Search NASA⌕ Search

SEARCH · Search NASA

Results for “Time Calibration”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60

Energy, frequency, and distance of moonquakes at the Apollo 17 site

'Thermal' moonquakes have been detected at the Apollo 17 site. A typical event releases about 1 to 10 million ergs of energy. The annual seismic energy release for the events observed in the Taurus-Littrow Valley is estimated at 100 billion ergs. Such small events would not cause impossibly rapid erosion on either the North Massif or within the craters of the Central Cluster. Seismic events become increasingly frequent after sunrise and reach a maximum at sunset. The largest events, however, occur most commonly near lunar noon. Rise times of the seismic signals, after being calibrated by the well-located Lunar Seismic Profiling Experiment (LSPE) seismic sources, were used to estimate distances to the seismic events. Most seismic events (about 90%) appear to occur within 2.5 km of the seismometer array.

Cooper, M. R.↗

Calibration validation for the GEOS-3 altimeter

The absolute bias calibration for the GEOS-3 intensive mode altimeter was measured using two satellite passes whose groundtracks were within 1 km of the Bermuda laser station. The Bermuda laser tracked on the two passes, and was supported by two other NASA lasers on one pass and by the NASA Spacecraft Tracking and Data Network on the other pass. For each pass, the altimeter data around Bermuda was smoothed and extrapolated to the point closest to overhead at the laser site. After correcting for tide heights and sea state effects, the two passes give calibration biases which are in agreement to within 26 cm and have a weighted mean of -5.69 + or - 0.16m for correcting altimeter measurements to the center-of-mass of the spacecraft (i.e., including the antenna tracking point correction). It was found impossible to reconcile the two calibration passes, as well as a set of altimeter crossovers in the middle of the GEOS-3 calibration area, without allowing for a data time tag error. On the bias of a selected set of four crossovers, and an assessment of probable sources of timing error, it was concluded that one interpulse period (10.24 msec) should be added to the data time tags.

Martin, C. F.↗

Correlated Birkeland current signatures from the TRIAD and Magsat magnetic field data

Transverse magnetic disturbances associated with Birkeland currents have been measured by the Magsat and TRIAD spacecraft, whose orbits were nearly coplanar from November to mid-December, 1979. A comparison of data received when the satellites were over the TRIAD/Chatanika receiving station shows that 75% of magnetic disturbance measurements are similar in shape and magnitude, with TRIAD peak disturbances being on average 7% larger than those of Magsat. This discrepancy is lower than measurement uncertainties due to baselines and calibration. During periods of higher Kp, despite time separations of as much as 45 min, better agreement is found in the large-scale and well-defined field-aligned current signatures.

Zanetti, L. J.↗

Calibrated Ancillary System (CAS) user's guide, volume 5

The Calibrated Ancillary System (CAS) provides real-time parameters from the orbiter downlink (ancillary data) to the Goddard Space Flight Center (GSFC). This user's guide contains the introduction to the equipment, operation, general procedures, and specific procedures of CAS. Volume 5 describes the testing user mission planning procedures including the bulletin board system and ancillary products procedures. Instructions for viewing the SDT/TDT (shuttle data tape/telemetry descriptor tape) data base and the file management menu are also given.

Source record↗

Hardware fault insertion and instrumentation system: Mechanization and validation

Automated test capability for extensive low-level hardware fault insertion testing is developed. The test capability is used to calibrate fault detection coverage and associated latency times as relevant to projecting overall system reliability. Described are modifications made to the NASA Ames Reconfigurable Flight Control System (RDFCS) Facility to fully automate the total test loop involving the Draper Laboratories' Fault Injector Unit. The automated capability provided included the application of sequences of simulated low-level hardware faults, the precise measurement of fault latency times, the identification of fault symptoms, and bulk storage of test case results. A PDP-11/60 served as a test coordinator, and a PDP-11/04 as an instrumentation device. The fault injector was controlled by applications test software in the PDP-11/60, rather than by manual commands from a terminal keyboard. The time base was especially developed for this application to use a variety of signal sources in the system simulator.

Benson, J. W.↗

Characterization of the Nimbus-7 SBUV radiometer for the long-term monitoring of stratospheric ozone

Precise knowledge of in-orbit sensitivity change is critical for the successful monitoring of stratospheric ozone by satellite-based remote sensors. This paper evaluates those aspects of the in-flight operation that influence the long-term stability of the upper stratospheric ozone measurements made by the Nimbus-7 SBUV spectroradiometer and chronicles methods used to maintain the long-term albedo calibration of this UV sensor. It is shown that the instrument's calibration for the ozone measurement, the albedo calibration, has been maintained over the first 6 yr of operation to an accuracy of approximately + or - 2 percent. The instrument's wavelength calibration is shown to drift linearly with time. The knowledge of the SBUV wavelength assignment is maintained to a 0.02-nm precision.

Cebula, Richard P.↗

Dynamics Explorer guest investigator

The research has focused on using the SAI auroral images as a high resolution auroral precipitation input to the USU global scale ionospheric model. From the global scale modeling viewpoint, these images offer unique spatial and temporal resolution since all prior studies have used empirical auroral models. These latter models are devoid of storm, substorm, or discrete oval features. The research focused on the problems in converting images to energy flux; using LAPU data to calibrate these energy fluxes; using the USU Time Dependent Ionospheric Model (TDIM) to look at the ionospheric consequences of this structure; and then using DE-2 in-situ observations to compare with the TDIM ionospheric parameters. In carrying out these studies, several additional investigations cropped up which were pursued to help meet the overall goals. The foremost difficulty in carrying out the TDIM modeling in conjunction with the high resolution DE auroral model was that of defining an appropriate ionospheric convection pattern. Under northward conditions this pattern is very complex. In order to study Theta aurora or in general northward IMF conditions, a new model was required. Hence, a study was completed to supply this new model to drive the TDIM as a function of the IMF. With the DE auroral model having adequate resolution to show structure on the 100's of km and all model electric fields being devoid of such structure, an investigation was pursued to find out the effects of structures in the electric field on the F-region.

Sojka, J. J.↗

The size and shape of (2) Pallas from the 1983 occultation of 1 Vulpeculae

The analysis and results of an occultation of the spectroscopic binary star 1 Vulpeculae by the asteroid (2) Pallas, observed from 130 locations, are presented. Combination of solutions from this and previous occultations shows the triaxial shape of Pallas to be elongated, but not severely, with the ratio of the largest to the smallest axes being less than 1.15. The data provide a separation and a position angle of the secondary component of 1 Vulpeculae and indicate that the star's actual parallax is probably near 0.008 arcsec, half of the published value. The analysis gives a calibration of the accuracy and the reaction time corrections for visual observations of asteroidal occultations. The absence of any confirmed secondary extinctions shows that any satellites of Pallas must be rare or small. The photometric observations seem to rule out a substantial cloud of dust surrounding Pallas postulated previously.

Dunham, David W.↗

Three dimensional vision - Requirements and applications in a space environment

Various approaches to three-dimensional vision in space are reviewed with emphasis on the redundant 3D vision system designed for the Center for Intelligent Robotic Systems for Space Exploration. The system uses a controllable subset of five cameras, programmable structured light patterns, and sophisticated calibration routines. The design emphasizes real-time operation, human supervisory intervention, and the use of 3D vision to enhance the performance of cooperating robotic arms. Two methods of estimating the location of a point using 3D vision are discussed.

Noseworthy, J. R.↗

Nimbus-7 Earth radiation budget calibration history. Part 2: The Earth flux channels

Nine years (November 1978 to October 1987) of Nimbus-7 Earth radiation budget (ERB) products have shown that the global annual mean emitted longwave, absorbed shortwave, and net radiation were constant to within about + 0.5 W/sq m. Further, most of the small annual variations in the emitted longwave have been shown to be real. To obtain this measurement accuracy, the wide-field-of-view (WFOV) Earth-viewing channels 12 (0.2 to over 50 micrometers), 13 (0.2 to 3.8 micrometers), and 14 (0.7 to 2.8 micrometers) have been characterized in their satellite environment to account for signal variations not considered in the prelaunch calibration equations. Calibration adjustments have been derived for (1) extraterrestrial radiation incident on the detectors, (2) long-term degradation of the sensors, and (3) thermal perturbations within the ERB instrument. The first item is important in all the channels; the second, mainly in channels 13 and 14, and the third, only in channels 13 and 14. The Sun is used as a stable calibration source to monitor the long-term degradation of the various channels. Channel 12, which is reasonably stable to both thermal perturbations and sensor degradation, is used as a reference and calibration transfer agent for the drifting sensitivities of the filtered channels 13 and 14. Redundant calibration procedures were utilized. Laboratory studies complemented analyses of the satellite data. Two nearly independent models were derived to account for the thermal perturbations in channels 13 and 14. The global annual mean terrestrial shortwave and longwave signals proved stable enough to act as secondary calibration sources. Instantaneous measurements may still, at times, be in error by as much as a few Wm(exp -2), but the long-term averages are stable to within a fraction of a Wm(exp -2).

Kyle, H. Lee↗

High-Power Ion Thruster Technology

Performance data are presented for the NASA/Hughes 30-cm-diam 'common' thruster operated over the power range from 600 W to 4.6 kW. At the 4.6-kW power level, the thruster produces 172 mN of thrust at a specific impulse of just under 4000 s. Xenon pressure and temperature measurements are presented for a 6.4-mm-diam hollow cathode operated at emission currents ranging from 5 to 30 A and flow rates of 4 sccm and 8 sccm. Highly reproducible results show that the cathode temperature is a linear function of emission current, ranging from approx. 1000 C to 1150 C over this same current range. Laser-induced fluorescence (LIF) measurements obtained from a 30-cm-diam thruster are presented, suggesting that LIF could be a valuable diagnostic for real-time assessment of accelerator-arid erosion. Calibration results of laminar-thin-film (LTF) erosion badges with bulk molybdenum are presented for 300-eV xenon, krypton, and argon sputtering ions. Facility-pressure effects on the charge-exchange ion current collected by 8-cm-diam and 30-cm-diam thrusters operated on xenon propellant are presented to show that accel current is nearly independent of facility pressure at low pressures, but increases rapidly under high-background-pressure conditions.

Beattie, J. R.↗

Polar Magnetic Field Data

At this writing we have received all the CDROMs for the grant period. We have completed generating our timing tables past September 20, 2001. The calibration of the instrument has been checked for the entire mission up to the end of December 2000 and the key parameters provided to the project until the end of December 2000. These data are available to other experimenters over the web at http://www-ssc.igpp.ucla.edu/forms/polar/. High resolution spun data, 8 samples per see, have been created up to November, 2000 and have been made available to the community over the world wide web. This is a new data set that was a major effort this year. Our near term plans are to continue to provide key parameter data to the Polar project with the highest possible speed and to continue to reduce all high resolution magnetometer data and provide these data to the scientific community over the web.

Russell, Christopher T.↗

Coastal Atmosphere and Sea Time Series (CoASTS)

In this document, the first three years of a time series of bio-optical marine and atmospheric measurements are presented and analyzed. These measurements were performed from an oceanographic tower in the northern Adriatic Sea within the framework of the Coastal Atmosphere and Sea Time Series (CoASTS) project, an ocean color calibration and validation activity. The data set collected includes spectral measurements of the in-water apparent (diffuse attenuation coefficient, reflectance, Q-factor, etc.) and inherent (absorption and scattering coefficients) optical properties, as well as the concentrations of the main optical components (pigment and suspended matter concentrations). Clear seasonal patterns are exhibited by the marine quantities on which an appreciable short-term variability (on the order of a half day to one day) is superimposed. This short-term variability is well correlated with the changes in salinity at the surface resulting from the southward transport of freshwater coming from the northern rivers. Concentrations of chlorophyll alpha and total suspended matter span more than two orders of magnitude. The bio-optical characteristics of the measurement site pertain to both Case-I (about 64%) and Case-II (about 36%) waters, based on a relationship between the beam attenuation coefficient at 660nm and the chlorophyll alpha concentration. Empirical algorithms relating in-water remote sensing reflectance ratios and optical components or properties of interest (chlorophyll alpha, total suspended matter, and the diffuse attenuation coefficient) are presented.

Hooker, Stanford B.↗

Exploring scaling issues by using NASA Cold Land Processes Experiment(CLPX-1, IOP3) radiometric data

The NASA Cold-land Processes Field Experiment-1 (CLPX-1) involved several instruments in order to acquire data at different spatial resolutions. Indeed, one of the main tasks of CLPX-1 was to explore scaling issues associated with microwave remote sensing of snowpacks. To achieve this task, microwave brightness temperatures collected at 18.7, 36.5, and 89 GHz at LSOS test site by means of the University of Tokyo s Ground Based Microwave Radiometer-7 (GBMR-7) were compared with brightness temperatures recorded by the NOAA Polarimetric Scanning Radiometer (PSR/A) and by SSM/I and AMSR-E radiometers. Differences between different scales observations were observed and they may be due to the topography of the terrain and to observed footprints. In the case of satellite and airborne data, indeed, it is necessary to consider the heterogeneity of the terrain and the presence of trees inside the observed scene becomes a very important factor. Also when comparing data acquired only by the two satellites, differences were found. Different acquisition times and footprint positions, together with different calibration and validation procedures, can be responsible for the observed differences.

Tedesco, Marco↗

Estimating Software-Development Costs With Greater Accuracy

COCOMOST is a computer program for use in estimating software development costs. The goal in the development of COCOMOST was to increase estimation accuracy in three ways: (1) develop a set of sensitivity software tools that return not only estimates of costs but also the estimation error; (2) using the sensitivity software tools, precisely define the quantities of data needed to adequately tune cost estimation models; and (3) build a repository of software-cost-estimation information that NASA managers can retrieve to improve the estimates of costs of developing software for their project. COCOMOST implements a methodology, called '2cee', in which a unique combination of well-known pre-existing data-mining and software-development- effort-estimation techniques are used to increase the accuracy of estimates. COCOMOST utilizes multiple models to analyze historical data pertaining to software-development projects and performs an exhaustive data-mining search over the space of model parameters to improve the performances of effort-estimation models. Thus, it is possible to both calibrate and generate estimates at the same time. COCOMOST is written in the C language for execution in the UNIX operating system.

Baker, Dan↗

Constellations: A New Paradigm for Earth Observations

The last decade has seen a significant increase in the number and the capabilities of remote sensing satellites launched by the international community. A relatively new approach has been the launching of satellites into heterogeneous constellations. Constellations provide the scientists a capability to acquire science data, not only from specific instruments on a single satellite, but also from instruments on other satellites that fly in the same orbit. Initial results from the A-Train (especially following the CALIPSO/CloudSat launch) attest to the tremendous scientific value of constellation flying. This paper provides a history of the constellations (particularly the A-Train) and how the A-Train mission design was driven by science requirements. The A-Train has presented operational challenges which had not previously been encountered. Operations planning had to address not only how the satellites of each constellation operate safely together, but also how the two constellations fly in the same orbits without interfering with each other when commands are uplinked or data are downlinked to their respective ground stations. This paper discusses the benefits of joining an on-orbit constellation. When compared to a single, large satellite, a constellation infrastructure offers more than just the opportunities for coincidental science observations. For example, constellations reduce risks by distributing observing instruments among numerous satellites; in contrast, a failed launch or a system failure in a single satellite would lead to loss of all observations. Constellations allow for more focused, less complex satellites. Constellations distribute the development, testing, and operations costs among various agencies and organizations for example, the Morning and Afternoon Constellations involve several agencies within the U.S. and in other countries. Lastly, this paper addresses the need to plan for the long-term evolution of a constellation. Agencies need to have a replenishment strategy as some satellites age and eventually leave the constellation. This will ensure overlap of observations, thus providing continuous, calibrated science data over a much longer time period. Thoughts on the evolution of the A-Train will also be presented.

Kelly, Angelita C.↗

Analyzing Responses of Chemical Sensor Arrays

NASA is developing a third-generation electronic nose (ENose) capable of continuous monitoring of the International Space Station s cabin atmosphere for specific, harmful airborne contaminants. Previous generations of the ENose have been described in prior NASA Tech Briefs issues. Sensor selection is critical in both (prefabrication) sensor material selection and (post-fabrication) data analysis of the ENose, which detects several analytes that are difficult to detect, or that are at very low concentration ranges. Existing sensor selection approaches usually include limited statistical measures, where selectivity is more important but reliability and sensitivity are not of concern. When reliability and sensitivity can be major limiting factors in detecting target compounds reliably, the existing approach is not able to provide meaningful selection that will actually improve data analysis results. The approach and software reported here consider more statistical measures (factors) than existing approaches for a similar purpose. The result is a more balanced and robust sensor selection from a less than ideal sensor array. The software offers quick, flexible, optimal sensor selection and weighting for a variety of purposes without a time-consuming, iterative search by performing sensor calibrations to a known linear or nonlinear model, evaluating the individual sensor s statistics, scoring the individual sensor s overall performance, finding the best sensor array size to maximize class separation, finding optimal weights for the remaining sensor array, estimating limits of detection for the target compounds, evaluating fingerprint distance between group pairs, and finding the best event-detecting sensors.

Zhou, Hanying↗