Search NASA⌕ Search

SEARCH · Search NASA

Results for “component testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60

Space station propulsion technology: Space station propulsion system test bed test plan

Testing of the hydrogen/oxygen Space Station Propulsion System will demonstrate the technology readiness for the IOC application. To facilitate early demonstration of this technology and to allow demonstration of maturing technology, this testing will be performed with the components installed on a test bed which simulated the Space Station Structure. The test plan contains a description of the test bed, test objective, instrumentation plan, and controls plan. Each of these is discussed in detail.

Briley, G. L.↗

Construction and testing of ceramic fabric heat pipe with water working fluid

A prototype ceramic fabric/titanium water heat pipe has been constructed and tested; it transported 25 to 80 W of power at 423 K. Component development and testing is continuing with the aim of providing an improved prototype, with a 38 micron stainless steel liner covered by a biaxially-braided Nextel (trademark) sleeve that is approximately 300 microns thick. This fabric has been tested to 800 K, and its emittance is about 0.5 at that temperature. Advanced versions of the water heat pipe will probably require a coating over the ceramic fabric in order to increase this emittance to the 0.8 to 0.9 range.

Antoniak, Zenen I.↗

Influence of Back-Up Bearings and Support Structure Dynamics on the Behavior of Rotors With Active Supports

This report presents a synopsis of the research work. Specific accomplishments are itemized below: (1) Experimental facilities have been developed. This includes a magnetic bearing test rig and an auxiliary bearing test rig. In addition, components have been designed, constructed, and tested for use with a rotordynamics test rig located at NASA Lewis Research Center. (2) A study of the rotordynamics of an auxiliary bearing supported T-501 engine model was performed. (3) An experimental/simulation study of auxiliary bearing rotordynamics has been performed. (4) A rotordynamical model for a magnetic bearing supported rotor system, including auxiliary bearing effects has been developed and simulation studies performed.(5) A finite element model for a foil bearing has been developed and studies of a rotor supported by foil bearings have been performed. (6) Two students affiliated with this project have graduated with M.S. degrees.

Flowers, George T.↗

Third-Generation TiAl Alloy Tested: Exhibits Promising Properties for Rotating Components

The Revolutionary Turbine Accelerator/Turbine-Based Combined Cycle (RTA/TBCC) Program for the next-generation launch vehicle has targeted gamma titanium aluminide as a potential compressor and structural material. Because of the high compressor inlet and exit temperatures, the TBCC engine requires higher temperature materials than conventional Ti alloys, and because of its stringent thrust-to-weight requirements, the engine requires low-density material to be utilized wherever possible. Third-generation gamma alloys offer higher temperature capability along with low density and high stiffness. A high-temperature, high-strength *-TiAl alloy with a high Nb-content (Gamma MET PX1) was selected for evaluation. The microstructure and mechanical properties of Gamma Met PX (GMPX) in both the as-extruded and a lamellar heat-treated condition and the influence of the microstructure on the tensile, creep, and fatigue properties were investigated in-house.

Draper, Susan L.↗

A substructure energy method for prediction of Space Shuttle modal damping

The results of this program demonstrate the validity of a dissipative energy approach for predicting the damping of a four-component Space Shuttle model by means of modal parameters obtained from tests of the individual components. A relationship between modal damping energy per cycle and peak strain (or kinetic) energy is first determined empirically from test data for each component. Undamped analytical models of each component are also developed, and combined into a system model from which are obtained modal kinetic (or strain) energies for its respective modes. These data are then used with the empirical damping curves to apportion the proper amount of damping energy to each component in a combined system mode, and thereby allow a prediction of damping ratio.

Kana, D. D.↗

SSME component assembly and life management expert system

The space shuttle utilizes several rocket engine systems, all of which must function with a high degree of reliability for successful mission completion. The space shuttle main engine (SSME) is by far the most complex of the rocket engine systems and is designed to be reusable. The reusability of spacecraft systems introduces many problems related to testing, reliability, and logistics. Components must be assembled from parts inventories in a manner which will most effectively utilize the available parts. Assembly must be scheduled to efficiently utilize available assembly benches while still maintaining flight schedules. Assembled components must be assigned to as many contiguous flights as possible, to minimize component changes. Each component must undergo a rigorous testing program prior to flight. In addition, testing and assembly of flight engines and components must be done in conjunction with the assembly and testing of developmental engines and components. The development, testing, manufacture, and flight assignments of the engine fleet involves the satisfaction of many logistical and operational requirements, subject to many constraints. The purpose of the SSME Component Assembly and Life Management Expert System (CALMES) is to assist the engine assembly and scheduling process, and to insure that these activities utilize available resources as efficiently as possible.

Ali, M.↗

Integrated Liquid Bismuth Propellant Feed System

A prototype bismuth propellant feed and control system was constructed and tested. An electromagnetic pump was used in this system to provide fine control of the hydrostatic pressure, and a new type of in-line flow sensor was developed to provide an accurate, real-time measurement of the mass flow rate. High-temperature material compatibility was a driving design requirement for the pump and flow sensor, leading to the selection of macor for the main body of both components. Post-test inspections of both components revealed no cracks or leaking in either. In separate proof-of-concept experiments, the pump produced a linear pressure rise as a function of current that compared favorably with theoretical pump pressure predictions, with a pressure of 10 kPa at 30 A. Flow sensing was successfully demonstrated in a bench-top test using gallium as a substitute liquid metal. A real-time controller was successfully used to control the entire system, simultaneously monitoring all power supplies and performing data acquisition duties.

Polzin, Kurt A.↗

Demisability of GFRP and CFRP Components of Reentering Orbital Debris: Phase I Test Results

Observations of surviving reentry debris on the ground and research performed by Hyperschall Technologie Göttingen (HTG) [1] indicated that significantly more glass fiber-reinforced polymer (GFRP) and carbon fiber-reinforced polymer (CFRP) components survive reentry than current models predict. NASA’s Orbital Debris Program Office conducted a series of tests to evaluate the accuracy of material demise models for reentering orbital debris used in NASA’s Object Reentry Survival Analysis Tool (ORSAT) and Debris Assessment Software (DAS). Testing is planned in a multi-phase series to allow for quick quantification of results as well as refinement of methods resulting from lessons learned during early phases. The Phase 1 tests discussed here validated ORSAT models for homogeneous metals, provided an efficient quantification of composite material demisability properties like mass loss rate and overall time to demise, and identified potential failure modes, which are currently not well understood. Phase 2 tests will be used to further understand mass loss rates and modes of both thermal and mechanical failure in composite materials. The authors exposed 95 samples of aluminum, CFRP, Kevlar fiber-reinforced polymer, GFRP, and sheets of G10 fiberglass to conditions approximating the reentry environment using an inductively coupled plasma (ICP) torch facility. The cylindrical CFRP samples were exposed to the atmospheric pressure plasma, at both the end and the midpoint, to investigate the difference in demisability between parts with exposed edges, like panels, and parts with no edges, such as carbonoverwrapped pressure vessels (COPVs). In a non-oxidative environment, no composite materials demised within the 5-minute test time. In the oxidative, elevated heat flux environment, CFRP samples demised between 210 s and 270 s. For the first 100 s of insertion time, most of the mass loss was due to pyrolysis of resin, creating an approximately bi-linear mass-loss rate curve with time. In a non-oxidative environment, carbon filaments were observed to unravel from some of the CFRP end-burned samples; however, this effect did not seem to affect the overall time to demise for the samples significantly. These results indicate that both GFRP and CFRP components survive reentry with significantly more remaining mass than current models predict.

Greene, Benton R.↗

Capability for aerothermal-structural tests of large-to-full-scale components of future space transportation systems

The design of viable, low-mass thermostructural concepts for future space transportation systems requires accurate definition of the localized heat flux, pressures, and flow-surface interaction parameters for complex flow regions of detailed areas of large vehicles, such as wing-elevon coves, thermal protection system tile gaps, and corrugated metallic surfaces. This paper discusses investigations recently conducted in and planned for two high-energy wind tunnels at the Langley Research Center - the 8-foot High-temperatures Tunnel and the Thermal Protection System Test Facility. The data obtained on large-to-full-scale vehicle components, comparisons of the experimental data with theory, and the large, reusable, generalized test apparatus available at or planned for these facilities are discussed.

Couch, L. M.↗

Maturing Pump Technology for EVA Applications in a Collaborative Environment

The transition from low earth orbit Extravehicular Activity (EVA) for construction and maintenance activities to planetary surface EVA on asteroids, moons, and, ultimately, Mars demands a new spacesuit system. NASA's development of that system has resulted in dramatically different pumping requirements from those in the current spacesuit system. Hamilton Sundstrand, Cascon, and NASA are collaborating to develop and mature a pump that will reliably meet those new requirements in space environments and within the design constraints imposed by spacesuit system integration. That collaboration, which began in the NASA purchase of a pump prototype for test evaluation, is now entering a new phase of development. A second generation pump reflecting the lessons learned in NASA's testing of the original prototype will be developed under Hamilton Sundstrand internal research funding and ultimately tested in an integrated Advanced Portable Life Support System (APLSS) in NASA laboratories at the Johnson Space Center. This partnership is providing benefit to both industry and NASA by supplying a custom component for EVA integrated testing at no cost to the government while providing test data for industry that would otherwise be difficult or impossible to duplicate in industry laboratories. This paper discusses the evolving collaborative process, component requirements and design development based on early NASA test experience, component stand alone test results, and near term plans for integrated testing at JSCs.

Hodgson, Edward↗

Optical fibers and components experiment (A0138-7)

Fiber optics permanent damages induced by ionizing radiation after a long exposure in space and after laboratory tests were examined. Irradiation tests performed with radioactive sources (Sr90 - Y90) were validataed, computer coses used for the fluence and dose profile were verified. The performance of fiber optics waveguides in a low altitude orbit, and the origin of transmission losses in the material were dtermined. High sensitivity to ionizing radiations, however, may be a restriction for optic fiber use on satellites. Irradiation tests on these components using neutrons, gamma rays, and X-rays are carried out. Radiation damage on opticao materials, however, is strongly linked to the test conditions.

Bourrieau, J.↗

PVD TBC experience on GE aircraft engines

The higher performance levels of modern gas turbine engines present significant challenges in the reliability of materials in the turbine. The increased engine temperatures required to achieve the higher performance levels reduce the strength of the materials used in the turbine sections of the engine. Various forms of Thermal Barrier Coatings (TBC's) have been used for many years to increase the reliability of gas turbine engine components. Recent experience with the Physical Vapor Deposition (PVD) process using ceramic material has demonstrated success in extending the service life of turbine blades and nozzles. Engine test results of turbine components with a 125 micrometer (0.005 in) PVD TBC have demonstrated component operating temperatures of 56-83 C (100-150 F) lower than uncoated components. Engine testing has also revealed the TBC is susceptible to high angle particle impact damage. Sand particles and other engine debris impact the TBC surface at the leading edge of airfoils and fracture the PVD columns. As the impacting continues the TBC erodes away in local areas. Analysis of the eroded areas has shown a slight increase in temperature over a fully coated area, however, a significant temperature reduction was realized over an airfoil without any TBC.

Bartz, A.↗

PVD TBC experience on GE aircraft engines

The higher performance levels of modern gas turbine engines present significant challenges in the reliability of materials in the turbine. The increased engine temperatures required to achieve the higher performance levels reduce the strength of the materials used in the turbine sections of the engine. Various forms of thermal barrier coatings (TBC's) have been used for many years to increase the reliability of gas turbine engine components. Recent experience with the physical vapor deposition (PVD) process using ceramic material has demonstrated success in extending the service life of turbine blades and nozzles. Engine test results of turbine components with a 125 micron (0.005 in) PVD TBC have demonstrated component operating temperatures of 56-83 C (100-150 F) lower than non-PVD TBC components. Engine testing has also revealed the TBC is susceptible to high angle particle impact damage. Sand particles and other engine debris impact the TBC surface at the leading edge of airfoils and fracture the PVD columns. As the impacting continues, the TBC erodes away in local areas. Analysis of the eroded areas has shown a slight increase in temperature over a fully coated area, however a significant temperature reduction was realized over an airfoil without TBC.

Antonio Maricocchi↗

A new approach for performing contamination control bakeouts in JPL thermal vacuum test chambers

Contamination control requirements for the Wide Field/Planetary Camera II (WF/PC II) are necessarily stringent to protect against post-launch contamination of the sensitive optical surfaces, particularly the cold charge coupled device (CCD) imaging surfaces. Typically, thermal vacuum test chambers have employed a liquid nitrogen (LN2) cold trap to collect outgassed contaminants. This approach has the disadvantage of risking recontamination of the test article from shroud offgassing during post-test warmup of the chamber or from any shroud warming of even a few degrees during the bakeout process. By using an enclave, essentially a chamber within a chamber, configured concentrically and internally within an LN2 shroud, a method was developed, based on a design concept by Taylor, for preventing recontamination of test articles during bakeouts and subsequent post-test warmup of the vacuum chamber. Enclaves for testing WF/PC II components were designed and fabricated, then installed in three of JPL's Environmental Test Lab chambers. The design concepts, operating procedures, and test results of this development are discussed.

Johnson, Kenneth R.↗