Search NASA⌕ Search

SEARCH · Search NASA

Results for “SIZE DISTRIBUTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60

Holistic Interactions of Shallow Clouds, Aerosols, and Land-Ecosystems (HI-SCALE) Field Campaign Report

Cumulus convection is an important component in the atmospheric radiation budget and hydrologic cycle over the southern Great Plains and over many regions of the world, particularly during the summertime growing season when intense turbulence induced by surface radiation couples the land surface to clouds. Current convective cloud parameterizations contain uncertainties resulting in part from insufficient coincident data that couples cloud macrophysical and microphysical properties to inhomogeneities in land surface, boundary layer, and aerosol properties. The Holistic Interactions of Shallow Clouds, Aerosols, and Land-Ecosystems (HI-SCALE) campaign was designed to provide a detailed set of measurements that are needed to obtain a more complete understanding of the lifecycle of shallow clouds by coupling cloud macrophysical and microphysical properties to land surface properties, ecosystems, and aerosols. Some of the land-atmosphere-cloud interactions that can be studied using HI-SCALE data are shown in Figure 1. HI-SCALE consisted of two 4-week intensive operation periods (IOPs), one in the spring (April 24-May 21) and the other in the late summer (August 28-September 24) of 2016, to take advantage of different stages of the plant lifecycle, the distribution of “greenness” for various types of vegetation in the vicinity of the U.S. Department of Energy (DOE) Atmospheric Radiation Measurement (ARM) Climate Research Facility Southern Great Plains (SGP) site, and aerosol properties that vary during the growing season. As expected, satellite measurements indicated that the Normalized Difference Vegetation Index (NDVI) was much “greener” in the vicinity of the SGP site during the spring IOP than the late summer IOP as a result of winter wheat maturing in the spring and being harvested in the early summer. As shown in Figure 2, temperatures were cooler than average and soil moisture was high during the spring IOP, while temperatures were warmer than average and soil moisture was low during the late summer IOP. These factors likely influence the occurrence and lifecycle of shallow clouds. Most of the instrumentation was deployed on the ARM Aerial Facility (AAF) Gulfstream 1 (G-1) aircraft, including those that measure atmospheric turbulence, cloud water content and drop size distributions, aerosol precursor gases, aerosol chemical composition and size distributions, and cloud condensation nuclei (CCN) concentrations. The specific instrumentation is listed in Table 1. The team of scientists participating in the G-1 flights were from Pacific Northwest National Laboratory (PNNL), Brookhaven National Laboratory (BNL), and the University of Washington. Routine ARM aerosol measurements made at the surface were supplemented with aerosol microphysical properties measurements, with support from the DOE Environmental Molecular Sciences Laboratory (EMSL) User Facility and the Atmospheric System Radiation (ASR) program. This included deploying a scanning mobility particle sizer (SMPS) to measure aerosol size distribution, a proton transfer reaction-mass spectrometer (PTR-MS) to measure volatile organic compounds, an aerosol mass spectrometer (AMS) to measure bulk aerosol composition, and the single-particle laser ablation time-of-flight mass spectrometer (SPLAT II) to measure single-particle aerosol composition at the SGP site Guest Instrumentation Facility. In this way, characterization of aerosol properties at the surface and on the G-1 were consistent. In addition, the HI-SCALE: Nanoparticle Composition and Precursors add-on campaign was conducted during the second IOP in which several state-of-the-science chemical ionization mass spectrometers were deployed to measure nanoparticle composition and precursors. Scientists participating in the surface measurements were from PNNL, BNL, University California–Irvine, Augsberg College, Colorado University, Aerodyne Inc., and Aerosol Dynamics Inc.

54 ENVIRONMENTAL SCIENCES↗

A Pure Marine Aerosol Model, for Use in Remote Sensing Applications

Retrievals of aerosol optical depth (AOD) and related parameters from satellite measurements typically involve prescribed models of aerosol size and composition, and are therefore dependent on how well these models are able to represent the radiative behaviour of real aerosols, This study uses aerosol volume size distributions retrieved from Sun-photometer measurements at 11 Aerosol Robotic Network (AERONET) island sites, spread throughout the world's oceans, as a basis to define such a model for unpolluted maritime aerosols. Size distributions are observed to be bimodal and approximately lognormal, although the coarse mode is skewed with a long tail on the low-radius end, The relationship of AOD and size distribution parameters to meteorological conditions is also examined, As wind speed increases, so do coarse-mode volume and radius, The AOD and Angstrom exponent (alpha) show linear relationships with wind speed, although there is considerable scatter in all these relationships, limiting their predictive power. Links between aerosol properties and near-surface relative humidity, columnar water vapor, and sea surface temperature are also explored. A recommended bimodal maritime model, which is able to reconstruct the AERONET AOD with accuracy of order 0.01-0.02, is presented for use in aerosol remote sensing applications. This accuracy holds at most sites and for wavelengths between 340 nm and 1020 nm. Calculated lidar ratios are also provided, and differ significantly from those currently used in Cloud-Aerosol Lidar with Orthogonal Polarization (CALIOP) processing.

Sayer, A. M.↗

Analytical model of brittle destruction based on hypothesis of scale similarity

The size distribution of dust particles in thermonuclear (fusion) devices is closely described by a power law, which may be related to the brittle destruction of materials. The hypothesis of scale similarity leads to the conclusion that the size distribution of particles formed as a result of a brittle destruction is described by a power law with the exponent -{alpha} that can range from -4 to -1. The model of brittle destruction is described in terms of the fractal geometry, and the distribution exponent is expressed via the fractal dimension of packing. Under additional assumptions, it is possible to refine the {alpha} value and, vice versa, to determine the type of destruction using the measured size distribution of particles.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Statistical Models of Areal Distribution of Fragmented Land Cover Types

Imagery of coarse resolution, such weather satellite imagery with 1 square kilometer pixels, is increasingly used to monitor dynamic and fragmented types of land surface types, such as scars from recent fires and ponds in wetlands. Accurate estimates of these land cover types at regional to global scales are required to assess the roles of fires and wetlands in global warming, yet difficult to compute when much of the area is accounted for by fragments about the same size as the pixels. In previous research, we found that size distribution of the fragments in several example scenes fit simple two-parameter models and related effects of coarse resolution to errors in area estimates based on pixel counts. We summarize our model based approach to improved area estimations and report on progress to develop accurate areas estimates based on modeling the size distribution of the fragments, including analysis of size distributions on an expanded set of maps developed from digital imagery.

Hlavka, C.↗

Process and feedstock driven microstructure for laser powder bed fusion of 316L stainless steel

Here in the pursuit of improving additively manufactured (AM) component quality and reliability, fine-tuning critical process parameters such as laser power and scan speed is a great first step toward limiting defect formation and optimizing the microstructure. However, the synergistic effects between these process parameters, layer thickness, and feedstock attributes (e.g. powder size distribution) on part characteristics such as microstructure, density, hardness, and surface roughness are not as well-studied. In this work, we investigate 316L stainless steel density cubes built via laser powder bed fusion (L-PBF), emphasizing the significant microstructural changes that occur due to altering the volumetric energy density (VED) via laser power, scan speed, and layer thickness changes, coupled with different starting powder size distributions. This study demonstrates that there is not one ideal process set and powder size distribution for each machine. Instead, there are several combinations or feedstock/process parameter ‘recipes’ to achieve similar goals. This study also establishes that for equivalent VEDs, changing powder size can significantly alter part density, GND density, and hardness. Through proper parameter and feedstock control, part attributes such as density, grain size, texture, dislocation density, hardness, and surface roughness can be customized, thereby creating multiple high-performance regions in the AM process space.

316L stainless steel↗

In situ TEM investigation into the thermal stability of nanograined FCC metals.

Nanostructured materials often display very unique properties related to their far-from-equilibrium nature. Due to these unique structures, many of these materials transform into other, more stable microstructures with minimal thermal excitation. This work will highlight examples of the unexpected routes taken during the microstructural evolution of pulsed-laser deposited (PLD) free-standing face-centered cubic (FCC) thin films as a function of deposition condition and annealing temperatures. A direct comparison between the grain growth dynamics observed during in situ TEM annealing experiments in PLD films of high-purity aluminum, copper, gold and nickel films, as well as aluminum-alumina alloys shows a multitude of kinetics. For high-purity systems film thickness, void density, grain size distribution, and deposition temperature were found to be the primary factors observed controlling the rate, extent, and nature of the grain growth. The growth dynamics ranged from nearly classical normal grain growth to abnormal grain growth resulting in a bimodal grain size distribution. The grain growth rate was found to be highly dependent on the materials system despite all of the films being nanograined FCC metals produced by similar PLD parameters. The investigation of the aluminum-alumina alloys produced under various compositions and deposition parameters suggests that particle pinning can be used to maintain nanostructured films, even after annealing treatments at high homologous temperatures. In addition to investigating the grain growth dynamics and the resulting grain size distribution, the variety of internal microstructures formed from thermal annealing were evaluated. These structures ranged from intergranular voids to stacking-fault tetrahedra. An unexpected, metastable hexagonal-closed packed phase was indentified in the high-purity nickel films. These in situ TEM observations have provided key insight into the microstructural evolution of nanograined free-standing metal films and the defect structure present in the grains resulting from various growth dynamics, in addition to suggesting multiple methods to tailor the structure and the resulting properties of nanostructured free-standing films.

36 MATERIALS SCIENCE↗

Observations of aerosol optical depth during the First ISLSCP Field Experiment (FIFE)

Solar radiation measurements were made with a multiwavelength airborne tracking sunphotometer during the First International Satellite Land Surface Climatology Project Field Experiment (FIFE). Data from June 6, and October 11, 1987 are analyzed. Atmospheric optical properties were derived from the data, including total optical depth, aerosol optical depth, aerosol size distribution, aerosol phase function, and aerosol single scattering albedo. The aerosol optical depths for June 6 exhibited a spectral dependence that peaked at short wavelengths, whereas those for October 11 decreased monotonically with wavelength and closely followed an Angstrom wavelength dependence. Also, a unimodal aerosol size distribution was found for the June 6 data, while the October 11 data exhibited a power law size distribution. It is suggested that these differences indicate the need for simultaneous sunphotometer measurements and remotely sensed data.

Spanner, Michael A.↗

Quantification of Powder Spreading Process for Metal Additive Manufacturing

In powder bed additive manufacturing (AM), the powder spreading process can lead to inhomogeneity in layer height, porosity level, and particle size distribution. Hence, creating homogeneous layers is the first task for optimal printing. The conventional assessment methods for powder quality are limited to a measurement of powder morphology, flowability, particle size distribution, surface roughness, and packing density. However, those techniques may not be the most appropriate to quantify the powder bed characteristics since it is not able to capture local particle configuration and does not provide any vectoral information (e.g., arrangement of contacts between particles during spreading). In this project, we: 1) developed a powder spreading model using discrete element method (DEM) for multiple-layered process, 2) experimentally measure powder spreading dynamics including static angle of repose (AOR) and dynamic AOR in order to calibrate and subsequently validate the model, and 3) investigated the effect of particle spreading process parameters on spatial powder bed structure and quality using scalar (e.g., porosity, surface roughness, coordination number, and particle size distribution) and tensorial (e.g., directionality of inter-particle contacts) methods for a comprehensive quantification of powder bed.

36 MATERIALS SCIENCE↗

Impacts of Mid-level Biofuel Content in Gasoline on SIDI Engine-Out and Tailpipe Particulate Matter Emissions: Preprint

The influences of ethanol and iso-butanol blended with gasoline on engine-out and post Three-Way Catalyst (TWC) particle size distribution and number concentration were studied using a GM 2.0L turbocharged Spark Ignition Direct Injection (SIDI) engine. The engine was operated using the production ECU with a dynamometer controlling the engine speed and the accelerator pedal position controllingthe engine load. A TSI Fast Mobility Particle Sizer (FMPS) spectrometer was used to measure the particle size distribution in the range from 5.6 to 560 nm with a sampling rate of 1 Hz. US federal certification gasoline (E0), two ethanol-blended fuels (E10 and E20), and 11.7% iso-butanol blended fuel (BU12) were tested. Measurements were conducted at ten selected steady-state engine operationconditions. Bi-modal particle size distributions were observed for all operating conditions with peak values at particle sizes of 10 nm and 70 nm. Idle and low speed / low load conditions emitted higher total particle numbers than other operating conditions. At idle, the engine-out Particulate Matter (PM) emissions were dominated by nucleation mode particles, and the production TWC reduced thesenucleation mode particles by more than 50%, while leaving the accumulation mode particle distribution unchanged. At engine load higher than 6 bar NMEP, accumulation mode particles dominated the engine-out particle emissions and the TWC had little effect. Compared to the baseline gasoline (E0), E10 does not significantly change PM emissions, while E20 and BU12 both reduce PM emissions under theconditions studied. Iso-butanol was observed to impact PM emissions more than ethanol, with up to 50% reductions at some conditions. In this paper, the issues related to PM measurement using FMPS are also discussed. While some uncertainties are due to engine variation, the FMPS must be operated under careful maintenance procedures in order to achieve repeatable measurement results.

02 PETROLEUM↗

Airborne Sunphotometry of African Dust and Marine Boundary Layer Aerosols in PRIDE

The Puerto Rico Dust Experiment (PRIDE) was conducted during summer 2000 to study the radiative, microphysical and transport properties of Saharan dust in the Caribbean region. During PRIDE, NASA Ames Research Center's six-channel airborne autotracking sunphotometer (AATS-6) was operated aboard a Piper Navajo airplane based at Roosevelt Roads Naval Station on the northeast coast of Puerto Rico. AATS-6 measurements were taken during 21 science flights off the coast of Puerto Rico in the western Caribbean. Data were acquired within and above the Marine Boundary Layer (MBL) and the Saharan Aerosol Layer (SAL) up to 5.5 km altitude tinder a wide range of dust loadings. Aerosol optical depth (AOD) spectra and columnar water vapor (CWV) values have been calculated from the AATS-6 measurements by using sunphotometer calibration data obtained at Mauna Loa Observatory (3A kin ASL) before (May) and after (October) PRIDE. Mid-visible AOD values measured near the surface during PRIDE ranged from 0.07 on the cleanest day to 0.55 on the most turbid day. Values measured above the MBL were as high as 0.35; values above the SAL were as low as 0.01. The fraction of total column AOD due to Saharan dust cannot be determined precisely from AATS-6 AOD data alone due to the uncertainty in the extent of vertical mixing of the dust down through the MBL. However, analyses of ground-based and airborne in-situ aerosol sampling measurements and ground-based aerosol lidar backscatter data should yield accurate characterization of the vertical mixing that will enable calculation of the Saharan dust AOD component from the sunphotometer data. Examples will be presented showing measured AATS-6 AOD spectra, calculated aerosol extinction and water vapor density vertical profiles, and aerosol size distributions retrieved by inversion of the AOD spectra. Near sea-surface AOD spectra acquired by AATS-6 during horizontal flight legs at 30 m ASL are available for validation of AOD derived from coincident satellite sensor (TOMS, MODIS, MISR) measurements. AATS-6 AOD data acquired during numerous aircraft ascents and descents through the MBL and the SAL should permit atmospheric column closure analyses with respect to aerosol optical depth, extinction, and size distribution by comparison with coincident aircraft-based in-situ particle size distribution measurements and ground-based (Cabras Island, Puerto Rico) micropulse lidar aerosol backscatter measurements. The aerosol information derived from the column closure analyses can be used subsequently to calculate radiative flux changes, which can then be compared with coincident spectral flux measurements taken from aboard the aircraft with a solar spectral flux radiometer.

Livingston, John M.↗

Aerosol-Cloud Interactions during Tropical Deep Convection: Evidence for the Importance of Free Tropospheric Aerosols

NASA's 2002 CRYSTAL-FACE field experiment focused on the formation and evolution of tropical cirrus cloud systems in southern Florida. Multiple aircraft extensively sampled cumulonimbus dynamical and microphysical properties, as well as characterizing ambient aerosol populations both inside and outside the full depth of the convective column. On July 18, unique measurements were taken when a powerful updraft was traversed directly by aircraft, providing a window into the primary source region of cumulonimbus anvil crystals. Observations of the updraft, entered at approximately l0 km altitude and -34 C, indicated more than 200 cloud particles per mL at vertical velocities exceeding 20 m/s and the presence of significant condensation nuclei and liquid water within the core. In this work, aerosol and cloud phase observations are integrated by simulating the updraft conditions using a large-eddy resolving model with 3 explicit multiphase microphysics, including treatment of size-resolved aerosol fields, aerosol activation and freezing, and evaporation of cloud particles back to the aerosol phase. Simulations were initialized with observed thermodynamic and aerosol size distributions profiles and convection was driven by surface fluxes assimilated from the ARPS forecast model. Model results are consistent with the conclusions that most crystals are homogeneously frozen droplets and that entrained free tropospheric aerosols may contribute a significant fraction of the crystals. Thus most anvil crystals appear to be formed aloft in updraft cores, well above cloud base. These conclusions are supported by observations of hydrometeor size distribution made while traversing the dore, as well as aerosol and cloud particle size distributions generally observed by aircraft below 4km and crystal properties generally observed by aircraft above 12km.

Ackerman, A.↗

Models of lipid droplets growth and fission in adipocyte cells

Lipid droplets (LD) are spherical cellular inclusion devoted to lipids storage. It is well known that excessive accumulation of lipids leads to several human worldwide diseases like obesity, type 2 diabetes, hepatic steatosis and atherosclerosis. LDs' size range from fraction to one hundred of micrometers in adipocytes and is related to the lipid content, but their growth is still a puzzling question. It has been suggested that LDs can grow in size due to the fusion process by which a larger LD is obtained by the merging of two smaller LDs, but these events seems to be rare and difficult to be observed. Many other processes are thought to be involved in the number and growth of LDs, like the de novo formation and the growth through additional neutral lipid deposition in pre-existing droplets. Moreover the number and size of LDs are influenced by the catabolism and the absorption or interaction with other organelles. The comprehension of these processes could help in the confinement of the pathologies related to lipid accumulation. In this study the LDs' size distribution, number and the total volume of immature (n=12), mature (n=12, 10-days differentiated) and lipolytic (n=12) 3T3-L1 adipocytes were considered. More than 11,000 LDs were measured in the 36 cells after Oil Red O staining. In a previous work Monte Carlo simulations were used to mimic the fusion process alone between LDs. We found that, considering the fusion as the only process acting on the LDs, the size distribution in mature adipocytes can be obtained with numerical simulation starting from the size distribution in immature cells provided a very high rate of fusion events. In this paper Monte Carlo simulations were developed to mimic the interaction between LDs taking into account many other processes in addition to fusion (de novo formation and the growth through additional neutral lipid deposition in pre-existing droplets) in order to reproduce the LDs growth and we also simulated the catabolism (fission and the decrease through neutral lipid exit from pre-existing droplets) to reproduce their size reduction observed in lipolytic conditions. The results suggest that each single process, considered alone, can not be considered the only responsible for the size variation observed, but more than one of them, playing together, can quite well reproduce the experimental data. - Highlights: The growth and fission of the lipid droplets (LDs) were computationally simulated. To write and test the growth and fission models more than 110,000 LDs were measured. The usual processes considered alone, are not able to justify the experimental data. Some processes, playing together, can explain the growth and fission.

60 APPLIED LIFE SCIENCES↗

Determination of cosmic bodies size-velocity distribution by observation of current impacts on Mars

Collisions of cosmic bodies with terrestrial planets involve many physical processes such as deceleration and ablation during their flight through an atmosphere, the impact at a surface accompanied by cratering, melting and evaporation of surface material, generation of shock waves, etc. If body velocity is high enough then a thermal radiation is very important. All these processes on Mars proceed differently than on the other planets because of the low density of its atmosphere. In particular, this leads to the fact that smaller bodies of sizes of the order of 0.1-10 m strike the planet surface without being decelerated and perform some effects which may be detected by equipment placed on a board of artificial satellites, by a network of stations at the surface of Mars and even from the Earth. These observations can be used to determine size-velocity distribution of such bodies in the Solar System. Numerical simulation of the impacts at the surface of Mars have been carried out using two-dimensional gas dynamic code with detailed consideration of the thermal radiative transfer. This work is an extension of our previous paper. We have expanded a range of projectile sizes up to r sub 0 = 100 m. For such a large-scale body, the initial stage of the impact, involving crate ring and ejection of surface material, is very important. Thus, these effects have been taken into account.

Nemchinov, I. V.↗

A standard particle sizer-velocimeter

A standard particle sizer-cum-velocimeter is described, which was designed and built for the purpose of providing a standard source of aerosols of known size-distribution, moving with a known velocity, for the purpose of calibrating the continuous wave (CW) CO2-Laser Doppler Velocimeters at Marshall Space Flight Center. The instrument is designed with the capabilities of: (1) monitoring the size-distribution of particles of diameters larger than 1.0 microns; (2) measuring flow velocities in the range 0.05 - 100.0 cm/sec; (3) photographing particles of diameters above 0.2 microns moving at slow speeds (approximately 0.1 cm/sec); (4) measuring the size-distribution of particles settling in quiet air (or convection velocities of less than 0.15 cm/sec); and (5) use in the laboratory or in the field.

Deepak, A.↗

Physical and chemical comparison of soot in hydrocarbon and biodiesel fuel diffusion flames: A study of model and commercial fuels

Data are presented to compare soot formation in both surrogate and practical fatty acid methyl ester biodiesel and petroleum fuel diffusion flames. The approach here uses differential mobility analysis to follow the size distributions and electrical charge of soot particles as they evolve in the flame, and laser ablation particle mass spectrometry to elucidate their composition. Qualitatively, these soot properties exhibit a remarkably similar development along the flames. The size distributions begin as a single mode of precursor nanoparticles, evolve through a bimodal phase marking the onset of aggregate formation, and end in a self preserving mode of fractal-like particles. Both biodiesel and hydrocarbon fuels yield a common soot composition dominated by C{sub x}H{sub y}{sup +} ions, stabilomer PAHs, and fullerenes in the positive ion mass spectrum, and C{sub x}{sup -} and C{sub 2x}H{sup -} in the negative ion spectrum. These ion intensities initially grow with height in the diffusion flames, but then decline during later stages, consistent with soot carbonization. There are important quantitative differences between fuels. The surrogate biodiesel fuel methyl butanoate substantially reduces soot levels, but soot formation and evolution in this flame are delayed relative to both soy and petroleum fuels. In contrast, soots from soy and hexadecane flames exhibit nearly quantitative agreement in their size distribution and composition profiles with height, suggesting similar soot precursor chemistry. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effect of rapid thermal annealing temperature on the dispersion of Si nanocrystals in SiO{sub 2} matrix

Effect of rapid thermal annealing temperature on the dispersion of silicon nanocrystals (Si-NC’s) embedded in SiO{sub 2} matrix grown by atom beam sputtering (ABS) method is reported. The dispersion of Si NCs in SiO{sub 2} is an important issue to fabricate high efficiency devices based on Si-NC’s. The transmission electron microscopy studies reveal that the precipitation of excess silicon is almost uniform and the particles grow in almost uniform size upto 850 °C. The size distribution of the particles broadens and becomes bimodal as the temperature is increased to 950 °C. This suggests that by controlling the annealing temperature, the dispersion of Si-NC’s can be controlled. The results are supported by selected area diffraction (SAED) studies and micro photoluminescence (PL) spectroscopy. The discussion of effect of particle size distribution on PL spectrum is presented based on tight binding approximation (TBA) method using Gaussian and log-normal distribution of particles. The study suggests that the dispersion and consequently emission energy varies as a function of particle size distribution and that can be controlled by annealing parameters.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Microstructural Evaluations of Baseline HSR/EPM Disk Alloys

Six alloys representing two classes of powder metallurgy nickel-based superalloys were examined by transmission electron microscopy (TEM) and phase extraction. Alloys KM4, CH98, IN-100 and 456 are based on a Ni-18Co-12Cr composition while alloys Rene' 88 DT and SR 3 have lower Al and Co and higher Cr contents. The lambda size distributions were determined from quantitative image analysis of the TEM images. The volume fraction of lambda and carbides and the composition of the phases were determined by a combination of phase extraction and TEM. The results showed many similarities in lambda size distributions, grain boundary serrations, and grain boundary carbide frequencies between alloys KM4, CH98, 456, Rene' 88 DT and SR 3 when heat treated to give an approximate grain size of ASTM 6. The density of grain boundary carbides in KM4 was shown to substantially increase as the grain size increased. IN-100 and 456 subjected to a serration cooling heat treatment had much more complex lambda size distributions with very large intergranular and intragranular secondary lambda as well as finer than average cooling and aging lambda. The grain boundary carbides in IN-100 were similar to the other alloys, but 456 given the serration cooling heat treatment had a more variable density of grain boundary carbides. Examination of the phases extracted from the matrix showed that there were significant differences in the phase chemistries and elemental partitioning ratios between the various alloys.

Gabb, Timothy P.↗