There are a total of six pulse guns: three with the 0.25 inch breech and three different length barrels, and three with the 0.40 inch breech and three different length barrels. For both breech sizes, the associated barrels are referred to as standard, one-port, and two-port barrels. The standard barrel has no instrumentation and is likely the barrel that will be used for engine stability testing. The one- and two-port barrels were designed specifically for pulse gun component testing to allow measurements of the magnitude and timing of the high pressure pulse as it makes its way through the pulse gun. The burst disks tested were commercially-available burst disks designed to rupture at 8,000, 16,000, and 24,000 psid. Testing was accomplished by firing the pulse gun into a test chamber pressurized with nitrogen at about 2300 psig. A total of four Model 113B23 High frequency ICP® pressure sensors (10k psi) were mounted in the test chamber, in the same plane as the pulse gun. Two of the sensors had “trimmed” adapters, and two did not. Given the symmetrical configuration of the sensors within the test chamber, different amplitudes of pressure measurements are attributed to the use of trimmed versus untrimmed adapters. The untrimmed adapters, with their narrower passages, tended to amplify the pressure amplitudes by as much as 50%. In total, 41 pulse gun tests have been conducted.Data are still being analyzed, but some trends are apparent. For example, measurements taken within the pulse gun are shown in Figures 3 and 4 for Hot-fires (HFs) # 11 and 39, respectively. Both tests were identical in that the 0.40 inch ID breech, two-port barrel, 8,000 psid burst disk, and same amount of gunpowder (6.639 grains for HF# 11, and 6.576 grains for HF# 39) were used, and the back pressure in the nitrogen test chamber was ~2300 psig. Despite keeping all these variables constant, the results from these two tests look quite different. For both tests, the first pressure peak shown in the P2111 trace within the breech is the firing of the initiator. The second peak and any subsequent peaks are from the combustion of the gunpowder. It should be noted that because the sensors are dynamic, the ~2300 psig baseline static pressure is not shown in the figures. For HF# 11, the burst disk clearly ruptured in a little over 0.1 ms from the time the initiator was fired. This is evident from the abrupt rise in pressure for P2112 followed by another abrupt rise in pressure for P2113. The sensors track the movement of the high pressure pulse through the pulse gun. For HF# 39, however, there was nearly 1 ms delay between the initiator firing and the burst disk rupturing. The only difference between these two tests was the way in which the gunpowder was packed within the breech. For HF# 11, the gunpowder was poured directly into the breech, atop the initiator, and held in place with a vegetable fiber wad appropriately sized for the barrel diameter. Once in place, the wad firmly held the gunpowder in place. For HF# 39, the gunpowder was rolled within cigarette paper with the ends of the paper twisted. The rolled gunpowder was gently pushed down into the breech, toward the initiator, and no wad was used. This method of loading the gunpowder consistently produced longer delays in the rupture of the burst disk, presumably because there was a steady, fuller burning of the gunpowder. The burst disk was rated for 8,000 psid, which means that the burst disk should not have opened until the pressure in the breech reached ~10,300 since there was ~2300 psig back pressure in the test chamber. In the case of HF# 11, the breech pressure only reached roughly 4200 psi before there was leakage either through or past the burst disk, but for HF#39, the breech pressure reached 10,600 psi prior to the burst disk opening. The temperature of the burst disk is certainly a factor in determining when the burst disk will rupture. A sharp rise in the burst disk temperature could weaken it and cause it to stray from the designed set point burst pressure. The burst disks are manufactured of Inconel to try to reduce their sensitivity to temperature, but how the burst disks perform above 900°F is not documented. All burst disks were engineered and tested by the manufacturer for ambient temperature conditions. One theory for why rolling the gunpowder in cigarette paper may produce better results is related to a more controlled temperature environment. The cigarette paper may act as a sheath that protects the burst disk from excessive temperatures during the rapid buildup of pressure in the breech. The ultimate benefit of not breeching the burst disk prematurely is shown in Figures 5 and 6, which graphs the resultant pressure pulse produced in the test chamber. For HF #11, the peak pressure on the P2123 trimmed adapter is about 270 psi, while for HF# 39 it is 343 psi, which is about 1.27 times greater in magnitude. In either case, the pressure pulse is ~20 μs in width once it reaches the test chamber. Another pressure rise about 100 μs later can be seen on the sensors located across from the pulse gun port, P2124 and P2121. These pressures are lower due to attenuation of the pressure wave as it moves across the test chamber. After the wave encounters the wall, it reflects back and forth within the chamber until it completely dissipates.

Pulse Gun↗

Behavior of Ullage Bubbles During Blowdown in Low-g Experiment (BUBBLE): Overview of a Cryogenic Tank Depressurization Test

Behavior of Ullage Bubbles during Blowdown in Low-g Experiment (BUBBLE) is a cryogenic tank depressurization drop tower experiment currently being designed at NASA Glenn Research Center. There is a need for liquid level rise data while venting a cryogenic propellant tank below the liquid saturation pressure in a reduced gravity environment. When a cryogenic tank is vented to a vapor pressure below the liquid saturation pressure, bubbles become entrained in the liquid causing the bulk liquid-vapor interface to rise. In reduced gravity, bubble rise velocity is diminished leading to a larger liquid level rise compared to a 1g environment. The purpose of the experiment is to gain further understanding of tank depressurization fluid physics and obtain high-fidelity data for model validation in 1g and reduced gravity environments. On-orbit cryogenic propellant tanks operating at high fill levels must efficiently manage venting operations to avoid the risk of liquid entrainment in the vent line, which could lead to asymmetric control thruster loads, freezing and clogging, and loss of liquid propellant. Validated models could be used to design settling and venting profiles to reduce risk and increase efficiency for cryogenic storage and transfer operations.

tank venting↗

X-Band Photonic Band-Gap Accelerator Structure Breakdown Experiment

In order to understand the performance of photonic band-gap (PBG) structures under realistic high gradient, high power, high repetition rate operation, a PBG accelerator structure was designed and tested at X band (11.424 GHz). The structure consisted of a single test cell with matching cells before and after the structure. The design followed principles previously established in testing a series of conventional pillbox structures. The PBG structure was tested at an accelerating gradient of 65 MV/m yielding a breakdown rate of two breakdowns per hour at 60 Hz. An accelerating gradient above 110 MV/m was demonstrated at a higher breakdown rate. Significant pulsed heating occurred on the surface of the inner rods of the PBG structure, with a temperature rise of 85 K estimated when operating in 100 ns pulses at a gradient of 100 MV/m and a surface magnetic field of 890 kA/m. A temperature rise of up to 250 K was estimated for some shots. The iris surfaces, the location of peak electric field, surprisingly had no damage, but the inner rods, the location of the peak magnetic fields and a large temperature rise, had significant damage. Breakdown in accelerator structures is generally understood in terms of electric field effects. These PBG structure results highlight the unexpected role of magnetic fields in breakdown. The hypothesis is presented that the moderate level electric field on the inner rods, about 14 MV/m, is enhanced at small tips and projections caused by pulsed heating, leading to breakdown. Future PBG structures should be built to minimize pulsed surface heating and temperature rise.

43 PARTICLE ACCELERATORS↗

The potential role of a carbon tax in U.S. fiscal reform

This paper examines fiscal reform options in the United States with an intertemporal computable general equilibrium model of the world economy called G-Cubed. Six policy scenarios explore two overarching issues: (1) the effects of a carbon tax under alternative assumptions about the use of the resulting revenue, and (2) the effects of alternative measures that could be used to reduce the budget deficit. We examine a simple excise tax on the carbon content of fossil fuels in the U.S. energy sector starting immediately at $15 per metric ton of carbon dioxide (CO2) and rising at 4 percent above inflation each year through 2050. We investigate policies that allow the revenue from the illustrative carbon tax to reduce the long run federal budget deficit or the marginal tax rates on labor and capital income. We also compare the carbon tax to other means of reducing the deficit by the same amount. We find that the carbon tax will raise considerable revenue: $80 billion at the outset, rising to $170 billion in 2030 and $310 billion by 2050. It also significantly reduces U.S. CO2 emissions by an amount that is largely independent of the use of the revenue. By 2050, annual CO2 emissions fall by 2.5 billion metric tons (BMT), or 34 percent, relative to baseline, and cumulative emissions fall by 40 BMT through 2050. The use of the revenue affects both broad economic impacts and the composition of GDP across consumption, investment and net exports. In most scenarios, the carbon tax lowers GDP slightly, reduces investment and exports, and increases imports. The effect on consumption varies across policies and can be positive if households receive the revenue as a lump sum transfer. Using the revenue for a capital tax cut, however, is significantly different than the other policies. In that case, investment booms, employment rises, consumption declines slightly, imports increase, and overall GDP rises significantly relative to baseline through about 2040. Thus, a tax reform that uses a carbon tax to reduce capital taxes would achieve two goals: reducing CO2 emissions significantly and expanding short-run employment and the economy. We examine three ways to reduce the deficit by an equal amount. We find that raising marginal tax rates on labor income has advantages over raising tax rates on capital income or establishing a carbon tax. A labor tax increase leaves GDP close to its baseline, reduces consumption very slightly and expands net exports slightly. Investment remains essentially unchanged. In contrast, a capital tax increase causes a significant and persistent drop in investment and much larger reductions in GDP. A carbon tax falls between the two: it lowers GDP more than a labor tax increase because it reduces investment. However, its effects on investment and GDP are more moderate than the capital tax increase, and it also significantly reduces CO2 emissions. A carbon tax thus offers a way to help reduce the deficit and improve the environment, and do so with minimal disturbance to overall economic activity.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Energy Efficiency's Role in Industrial Decarbonization

Around the world, efforts are increasing to drastically reduce greenhouse gas (GHG) emissions by 2050. The goal of the Paris Agreement is to hold the increase in global average temperature rise to below 2°C as compared with preindustrial levels, specifically aiming to limit it to 1.5°C. As of 2017, the global average temperature rise reached approximately 1°C. It is expected to hit the 1.5°C mark by 2040 if current trends continue. Limiting temperature rise to 2°C will require reaching net zero emissions in the latter half of the 21st century; GHG emissions would need to reach a near-zero value by 2050 to limit the rise to 1.5°C.

Sundaramoorthy, Senthil↗

Numerical study of groundwater flow cycling controlled by seawater/freshwater interaction in Woodville Karst Plain

Seawater intrusion due to sea level rise and climate change could significantly contaminate coastal groundwater resources, particularly in Florida, the flat low-land state in the United States. Based on the field investigation and hydrological measurements, a three-dimensional SEAWAT model is developed to evaluate the groundwater flow cycling and seawater intrusion to freshwater system in the Woodville Karst Plain (WKP), a typical karst groundwater system in the Floridan aquifer. The karst conduit network in the aquifer acts as fast flow pathway for groundwater flow and solute transport, so seawater could deeply intrude into the aquifer. Wakulla Spring, an inland spring 17 km from the coast and a coastal submarine spring, Spring Creek Spring Complex are connected through the conduit network. The flow direction between the two springs switches under various rainfall conditions in this region, thus the discharges at two karst springs are used to estimate the location of seawater/freshwater mixing interface. The SEAWAT modeling results indicate that the mixing interface, defined as 2 PSU (Practical Salinity Unit), intrudes 3 to 5 km through the subsurface karst conduit during the dry season and severely contaminates nearly 1 km width of groundwater around the conduit. The salinity distribution and the distance of seawater intrusion through the conduit system are very sensitive to precipitation variation and the sea level boundary condition. Furthermore, predictions are made for seawater intrusion to the aquifer under various sea level rise, precipitation scenarios and water pumping. The results show that the seawater intrusion could reach and contaminate inland freshwater systems if sea level rises 1.0 m or during a long-term no-precipitation season. Finally, this study provides insights for modeling and predicting the vulnerability of a coastal karst aquifer through the simulation of variable-density flow.

58 GEOSCIENCES↗

Insights from incorporating reference electrodes in symmetric lithium-ion cells with layered oxide or graphite electrodes

Symmetric cells provide complementary means to probe electrochemical processes in lithium-ion batteries. Here, positive and negative electrodes harvested from conventional oxide/graphite cells are cross-paired, and the assembled reference-electrode-bearing symmetric cells are cycled/aged. For graphite symmetric cells, the electrode potentials and impedances remain nearly constant during calendar aging and the parasitic currents are typically small. However, at higher cell voltages when the “positive” graphite potential exceeds 1.0 V vs. Li/Li + , the capacity loss is higher, indicating that even a mild (but prolonged) overdischarge can damage the SEI. For the layered-oxide symmetric cells there are strong parasitic currents and a persistent slide of the electrode potential over time during calendar aging. Significant cell impedance rise, especially at higher hold voltages, is also observed. Curiously, the impedance rise in the “negative” oxide electrode, which experiences potentials below 4.0 V vs. Li/Li + , is greater than in the “positive” oxide electrode that experiences much higher potentials. We postulate that electrolyte oxidation is responsible for the behavior of these oxide symmetric cells, as it supplies electrons (that bind more Li + into the cathode, causing the potential slide) and protons (that contribute to impedance rise). Furthermore, these insights can guide the development of future lithium-ion cell chemistries.

25 ENERGY STORAGE↗

Study on the Response Coefficient of Setback Structures Compared to Regular Moment Frame Structures

In design practice of many countries, seismic analysis and proportioning of structures are usually based upon linear elastic analysis due to reduced seismic forces by response coefficient; R. Setback structures are one of the most popular shapes of the constructed buildings. In setback structures, the shape and proportions of the building have a major effect on distribution of earthquake forces as they work their way through the building. On the other hand, geometric configuration has a profound effect on the structural-dynamic response of a building. Therefore, when a building has irregular features, such as asymmetric in height or vertical discontinuity, the traditional assumptions used in development of seismic criteria for regular buildings may not be applicable. Inelastic seismic behavior of these types of structures seems to be quite different from the regular steel moment resisting structures in which the overall ductility is localized at beam-ends.In order to investigate the seismic behavior and estimate the Response Coefficient of those structures, nonlinear static analysis (pushover) are used for three categories of setback structures namely low rise, medium rise and high rise buildings with different setbacks in their height. The Response Coefficient are calculated and compared with those taken from regular type of moment frame structures.

58 GEOSCIENCES↗

Time-resolved measurements on reflectivity of an ultrafast laser-induced plasma mirror

Using a linearly chirped laser pulse to irradiate antireflection coated targets, the time-varying reflectivity of a plasma mirror (PM) has been measured at various laser intensities from 10{sup 12} to 10{sup 17} W/cm{sup 2}. The onset of plasma generation as well as the formation process of a PM with the highest reflectivity has been observed. The rise time of the PM's reflectivity reaching up to the maximum varies from 300-500 fs at lower laser intensities but goes up to 900 fs at higher intensity of >10{sup 16} W/cm{sup 2}. This long rise time can be attributed to a slowly rising shoulder of the laser pulse, which will trigger the generation of preplasma well in advance of the laser peak. The detailed measurements on both time-integrated and time-resolved reflectivity of a PM, which is induced by p- and s-polarized laser pulses, respectively, indicate that an s-polarized pulse is favorable to obtain the maximal reflectivity and the best contrast improvement as well. This difference can be attributed to the weaker absorption and a smaller plasma scale length generated for s-polarization.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Ablation dynamics in coiled wire-array Z-pinches

Experiments to study the ablation dynamics of coiled wire arrays were performed on the MAGPIE generator (1 MA, 240 ns) at Imperial College, and on the COBRA generator at Cornell University's Laboratory of Plasma Studies (1 MA, 100 ns). The MAGPIE generator was used to drive coiled wires in an inverse array configuration to study the distribution of ablated plasma. Using interferometry to study the plasma distribution during the ablation phase, absolute quantitative measurements of electron line density demonstrated very high density contrasts between coiled ablation streams and inter-stream regions many millimetres from the wire. The measured density contrasts for a coiled array were many times greater than that observed for a conventional array with straight wires, indicating that a much greater axial modulation of the ablated plasma may be responsible for the unique implosion dynamics of coiled arrays. Experiments on the COBRA generator were used to study the complex redirection of plasma around a coiled wire that gives rise to the ablation structure exhibited by coiled arrays. Observations of this complex 3D plasma structure were used to validate the current model of coiled array ablation dynamics [Hall et al., Phys. Rev. Lett. 100, 065003 (2008)], demonstrating irrefutably that plasma flow from the wires behaves as predicted. Coiled wires were observed to ablate and implode in the same manner on both machines, indicating that current rise time should not be an issue for the scaling of coiled arrays to larger machines with fast current rise times.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

A comparison between spectra of runaway electron beams in SF{sub 6} and air

Runaway electron (RAE) with extremely high-energy plays important role on the avalanche propagation, streamer formation, and ionization waves in nanosecond-pulse discharges. In this paper, the generation of a supershort avalanche electron beam (SAEB) in SF{sub 6} and air in an inhomogeneous electric field is investigated. A VPG-30-200 generator with a pulse rise time of ∼1.6 ns and a full width at half maximum of 3–5 ns is used to produce RAE beams. The SAEBs in SF{sub 6} and air are measured by using aluminum foils with different thicknesses. Furthermore, the SAEB spectra in SF{sub 6} and air at pressures of 7.5 Torr, 75 Torr, and 750 Torr are compared. The results showed that amplitude of RAE beam current generated at the breakdown in SF{sub 6} was approximately an order of magnitude less than that in air. The energy of SAEB in air was not smaller than that in SF{sub 6} in nanosecond-pulse discharges under otherwise equal conditions. Moreover, the difference between the maximum energy of the electron distributions in air and SF{sub 6} decreased when the rise time of the voltage pulse increased. It was because the difference between the breakdown voltages in air and SF{sub 6} decreased when the rise time of the voltage pulse increased.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Pseudo-spark switch (PSS) characteristics under different operation conditions

The present paper concentrates on the characteristics of the pseudospark switch (PSS) designed in a previous work. The special characteristics of PSS make it a replacement for other high voltage switches such as thyratrons and ordinary high-pressure spark gaps. PSS is characterized by short rise time and small jitter time. The pseudo park chamber consists of two hollow cylindrical electrodes made of a stainless steel material (type 306L) separated by an insulator. The insulator used in our design is a glazed ceramic 70 mm in diameter and 3.5 mm in thickness. A PSS with an anode voltage of 29.2 kV, and a current of 3.6 kA and 11 ns rise time was achieved and used successfully at a repetition rate of about 2.2 kHz. A simple trigger circuit designed, built, and used effectively reaching more than 1.56 kV trigger pulse which is sufficient to ignite the argon gas inside the cathode to cause a breakdown. A non-inductive dummy load is designed to be a new technique to find the accurate value of the PSS inductance. A jitter time of ±10 ns pulses is observed to occur in a reliable manner for more than 6 h of continuous operation. In this research, the important parameters of this switch like rise time, peak current, and anode voltage were studied at various values of charging capacitance. The lifetime of this system is depending on the kind of the electrode material and on the type of insulation material in the main gap of the pseudospark switch.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Evolution of finite viscous disks with time-independent viscosity

We find Green functions for the accretion disk with fixed outer radius and time-independent viscosity. With the Green functions, a viscous evolution of the disk with any initial conditions can be described. Two types of inner boundary conditions are considered: the zero stress tensor and the zero accretion rate. The variable mass inflow at the outer radius can also be included. The well-known exponential decline of the accretion rate is a part of the solution with the inner zero stress tensor. The solution with the zero central accretion rate is applicable to disks around stars whose magnetosphere's boundary exceeds the corotation radius. Using the solution, the viscous evolution of disks in some binary systems can be studied. We apply the solution with zero inner stress tensor to outbursts of short-period X-ray transients during the time around the peak. It is found that for the Kramers’ regime of opacity and the initial surface density proportional to the radius, the rise time to the peak is t{sub rise}≈0.15 r{sub out}{sup 2}/ν{sub out} and the e-folding time of the decay is t{sub exp}≈0.45 r{sub out}{sup 2}/ν{sub out}. Comparison to non-stationary α-disks shows that both models with the same value of viscosity at the outer radius produce similar behavior on the viscous time-scale. For six bursts in X-ray novae, which exhibit fast-rise–exponential-decay and are fitted by the model, we find a way to restrict the turbulent parameter α.

79 ASTRONOMY AND ASTROPHYSICS↗

Simultaneous optimization of dose distributions and fractionation schemes in particle radiotherapy

Purpose: The paper considers the fractionation problem in intensity modulated proton therapy (IMPT). Conventionally, IMPT fields are optimized independently of the fractionation scheme. In this work, we discuss the simultaneous optimization of fractionation scheme and pencil beam intensities.Methods: This is performed by allowing for distinct pencil beam intensities in each fraction, which are optimized using objective and constraint functions based on biologically equivalent dose (BED). The paper presents a model that mimics an IMPT treatment with a single incident beam direction for which the optimal fractionation scheme can be determined despite the nonconvexity of the BED-based treatment planning problem.Results: For this model, it is shown that a small α/β ratio in the tumor gives rise to a hypofractionated treatment, whereas a large α/β ratio gives rise to hyperfractionation. It is further demonstrated that, for intermediate α/β ratios in the tumor, a nonuniform fractionation scheme emerges, in which it is optimal to deliver different dose distributions in subsequent fractions. The intuitive explanation for this phenomenon is as follows: By varying the dose distribution in the tumor between fractions, the same total BED can be achieved with a lower physical dose. If it is possible to achieve this dose variation in the tumor without varying the dose in the normal tissue (which would have an adverse effect), the reduction in physical dose may lead to a net reduction of the normal tissue BED. For proton therapy, this is indeed possible to some degree because the entrance dose is mostly independent of the range of the proton pencil beam.Conclusions: The paper provides conceptual insight into the interdependence of optimal fractionation schemes and the spatial optimization of dose distributions. It demonstrates the emergence of nonuniform fractionation schemes that arise from the standard BED model when IMPT fields and fractionation scheme are optimized simultaneously. Although the projected benefits are likely to be small, the approach may give rise to an improved therapeutic ratio for tumors treated with stereotactic techniques to high doses per fraction.

61 RADIATION PROTECTION AND DOSIMETRY↗

Characteristics of a Pulse-Periodic Corona Discharge in Atmospheric Air

Pulse-periodic corona discharge in atmospheric air excited by applying a voltage pulse with a subnanosecond or microsecond rise time to a point electrode is studied experimentally. It is shown that, at a voltage rise rate of dU/dt ~10{sup 14} V/s, positive and negative ball-shaped streamers with a front velocity of ≥2 mm/ns form near the point electrode. As dU/dt is reduced to 10{sup 10}−10{sup 11} V/s, the streamer shape changes and becomes close to cylindrical. The propagation velocity of cylindrical streamers is found to be ~0.1 mm/ns at dU/dt ~ 2 × 10{sup 10} V/s. It is shown that the propagation direction of a cylindrical streamer can be changed by tilting the point electrode, on the axis of which the electric field strength reaches its maximum value. It is established that, for the negative polarity of the point electrode and a microsecond rise time of the voltage pulse, a higher voltage is required to form a cylindrical streamer than for the positive polarity of the point electrode.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Rate-Dependent Aging Resulting from Fast Charging of Li-Ion Cells

The mass electrification of personal and service vehicles is reliant on the ability of battery packs to undergo extreme fast recharging. A central challenge is that the repeated exposure to high currents can trigger and/or accelerate mechanisms of performance degradation, such as lithium deposition, mechanical damage of active material particles, and impedance rise. Here, we investigate whether constraining high-rate charging to limited state-of-charge (SOC) ranges can mitigate these aging processes. Our experiments map the boundaries of lithium plating conditions, and also indicate that permanent losses of electrode capacity appear to be a function of cycle number, but not charging rate. Interestingly, we show that impedance rise appears to depend on charging rate alone, and not on the amount of charge passed at each cycle. This observation suggests that limiting fast charging to a narrow SOC range would only delay cell aging, but not fully prevent it from happening. We identify oxide-particle cracking as the likely mechanism for this impedance rise, suggesting that particle and electrode design are essential to enable fast charging. The findings of this work can inform the development of fast-charging protocols that are less damaging to cell health.

25 ENERGY STORAGE↗

Data-model files associated with the manuscript "Modeling the Effects of Wetland Restoration on Coastal Hydrology: A Case Study of Elkhorn Slough Watershed, California"

This package contains the data, simulation setups, notebooks and figures used in “Modeling the Effects of Wetland Restoration on Coastal Hydrology: A Case Study of Elkhorn Slough Watershed, California” (Xu et al., 2025). In this study, we selected Elkhorn Slough, a tidal estuary, in California, to investigate the impact of wetland restoration and sea level rise on coastal hydrology using the process-based coastal hydrologic model, Advanced Terrestrial Simulator (ATS), informed by site-specific data. We designed a novel modeling workflow for incorporating wetland restoration features into land cover and soil properties for the model parameterization. The validation results demonstrate a strong agreement between modeled and observed data. We studied the characteristics of coastal watershed hydrology, then focused on the surface water dynamics at two wetland sites within Elkhorn Slough, a reference site and a restored site. Our simulation results indicate that the restored site successfully maintains surface elevation, resulting in reduced surface inundation. We also examined the impact of wetland restoration under expected sea level rise over the next few decades. The low-lying Yampah Marsh, the reference site, is likely to be inundated due to future sea level rise when highest tides arrive; while a higher percentage of Hester Marsh, the restored site, would retain marsh vegetation in coming decades, regardless of tidal conditions. Our study provides important information for examining the outcome of restoration practices that include surface elevation in tidal wetlands under climate changes.Several files can be found from this data package.1. README.md: This file describes the title, journal, co-authors, abstract, repository structure and model version.2. Simulation_Setups.zip: The file contains the model configuration files (XML format) for ATS. 3. Notebooks.zip: The file contains the Jupyter notebooks for generating the pre- and post-restoration meshes and the meshes of future scenarios. 4. Figures.zip: The file contains the figures used in the manuscript.5. Data.zip: The file contains the data used to drive the model simulations, including watershed and wetlands boundaries, mesh files and references to additional datasets (e.g., meteorological forcing, tidal dataset, DEMs, land cover, soil properties). Also, it contains water level observations at the restored wetland.

54 ENVIRONMENTAL SCIENCES↗

Single-Mode VISAR

High energy-density physics (HEDP) experiments examine the properties of materials under extreme conditions. These experiments rely on the measurement of one or two velocities. These velocities are used to obtain Hugoniot relationships and thermodynamic equations of state. This methodology is referred to as 'velocimetry' and an instrument used to measure the shock wave is called a 'velocimeter' or a '(velocity) diagnostic'. The two most-widely used existing velocity diagnostics are; photonic Doppler velocimetry (PDV) and velocity interferometer system for any reflector (VISAR). PDV's advantages are a fast rise-time and ease of implementation but PDV has an upper velocity limit. Traditional implementations of VISAR have a rise time 10 times slower than PDV and are not easily implemented but are capable of measuring any velocity produced during HEDP experiments. This thesis describes a novel method of combining the positive attributes of PDV and VISAR into a more cost effective diagnostic called a Single-Mode VISAR (SMV). The new diagnostic will consist of PDV parts in a VISAR configuration. This configuration will enable the measurement of any velocity produced during shock physics experiments while the components used to build the diagnostic will give the diagnostic a fast rise time and make it easy to use. This thesis describes the process of building and testing the first single-mode VISAR. The tests include verifying the performance of the components and the diagnostic as a whole.

42 ENGINEERING↗