Search NASA⌕ Search

SEARCH · Search NASA

Results for “composite cathode”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60

Increasing the Thermal Stability of Aluminum Titanate for Solid Oxide Fuel Cell Anodes

Solid-oxide fuel cells (SOFCs) show great potential as a power source for future space exploration missions. Because SOFCs operate at temperatures significantly higher than other types of fuel cells, they can reach overall efficiencies of up to 60% and are able to utilize fossil fuels. The SOFC team at GRC is leading NASA's effort to develop a solid oxide fuel cell with a power density high enough to be used for aeronautics and space applications, which is approximately ten times higher than ground transport targets. layers must be able to operate as a single unit at temperatures upwards of 900'C for at least 40,000 hours with less than ten percent degradation. One key challenge to meeting this goal arises from the thermal expansion mismatch between different layers. The amount a material expands upon heating is expressed by its coefficient of thermal expansion (CTE). If the CTEs of adjacent layers are substantially different, thermal stresses will arise during the cell's fabrication and operation. These stresses, accompanied by thermal cycling, can fracture and destroy the cell. While this is not an issue at the electrolyte-cathode interface, it is a major concern at the electrolyte-anode interface, especially in high power anode-supported systems. electrolyte are nearly identical. Conventionally, this has been accomplished by varying the composition of the anode to match the CTE of the yittria-stabilized zirconia (YSZ) electrolyte (approx.10.8x10(exp -6/degC). A Ni/YSZ composite is typically used as a base material for the anode due to its excellent electrochemical properties, but its CTE is about 13.4x10(exp -6/degC). One potential way to lower the CTE of this anode is to add a small percentage of polycrystalline Al2TiO5, with a CTE of 0.68x10(exp -6/degC, to the Ni/YSZ base. However, Al2TiO5 is thermally unstable and loses its effectiveness as it decomposes to Al2O3 and TiO2 between 750 C and 1280 C. be used as additives to increase the thermal stability of Al2TiO5 in SOFC operating conditions without adversely affecting the electrochemical properties of the SOFC anode. Three candidate materials were chosen through an extensive literature review: MgO, Fe2O3, and ZrTiO4. Although all three have been shown to prevent Al2TiO5 decomposition under various conditions, their effectiveness in the temperature range and atmosphere of the SOFC has not yet been evaluated. Several batches of Al2TiO5 with varying amounts of additives were prepared, exposed to reducing and oxidizing atmospheres at elevated temperatures, and the resulting decomposition of Al2TiO5 was measured. The most promising additives were further evaluated with the goal of ultimately preparing low CTE anodes that are chemically compatible to current systems. Adding minor constituents to stabilize Al2TiO5 could ultimately preserve its low CTE for the life of the fuel cell and improve the cell's long-term performance without a drop in anode conductivity. Further, these low CTE filler additions could allow the use of new sulfur tolerant anode materials, improving the viability of SOFCs for future aeronautics and space applications. Every SOFC consists of a cathode and an anode separated by an electrolyte, These three One way to avoid this problem is to design the cell such that the CTEs of the anode and The objective of this summer research project was to evaluate several materials that could

Bender, Jeffrey B.↗

Dealloyed Pt-Cu Core-Shell Nanoparticle Electrocatalysts for Use in PEM Fuel Cell Cathodes

We report the synthesis, characterization, and single fuel cell testing of a novel class of nanostructured Pt-Cu alloy particle materials for use as oxygen reduction electrocatalyst in polymer electrolyte membrane fuel cells. The active phase of the Pt alloy nanoparticle catalysts is prepared by electrochemical dissolution (voltammetric dealloying) of Cu surface atoms from Cu-rich Pt-Cu alloy precursors. Bulk and surface structural and compositional characterization suggests that the dealloyed active catalyst phase consists of a core-shell structure in which a multilayer Pt rich shell is surrounding a Pt-poor alloy particle core. The electrocatalytic Pt mass activity of the dealloyed core-shell particles for the oxygen reduction reaction (ORR) exceeds that of state-of-the art Pt electrocatalyst by more than a factor of 4 and thus meets performance targets for fuel cell cathodes [Gasteiger, H. A.; Kocha, S. S.; Sompalli, B.; Wagner, F. T. Appl. Catal. B: Environ. 2005, 56, 9-35]. It is hypothesized that a reduced Pt-Pt distance near the particle surface, stabilized by the lattice-contracted alloy core, may explain the modification of the surface catalytic reactivity. Dealloying of base-metal-rich noble metal alloy precursors is proposed as a more general strategy toward modifying the surface catalytic properties of noble metal surfaces.

30 DIRECT ENERGY CONVERSION↗

pCAM precursor produced from electroextraction technology and its application in synthesis of NMC 811 cathode material

The synthesis and characterization of LiNi 0.8 Co 0.1 Mn 0.1 O 2 (LNMC811) cathodes produced from recycled hydroxide precursors obtained from spent lithium-ion batteries is evaluated. Two precursor batches (Sample 1 and Sample 2) are prepared using modified recycling processes to examine how residual impurities and processing conditions influence the properties of the regenerated materials. Structural and compositional characterization by X-ray diffraction, ICP and SEM shows that the recycled precursors exhibit layered hydroxide structures containing both α Ni(OH) 2 and β Ni(OH) 2 phases. Trace impurities including sodium, boron, and aluminum are detected and partially mitigated during processing, with boron found to play a beneficial role in electrochemical behavior. Following lithiation with lithium carbonate and lithium hydroxide at 800 °C under an oxygen rich atmosphere, the resulting LNMC811 materials show electrochemical performance comparable to conventionally synthesized cathodes. Sample 2, which contains higher boron levels and improved cation ordering, delivers an initial discharge capacity of 174 mAh g -1 and retains more than 93 percent of its capacity after 50 cycles. The stable cycling behavior and structural integrity of these materials demonstrate that recycled precursors can be converted into high performance layered cathodes and support recycling as a practical and sustainable route for lithium-ion battery manufacturing.

25 ENERGY STORAGE↗

Recognition of V3+/V4+/V5+ Multielectron Reactions in Na3V(PO4)2: A Potential High Energy Density Cathode for Sodium-Ion Batteries

Na3V(PO4)2 was reported recently as a novel cathode material with high theoretical energy density for Sodium-ion batteries (SIBs). However, whether V3+/V4+/V5+ multielectron reactions can be realized during the charging process is still an open question. In this work, Na3V(PO4)2 is synthesized by using a solid-state method. Its atomic composition and crystal structure are verified by X-ray diffraction (XRD) and neutron diffraction (ND) joint refinement. The electrochemical performance of Na3V(PO4)2 is evaluated in two different voltage windows, namely 2.5–3.8 and 2.5–4.3 V. 51V solid-state NMR (ssNMR) results disclose the presence of V5+ in Na2-xV(PO4)2 when charging Na3V(PO4)2 to 4.3 V, confirming Na3V(PO4)2 is a potential high energy density cathode through realization of V3+/V4+/V5+ multielectron reactions.

25 ENERGY STORAGE↗

Design concept of co-ionic conducting solid oxide electrolyte for stable operation in a cell-imbalanced fuel cell stack

A bilayer composite electrolyte comprising BaCe 0.85 Y 0.15 O 3-d (BCY15) – Gd 0.2 Ce 0.8 O 2-d (GDC20) at the anode side and BaZr 0.85 Y 0.15 O 3-d (BZY15) – Nd 0.1 Ce 0.9 O 2-d (NDC10) at the cathode side is designed for improving the stability of co-ionic conducting solid oxide fuel cells (SOFCs) in a cell imbalanced stack. Contrary to the single layer structured SOFCs, the bi-layer cell stably operates without electrode delamination under negative voltage conditions. We measure local internal p O 2 values using embedded Pt probes. Based on these values, local electronic conduction is estimated in combination with four probe DC conductivity measurements. It is found that n-type conductivity (~10 –3 Scm –1 ) and p-type conductivity (10 –5 –10 –4 Scm –1 ) are developed in the BCY15-GDC20 near the anode side and in the BZY15-NDC10 near the cathode side, respectively. Finally, the results indicate that local electronic conduction in electrolyte regions near both the anode and cathode interfaces is a crucial factor for the durability of co-ionic SOFCs under negative voltage operation. We therefore suggest the bi-layer configuration as a practical solution to protect co-ionic SOFCs in a cell-imbalanced stack.

25 ENERGY STORAGE↗

Hierarchical nickel valence gradient stabilizes high-nickel content layered cathode materials

High-nickel content cathode materials offer high energy density. However, the structural and surface instability may cause poor capacity retention and thermal stability of them. To circumvent this problem, nickel concentration-gradient materials have been developed to enhance high-nickel content cathode materials’ thermal and cycling stability. Even though promising, the fundamental mechanism of the nickel concentration gradient’s stabilization effect remains elusive because it is inseparable from nickel’s valence gradient effect. To isolate nickel’s valence gradient effect and understand its fundamental stabilization mechanism, we design and synthesize a LiNi 0.8 Mn 0.1 Co 0.1 O 2 material that is compositionally uniform and has a hierarchical valence gradient. The nickel valence gradient material shows superior cycling and thermal stability than the conventional one. The result suggests creating an oxidation state gradient that hides the more capacitive but less stable Ni 3+ away from the secondary particle surfaces is a viable principle towards the optimization of high-nickel content cathode materials.

25 ENERGY STORAGE↗

A Self-Healable Sulfide/Polymer Composite Electrolyte for Long-Life, Low-Lithium-Excess Lithium-Metal Batteries

Solid electrolyte-protected lithium-metal anodes promise energy-dense, safe cells. While sulfide solid electrolytes enable facile processability and fast ion transport, they suffer from complex chemo-mechanical issues, including Li plating-induced fracture and Li stripping-induced contact loss. To address these issues, a grafting approach is implemented to functionalize the sulfide solid electrolyte (Li 3,85 Sn 0.85 Sb 0.15 S 4 ) with a self-healing unit. This leads to a dynamic bonding between the solid electrolyte network and a mechanically robust polymer scaffold, which reversibly accommodates the volume changes of the lithium-metal anode. Thus, the approach improves the interfacial contact between the lithium-metal anode and the composite electrolyte, enabling stable cycling at a mild stack pressure (160 kPa). With a negative to positive capacity ratio equals to 1, pouch full cells with a high-nickel cathode (nickel content > 90%) and lithium-metal anode display 92% capacity retention for 140 cycles. Engineering the interface between solid electrolyte and the polymeric binder offers a promising pathway to address the chemo-mechanical issues.

36 MATERIALS SCIENCE↗

An Accelerated Testing and Analysis Framework for Qualification of Battery Materials

The continuously growing demand for batteries used within automotive, aviation, and grid applications has exacerbated the need to supplement critical battery material feedstocks, such as those for anode and cathode active materials. New or supplementary material sources, however, universally comprise unique material properties that can significantly affect the lifetime and performance of resultant batteries. As such, the influence of composition, microstructure, and morphology on electrochemical performance should be characterized quickly and accurately to accelerate commercialization of new material sources. This work introduces a tiered framework to quickly assess new material viability and understand the influence of physicochemical properties on battery performance. The Tier 1 testing described here is rapid and lower-effort to quickly recognize materials with fundamental flaws and potentially disqualify them. Later testing would require more time and effort but provide higher fidelity information with a goal of validating materials for specific applications. A case study examining various commercial sources of LiFePO4 (LFP) is presented, using Tier 1 of the protocol to identify rapid electrochemical and physicochemical signals that correlate with performance and to provide early go/no-go decisions on LFP materials without the need for long-term cycling data.

25 - ENERGY STORAGE↗

Unconventional irreversible structural changes in a high-voltage Li–Mn-rich oxide for lithium-ion battery cathodes

Making all-electric vehicles (EVs) commonplace in transportation applications will require affordable high-power and high-energy-density lithium-ion batteries (LIBs). The quest for suitable cathode materials to meet this end has currently plateaued with the discovery of high-voltage (≥4.7 V vs. Li + ), high capacity (~250 mAh/g) lithium–manganese-rich (LMR) layered composite oxides. In spite of the promise of LMR oxides in high-energy-density LIBs, an irreversible structural change has been identified in this work that is governed by the formation of a ‘permanent’ spin-glass type magnetically frustrated phase indicating a dominant AB 2 O 4 (A = Li, B = Mn) type spinel after a short-term lithium deintercalation (charging) and intercalation (discharging) process. Furthermore, reduction of transition metal (Mn) ions from the 4+ state (pristine LMR) to 3+ (cycled LMR), which alters the intercalation redox chemistry and suggests the presence of ‘unfilled’ lithium vacancies and/or oxygen vacancies in the lattice after cycling, has presented a major stumbling block. Finally, these situations result in both loss of capacity and fading of the voltage profile, and these combined effects significantly reduce the high energy density over even short-term cycling.

25 ENERGY STORAGE↗

Study of Fe-Co Nanocomposite Films

Moessbauer study of nanogranular ferromagnetic FeCo films is presented. Two ways of production of nanocomposite systems were employed: (i) hollow cathode plasma jet deposition process, and (ii) laser ablation from Fe-Co metallic targets by means of a KrF excimer laser and r.f. magnetron sputtering. Complementary information on the composition of the samples were obtained by nuclear magnetic resonance of {sup 57}Fe and {sup 59}Co nuclei, conversion electron Moessbauer spectroscopy, and high resolution transmission electron microscopy. The films contain crystalline nanoparticles, 5-20 nm in size, embedded in an amorphous matrix.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Texture and microstructure evolution in single-phase Ti{sub x}Ta{sub 1-x}N alloys of rocksalt structure

The mechanisms controlling the structural and morphological features (texture and microstructure) of ternary transition metal nitride thin films of the Ti{sub x}Ta{sub 1-x}N system, grown by various physical vapor deposition techniques, are reported. Films deposited by pulsed laser deposition, dual cathode magnetron sputtering, and dual ion beam sputtering have been investigated by means of x-ray diffraction in various geometries and scanning electron microscopy. We studied the effects of composition, energetic, and kinetics in the evolution of the microstructure and texture of the films. We obtain films with single and mixed texture as well as films with columnar ''zone-T'' and globular type morphology. The results have shown that the texture evolution of ternary transition metal nitrides as well as the microstructural features of such films can be well understood in the framework of the kinetic mechanisms proposed for their binary counterparts, thus giving these mechanisms a global application.

36 MATERIALS SCIENCE↗

Enhanced life ion source for germanium and carbon ion implantation

Germanium and carbon ions represent a significant portion of total ion implantation steps in the process flow. Very often ion source materials that used to produce ions are chemically aggressive, especially at higher temperatures, and result in fast ion source performance degradation and a very limited lifetime [B.S. Freer, et. al., 2002 14th Intl. Conf. on Ion Implantation Technology Proc, IEEE Conf. Proc., p. 420 (2003)]. GeF{sub 4} and CO{sub 2} are commonly used to generate germanium and carbon beams. In the case of GeF{sub 4} controlling the tungsten deposition due to the de-composition of WF{sub 6} (halogen cycle) is critical to ion source life. With CO{sub 2}, the materials oxidation and carbon deposition must be controlled as both will affect cathode thermionic emission and anti-cathode (repeller) efficiencies due to the formation of volatile metal oxides. The improved ion source design Extended Life Source 3 (Eterna ELS3) together with its proprietary co-gas material implementation has demonstrated >300 hours of stable continuous operation when using carbon and germanium ion beams. Optimizing cogas chemistries retard the cathode erosion rate for germanium and carbon minimizes the adverse effects of oxygen when reducing gas is introduced for carbon. The proprietary combination of hardware and co-gas has improved source stability and the results of the hardware and co-gas development are discussed.

36 MATERIALS SCIENCE↗

Ultra-short channel GaN high electron mobility transistor-like Gunn diode with composite contact

We present a numerical analysis on an ultra-short channel AlGaN/GaN HEMT-like planar Gunn diode based on the velocity-field dependence of two-dimensional electron gas (2-DEG) channel accounting for the ballistic electron acceleration and the inter-valley transfer. In particular, we propose a Schottky-ohmic composite contact instead of traditional ohmic contact for the Gunn diode in order to significantly suppress the impact ionization at the anode side and shorten the “dead zone” at the cathode side, which is beneficial to the formation and propagation of dipole domain in the ultra-short 2-DEG channel and the promotion of conversion efficiency. The influence of the surface donor-like traps on the electron domain in the 2-DEG channel is also included in the simulation.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Cost Competitive Process of Battery Grade Oxides Preparation from Aged LIBs

The increasing demand for lithium-ion batteries (LIBs) is driving development of advanced recycling and refining methods. In this project, new cathode active materials are prepared from recycled lithium battery materials and subsequently electrochemically evaluated in coin cells. In detail, scrap LIBs were mechanically processed into a metal rich black mass, then reductive acid leached into an aqueous metal solution, and finally high-purity metal hydroxide precursor materials were prepared by selective electrochemical flow precipitation. Closed-loop LIB recycling into active electrode materials will enable US manufacturers to break their reliance on foreign sources of critical materials. For example, electroextraction process used here has potential to significantly reduce chemical & water use as well as waste production as compared to traditional metallurgic techniques. To this end, electroextracted materials refined from used batteries were collected and processed to be tested as precursor cathode active material (pCAM). For this project, two samples of high purity recycled NMC hydroxide (~1 kg each) were received from N th Cycle’s Ohio demonstration facility. The NMC compositions of the two materials are similar, and the levels of impurities have been confirmed. Indeed, impurities like copper, boron and sodium are present in quantities that could negatively impact battery performance. However, some studies have demonstrated that the control of the quantity of elements like copper or boron may improve the electrochemistry properties of Lithium-NMC batteries. The principal objective is to determine the electrochemical performance of these 2 NMC hydroxide batches and clearly determine the effect of the impurities on the performance.

25 ENERGY STORAGE↗

A Combined Experimental and Theoretical Study on the Activity and Selectivity of the Electrocatalytic Hydrogenation of Aldehydes

A detailed mechanistic study of the electrochemical hydrogenation of aldehydes is presented toward the goal of identifying how organic molecules in solution behave at the interface with charged surfaces and what is the best manner to convert them. Specifically, this study focuses on designing an electrocatalytic route for ambient temperature post-pyrolysis treatment of bio-oil. Aldehyde reductions are needed to convert biomass into fuels or chemicals. A combined experimental and computational approach is taken toward catalyst design to provide testable hypotheses regarding catalyst composition, activity, and selectivity. Electrochemical hydrogenation mechanisms for benzaldehyde and pentanal reduction are found to proceed by a coupled proton-electron transfer process. Initial results show that Au, Ag, Cu, and C catalysts exhibit the highest conversion to alcohol products. These catalysts are suitable because they show high cathodic onset potentials for H2 formation and low cathodic onset potentials for organic reduction. Conversion of aromatic aldehydes is found to be appreciably higher than aliphatic ones. Classical molecular dynamics simulations of solvent and substrate mixtures in an electrolytic cell were performed to assess how species concentrations vary at the solid/liquid interface and in the bulk as a function of applied voltage. Results show that an increase in voltage in the electrolytic cell decreases organic and increases water mole fractions at the solid/liquid interface. In this current study, charged cathodic surfaces result in carbonyl orientations at the surface that do not favor electron transfer. Repulsion of organic substrates to the bulk must be compensated by strong adhesion to the electrode surface. Implications on catalyst choice and process design are discussed.

Pyrolysis Oil upgrading, Atomistic Simulations, El↗

Thermal Stability of LiNi x Mn y Co z O 2 Cathode Materials

Here, the thermal evolution of LiNi x Mn y Co z O 2 (NMC) lithium-ion battery electrode materials is examined at various states of charge (SOC) or lithium concentrations for a variety of Ni:Mn:Co ratios or electrode compositions. Synchrotron X-ray diffraction (XRD) combined with Rietveld analysis shows the onset decomposition temperatures of phases, decomposition products, lattice parameters, and phase fractions as a function of composition and SOC. SOC impacts the lattice parameters of the NMC phase, where a collapse of the c-axis in the NMC phases is noted due to lithium extraction. Among the compositions examined, the low-Ni NMC111 uncycled sample (NMC111 0% SOC) exhibited the highest thermal stability, with a decomposition temperature approximately 250 °C higher than that of NMC532 0% and NMC811 0%. When the SOC exceeds 50% (i.e., more than 0.4 mol of Li ions extracted), the influence of Ni content on the decomposition temperature becomes negligible, with decomposition occurring around 250−300 °C for all compositions. Ni content also affects the decomposition pathways: NMC111 tends to first form a TM 3 O 4 -type phase, where TM represents transition metals, before transforming into a TMO-type phase, whereas most of the NMC811 samples directly decompose into the TMO phase. The presence of metallic phases was confirmed by both XRD and thermogravimetric-differential scanning calorimetry (TGA-DSC) analysis, as a result of heating under inert conditions. The TGA-DSC results suggest that metallic phase formation is favored at lower SOC in samples with a higher Ni content. This work provides comprehensive insight into the thermal degradation pathways of NMC materials as a function of composition, SOC, and temperature.

Peng, Jian [Univ. of New South Wales, Sydney, NSW ↗

A Silica-Aerogel-Reinforced Composite Polymer Electrolyte with High Ionic Conductivity and High Modulus

High-energy all-solid-state lithium (Li) batteries have great potential as next-generation energy-storage devices. Among all choices of electrolytes, polymer-based systems have attracted widespread attention due to their low density, low cost, and excellent processability. However, they are generally mechanically too weak to effectively suppress Li dendrites and have lower ionic conductivity for reasonable kinetics at ambient temperature. Here, an ultrastrong reinforced composite polymer electrolyte (CPE) is successfully designed and fabricated by introducing a stiff mesoporous SiO 2 aerogel as the backbone for a polymer-based electrolyte. The interconnected SiO 2 aerogel not only performs as a strong backbone strengthening the whole composite, but also offers large and continuous surfaces for strong anion adsorption, which produces a highly conductive pathway across the composite. As a consequence, a high modulus of ≈0.43 GPa and high ionic conductivity of ≈0.6 mS cm -1 at 30°C are simultaneously achieved. Furthermore, LiFePO 4 –Li full cells with good cyclability and rate capability at ambient temperature are obtained. Full cells with cathode capacity up to 2.1 mAh cm -2 are also demonstrated. The aerogel-reinforced CPE represents a new design principle for solid-state electrolytes and offers opportunities for future all-solid-state Li batteries.

25 ENERGY STORAGE↗

Deposition of dielectric films on silicon using a fore-vacuum plasma electron source

We describe an experiment on the use of a fore-vacuum-pressure, plasma-cathode, electron beam source with current up to 100 mA and beam energy up to 15 keV for deposition of Mg and Al oxide films on Si substrates in an oxygen atmosphere at a pressure of 10 Pa. The metals (Al and Mg) were evaporated and ionized using the electron beam with the formation of a gas-metal beam-plasma. The plasma was deposited on the surface of Si substrates. The elemental composition of the deposited films was analyzed.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗