Search NASA⌕ Search

SEARCH · Search NASA

Results for “Waste Form”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60

Near-Complete Retention of Technetium During Vitrification of Hanford Low Activity Waste With Recycle - 17315

Technetium is one of the more volatile radionuclides for which retention in low activity waste (LAW) glass under the high temperature conditions during vitrification can vary depending on feed composition, feed chemistry, and melter operating parameters. High retention of technetium in the glass is desirable in order to minimize the fraction of technetium that is directed to secondary waste streams, which include liquid off-gas treatment system effluents. Consequently, test data are crucial to assess and underpin the assumptions underlying such mass balance projections, the compositions of secondary waste streams, and, in particular, the effects of recycle on increasing the incorporation of technetium in the glass products and minimizing the fraction in non-glass waste forms. Previous testing performed on a scaled melter system that incorporates prototypical off-gas treatment components and real-time recycle of the liquid effluents back to the melter feed demonstrated that recycle resulted in significant increases of the incorporation of technetium into the LAW glass product and behavior that was in good agreement with process models for the system. However, the maximum technetium retention achieved in those tests was less than predicted. Tests conducted in the present work demonstrated, for the first time, near-complete retention of technetium in the LAW glass product with recycle. Holdup of technetium in the vacuum evaporator, which concentrates the liquid effluents prior to their recycle to the melter feed, was identified as the primary reason for the previously observed shortfall. The fate of other volatile constituents was also assessed. In particular, in addition to technetium, rhenium, which is frequently used as a non-radioactive surrogate for technetium, was included in these tests. This allows for a direct comparison of the behavior of rhenium and technetium during vitrification and in the down-stream processes. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

IMPACT OF TIME / TEMPERATURE CURING CONDITIONS AND ALUMINATE CONCENTRATIONS ON SALTSTONE PROPERTIES

This report addresses the impact of (1) the time and temperature curing conditions (profile) and (2) the impact of higher aluminate concentrations in the decontaminated salt solution on Saltstone processing and performance properties. The results demonstrate that performance properties as well as some of the processing properties of Saltstone are highly sensitive to the conditions of time and temperature under which curing occurs. This sensitivity is in turn dependent on the concentration of aluminate in the salt feed solution. In general, the performance properties and indicators (Young's modulus, compressive strength and total porosity) are reduced when curing is initially carried out under high temperature. However, this reduction in performance properties is dependent on the sequence of temperatures (the time/temperature profile) experienced during the curing process. That is, samples that are subjected to a 1, 2, 3 or 4 day curing time at 60 C followed by final curing at 22 C lead to performance properties that are significantly different than the properties of grouts allowed to cure for 1, 2, 3 or 4 days at 22 C followed by a treatment at 60 C. The performance properties of Saltstone cured in the sequence of higher temperature first are generally less (and in some cases significantly less) than performance properties of Saltstone cured only at 22 C. This loss in performance was shown to be mitigated by increased slag content or cement content in the premix at the expense of fly ash. For the sequence in which the Saltstone is initially cured at 22 C followed by a higher temperature cure, the performance properties can be equal to or greater than the properties observed with curing only at 22 C curing. The results in this report indicate that in order to meaningfully measure and report the performance properties of Saltstone, one has to know the time/temperature profile conditions under which the Saltstone will be cured. This will require thermal modeling and actual time/temperature profiles within the vaults under various pour schedules to determine (1) an average profile of time and temperature under normal processing conditions and (2) a conservative (worst case) time/temperature profile. Samples can then be cast and cured in the laboratory under these time and temperature profiles prior to measurement of the performance properties of the product waste forms From a processing perspective, a higher initial curing temperature decreased the set time to 1 day at both 40 C and 60 C and eliminated any bleed volume that was present for those samples that exhibited bleed at room temperature. However, the bleed water return system in the Saltstone Disposal Facility may remove bleed water before it can be reabsorbed. Aluminate concentrations at levels greater than 0.20 M in these salt solutions can lead to positive or negative effects on the performance properties. At a curing temperature of 22 C, aluminate increases Young's modulus and the compressive strength while reducing the total porosity. This generally corresponds to an improved (decreased) permeability (hydraulic conductivity) for Saltstone which is a positive outcome. On the other hand, with increased aluminate concentration there is a significant increase in heat of hydration that may limit pour schedule and must be considered in estimating the time/temperature profile to which Saltstone will be subjected during curing as discussed above. That is, higher temperatures in the vault (due to the higher heats of hydration) may present a greater challenge in controlling the curing time and temperature profile to achieve the desired performance properties.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Preparation and characterization of sodium bearing perovskite phases

Ceramic waste-forms constitute a major alternative to glass for immobilization of radionuclides in solid phase, with advantage of greater stability in the presence of water at moderate temperature. CaZrO{sub 3} and SrZrO{sub 3} with ABO{sub 3} perovskite structure are suitable host matrices for fixation of sodium and neodymium. Three new phases with compositions Na{sub 0.5}Nd{sub 0.5}ZrO{sub 3}, Ca{sub 0.44}Na{sub 0.28}Nd{sub 0.28}ZrO{sub 3} and Sr{sub 0.6}Na{sub 0.2}Nd{sub 0.2}ZrO{sub 3} have been synthesized and characterized as orthorhombic phases. The crystal structure of Ca{sub 0.44}Na{sub 0.28}Nd{sub 0.28}ZrO{sub 3} was derived from the crystallographic parameters of CaZrO{sub 3} using X-ray powder diffraction data in the orthorhombic system by Rietveld profile method. Preliminary leaching studies carried out in a digestion bomb showed low leachability of sodium and neodymium in water at 70 deg. C from Ca{sub 0.44}Na{sub 0.28}Nd{sub 0.28}ZrO{sub 3} matrix as compared to that from Sr{sub 0.6}Na{sub 0.2}Nd{sub 0.2}ZrO{sub 3} matrix.

36 MATERIALS SCIENCE↗

Synthesis of apatite phosphates containing Cs{sup +}, Sr{sup 2+} and RE{sup 3+} ions and chemical durability studies

Graphical abstract: New chemically durable hydroxy and fluoro apatite phosphate wasteforms CsLa{sub 0.8}Nd{sub 0.1}Sm{sub 0.1}Sr{sub 3}(PO{sub 4}){sub 3}OH and CsLa{sub 0.7}Nd{sub 0.1}Sm{sub 0.1}Eu{sub 0.1}Sr{sub 3}(PO{sub 4}){sub 3}F are fabricated. Display Omitted Highlights: ► Novel apatite phosphates CsLaSr{sub 3}P{sub 3}(PO{sub 4}){sub 3}OH and CsLaSr{sub 3}(PO{sub 4}){sub 3}F are reported. ► New hydroxyapatite wasteform CsLa{sub 0.8}Nd{sub 0.1}Sm{sub 0.1}Sr{sub 3}P{sub 3}O{sub 12}OH is fabricated. ► Fluoro analogue CsLa{sub 0.7}Nd{sub 0.1}Sm{sub 0.1}Eu{sub 0.1}Sr{sub 3}P{sub 3}O{sub 12}F incorporates ‘Eu{sup 3+}’. ► Negligible leachability of Cs and rare earth ions demonstrated. -- Abstract: Crystallization of Cs, Sr and selected rare earth ions in apatite phosphate structure was investigated. Compounds of the formula CsLaSr{sub 3}(PO{sub 4}){sub 3}OH (CSOH), CsLaSr{sub 3}(PO{sub 4}){sub 3}F (CSF) and the simulated waste forms of the compositions CsLa{sub 0.8}Nd{sub 0.1}Sm{sub 0.1}Sr{sub 3}(PO{sub 4}){sub 3}OH (CNSOH) and CsLa{sub 0.7}Nd{sub 0.1}Sm{sub 0.1}Eu{sub 0.1}Sr{sub 3}(PO{sub 4}){sub 3}F (CNSEF) were synthesized and characterized by powder XRD, TGA and SEM techniques. The leachability behaviour of the single phases was studied for a period of one month by MCC-5 test using powder specimen. The leachability of Cs and other rare earth ions was found to be negligible. The leach rates (LR{sub i}) of Sr and P were observed as follows: CSOH – LR{sub Sr} = 10{sup −3}–10{sup −4} g/m{sup 2}/d, LR{sub P} = 10{sup −4} g/m{sup 2}/d; CSF – LR{sub Sr} = 10{sup −3}–10{sup −5} g/m{sup 2}/d, LR{sub P} = 10{sup −4}–10{sup −5} g/m{sup 2}/d; CNSOH and CNSEF – LR{sub Sr} = 10{sup −3}–10{sup −4} g/m{sup 2}/d, LR{sub P} = 10{sup −4}–10{sup −5} g/m{sup 2}/d.

36 MATERIALS SCIENCE↗

Structure and thermodynamics of calcium rare earth silicate oxyapatites, Ca 2 RE 8 (SiO 4 ) 6 O 2 (RE = Pr, Tb, Ho, Tm)

Calcium rare earth silicate oxyapatites, (Ca 2 RE 8 (SiO 4 ) 6 O 2 ), are of interest as components of glass-ceramic nuclear waste forms. To assess their long-term behavior in a geologic repository, it is essential to determine their structure and thermodynamic stability at relevant conditions. Here, in this work, we performed detailed structural and thermodynamic investigations on Ca 2 Pr 8 (SiO 4 ) 6 O 2 , Ca 2 Tb 8 (SiO 4 ) 6 O 2 , Ca 2 Ho 8 (SiO 4 ) 6 O 2 , and Ca 2 Tm 8 (SiO 4 ) 6 O 2 by high energy synchrotron powder X-ray diffraction combined with Rietveld analysis and high temperature oxide melt drop solution calorimetry. Enthalpies of formation from constituent oxides (ΔH f,ox ) were determined to be -765.1 ± 22.8 kJ/mol for Ca 2 Pr 8 (SiO 4 ) 6 O 2 ; -638.9 ± 20.5 kJ/mol for Ca 2 Tb 8 (SiO 4 ) 6 O 2 ; -643.3 ± 10.3 kJ/mol for Ca 2 Ho 8 (SiO 4 ) 6 O 2 ; and -403.2 ± 5.1 kJ/mol for Ca 2 Tm 8 (SiO 4 ) 6 O 2 . These thermodynamic parameters were used in assessing the thermochemical stability of these phases in the presence of water vapor from room temperature to 600 K, as encountered in the subsurface environments of a geological repository.

36 MATERIALS SCIENCE↗

Evaluation of Groundwater Impacts to Support the National Environmental Policy Act Environmental Assessment for the INL Remote-Handled Low-Level Waste Disposal Project

Groundwater impacts have been analyzed for the proposed remote-handled low-level waste disposal facility. The analysis was prepared to support the National Environmental Policy Act environmental assessment for the top two ranked sites for the proposed disposal facility. A four-phase screening and analysis approach was documented and applied. Phase I screening was site independent and applied a radionuclide half-life cut-off of 1 year. Phase II screening applied the National Council on Radiation Protection analysis approach and was site independent. Phase III screening used a simplified transport model and site-specific geologic and hydrologic parameters. Phase III neglected the infiltration-reducing engineered cover, the sorption influence of the vault system, dispersion in the vadose zone, vertical dispersion in the aquifer, and the release of radionuclides from specific waste forms. These conservatisms were relaxed in the Phase IV analysis which used a different model with more realistic parameters and assumptions. Phase I screening eliminated 143 of the 246 radionuclides in the inventory from further consideration because each had a half-life less than 1 year. An additional 13 were removed because there was no ingestion dose coefficient available. Of the 90 radionuclides carried forward from Phase I, 57 radionuclides had simulated Phase II screening doses exceeding 0.4 mrem/year. Phase III and IV screening compared the maximum predicted radionuclide concentration in the aquifer to maximum contaminant levels. Of the 57 radionuclides carried forward from Phase II, six radionuclides were identified in Phase III as having simulated future aquifer concentrations exceeding maximum contaminant limits. An additional seven radionuclides had simulated Phase III groundwater concentrations exceeding 1/100th of their respective maximum contaminant levels and were also retained for Phase IV analysis. The Phase IV analysis predicted that none of the thirteen remaining radionuclides would exceed the maximum contaminant levels for either site location. The predicted cumulative effective dose equivalent from all 13 radionuclides also was less than the dose criteria set forth in Department of Energy Order 435.1 for each site location. An evaluation of composite impacts showed one site is preferable over the other based on the potential for commingling of groundwater contamination with other facilities.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Analysis of Selected Legacy 85 Kr Samples

Legacy samples composed of 85 Kr encapsulated in solid zeolite 5A material and five small metal tubes containing a mixture of the zeolite combined with a glass matrix resulting from hot isostatic pressing have been preserved. The samples were a result of krypton R&D encapsulation efforts in the late 1970s performed at the Idaho Chemical Processing Plant. These samples were shipped to Oak Ridge National Laboratory (ORNL) in mid-FY 2014. Upon receipt the outer shipping package was opened, and the inner package, removed and placed in a radiological hood. The individual capsules were double bagged as they were removed from the inner shipping pig and placed into individual glass sample bottles for further analysis. The five capsules were then x-ray imaged. Capsules 1 and 4 appear intact and to contain an amorphous mass within the capsules. Capsule 2 clearly shows the saw marks on the capsule and a quantity of loose pellet or bead-like material remaining in the capsule. Capsule 3 shows similar bead-like material within the intact capsule. Capsule 5 had been opened at an undetermined time in the past. The end of this capsule appears to have been cut off, and there are additional saw marks on the side of the capsule. X-ray tomography allowed the capsules to be viewed along the three axes. Of most interest was determining whether there was any residual material in the closed end of Capsule 5. The images confirmed the presence of residual material within this capsule. The material appears to be compacted but still retains some of the bead-like morphology. Based on the nondestructive analysis (NDA) results, a proposed path forward was formulated to advance this effort toward the original goals of understanding the effects of extended storage on the waste form and package. Based on the initial NDA and the fact that there are at least two breached samples, it was proposed that exploratory tests be conducted with the breached specimens before opening the three intact capsules. Portions of these would be analyzed to determine the fraction of krypton/xenon remaining in the matrix and the amount of rubidium remaining in the matrix. The inner surface of the breached capsules would be examined for corrosion. The materials contained in Capsules 2 and 5 have been examined. There appears to be a relatively uniform distribution of Kr and Rb throughout the pellets examined. The chemical composition of the pellets appears to be consistent with 5A molecular sieves. The material contained within Capsule 5 showed ~1 at. % lead. The origin of the Pb is currently indeterminate. X-ray diffraction analysis shows a significant shift from the 5A structure, most likely due to the Kr encapsulation / sintering process that occurred when the samples were made. The capsule walls were also examined and showed extensive corrosion throughout. Elemental mapping of the capsule material appeared consistent with carbon steel, while the weld material appeared consistent with a stainless steel. The interior surface of the capsule appeared to have a layer of material containing Al, Si, and Ca similar to the 5A molecular sieve. Analysis for Rb within the corrosion sites was inconclusive.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Requirements for a Dynamic Solvent Extraction Module to Support Development of Advanced Technologies for the Recycle of Used Nuclear Fuel

The Department of Energy's Nuclear Energy Advanced Modeling and Simulation (NEAMS) Program has been established to create and deploy next generation, verified and validated nuclear energy modeling and simulation capabilities for the design, implementation, and operation of future nuclear energy systems to improve the U.S. energy security. As part of the NEAMS program, Integrated Performance and Safety Codes (IPSC's) are being produced to significantly advance the status of modeling and simulation of energy systems beyond what is currently available to the extent that the new codes be readily functional in the short term and extensible in the longer term. The four IPSC areas include Safeguards and Separations, Reactors, Fuels, and Waste Forms. As part of the Safeguards and Separations (SafeSeps) IPSC effort, interoperable process models are being developed that enable dynamic simulation of an advanced separations plant. A SafeSepss IPSC 'toolkit' is in development to enable the integration of separation process modules and safeguards tools into the design process by providing an environment to compose, verify and validate a simulation application to be used for analysis of various plant configurations and operating conditions. The modules of this toolkit will be implemented on a modern, expandable architecture with the flexibility to explore and evaluate a wide range of process options while preserving their stand-alone usability. Modules implemented at the plant-level will initially incorporate relatively simple representations for each process through a reduced modeling approach. Final versions will incorporate the capability to bridge to subscale models to provide required fidelity in chemical and physical processes. A dynamic solvent extraction model and its module implementation are needed to support the development of this integrated plant model. As a stand-alone application, it will also support solvent development of extraction flowsheets and integrated safeguards approaches within the Fuel Cycle Research and Development (FCR&D) Program. The purpose of this document is to identify the requirements for this dynamic solvent extraction model to guide process modelers and code developers to produce a computational module that meets anticipated future needs.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

K-Basins Sludge Treatment and Packaging at the Hanford Site - 13585

Highly radioactive sludge resulting from the storage of degraded spent nuclear fuel has been consolidated in Engineered Containers (ECs) in the 105-K West Storage Basin located on the Hanford site near the Columbia River in Washington State. CH2M Hill Plateau Remediation Company (CHPRC) is proceeding with a project to retrieve the sludge, place it in Sludge Transport and Storage Containers (STSCs) and store those filled containers within the T Plant Canyon facility on the Hanford Site Central Plateau (Phase 1). Retrieval and transfer of the sludge material will enable removal of the 105-K West Basin and allow remediation of the subsurface contamination plumes under the basin. The U.S. Department of Energy (DOE) plans to treat and dispose of this K Basins sludge (Phase 2) as Remote Handled Transuranic Waste (RH TRU) at the Waste Isolation Pilot Plant (WIPP) located in New Mexico. The K Basin sludge currently contains uranium metal which reacts with water present in the stored slurry, generating hydrogen and other byproducts. The established transportation and disposal requirements require the transformation of the K Basins sludge to a chemically stable, liquid-free, packaged waste form. The Treatment and Packaging Project includes removal of the containerised sludge from T Plant, the treatment of the sludge as required, and packaging of all the sludge into a form that is certifiable for transportation to and disposal at WIPP. Completion of this scope will require construction and operation of a Sludge Treatment and Packaging Facility (STPF), which could be either a completely new facility or a modification of an existing Hanford Site facility. A Technology Evaluation and Alternatives Analysis (TEAA) for the STP Phase 2 was completed in 2011. A Request for Technology Information (RFI) had been issued in October 2009 to solicit candidate technologies for use in Phase 2. The RFI also included a preliminary definition of Phase 2 functions and requirements. Potentially applicable technologies were identified through a commercial procurement process, technical workshops, and review of the numerous previous sludge treatment technology studies. The identified technology approaches were screened using the criteria established in the Decision Plan, and focused bench top feasibility testing was conducted. Engineering evaluations of the costs, schedules, and technical maturity were developed and evaluated. Recommendations were developed based on technical evaluations. The criteria used in the evaluation process were as follows: (1) Safety, (2) Regulatory/stakeholder acceptance, (3) Technical maturity, (4) Operability and maintainability, (5) Life cycle cost and schedule, (6) Potential for beneficial integration with ongoing STP-Phase 1 activities, and (7) Integration with Site-wide RH-TRU processing/packaging, planning, schedule, and approach. The TEAA recommended Warm Water Oxidation (WWO) as the baseline treatment technology and two risk reduction enhancement options for further consideration during development of the process - size reduction and chemical oxidation (Fenton's reagent). The enhancement options would potentially allow a useful reduction in the total operating time required to process the K Basins sludge. The U.S. Department of Energy's Richland Field Office (DOE-RL) has approved this recommended technical approach. The baseline process can be broken down into the following main process steps: (1) STSC transfer from T Plant to the Sludge Treatment and Packaging Facility (STPF). (2) Retrieval of sludge from the STSCs and transfer to the Receipt and Reaction Tank (RRT). (3) Preparation for immobilization by oxidation using heated water (i.e., WWO) for those batches that require it and concentration by evaporating water at about atmospheric pressure in the RRT. (4) Immobilization by using additives to eliminate free liquids and packaging of the treated sludge into drums. (5) Inspection and handling of the filled drums prior to transfer to a separate storage and shipping facility. (6) Handling of vapor, condensate, and other waste streams generated by the process. Each of these steps is discussed in the paper, together with the current state of progress in developing the technology and requirements for continued development. A schematic of the recommended baseline WWO treatment process is given below. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Spectrophotometric and calorimetric studies of Np(V)complexation with sulfate at 10-70A degrees c

One of the approaches to safe management of highlevel nuclear wastes (HLW)calls for the disposal of HLW in geological repositories. Though the engineered barrier systems are expected to last a very long time after the repository is closed, they may gradually deteriorate and eventually lose integrity. consequently, water could contact the waste, dissolve it, and carry radionuclides out of the repository. Under the chemical environment in the vicinity of the waste form, 237Np(V) is one of the most soluble radionuclides and is most likely to be carried away from the repository. Because of its long half-life and high mobility, it is projected that, in the proposed Yucca Mountain Repository, the fractional dose attributed to 237Np will increase to 67% of the total dose in 75000 years [1]. As a result, the migration of Np in the postclosure chemical environment of the repository is a great concern to long-term repository performance. Because the temperature of the HLW repository could remain significantly higher than the ambient even thousands of years after the closure of the repository, predictions of the chemical behavior of Np in the repository can not be made without reliable thermodynamic data concerning the interactions of Np with the ligands that exist in the groundwater of the repository (e.g., OH–, F–, SO42– , PO43– and CO32) at elevated temperatures. Unfortunately, thermodynamic data on actinide complexation at elevated temperatures are scarce and highly scattered [2]. Lack of reliable geochemical thermodynamic data could lead to conservative decisions that have too big safety margins and raise the cost of the project. To help with the performance assessment of the HLW repository and fill the gap in thermodynamic data on actinide complexation at elevated temperatures, we have studied the complexation of actinides (Th, U, Np and Pu) with selected organic and inorganic ligands at elevated temperatures. This paper summarizes the results of the complexation of Np(V) with sulfate at 10–70°C.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

An Initial Study of Uranium Morphology in Fused LiCl-KCl

Molten salt electrorefining is one method by which reusable constituents within used nuclear fuel can be recovered for recycle and especially radiotoxic isotopes removed for incorporation into tailored waste forms. In these processes, irradiated metallic uranium or uranium alloys are dissolved at an electrochemical anode and crystals of purified uranium are collected at a cathode. The morphology of the deposited crystals can impact a variety of important factors, including the adhesion characteristics of the deposit to the cathode surface and the amount of salt which is macroscopically and microscopically occluded with the deposit. In addition, future applications such as direct creation of nuclear fuels by electrochemical deposition might be enabled if the science and fundamentals of uranium deposition morphology were thoroughly understood. A reasonable amount of experience has been collected from uranium electrorefining within the range of typical plant conditions. However, only limited laboratory study has been performed to define and understand the range of uranium crystal morphologies under repeatable laboratory conditions. The present study was an initial step to define these morphologies and transitions. The deposit from each deposition potential was primarily composed of a different morphology with little crossover of that morphology into the other deposition potentials. The spacing of these experiments (overpotentials of 25, 150 and 450 mV) is wide enough that additional dominant morphologies could exist. In addition, while the majority of the deposit from each potential was comprised of a particular morphology, minor morphologies were also found within the deposit. This may indicate the presence of an additional dimension of complexity, namely uranium concentration. Additional experimental and theoretical studies would be valuable to elucidate this subject. Additional results will be presented and discussed. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Thermodynamic Properties of Actinide-Zirconium Dioxide Solid-Solutions Relevant for Advanced Nuclear Fuels

Currently, spent nuclear fuel (SNF) from commercial reactors is composed of 95-99% UO{sub 2} and 1-5% fission products and transuranium elements. Thus, the primary waste form is the UO{sub 2} matrix, which over time will corrode to a variety of U(VI)-secondary phases. Alternative nuclear fuels, such as inert-matrix fuels and mixed-oxide fuels, have been studied for their in-reactor performance; however little research has been conducted to understand the behavior of these fuels as a wasteform. We use density functional theory and Monte-Carlo methods to understand the solid solution behavior of (Ac, Zr)O{sub 2} (Ac = Th, U, Np, Pu) phases. The end members of interest include ZrO{sub 2}, ThO{sub 2}, UO{sub 2}, NpO{sub 2}, and PuO{sub 2}, and all share the cubic-fluorite structure. The excess enthalpy of mixing ({delta}H{sub excess}), excess Gibbs free energy of mixing ({delta}G{sub excess}), and excess configurational entropy ({delta}S{sub excess}) are calculated for the above solid solution series, and from {delta}G{sub excess}, miscibility gaps are identified. In conclusion: Density functional theory and Monte Carlo simulations were used in this study to determine the thermodynamic properties of binary oxide solid solutions that are useful for advanced nuclear fuel applications. The DFT results for each solid solution series is of the single cubic unit cell; therefore, only one interaction parameter was calculated. Based on the Monte-Carlo results, on the order of 25% Zr can be incorporated into the AcO{sub 2} structures (Ac = Th, U, Np, or Pu). However, only trace amounts of the actinides can be incorporated into ZrO{sub 2}. Considering larger systems in the DFT calculations will improve results, because more cation-cation interaction parameters can be calculated. Configurational ordering can also be considered with larger systems. Molecular dynamic simulations will be used to determine the temperature dependence of the different solid solutions that is more specific to their respective lattice dynamics. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Preliminary Results of Voloxidation Processing of Kilogram Quantities of Used Nuclear Fuel

Advanced nuclear fuel processing methodologies are being studied as part of the Advanced Fuel Cycle Initiative (AFCI) program at ORNL. To support this initiative, processes and equipment were deployed at ORNL to perform all steps in the recycle process on actual used nuclear fuels, ranging from used fuel receipt to production of products and waste forms at the kilogram-scale (with capacity to process 20 kg of used fuel per year in up to four campaigns). In the first campaign, approximately 4 kg of used fuel was processed. As previously reported, the head-end processing was completed using saw-segmented Dresden fuel in lab-scale equipment in multiple batches. The second processing campaign used a new single pin shear and a new bench-scale voloxidizer to perform the dry head-end treatment prior to fuel dissolution. Approximately ~5 kg of used fuel (heavy metal basis) was processed in the second campaign. Two different fuels were oxidized in three separate batches to provide a range of processing conditions. The material used for each batch and general processing conditions are summarized in Table 1. Progress of the oxidation reaction was monitored continuously by two primary measurements; the concentration of oxygen in the effluent stream which was depressed as the oxygen was consumed, and the concentration of krypton-85 in the effluent stream as measured by a gamma counter on the off-gas pipeline. Table 1. Voloxidation test conditions for second campaign. Batch Fuel Source Burnup (GWd/MT)Batch size (kg*)/(kg**)Segment Length (in) Oxidation GasOperation Temperature ( C) 1Surry-2361.223/1.7041.0Air500 2North Anna63 702.071/2.8850.88Air600 3North Anna63 702.012/2.8030.88Oxygen600 * Heavy metal basis. ** Total fuel (oxide + cladding) basis. Fission product gases evolved from the fuel during the oxidation process were trapped for subsequent chemical and radiochemical analysis. The series of traps included a bed of molecular sieves to recover tritium (as HTO), silver-substituted zeolite to capture iodine (e.g. as AgI), a caustic scrubber to collect carbon dioxide (including 14CO2), a hydrogen-substituted mordenite to capture krypton (e.g. 85Kr) by cryogenic temperature swing adsorption, and a silver-substituted mordenite to capture xenon by cryogenic temperature swing absorption. The quantities of these volatile gases collected were compared to ORIGEN calculations to estimate the effectiveness of the voloxidation process to separate the volatiles from the used fuel. This paper will describe the voloxidation system and present preliminary results from the second processing campaign.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Predicting Saturated Hydraulic Conductivity over Time for Degrading Saltstone Vault Concrete - 20376

At the Savannah River Site (SRS), low-level liquid tank waste is mixed with cementitious materials to produce a solid, monolithic waste form referred to as saltstone. The liquid saltstone mixture is pumped into massive concrete structures referred to as saltstone disposal units (SDUs) for curing and long-term storage. SDUs are vaults made of high performance concrete forming a barrier between saltstone and the surrounding environment. Predicting the long-term performance of SDU vault concrete, as well as the saltstone material itself, is critical to understanding the potential releases of radionuclides to the surrounding environment as described in the Saltstone Disposal Facility (SDF) performance assessment (PA). The hydraulic conductivity profile for SDU vault concrete was conservatively assumed to degrade linearly from the initial saturated hydraulic conductivity of the intact concrete over a long period of time. The initial hydraulic properties of saturated SDU vault concrete have been measured, and the final hydraulic properties of degraded vault concrete are assumed to be the same as the porous backfill material that will surround the vault after closure. The assumed final condition of the vault concrete is also conservative in that it provides a greater estimate of water penetration through the vault than would generally be expected. Therefore, insights that provide more realistic but conservative estimates as to how degradation processes may change the hydraulic properties of the SDU vault concrete, the time dependent relationship of the vault concrete hydraulic properties to degradation (and thus time), and the final hydraulic properties of the vault concrete provides useful additions to the SDF PA. This paper focuses on the assumption that the saltstone vault concrete saturated hydraulic conductivity would decrease linearly as a function of degradation time; this assumption resulted from a worst-case, weighted (by relative layer thickness), arithmetic average of intact and backfill material hydraulic conductivities representing flow parallel to a layered system. This research indicates that the effective saturated hydraulic conductivity of the degraded SDU vault concrete should be based on the relative thickness-weighted geometric mean of the intact and degraded layers hydraulic conductivities. This alternative, which is supported extensively in the relevant literature and evaluated in this paper, leads to a more realistic and defensible estimate of the effective saturated hydraulic conductivity in degraded vault concrete while remaining conservative. The impact of using the more realistic estimate of the effective saturated hydraulic conductivity for the degraded concrete decreases the effective saturated hydraulic conductivity by up to several orders of magnitude for early times (i.e., when the SDU vault concrete is assumed degraded via sulfate attack and carbonation). This revised estimate of the effective saturated hydraulic conductivity has been implemented in the recently revised SDF PA. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Dynamic Leaching Method for Intact Salt-stone Samples - 18495

At the Savannah River Site (SRS) low activity salt solution is stabilized via encapsulation within a grout termed salt-stone. Salt-stone is emplaced into large (multi-million liter) concrete storage containers referred to as Salt-stone Disposal Units (SDUs). Technetium-99 (Tc-99) and iodine-129 (I-129) are long-lived radionuclides contained in the low activity salt waste and subsequently incorporated into the grout waste form: both radionuclides are contributors to the potential long-term radiation exposure of the public and environment surrounding the SDUs. With respect to Tc-99, in the reducing, high pH environment within the grout, Tc-99 is expected to be relatively immobile since it exists in a reduced Tc(IV) oxidation state in the form of sparingly soluble hydrated oxides (TcO{sub 2}.xH{sub 2}O) or sulfides (TcS{sub x}). However, in the presence of O{sub 2} (associated with the future infiltration of air or oxygenated ground waters into the salt-stone monolith) it is possible for redox-sensitive Tc(IV) to transition into highly soluble (and mobile) Tc(VII) species, such as pertechnetate (TcO{sub 4}{sup -}), which are more readily transported to the surrounding environment. In contrast, I-129 is highly soluble and its leaching behavior is not anticipated to be significantly impacted by potential changes in redox environment or pH within salt-stone. Traditional approaches to quantifying the leaching behavior of Tc-99 and I-29 from cementitious matrices have involved partitioning experiments using size-reduced (crushed/ground) samples, and determination of the radionuclide fraction immobilized by the cementitious solids. Such experiments create artificially high solid-liquid contact areas that likely result in higher Tc-99 and I-129 leachate concentrations than would be expected for intact, monolithic samples. In the current study a new technique, termed the Dynamic Leaching Method (DLM), is being used to initially investigate the Tc-99 leaching behavior from monolithic salt-stone samples; the system will be used at a later date to evaluate the leaching characteristics of I-129. The data derived using this technique is intended to inform the SRS Salt-stone Disposal Facility (SDF) Performance Assessment (PA) which models the long-term transport of radionuclides from the SDUs to the environment. The DLM utilizes a flexible-wall permeameter to achieve saturated leaching under an elevated hydraulic gradient to simulate and accelerate the future transport of groundwater through salt-stone. Leachates are regularly analyzed with respect to radionuclide concentrations, key constituent concentrations (e.g., Al, Ca, Mg, Na, Si, CO{sub 3}{sup 2-}, NO{sub 2}{sup -}, NO{sub 3}{sup -}, SO{sub 4}{sup 2-}), pH, and reduction potential (E{sub h}) in order to develop an understanding of how chemical changes associated with the pore solution influence grout weathering and radionuclide leaching behavior. This paper provides a brief update with respect to data derived from preliminary Tc-99 leaching evaluations as the DLM was being developed, but the paper is predominantly focused on new sample data in which the DLM technique, pre- and post-DLM salt-stone sample characterization, and leachate analysis protocols have been optimized. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Chemical Complexity Controls Energy Dissipation and Defect Evolution

The development of metallic alloys is arguably one of the oldest sciences, dating back at least 3,000 years. Most research and applications have been focused on alloys with comprised multiple phases with one or two dominant elements, to which the addition of alloying elements in low concentrations leads to various performance improvements and changes in radiation resistance. In sharp contrast to traditional alloys, recent success in the synthesis of single phase concentrated solid solution alloys (SP-CSAs) has opened up new frontiers in materials research. In these alloys, a random arrangement of multiple elemental species on a lattice (fcc or bcc) results in unique site-to-site lattice distortions and local disordered chemical environments. Intense radiation in nuclear fission and fusion energy power systems, nuclear waste forms, high-energy accelerators and space exploration transfers energy to the electrons and atoms that make up the material, and thereby produces defects that ultimately compromise material strength and lifetime. A grand challenge in materials research is to understand complex electronic correlations and non-equilibrium atomic interactions, and how such intrinsic properties and dynamic processes affect energy transfer and defect evolution in irradiated materials. Since SP-CSAs possess unique links between intrinsic material properties (can be altered by alloy complexity), energy dissipation and various defect dynamic processes; they are ideal systems to fill knowledge gaps between electronic- /atomic-level interactions and radiation resistance mechanisms. In our work, we show that chemical disorder and compositional complexity in SP-CSAs have an enormous impact on defect dynamics through substantial modification of energy dissipation pathways. Based on a closely integrated computational and experimental study using a novel set of Ni-based SP-CSAs, we have explicitly demonstrated that increasing chemical disorder can lead to a substantial reduction in the electron mean free path and electrical and thermal conductivity. These reductions have a significant impact on energy dissipation and consequentially on defect evolution during ion irradiation. Considerable enhancement in radiation resistance with increasing chemical complexity from pure nickel to binary, and to more complex quaternary solid solutions, is observed under ion irradiation. Contrary to conventional alloys with low solute concentration but multiple phases, energy dissipation and defect evolution at the level of electrons and atoms in SP- CSA systems with extreme compositional disorder is an unexplored frontier in materials science. The integrated experimental/modeling effort provides new insights into defect dynamics at the level of atoms and electrons, and an innovative path forward towards solving a long-standing challenge in structural materials. Increasing chemical complexity achieved orders-of-magnitude reductions in electron mean free paths and electron and thermal conductivities of alloys of NiCo, NiFe and NiCoFeCr, compared to Ni, and suppressed damage accumulation under ion irradiation. This discovery provides insights to address the grand challenge of understanding complex electronic correlations and non-equilibrium atomic interactions, and the effect of these intrinsic properties and dynamic processes on energy transfer and defect evolution in irradiated materials. Understanding how material properties and defect dynamics can be tailored by alloy complexity may pave the way for new design principles of functional alloys. (authors)

36 MATERIALS SCIENCE↗

A Novel Mobile Examination and Remediation Facility for On-Site Remediation of Dry Storage Systems - 18389

Most of the spent nuclear fuel (SNF) in dry storage in the United States is safely and securely stored in dual-purpose (i.e., storage and transportation) canisters [1]. However, some of the SNF is stored in storage-only (i.e., non-transportable) packages, or packages that may become nonconforming for continued storage or transportation for a variety of reasons. Currently, the capability to remediate dry storage systems (DSSs) for SNF that are not transportable or that need to be repaired to maintain confinement boundary integrity during storage service does not exist without on-site access to a spent fuel pool. Hence, there is a potential future need for a mobile facility with remediation capabilities that can be used at multiple storage installations. These capabilities would permit needed repairs to an existing DSS to support continued storage or for the dry transfer of fuel to a new conveyance suitable for transport, if necessary. This is a technical paper that does not take into account the contractual limitations under the Standard Contract for Disposal of Spent Nuclear Fuel and/or High-Level Radioactive Waste (Standard Contract) (10 CFR Part 961). Under the provisions of the Standard Contract, DOE does not consider spent nuclear fuel in canisters to be an acceptable waste form, absent a mutually agreed to contract amendment. To the extent discussions or recommendations in this paper conflict with the provisions of the Standard Contract, the Standard Contract provisions prevail. A novel design concept for a Mobile Examination and Remediation Facility (MERF) is proposed with functions and capabilities to remediate a DSS. The proposed MERF would be a multi-purpose facility, remotely operated and computer-controlled with semi-automated equipment to allow trained operators to safely perform remediation activities while keeping worker radiation dose as low as reasonably achievable. It would include a shielded rotating platform with support towers and would use commercial off- the-shelf examination and repair equipment. A slip ring arrangement underneath the rotating platform would allow for the power supply without impeding the continuous rotation and would simplify cable management. The support towers would be mounted on the rotating platform, and each tower would have vertical and horizontal positioning capability for axial and radial tool location. The rotating platform would be attached to the main MERF structure. Capabilities would include visual, surface, and volumetric examinations to fully characterize physical conditions on canister surface before and after a repair; repair techniques, e.g., laser beam welding, friction stir welding, or cold spray, to perform needed remediation activities; and associated equipment for surface preparation such as cutting and grinding equipment. The proposed design would be simple, modular, robust, economically viable, and easily transportable and would have a small footprint. The modular design would present several advantages including compatibility with a variety of different DSSs, on-site assembly, and transportability; it also would be built in interchangeable sections to facilitate decontamination. Further, shielding would be supplemented through interface with the existing transfer cask and storage overpack. Robustness and canister stability would be achieved using pneumatic holders and steel support structures designed with vibration absorbers to reduce impacts and/or a 'pendulum' effect during a seismic event. Thus, the proposed MERF would be designed to: (i) minimize handling of an affected DSS to the extent practicable, (ii) provide radiation shielding and minimize dose to operators and the public during remediation activities, and (iii) enable examination, repair, and repackaging. This paper describes the proposed MERF design concept and capabilities, main components, equipment, different modes of operation, and operating procedures. Structural and safety assessments would need to be performed before final design, licensing, and deployment. The MERF is evaluated with respect to regulatory impact (first of a kind, prior experience), operational impact (safety, security, staffing, ongoing operations, constraints), worker dose (low, medium, high), cost (low, medium, high), schedule (duration, time sequence), and technology readiness level. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Effect of Curing Temperature and Composition on the Performance Properties of Saltstone - 12473

When freshly mixed Saltstone is placed into a vault at the Savannah River Site, the heat of hydration produced during curing causes the temperature of the grout to increase. It is not uncommon for the temperature of the grout to increase by 30 to 50 deg. C above the starting temperature depending on the vault size and location, environmental conditions and pour schedule. For example, temperatures measured by thermocouples in one cell have exceeded 70 deg. C. The elevated temperatures, once reached, can extend for weeks or even months. Recent studies at Savannah River National Laboratory (SRNL) have shown that curing simulated Saltstone mixes at elevated temperatures can lead to reduced compressive strength and dynamic Young's modulus as well as increased total porosity when compared to the same grout mixes cured at 20 deg. C. Samples cured at 60 deg. C can have hydraulic conductivities approximately 600 times greater than samples cured at 20 deg. C. Previous studies have shown that the 60 deg. C cured mix had a dynamic Young's modulus that was half that of the mix cured at 20 deg. C. However, high temperature curing may not always have negative effects on the performance properties of the grout. These results indicate that higher curing temperatures can significantly alter the performance properties that are inputs for the Saltstone Performance Assessment. The Saltstone formulation (mix design) must produce a grout waste form that meets both placement and performance properties. A statistically designed set of mixes was developed to determine key process and compositional factors that affect the performance properties of Saltstone grout. A total of 27 mixes were batched and tested. There are eight baseline mixes that contain high and low values of aluminate concentration, varying w/p ratio, and varying fly ash content in the premix. Each of the eight mixes was cured at 22, 40 and 60 deg. C. The three additional reference mixes batched at the beginning, middle and end of testing showed good reproducibility throughout the study. The results of varying the operational and compositional factors on the performance properties of Saltstone grout are: - The Young's modulus is inversely affected by the curing temperature of the grout. - The aluminate content of the salt solution increases the Young's modulus of the Saltstone for samples cured at 20 and 40 deg. C. - All grouts cured at 60 deg. C have low Young's moduli and the composition of the grout mix did not have any positive effects on the performance properties after curing at this temperature. - The fly ash content in the premix had not discernible effect on the Young's modulus. - The water to premix ratio does not affect the Young's modulus. - Grouts made with the high aluminate salt solution have lower hydraulic conductivities than those made with the low aluminate simulant. - Temperature has an inverse effect on the hydraulic conductivity. - In general, increasing the water to premix ratio and the fly ash content will increase the hydraulic conductivity. - The porosity and cured density of the Saltstone grout are primarily a factor of the water to premix ratio of the grout formulation. The correlation between hydraulic conductivity and Young's modulus investigated in previous studies was evaluated further in this report. The current data as well as data from previous studies was fitted by a second degree polynomial function with a 77.1 % R-squared value. This model can be used to estimate the hydraulic conductivity of a sample based its Young's modulus for a limited range (E values up to 7 GPa). More data points should be included to further define the relationship between these performance properties are high Young's moduli and low hydraulic conductivities. The Young's modulus should still be measured on grouts formulated in future studies to be used as screening method for samples to be sent for hydraulic conductivity measurements. Saltstone grout has a complicated microstructure that is affected by the composition of the salt solution, the dry feed mixture composition, and the conditions under which it cures. The performance properties investigated are interrelated, which can make it difficult to determine individual relationships between various factors. Porosity is a large factor in determining both the Young's modulus and the hydraulic conductivity of the samples. Although the cured density is a straightforward measurement, it is not a significant performance property that needs further investigation. The porosity measurement provides similar and more meaningful data in relation to other performance properties. Based on the results of this study, the aluminate content of the salt solution does have an effect on the Young's modulus and the hydraulic conductivity and its effects should continue to be investigated. However, a new projection of aluminate contents should be used since projections change over time. The variability of fly ash in the premix did not prove to be a contributing factor that effects the performance properties of Saltstone and does not need to be included in future studies unless significant deviations from the baseline mix are proposed. The water to premix ratio has a significant effect on the performance properties of interest and the effects of varying this factor need further investigation. It is recommended that smaller ranges of w/p are investigated in order to provide data that is more relevant to the Saltstone being placed in the vaults. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗